Gebruiksaanwijzing /service van het product KOR-61155 van de fabrikant Daewoo
Ga naar pagina of 30
Ser vice Manual Micr owave Oven KOR-6115 5 KOR-61151 DAEWOO ELECTRONICS CO., L TD..
2 PRECAUTIONS T O BE OBSERVED BEFORE AND DURING SERVICING T O A VOID POSSIBLE EXPOSURE T O EXCESSIVE MICROW A VE ENERGY (a) Do not operate or allow the oven to be operated with the door open.
3 PROPER USE AND SERVICE PRECAUTIONS CAUTION : THIS DEVICE IS TO BE SERVICED ONLY BY PROPERLY QUALIFIED SERVICE PERSONNEL. CONSULT THE SERVICE MANUAL FOR PROPER SERVICE PROCEDURES TO ASSURE CONTINUED SAFETY OPERATION AND FOR PRECAUTIONS TO BE TAKEN TO AVOID POSSIBLE EXPOSURE TO EXCESSIVE MICROWAVE ENERGY.
4 SPECIFICA TIONS ITEM SPECIFICATION POWER SUPPLY 120V~60Hz, SINGLE PHASE WITH EARTHING POWER CONSUMPTION 920 W MICROWAVE OUTPUT POWER 600 W (IEC 705) (FULL MICROWAVE POWER) FREQUENCY 2450 MHz OUTPUT DIMENSIONS (W X H X D) 465 X 274 X 360 mm (18.3 X 10.
¤ Safety Interlock System ¤Ł Door Viewing Screen - Allows viewing of food. The screen is designed so that light can pass through, but not the microwave. ¤Ø Door Hook - When the door is closed, it will automatically shut. If the door is opened while the oven is operating, the magnetron will immediately stop operating.
1 Steady , flat location This microwave oven should be set on a steady, flat surface. 2 Leave space behind and side All air vents should be kept a clearance. If all vents are covered during operation, the oven may overheat and, eventually, cause oven failure.
1 Connect the main lead to an electrical outlet. 2 After placing the food in a suitable container, open the oven door and put it on the glass tray. The glass tray must always be in place during cooking. 3 Close the door securely. 4 Choose cooking power by setting V.
Microwave output power can be checked by indirectly measuring the temperature rise of a certain amount of water exposed to the microwave as directed below.
W ARNING • Make sure to check the microwave leakage before and after repair of adjustment. • Always, start measuring of an unknown field to assure safety for operating personnel from microwave energy. • Do not place your hands into any suspected microwave radiation field unless the safe density level is known.
10 KOR-61 15 WIRING DIAGRAM POWER SUPPLY : PRIMARY INTERLOCK SWITCH(UPPER) TIMER SWITCH TIMER ASS'Y V.P.C . FUSE INTERLOCK MONITOR SWITCH HIGH VOLTAGE TRANSFORMER H.
11 KOR-61 151 WIRING DIAGRAM POWER SUPPLY : PRIMARY INTERLOCK SWITCH(UPPER) TIMER SWITCH TIMER ASS'Y V.P.C . CAVITY THERMOSTAT INTERLOCK MONITOR SWITCH HIGH VOLTAGE TRANSFORMER H.
1. When the food is placed in the oven cavity and door is closed. • The contact of the interlock monitor switch open. • The contacts of the primary interlock switch and secondary interlock switch close. 2. When the timer is set to the time desired.
13 HIGH VOLTAGE TRANSFORMER H.V. CAPACITOR H.V. FUSE H.V. DIODE Fig. 2 MAGNETRON 3. When the door is opened during cooking. • Primary interlock switch and secondary interlock switch open to cut off the primary voltage to the high voltage transformer to stop microwave oscillation.
ƒ¡ Cautions to be observed when trouble shooting. Unlike many other appliances, the microwave oven is a high-voltage, high-current equipment. It is completely safety during normal operation. However, carelessness in servicing the oven can result in an electric shock or possible danger from a short circuit.
15 DISASSEMBL Y AND ASSEMBL Y 1. T o remove cabinet Remove three screws on cabinet back. 2. T o remove door assembly (1) Remove two screws ¤ which secure the stopper hinge top. (2) Remove the door assembly ¤Ø from top plate of cavity. (3) Remove the above for reassembly.
16 (1) Remove the gasket door ¤ from door plate ¤Œ . (2) Remove the barrier screen inner ¤º from door plate ¤Œ . (3) Remove the door frame ¤Ł from door plate ¤Œ . (4) Remove the stopper hinge top ¤Ø from door plate ¤Œ . (5) Remove the spring ¤ and the hook ¤ .
