Gebruiksaanwijzing /service van het product 917.27207 van de fabrikant Craftsman
Ga naar pagina of 60
Owner's Manual ICRRFTSMRN+I 17.0 HP ELECTRIC START 42" MOWER 6 SPEED TRANSAXLE LAWN TRACTOR Model No. 917.272070 • Safety = Assembly • Operation • Maintenance • Repair Parts This product has a low emission engine which operates differently from previously built engines.
Warranty ............................................... 2 Safety Rules ......................................... 3 Product Specifications .......................... 6 Assembly .............................................. 8 Operation ...............
IMPORTANT; This cutting machine is capable of amputating hands and feet and throwing objects, Failure to observe the following safety instructions could result in serious injury or death. I. GENERAL OPERATION • Read, understand, and follow all instructions in the manual and on the machine before starting.
III. CHILDREN Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to the machine and the mowing activity. Never assume that children will remain where you last saw them. • Keep children out of the mowing area and under the watchful care of another responsible adult.
• Use slow speed. Choose a low gear so that you will not have to stop or shift while on the slope. • Avoid starting or stopping on a slope. If tires lose traction, disengage the blades and proceed slowly straight down the slope. • If machine stops while going uphill, disengage blades, shift into reverse and back down slowly.
PRODUCT SPECIFICATIONS 3ASOLINE 1.25 GALLONS 3APACITY UNLEADED t_ND TYPE: REGULAR 31LTYPE SAE 10W30 (ABOVE 32°F) _.PI-SF-SJ): SAE 5W-30 (BELOW 32°F) OIL CAPACITY: W/FILTER: 4.0 PINTS W/OFILTER: 3.5 PINTS SPARK PLUG: CHAMPION RC12YC 3AP: .040") GROUND SPEED FORWARD: (MPH): 1 sT 1.
Steering Wheel Insert (1) Hex Bolt 3/8-16 x 1 Steerin__ Boot Steering Wheel (1) Lock washer 3/8 @(1) Locknut 5/16-18 _ Steering Wheel Adapter (1) Large Flat Washer (1) Hex Bolt 5/16-18 x 1-1/4 t teeri.
Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.
Label Batten,, Door Terminal INSTALL SEAT Adjust seat before tightening adjustment knob. 1. Remove adjustment knob and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor. 2. Pivot seat upward and remove from the cardboard packing.
INSTALL MULCHER PLATE (If previously removed) 1. Raise and hold deflector shield in upright position. 2. Place front of mulcher plate over front of mower deck opening and slide into place, as shown. 3. Hook front latch into hole on front of mower deck.
These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning. BATTERY CAUTION OR REVERSE FORWARD FAST SLOW WARNING ENGINE ON ENGINE OFF OIL P.
KNOWYOURTRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference.
The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or performing any adjustments or repairs. We recommend a wide vision safety mask over spectacles or standard safety glasses.
• The average lawn should be cut to approximately 2-1/2 inches during the cool season and to over 3 inches during hot months. For healthier and better looking lawns, mow often and after moderate growth.
TOWING CARTS AND OTHER ATTACHMENTS Tow only the attachments that are recommended by and comply with specifications of the manufacturer of your tractor. Use common sense when towing. Too heavy of a load, while on a slope, is dangerous. Tires can lose traction with the ground and cause you to lose control of your tractor.
COLD WEATHER STARTING ( 50 ° F and below) 6. When engine starts, allow engine to run with the throttle control in the choke position until the engine runs roughly, then move throttle control to fast position. This may require an engine warm-up period from several seconds to several minutes, depend- ing on the temperature.
MAINTENANCE SCHEDULE FILL IN OATES AS YOU COMPLETE REGULAR SERVICE Check Brake Operation I1_ II _ CheCk Tire Pressure _ I_ check Operalor Pre_ence and InterlOCk Systems I_ Checkfor LOOse Fasteners I_ .
TRACTOR Always observe safety rules when performing any maintenance. BRAKE OPERATION If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be ad- justed. (See "TO ADJUST BRAKE" in the Service and Adjustments section of this manual).
• Keep battery and terminals clean. • Keep battery bolts tight. • Keep small vent holes open. • Recharge at 6-10 amperes for 1 hour. NOTE: The original equipment battery on your tractor is maintenance free. Do not attempt to open or remove caps or covers.
Every 100 hours of operation (more often under extremely dusty, dirty conditions), remove the blower housing and other cooling shrouds. Clean the cooling fins and external surfaces as necessary.
C'am0 / / C,om Fuel Pi,ter CLEANING • Clean engine, battery, seat, finish, etc. of all foreign matter. • Keep finished surfaces and wheels free of all gasoline, oil, etc.
TO LEVEL MOWER HOUSING Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See "PROD- UCT SPECIFICATIONS" section of this manual). If tires are over or underinflated, you will not properly adjust your mower.
TO REPLACE MOWER BLADE DRIVE BELT The mower blade drive belt may be replaced without tools. Park the tractor on level surface. Engage parking brake. BELT REMOVAL - 1, Remove mower from tractor (See "TO REMOVE MOWER" in this section of this manual).
