Gebruiksaanwijzing /service van het product KOR-6Q2B5S van de fabrikant Daewoo
Ga naar pagina of 33
Ser vice Manual Micr owave Oven Model: KOR-6Q2B5S DAEWOO ELECTRONICS CORP . S/M No. : R6Q2B5S001 http : //svc.dwe.co.kr Jul. 2004 ✔ Caution : In this Manual, some parts can be changed for improving, their performance without notice in the parts list.
1 PRECAUTIONS T O BE OBSERVED BEFORE AND DURING SERVICING T O A VOID POSSIBLE EXPOSURE T O EXCESSIVE MICROW A VE ENERGY (a) Do not operate or allow the oven to be operated with the door open.
2 SAFETY AND PRECAUTIONS 1. FOR SAFE OPERA TION Damage that allows the microwave energy (that cooks or heats the food) to escape will result in poor cooking and may cause serious bodily injury to the operator. IF ANY OF THE FOLLOWING CONDITIONS EXIST, OPERATOR MUST NOT USE THE APPLIANCE.
3 MODEL KOR-6Q2B5S POWER SUPPLY 230V-50Hz, SINGLE PHASE WITH EARTHING MICROWAVE 1200W POWER CONSUMPTION GRILL COMBINATION MICROWAVE ENERGY OUTPUT 800W MICROWAVE FREQUENCY 2450MHz OUTSIDE DIMENSIONS (W X H X D) 465 x 279 x 327 mm (18.3 x 11.0 x 12.9 in) CAVITY DIMENSIONS (W X H X D) 301 x 230 x 283 mm (11.
4 EXTERNAL VIEW 1. OUTER DIMENSION.
5 1 1 DOOR SEAL - Door seal maintains the microwave within the oven cavity and prevents microwave leakage. 2 2 DOOR HOOK - When the door is closed, it will automatically lock shut. If door is opened while oven is operating, mag- netron tube will immediately stop operating.
6 1 8 4 0 q 2 9 3 6 5 7 1 1 Display - Cooking time, power level, indicators and the present time are displayed. 2 2 Power - Used to set power level. 3 3 Defrost - Used to defrost foods for time. 4 4 Clock - Used to set clock. 5 5 Up - Used to add time to cooking.
7 1. Steady, flat location This microwave oven should be set on a steady, flat surface. This microwave oven is designed for counter top use only. 2. Leave space behind and side All air vents should be kept a clearance. If all vents are covered during operation, the oven may overheat and, eventually, cause failure.
8 Make sure the oven is properly installed and plugged into the electrical. OPERA TIONS AND FUNCTIONS 1. Connect the main lead to an electrical outlet. 2. After placing the food in a suitable container, open the oven door and put it on the glass tray.
9 DISASSEMBL Y AND ASSEMBL Y Cautions to be observed when troubleshooting. Unlike many other appliances, the microwave oven is high-voltage, high-current equipment. It is completely safe during normal operation. However, carelessness in servicing the oven can result in an electric shock or possible danger from a short circuit.
10 1. T o remove cabinet 1) Remove three screws on cabinet back. 2) Pull the cabinet backward. 2. T o remove door assembly 1) Remove the screw which secure the stopper hinge top. 2) Remove the door assembly from top plate of cavity. 3) Reverse the above for reassembly.
11 3. T o remove door parts. REF NO. PART CODE PART NAME DESCRIPTION Q’TY REMARK A01 3512206440 FRAME DOOR HIPS 1 A02 3517007300 BARRIER-SCREEN*0 PET T0.125 1 A03 3515204100 STOPPER SINGE *T AS KOR-63150S 1 A04 3511719500 DOOR PAINTING AS KOR-6C0B5S 1 A05 3517002800 BARRIER-SCREEN *I T0.
12 4. Method to reduce the gap between the door seal and the oven front surface. (1) To reduce gap located on part ‘ A ’ Loosen the screw on stopper hinge top, and then push the door to contact the door seal to oven front surface. Tighten a screw.
13 5. T o remove control panel parts. REF NO. PART CODE PART NAME DESCRIPTION Q’TY REMARK B01 3518524120 SWITCH MEMBRANE KOR-6C2B5S 1 B02 3516730720 CONTROL PANEL HIPS 1 B03 PKMPMSBA00 PCB AS 6N(800.
14 6. T o remove high voltage capacitor . 1) Remove a screw which secure the grounding ring terminal of the H.V. diode and the capacitor holder. 2) Remove the H.V. diode from the capacitor holder. 3) Reverse the above steps for reassembly. ◆ High voltage circuit wiring 7.
