Gebruiksaanwijzing /service van het product 536.7974 van de fabrikant Craftsman
Ga naar pagina of 17
CRR FTSMI:tW 4 Horsepower 9 Inch EDGER MODEL NO. 536.797400 Caution: Read and follow all Safety Rules and Operating Instructions before first use of this product.
Table of Contents 2 Warranty 2 Safety Rules 2-3 Contents of Shipping Carton 4 Assembly 4-6 Operation 7-10 Maintenance 11-12 Service and Adjustments 13-14 Storage 15 Troubleshooting 16 Edger Repair Par.
• Never removethe fuel tank cap or add fuel to a running or hot engine. • Never store fuel or Edger with fuel in the tank inside a building where fumes may reach an open flame. OPERATING SAFETY • Never allow children or young teenagers to operate the Edger.
Contents of Parts Bag (shown full size) (2) - Hex Head Nuts (2)- Hex Head Screws 5/16-18 5/16-18x 1-1/4 inch (2) - Hair Pins Parts packed separately in carton (not shown full size) 1 - Container SAE30 Oi1(20 ounces) (1) -Control Rod 1 - Owner's Manual (not shown) 1 - Parts Bag (not shown) Z.
TO ASSEMBLE THE EDGER ' • Pivot the upper handle upward being careful not to pinch or pull the engine control wire, until the mounting holes in the upper handle align with the mounting holes in the lower handle. Install (2) 5/16- 18 x 1-1/4 inch hex head screws and (2) 5/16-18 hex lock nuts (found in parts.
KNOW YOUR EDGER READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR EDGER. Comparethe illustrations with your EDGER to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. s, l I_- Fast Slow Stop Primer Button Engine Control Adjustable Rear Wheel Blade Guard .
Throttle Control - Used to control the en- gine speed. Primer Button - Injects fuel directly into the carburetor manifold for faster starts. Starter Handle - The engine on this edger is equipped with an easy pull recoil starter, Depth Control Lever - Controls the depth of the blade.
TO USE THE DEPTH CONTROL LEVER • Position your Edger in desired edging lo- cation, before operating. • Start the engine and move the depth control lever back to lower the cutting blade. • Select the edging depth you need. There are 4 selections up to approxi- mately 2-1/2 inches deep.
TO USE THE BEVEL CUT FEATURE Bevel edging reduces the need to edge as often creating a type of trench along your sidewalk, driveway and etc. Move the in- dex lever to the bevel cut position and se- cure index lever in the slot.
,/_ WARNING: Gasoline is flammable and caution must be used when handling or storing it. Do not fill fuel tank while Edger is running, hot, or when Edger is in an enclosed area. Keep away from open flame, electrical spark, and do not smoke while filling the fuel tank.
CUSTOMER RESPONSIBILITIES SERVICE RECORDS SCHEDULE Fill In dates as After Before Fre- E_ew Every Every Begin Before you complete First Each quently i 10 25 Each StoragG regular service 2 Use Hours Hours Hours Season Hours SERVICE DATES Lubricate aJt Pivot Points _ IJ Lubricate Wheel Axles t,/ Check Engine Oil Level t.
Oil Drain Plug AIR CLEANER Replace the filler once a year; more often under dusty or dirty conditions. DO NOT attempt to clean or oil the air filter. To install a new air filter, do the following: • Disconnect the spark plug wire from the spark plug.
Z_ CAUTION: Always stop the engine and disconnect the spark plug wire before making any repairs to the Edger. _BELT REPLACEMENT Your edger is equipped with a V-belt made of a special compound. If the belt becomes worn or breaks, replace it with an orignal equipment belt as shown in the Repair Parts section of this manual.
LEVELING ADJUSTMENT • whenthe depth control lever is in the forward adjustment slot, the engine platform should be approximately level and the edging blade tip should be 1-1/4 to t-1/2 inches above the surface of the ground.
WARNING: Never store your Edger indoors or in an enclosed, poorly ventilated area. If gasoline remains in the tank, fumes may reach an open flame, spark or pilot light from a furnace, water heater, clothes dryer, cigarette, etc. EDGER • Clean the Edger thoroughly; remove all debris and wipe the unit dry.
TROUBLE CAUSE CORRECTION Difficult starting Stale fuel Drain fuel tank, Fill with fresh fuel or Defective spark plug Clean and re-gap spark plug Clogged fuel line Replace fuel filter Engine runs errac.
For the repair or replacement parts you need delivered directly to your home Call 7 am-7 pm, 7 days a week 1-800-366-PART (1-800-366-7278) Para ordenar piezas con entrega a domicilio -1-800-659-7084 For in-house major brand repair service Call 24 hours a day, 7 days a week 1-800-4-REPAIR (1-800-473-7247) _ .
Een belangrijk punt na aankoop van elk apparaat Craftsman 536.7974 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Craftsman 536.7974 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Craftsman 536.7974 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Craftsman 536.7974 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Craftsman 536.7974 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Craftsman 536.7974 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Craftsman 536.7974 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Craftsman 536.7974 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
