Gebruiksaanwijzing /service van het product D15M van de fabrikant Dell
Ga naar pagina of 59
Dell OptiPlex 3020–Mini Tower Owner's Manual Regulatory Model: D15M Regulatory Type: D15M001.
Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death.
Contents 1 Working on Your Computer ................................................................................. 5 Before Working Inside Your Computer .............................................................................................5 Turning Off Your Computer .
Removing the I/O Panel .................................................................................................................. 25 Installing the I/O Panel .....................................................................................
1 Working on Your Computer Before Working Inside Your Computer Use the following safety guidelines to help protect your computer from potential damage and to help to ensure your personal safety.
3. Disconnect all network cables from the computer. 4. Disconnect your computer and all attached devices from their electrical outlets. 5. Press and hold the power button while the computer is unplugged to ground the system board. 6. Remove the cover.
CAUTION: To connect a network cable, first plug the cable into the network device and then plug it into the computer. 2. Connect any telephone or network cables to your computer. 3. Connect your computer and all attached devices to their electrical outlets.
8.
2 Removing and Installing Components This section provides detailed information on how to remove or install the components from your computer. Recommended Tools The procedures in this document may req.
5. front bezel 6. speaker 1. memory module 2. system board 3. optical drive 4. front i/o panel 5. coin cell 6. CPU cooler 7. system fan Removing the Cover 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove the thumbscrews that secure the cover to the computer.
3. Lift the cover upward to a 45–degree angle and remove it from the computer. Installing the Cover 1. Place the cover on the computer. 2. Slide the computer cover towards the front of the chassis until it is fully engaged. 3. Tighten the thumbscrew in clockwise direction to secure the computer cover.
Removing the Intrusion Switch 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove the: a) cover b) heatsink assembly 3. Perform the following steps as shown in the illustration: a) Press the intrusion-switch cable [1]. b) Disconnect the intrusion-switch cable from the system board [2].
Installing the Front Bezel 1. Insert the hooks along the bottom edge of the front bezel into the slots on the chassis front. 2. Push the bezel toward the computer to engage the front bezel retention clips until they click into place. 3. Install the cover.
4. Perform the following steps as shown in the illustration: a) Pull the release lever away from the expansion card until you release the securing tab from the dent in the card. [1]. b) Ease the card up and out of its connector and remove it from the computer.
Memory Module Guidelines To ensure optimal performance of your computer, observe the following general guidelines when configuring your system memory: • Memory modules of different sizes can be mixed (for example, 2 GB and 4 GB). But, all populated channels must have identical configurations.
Removing the Coin-Cell Battery 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove: a) cover b) expansion card(s) 3. Press the release latch away from the battery to allow the battery to pop-up from the socket and lift the coin-cell battery out of the computer.
4. Flex the hard-drive bracket and remove the hard drive from the hard-drive bracket. Installing the Hard Drive 1. Insert the hard drive into the hard-drive bracket. 2. Press the securing brackets inward and slide the hard-drive bracket into the bay. 3.
4. Repeat steps 3 remove the second optical drive (if available). Installing the Optical Drive 1. Push the optical drive from the front toward the back of the computer till it is secured by the optical-drive latch. 2. Connect the data cable and power cable to the back of the optical drive.
Installing the Speaker 1. Slide the speaker downwards into its slot to secure it. 2. Thread the speaker cable into the chassis clip and connect the speaker cable to the system board. 3. Install the cover. 4. Follow the procedures in After Working Inside Your Computer .
4. Remove the screws that secure the power supply to the back of the computer. 5. Perform the following steps as shown in the illustration: a) Push in on the blue release tab beside the power supply [1]. b) Slide the power supply towards the front of the computer [2].
Installing the Power Supply 1. Place the power supply in the chassis and slide towards the back of the system to secure it. 2. Tighten the screws to secure the power supply to the back of the computer. 3. Connect the 4-pin and 8-pin power cables to the system board.