15 8. T o remove wind guide assembly . 1) Remove a screw for earthing. 2) Remove the noise filter from the wind guide. 3) Remove a screw which secure the wind guide assembly. 4) Draw forward the wind guide assembly. 5) Pull the fan from the motor shaft.
16 INTERLOCK MECHANISM AND ADJUSTMENT The door lock mechanism is a device which has been specially designed to completely eliminate microwave radiation when the door is opened during operation, and thus to perfectly prevent the danger resulting from the leakage of microwave.
17 (TROUBLE 1) Oven does not operate at all ; any inputs can not be accepted. TROUBLESHOOTING GUIDE Following the procedure below to check if the oven is defective or not. 1. Check grounding before trouble checking. 2. Be careful of the high voltage circuit.
18 CONDITION CHECK Check continuity of primary inter- lock switch Malfunction of pri- mary interlock switch RESULT No Continuity CAUSE REMEDY Adjust or replace Turn table motor and oven lamp do not turn on Check continuity of secondary interlock switch Malfunction of sec- ondary interlock switch No Continuity Adjust or replace Check D.
19 (TROUBLE 3) No microwave oscillation even though fan motor rotates. CONDITION CHECK RESULT Check continuity of high voltage capacitor terminals with wires removed Continuity CAUSE Defective high vo.
20 (TROUBLE 4) The following visual conditions indicate a probable defective touch control circuit or membrane switch assembly. 1 1. Incomplete segments (1) Segments missing (2) Partical segments missing (3) Digit flickering other than normal display slight flickering (4) :0 does not display when power is on.
21 MEASUREMENT AND TEST 1. MEASUREMENT OF THE MICROW A VE POWER OUTPUT Microwave output power can be checked by indirectly measuring the temperature rise of a certain amount of water exposed to the microwave as directed below.
22 2. MICROW A VE RADIA TION TEST PROCEDURES 1 . Prepare Microwave Energy Survey Meter, 600cc glass beaker, and glass thermometer 100 ˚ C(212 ˚ F). 2. Pour 275cc±15cc of tap water initially at 20 ± 5 ˚ C(68±9 ˚ F) in the 600cc glass beaker with an inside diameter of approx.
23 3. COMPONENT TEST PROCEDURE • High voltage is present at the high voltage terminal of the high voltage transformer during any cooking cycle. • It is neither necessary nor advisable to attempt measurement of the high voltage.
24 WIRING DIAGRAM.
1. CIRCUIT CHECK PROCEDURE 1. Low V oltage Transformer check The low voltage transformer is located on the P.C.B. Measuring condition: input voltage : 230V/Frequency : 50Hz 2.
26 Measure Point MP1 MP1 GND.
3. When there is no microwave oscillation 1) When touching START pad, oven lamp does not turn on. Fan motor does not rotate, but cook indicator in display comes on. - Check method 2) When touching START pad, oven lamp turns on. Fan motor and turntable rotate and cook indicator in display comes on.
28 2. PCB CIRCUIT DIAGRAM.
29 NO NAME SYMBOL SPECIFICATION PART CODE Q ’ TY 1 BUZZER BZ1 BM-20K 3515600100 1 2 C ARRAY CA1 7P(6) 1000PF M 50V CN6XB-102M 1 3 CAPACITOR ELEC EC1 50V RS 10UF CEXE1H100A 1 4 CAPACITOR ELEC EC2 25V.
30 1. DOOR ASSEMBL Y Refer to Disassembly and assembly . 2. CONTROL P ANEL ASSEMBL Y Refer to Disassembly and assembly . 3. TOT AL ASSEMBL Y EXPLODED VIEW AND P AR TS LIST.
31 ✔ Caution : In this Manual, some parts can be changed for improving, their performance without notice in the parts list. So, if you need the latest parts information, please refer to PPL(Parts Price List) in Service Information Center (http://svc.
S/M NO. : R6Q2B5S001 DAEWOO ELECTRONICS CORP . 686, AHYEON-DONG MAPO-GU SEOUL, KOREA C.P.O. BOX 8003 SEOUL, KOREA TELEX: DWELEC K28177-8 CABLE: “DAEWOOELEC” PRINTED DA TE: Jul.
Een belangrijk punt na aankoop van elk apparaat Daewoo KOR-6Q2B5S (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Daewoo KOR-6Q2B5S heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Daewoo KOR-6Q2B5S vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Daewoo KOR-6Q2B5S leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Daewoo KOR-6Q2B5S krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Daewoo KOR-6Q2B5S bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Daewoo KOR-6Q2B5S kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Daewoo KOR-6Q2B5S . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