TRANSAXLE GEAR SHIFT LEVER NEUTRAL ADJUSTMENT The transaxle should be in neutral when the gear shift lever is in neutral (N) (lock gate) position. The adjustment is preset at the factory; however, if adjustment is needed, proceed as follows: 1. Make sure transaxle is in neutral (N).
Positive Terminal Negative Terminal .ex Bolt Positive Terminal Negative Terminal REPLACING BATTERY ,_CAUTION: Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc.
ENGINE Maintenance, repair, or replacement of the emission control devices and systems, which are being done at the customers expense, may be performed by any non-road engine repair establishment or individual. Warranty repairs must be performed by an authonzed engine manufectureCs service outlet.
Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. ,_ CAUT|ON: Never store the tractor with gasoline in the tank inside a building where fumes may reach an open flame or spark.
TROUBLESHOOTING CHART PROBLEM CAUSE CORRECTION Will not start Hard to start Enginewill not turn over Engine clicks but will not start i 1. Out of fuel. 2. Engine not "CHOKED" properly. 3. Engine flooded. 4. Bad spark plug. 5. Dirty air filter.
TROUBLESHOOTING CHART tROUBLESHOOTING CHART PROBLEM CAUSE Lossofpower 1. Cuttingtoo muchgrass/too Excessive vibration Enginecontinues to run when operator leaves seat with with attachment clutch engaged Poor cut - uneven fast. 2. Throttle in "CHOKE" position.
TROUBLESHOOTING CHART PROBLEM Mower blades will not rotate Poor grass discharge Headlight(s) not working (if so equipped) Battery will not charge Engine "backfires' when turning engine "OFF" CAUSE 11. Obstruction in clutch mechanism.
SCHEMATIC TRACTOR -- MODEL NUMBER 917.272070 RED _ED IGNITION SWITCH RELAY NON-REMOVABLE REMOVABLE CONNECTIONS CONNECTIONS WIRING INSULATED CLIPS NOTE: IF WIRING INSULATED CLIPS WERE REMOVED FOR SERVI.
ELECTRICAL TRACTOR - - MODEL NUMBER 917.272070 22 32.
ELECTRICAL TRACTOR - - MODEL NUMBER 917.272070 KEY PART NO. NO. DESCRIPTION 1 2 8 16 21 22 24 25 26 27 28 29 3O 33 4O 41 42 43 45 52 81 163465 Battery 74760412 Bolt Hex Hd 1/4-20unc x 3/4 156417 Case .
TRACTOR - - MODEL NUMBER 917.272070 CHASSIS AND ENCLOSURES 29 _1S9 17-- , 60_ 1_ _ // /30 212_ 3g 166 6O :34.
TRACTOR -- MODEL NUMBER 917.272070 CHASSIS AND ENCLOSURES KEY PART NO. NO. DESCRIPTION 1 169830 Chassis 2 176554 Drawbar 3 17060612 Screw 3/8-16 x 3/4 5 155272 Bumper Hood/Dash 9 168337X013 Dash 10 STD533710 Bolt, Carriage 3/8-16 x 3/4 11 155927 Panel, Dash, L.
TRACTOR - - MODEL NUMBER 917.272070 GROUND DRIVE 197 21 10 14 16 _ ( - 169 164_44 18 32 30 166 156 5 18 62 35 37 34 • 22 I 26 27 11G • 150 / 48 36.
TRACTOR - - MODEL NUMBER 917.272070 GROUND DRIVE KEY PART KEY NO. NO. DESCRIPTION NO. 1 ........ Transaxle (See Breakdown) 63 Peedess 206-545C 64 2 146682 Spring, Return, Brake 65 3 123666X Pulley, Tr.
TRACTOR - - MODEL NUMBER 917.272070 STEERING ASSEMBLY _-- 38 _ 83 - .- • 4.- I' - 1 __,'i _1 _--42 38.
TRACTOR - - MODEL NUMBER 917.272070 STEERING ASSEMBLY KEY PART NO. NO. DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 13 15 17 18 19 22 23 25 26 27 28 29 3O 32 36 37 38 39 40 41 42 43 44 46 47 51 54 62 63 65 66 67 68 79 50 82 85 139768 SteerlngWheel 154427 Axle Asseml_y STMP Dropped STL 169840 Spindle Assembly, L.
ENGINE TRACTOR -- MODEL NUMBER 917.272070 32_._ i_- 44 _ _46 31 / _ 33 29 4o / OPTIONAL EQUIPMENT Spark Arrester 38 ! i 14 _105 8o_ 'i 4 i KEY PART NO. NO. DESCRIPTION 1 170548 Control, Throttle 2 17720410 Screw. Hex Head, Thread Cutting 1/4-20 x 5/6 3 .
TRACTOR - - MODEL NUMBER 917.272070 SEAT ASSEMBLY KEY PART NO. NO. DESCRIPTION KEY PART NO, NO, DESCRIPTION 1 140123 Seat 13 121248X 2 140551 Bracket Pnt Pivot Seat (blk) 14 72050412 3 71110616 Bolt F.