Installing the Processor 1. Insert the processor in the processor socket. Ensure the processor is properly seated. 2. Lower the processor cover. 3. Press the release lever down and then move it inward to secure it with the retention hook. 4. Install: a) heat-sink assembly b) cover 5.
Installing the System Fan 1. Place the system fan in the chassis. 2. Pass the four grommets through the chassis and slide outward along the groove to secure in place. 3. Connect the system-fan cable to the system board. 4. Install the cover. 5. Follow the procedures in After Working Inside Your Computer .
4. Release the power-switch cable from the chassis clips. 5. Perform the following steps as shown in the illustration: a) Press the clips on both side of the power switch to release it from the chassis [1]. b) Slide to remove the power switch along its cable from the computer [2].
Installing the Power Switch 1. Slide the power switch in through the front of the computer. 2. Secure the power-switch cable to the chassis. 3. Thread the power-switch cable into the chassis clips. 4. Connect the power-switch cable to the system board.
4. Unthread and release the I/O Panel, data cable and USB data cable from the clip on the computer. 5. Remove the screw that secures the I/O panel to the computer.
6. Release and pull the I/O panel along with its cable out of the computer. Installing the I/O Panel 1. Insert the I/O panel into the slot on the chassis front. 2. Slide the I/O panel towards the right of the computer to secure to the chassis. 3. Tighten the screw to secure the I/O panel to the chassis.
7. Follow the procedures in After Working Inside Your Computer . System Board Components The following image displays the system board layout. 1. SATA connectors 2. password reset jumper 3. front USB2.0 connector 4. internal USB connector 5. RTCRST reset jump 6.
Removing the System Board 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove the: a) cover b) memory c) expansion card(s) d) heatsink assembly e) processor 3. Disconnect all the cables connected to the system board. 4. Perform the following steps as shown in the illustration: a) Disconnect the 8–pin power cable.
6. Tilt the system board at 45–degrees, and then lift the system board out of the computer. 7. Lift the system board out of the computer. 30.
Installing the System Board 1. Align the system board to the port connectors on the rear of the chassis and place the system board in the chassis. 2. Tighten the screws that secure the system board to the chassis. 3. Connect the cables to the system board.
32.
3 System Setup System Setup enables you to manage your computer hardware and specify BIOS ‐ level options. From the System Setup, you can: • Change the NVRAM settings after you add or remove hardw.
Table 1. Navigation Keys Keys Navigation Up arrow Moves to the previous field. Down arrow Moves to the next field. <Enter> Allows you to select a value in the selected field (if applicable) or follow the link in the field. Spacebar Expands or collapses a drop ‐ down list, if applicable.
Option Description – UEFI Advanced Boot Options Allows you to Enable Legacy Option ROMs • Enabled (Default) Date/Time Allows you to set the date and time. The changes to the system date and time takes effect immediately. Table 3. System Configuration Option Description Integrated NIC Allows you to configure the integrated network controller.
Option Description part of the SMART (Self Monitoring Analysis and Reporting Technology) specification. • Enable SMART Reporting - This option is disabled by default. USB Configuration Allows you to enable or disable the internal USB configuration. The options are: • Enable Boot Support • Enable Front USB Ports • Enable USB 3.
Option Description • Enter the new password • Confirm the new password Strong Password Enable strong password - This option is disabled by default. Password Configuration This field controls the minimum and maximum number of characters allowed for the admin and system passwords.
Option Description • Enable CPU XD Support - This option is enabled by default. Admin Setup Lockout Allows you to enable or disable the option to enter setup when an admin password is set. • Enable Admin Setup Lockout - This option is not set by default.
Table 7. Performance Option Description Multi Core Support Specifies whether the process will have one or all cores enabled. The performance of some applications will improve with the additional cores. • All - Enabled by default • 1 • 2 Intel SpeedStep Allows you to enable or disable the Intel SpeedStep feature.
Option Description • Enabled in S5 only • Enabled in S4 and S5 Enabled Fan Speed Control Controls the speed of the system fan. This option is disabled by default. NOTE: When enabled, the fan runs at full speed. USB Wake Support This option allows you to enable USB devices to wake the computer from standby.
