Gebruiksaanwijzing /service van het product CS-882 van de fabrikant Crimestopper Security Products
Ga naar pagina of 10
CS - 882 OEM ALARM UPGRADE FOR FACTORY KEYLESS ENTRY INSTALLATION & OPERATING INSTRUCTIONS INTRODUCTION CONGRATULATIONS on your choice of an Alarm Upgrade System by Crimestopper Security Products Inc. This booklet contains the information necessar y for installing, using, and maintaining this system.
COMPONENT MOUNTING Control Unit: DO NOT mount or wiring harness where they can become entangled with moving parts such as brake/gas/clutch pedals, or th e steering column! The control module should be mounted in a concealed location. Do not mount the control unit in the engine compartment.
WIRING ORANGE WIRE: ( - ) NEGATIVE STARTER DISABLE (Armed output) Ground output when system is armed. This output is used for disabling the starter or to activate other option al devices such as scanner LED’s, window control modules, voice modules etc.
WIRING GREEN WIRE: ( - ) HOOD/TRUNK TRIGGER Connect this wire to a grounding hood / trunk pin switch or to existing factory hood and trunk pin switches that read ground when open. If no existing switches are available, new pin switches may be installed.
4 ON CURRENT SENSING DIP SWITCH #4 OFF CURRENT SENSING The CS - 882OEM system includes a current sensing circuit to monitor current flow through the vehicles electrical system.
2 3 1 4 ON NEGATIVE VALIDATION INPUTS (TOP EDGE OF 882 MODULE) 2 3 1 4 ON POSITIVE VALIDATION INPUTS (TOP EDGE OF 882 MODULE) DOOR / LOCK & VALIDATION WIRES (TYPICAL INSTALLATION) VALIDATION WIRES.
PROGRAMMABLE OPTIONS 1. Turn the Ignition ON and press the Override/Program button 7 times within 10 seconds. 2. Turn OFF Ignition. LED will flash slowly once per second as and indicator the system is in programming mode. 3. Within 20 seconds, press the Override/Program button the number of times that corresponds to the feature list below.
OPERATION ARMING To arm the alarm and lock the doors, press the Lo ck button of your Factory Keyless Remote Control. The 882 OEM system will sense the Door Lock signal and Arm. The lights will flash once, the vehicle horn or siren will chirp once. After 3 seconds, the LED indicator will begin flashing slowly and Immobi lizer circuits become active.
OPERATION VALET MODE To disable alarm fun ctions of the 882 system, turn the Ignition ON and press the override/program button 3 times within 8 seconds. After 8 seconds, the dash LED turns on solid as an indicator that the system is in valet mode. Repeat this steps to exit VALET mode.
WIRING DIAGRAM VALET/ IGN SW. STARTER STATUS LED FUSE BOX IGNITION ON & CRANKING VOLTAGE STARTER WIRE 85 87A CUT 86 30 RED VIOLET BLACK WHITE/RED (-) ARMED OUTPUT (STARTER DISABLE) IGN SW.
Een belangrijk punt na aankoop van elk apparaat Crimestopper Security Products CS-882 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Crimestopper Security Products CS-882 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Crimestopper Security Products CS-882 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Crimestopper Security Products CS-882 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Crimestopper Security Products CS-882 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Crimestopper Security Products CS-882 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Crimestopper Security Products CS-882 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Crimestopper Security Products CS-882 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.