Gebruiksaanwijzing /service van het product 536,884,791 van de fabrikant Craftsman
Ga naar pagina of 19
5.0 Horsepower 22 Inch Dual Stage 120V, Electric Start SNOW THROWER MODEL NO, 536,884791 Caution: Read and follow all Safety Rules and Operating Instructions before first use of this product, SEARS, ROEBUCK AND CO.
il nP':_:) H= [o]= [o,[o]'_lld=l_',] Table of Contents 2 Service and Adjustments 14-t6 Warranty 2 Storage 17 Safety Rules 2-4 Troubleshooting 18 Contents of Shipping Carton 4-5 Repair P.
PREPARATION 1. Thoroughly inspect the area where the snow thrower is to be used and remove all doormats, sleds, boards, wires and other foreign objects. 2. Disengage all clutches before starting the engine (motor). 3. Do not operate the snow thrower without wearing adequate winter outer garments.
16. Never direct discharge at bystanders or allow anyone in front of the snow thrower. 17. Disengage power to the auger/impeller when snow thrower is transported or not in use. 18. Use only attachments and accessories approved by the manufacturer of the snow thrower (such as tire chains, electric start kits, etc).
Parts packed separately in carton (not shown full size) 2 - Ignition Keys (Attached to engine in plastic bag) 1 - Crank Assembly 1 - Snow Chute Assembly ,4k CAUTION: Always wear safety glasses or eye shields while assembling snow thrower.
• Remove and discard the packing material from around the snowthrower. • Cut all four corners of the carton from top to bottom and lay the panels flat. • Cut ties securing the clutch control cable to the lower handle and lay cable back away from the motor frame.
• Carefully remove cotter pin, clevis pin and drilled pin from yoke end of crank rod assembly (see figure below). • Place universal joint into end of worm gear lining up large holes. Insert drilled pin (ensure opening in pin is in line with small openings in universal joint) (see figure below).
Eo to] KNOW YOUR SNOW THROWER READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Compare the illustrations with your SNOW THROWER to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference.
Auger Drive Clutch Ignition Key insert to run pull out to stop Z_ CAUTION: Read owner's manual before operating machine. Never direct discharge toward bystanders. Release the auger control bar and stop the engine before unclogging discharge chute or auger housing and before leaving the machine.
BEFORE STARTING THE ENGINE • If the snow thrower must be moved with- out the aid of the engine, it is easier to pull the snow thrower by the handles rather than pushing. • Before you service or start the engine, fa- miliarize yourself with the snow thrower.
COLD START (See figure on this page) • Be sure the auger ddve lever is in the disengaged (Released) position, • Move the throttle control to '_ (Fast) position. • Remove the keys from the plastic bag. Insert one key into the ignition slot. Be sure it snaps into place.
• Push the primer button, see figure on page 8, while covering the vent hole as follows: (remove finger from primer but- ton between primes). One time if temperature is above 50oF. Two times if temperature is 50_F to 15°t:. Four times if temperature is below 15°F.
CUSTOMER RESPONSIBILITIES SERVICE RECORDS Fill in dates as you complete regular service Check Engine Oil Level Change Engine Oil Tighten All Screws & Nuts Lubricate Pivot Points Check Auger Clutch.
OIL RECOMMENDATION Only use high quality detergent oil rated with API service classification SG. Select the oil's viscosity grade according to your expected operating temperature. NOTE: For extreme cold operating condi- tions of 0 ° and below, use a partial synthetic OW30 motor oil for easier starting.
• Hold the square end of the threaded portion with pliers and adjust the Iocknut in or out until the excess slack is removed (see last figure on page 14). • Pull the cable back through the spring and connect the cable (see last figure on page 14).
mounting bolt. • Reinstall the belt cover. • Reconnect the spark plug wire. A(_dve Pulley " ,_._,,,,=_. Belt Guide ,--k -'-k" .8. Auger Idler _ Pulley Enga_ it _ _ .
Z_ CAUTION' Never store your snow thrower indoors'or in an enclosed, poorly ventilated area if gasoline remains in the tank. fumes may reach an open flame, spark or pilot light from a furnace, water heater, clothes dryer, cigarette, etc. To prevent engine damage (if snow thrower is not used for more than 30 days) follow the steps below.
TROUBLE CAUSE CORRECTION )ifficult starting Defective spark plug Replace spark plug Water or dirt in fuel system Use carburetor bowl drain to flush and refill with fresh fuel. Engine runs Blocked fuel line or low on fuel Clean fuel line; check fuel supply; erratically tank or stale gasoline add fresh fuel (gasoline/oil mix tura if 2-cycle engine).
19.
Een belangrijk punt na aankoop van elk apparaat Craftsman 536,884,791 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Craftsman 536,884,791 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Craftsman 536,884,791 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Craftsman 536,884,791 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Craftsman 536,884,791 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Craftsman 536,884,791 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Craftsman 536,884,791 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Craftsman 536,884,791 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.