Table 11. Maintenance Option Description Service Tag Displays the service tag of your computer. Asset Tag Allows you to create a system asset tag if an asset tag is not already set. This option is not set by default. SERR Messages Controls the SERR message mechanism.
Option Description NOTE: This field is only relevant when the Integrated NIC control in the System Configuration group is set to Enabled with ImageServer and when Client DHCP is set to Static IP .
Clearing Forgotten Password The system's software security features include a system password and a setup password. The password jumper disables any password(s) currently in use. There are 3–pins for the password reset jumper. 1. Follow the procedures in Before Working Inside Your Computer .
CAUTION: The password features provide a basic level of security for the data on your computer. CAUTION: Anyone can access the data stored on your computer if it is not locked and left unattended. NOTE: Your computer is shipped with the system and setup password feature disabled.
4. Select Setup Password , alter or delete the existing setup password and press <Enter> or <Tab>. NOTE: If you change the System and/or Setup password, re-enter the new password when promoted. If you delete the System and/or Setup password, confirm the deletion when promoted.
46.
4 Diagnostics If you experience a problem with your computer, run the ePSA diagnostics before contacting Dell for technical assistance. The purpose of running diagnostics is to test your computer's hardware without requiring additional equipment or risking data loss.
48.
5 Troubleshooting Your Computer You can troubleshoot your computer using indicators like Diagnostic Lights, Beep Codes, and Error Messages during the operation of the computer. Power LED Diagnostics The power button LED located on the front of the chassis also functions as a bicolored diagnostic LED.
Amber LED State Description 3,6 possible system board resource and/or hardware failure 3,7 some other failure with messages on screen Beep Code The computer can emit a series of beeps during start-up if the display does not show errors or problems. These series of beeps, called beep codes, identify various problems.
Error Message Description Bad command or file name Ensure that you have spelled the command correctly, put spaces in the proper place, and used the correct pathname. Bad error- correction code (ECC) on disk read The floppy or hard drive controller detected an uncorrectable read error.
Error Message Description please populate DIMM1 Keyboard failure A cable or connector may be loose, or the keyboard or keyboard/mouse controller may be faulty. Memory address line failure at address, read value expecting value A memory module may be faulty or improperly seated.
Error Message Description Non-system disk or disk error The floppy disk in drive A does not have a bootable operating system installed on it. Either replace the floppy disk with one that has a bootable operating system, or remove the floppy disk from drive A and restart the computer.
Error Message Description drive by calling your support desk or Dell. Write fault The operating system cannot write to the floppy or hard drive. Write fault on selected drive The operating system cannot write to the floppy or hard drive.
6 Technical Specifications NOTE: Offerings may vary by region. The following specifications are only those required by law to ship with your computer. For comprehensive specification of your computer go to Specifications’ section in your Owner’s Manual available on the support site at dell.
Feature Specification Volume controls volume up/down buttons, program menus, and keyboard media-control keys Table 19. Communications Feature Specification Network adapter Intel 10/100/1000 Mbps Ethernet LAN on system board Table 20.
Feature Specification Off (no light) — the computer is not detecting a physical connection to the network. Network activity light on integrated network adapter Yellow light — A blinking yellow light indicates that network activity is present. Power supply diagnostic light Green light — The power supply is turned on and is functional.
Feature Specification Altitude: Operating –15.2 m to 3048 m (–50 to 10,000 ft) Storage –15.20 m to 10,668 m (–50 ft to 35,000 ft) Airborne contaminant level G1 or lower as defined by ANSI/ISA-S71.
7 Contacting Dell NOTE: If you do not have an active Internet connection, you can find contact information on your purchase invoice, packing slip, bill, or Dell product catalog. Dell provides several online and telephone-based support and service options.
Een belangrijk punt na aankoop van elk apparaat Dell D15M (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Dell D15M heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Dell D15M vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Dell D15M leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Dell D15M krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Dell D15M bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Dell D15M kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Dell D15M . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