DECALS TRACTOR o - MODEL NUMBER 917.272070 13 13 63 11 11 10 2O 7 5 12 14 KEY PART NO. NO. 1 156368 2 171764 3 177333 4 177334 5 138047 6 133644 7 177367 8 172331 9 163204 10 156439 DESCRIPTION Decal. Oper, Instr. Decal, Replacemenl Decal, Hood, R.H.
TRACTOR - - MODEL NUMBER 917.272070 LIFT ASSEMBLY ,_ 7 3 I 6 # 5 4 20 " 1718 20 20 - ,1-_ _ 2o / 15 KEY PART NO. NO. DESCRIPTION 1 159460 Washer Asm inner Spring W/ Plunger 2 159471 Shaft Asm. Lift 3 108767X Pin Groove 4 12000(308 E Ring #5133-62 5 19211621 Washer 21/32 x 1 x 21 Ga.
TRACTOR -- MODEL NUMBER 917.272070 MOWER DECK 34 116 113 111 11 117 _ 1: 118 _ -130 5 6 19 21 I I 21 22 23 / 24 ,I !; 28 I' 117 _116 27 44.
TRACTOR - - MODEL NUMBER 917.272070 MOWER DECK KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. 1 165892 Mower Deck Assembly, 42" 67 149846 2 STD533107 Bolt 68 144959 3 138017 BracketAssembly,SwayBar.
TRACTOR - - MODEL NUMBER 917.272070 PEERLESS TRANSAXLE - - MODEL NUMBER 206-545C 47 6O 41A 7g 46.
TRACTOR - - MODEL NUMBER 917.272070 PEERLESS TRANSAXLE - - MODEL NUMBER 206-545C RFJ = PART REF PART NO, NO, DESCRIPTION NO. NO. DESCRIPTION 1 772147 Transaxle Cover 41A 790079 2 780086A Needle Searin.
TRACTOR -- MODEL NUMBER 917.272070 KOHLER ENGINE-MODEL NUMBER CV490, TYPE NUMBER 27505 CYLINDER HEAD, VALVE AND BREATHERI 21 24 /' 20 19 18 48.
TRACTOR - - MODEL NUMBER 917.272070 KOHLER ENGINE-MODEL NUMBER CV490, TYPE NUMBER 27505 CYLINDER HEAD/VALVE/BREATHER CRANKCASE KEY PART KEY PART NO. NO.
TRACTOR -- MODEL NUMBER 917.272070 KOHLER ENGINE-MODEL NUMBER CV490, TYPE NUMBER 27505 IGNITION/ELECTRICAL I BLOWER HOUSING AND BAFFLESI 0-8J- 4 5 5O.
TRACTOR - - MODEL NUMBER 917.272070 KOHLER ENGINE-MODEL NUMBER CV490, TYPE NUMBER 27505 IGNITION/ELECTRICAL BLOWER HOUSING & BAFFLES KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 2 3 4 5 6 7 8 9 10 11 12 13 14 15 12-086-14-S Screw, hex.
TRACTOR -- MODEL NUMBER 917.272070 KOHLER ENGINE-MODEL NUMBER CV490, TYPE NUMBER 27505 STARTING SYSTEM I I ENGINE CONTROLS I 1_ _ , "-,, ',, k_,kk k " t,J,_ _13 td_F_ _-_ I ' OIL P.
TRACTOR - - MODEL NUMBER 917.272070 KOHLER ENGINE-MODEL NUMBER CV490, TYPE NUMBER 27505 STARTING SYSTEM ENGINE CONTROLS KEY PART KEY PART NO. NO. DESCRIPTION NO.
TRACTOR - - MODEL NUMBER 917.272070 KOHLER ENGINE-MODEL NUMBER CV490, TYPE NUMBER 27505 CRANKSHAFTJ EXHAUST I 54.
TRACTOR - - MODEL NUMBER 917.272070 KOHLER ENGINE-MODEL NUMBER CV490, TYPE NUMBER 27505 FUEL SYSTEM NOT ILLUSTRATED *M-561010-S Screw, thread forming KEY PART MSx0.Bxl0 NO. NO. DESCRIPTION *X-22-11-S Washer, lock 1/4" 12_757oB2-S Kit, float 1 Mo641060-S Nut, hex.
56.
57.
58.
SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL Ln _0 1_ erate your Tractor up and down the face of slopes (not greater than 15°), never across the face. Make turns gradu- ally to prevent tipping or loss of control.
Get it fixed, at your home or ours! For repair of major brand appliances in your own home... no matter who made it, no matter who sold it! 1-800-4"MY'HOME s_ Anytime, day or night (1-800-469-4663) www.
Een belangrijk punt na aankoop van elk apparaat Craftsman 917.27207 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Craftsman 917.27207 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Craftsman 917.27207 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Craftsman 917.27207 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Craftsman 917.27207 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Craftsman 917.27207 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Craftsman 917.27207 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Craftsman 917.27207 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