17 5. T o remove control panel parts (1) Remove the screw which secure the control panel, push up two snap fits and draw forward the control panel assembly. (2) Remove the door open lever ¤ from the control panel. (3) Remove two screws ¤Ł which secure the timer assembly ¤Ø .
6. T o remove high voltage capacitor (1) Remove a screw ¤ which secure the grounding ring ring terminal of the H.V. diode ¤Ł and the capacitor holder ¤Ø . (2) Remove the H.V. diode ¤Ł from the capacitor ¤Ø . (4) Reverse the above steps for reassembly.
19 8. T o remove fan motor assembly (1) Remove two screws ¤ which secure the back cover ¤Ł from the cavity outer . (2) Remove two screws ¤Ø which secure the fan motor ¤Œ from the back cover ¤Ł . (3) Pull out the fan ¤º from the fan motor ¤Œ .
20 The door lock mechanism is a device which has been specially designed to completely eliminate microwave radiation when the door is opened during operation, and thus to perfectly prevent the danger resulting from the leakage of microwave. (1) Primary interlock switch When the door is closed, the hook locks the oven door.
21 (2) Secondary interlock switch and interlock monitor switch When the door is closed, the hook pushes the push lever downward, the push lever presses the button of the interlock monitor switch to bring it under “OFF”, condition and presses the button of the secondary interlock switch to bring it under “ON”, condition.
22 TROUBLE SHOOTING GUIDE TROUBLE DOOR SHUT, TIMER SET BUT NO COOKING TAKES PLACE. Does the fan motor work when you shut the door and turn the timer? Does 15A fuse blow? Check continuity of inter- lock monitor switch with door shuted.
23 Does the fan motor when you shut the door and turn the time? No microwave oscillation. Check continuity of filament of magnetron. NO NO continuity Replace or repair oven lamp, turntable motor. Replace magnetron. Replace high voltage transformer. Replace high voltage diode.
24 1. High voltage is present at the high voltage terminal of the voltage transformer during any cooking cycle. 2. It is neither necessary nor advisable to attempt measurement of the high voltage. 3. Before touching any oven components or wiring, always unplug the oven from its power source and discharge the capacitor (see page 13).
6. Interlock switches • You can test continuity of safety interlocks and monitor switch by using switch tester or ohmmeter. • The switch operation is checked by zero/unlimited. the meter should indicate zero resistance. • The sequence of check is interlock monitor switch; primary and secondary interlock switched check.
26 NO PART NAME PARTS CODE Q’TY A01 BARRIER-SCREEN *O 3517003000 1 A02 FRAME DOOR 3512202500 1 A03 STOPPER HINGE *T 3515201000 1 A04 DOOR WELD AS 3511705500 1 A05 BARRIER-SCREEN *I 3517002800 1 A06 GASKET DOOR 3512300200 1 A07 HOOK 3513100700 1 A08 SPRING HOOK 3515101300 1 1.
27 2. Control Panel Ass’y NO PART NAME PARTS CODE Q’TY B01 KNOB VPC 3513402600 1 B02 CONTROL PANEL 3512202000 1 B03 COUPLER VPC KNOB 3517400500 1 B04 SCREW TAPPINGT2S PAN 4X12 PW 7621401211 1 B05 .
REE NO. PART CODE PART NAME DESCRIPTION Q’TY REMARKS A00 3511706010 DOOR AS KOR-61150S 1 B00 3516713100 CONTROL-PANEL AS KOR-61150A 1 F01 3510801300 CABINET PCM T0.
31 KOR-61 151 Parts List REE NO. PART CODE PART NAME DESCRIPTION Q’TY REMARKS A00 3511706010 DOOR AS KOR-61150S 1 B00 3516713100 CONTROL-PANEL AS KOR-61150A 1 F01 3510801300 CABINET PCM TO.
DAEWOO ELECTRONICS CO., L TD. 686, AHYEON-DONG, MAPO-GU, SEOUL, KOREA C.P.O. BOX 8003 SEOUL, KOREA TELEX: DWELEC K28177-8 CABLE: “DAEWOOELEC” FAX: 02) 364-5588/5305 TEL: 02) 360-7114/7315~7 PRINTED DA TE: MAR.
Een belangrijk punt na aankoop van elk apparaat Daewoo KOR-61155 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Daewoo KOR-61155 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Daewoo KOR-61155 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Daewoo KOR-61155 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Daewoo KOR-61155 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Daewoo KOR-61155 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Daewoo KOR-61155 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Daewoo KOR-61155 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
