Gebruiksaanwijzing /service van het product ST2E van de fabrikant Dell
Ga naar pagina of 37
Dell Latitude 10 – ST2e Owner's Manual Regulatory Model: T05G Regulatory Type: T05G001.
Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death.
Contents Notes, Cautions, and Warnings ...................................................................................................2 1 Working on Your Computer ....................................................................................
Running the ePSA Diagnostic Utility .......................................................................................................................27 Beep Codes ..................................................................................
1 Working on Your Computer Before Working Inside Your Computer Use the following safety guidelines to help protect your computer from potential damage and to help to ensure your personal safety.
NOTE: To avoid damaging the system board, you must remove the main battery before you service the computer. 7. Remove the main battery. 8. Turn the computer top-side up. 9. Press the power button to ground the system board. CAUTION: To guard against electrical shock, always unplug your computer from the electrical outlet before opening the display.
NOTE: It is recommended that you immediately backup the operating system image using the USB device through Dell Backup and Recovery (DBAR) application.
8.
2 Removing and Installing Components This section provides detailed information on how to remove or install the components from your computer. Recommended Tools The procedures in this document may req.
5. volume button 6. speaker 7. battery 8. docking board 9. coin-cell battery 10. speaker Removing the Base Cover 1. Follow the procedures in Before Working Inside Your Computer . 2. Pry and lift the base cover from the computer by following the arrow sequence in the diagram.
Installing the Battery 1. Tighten the screws to secure the battery to the computer. 2. Install the base cover. 3. Follow the procedures in After Working Inside Your Computer. Removing the Front Camera 1. Follow the procedures in Before Working Inside Your Computer .
Installing the Front Camera 1. Place the camera module in its slot on the computer. 2. Tighten the screw to secure the camera module to the computer. 3. Connect the camera cable to the connector. 4. Install the: a) battery b) base cover 5. Follow the procedures in After Working Inside Your Computer .
5. Un-route the speaker cable on the side of the computer and lift it up to release the speaker from the computer. 6. Un-route the speaker cable on the side of the computer and lift it up to release the speaker from the computer.
Installing the Speakers 1. Place the right and the left speakers in their slot. 2. Route the speaker cables on the chassis. 3. Tighten the screws to secure the speakers to the chassis. 4. Place the coin-cell battery in its slot and route the cables. 5.
4. Remove the screws that secure the docking board to the computer. 5. Remove the docking board from the computer and disconnect the home-button board cable. Installing the Docking Board 1. Connect the home-button board cable to the docking board and place the docking board in its slot in the computer.
Removing the System Board 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove the: a) base cover b) battery c) speaker d) front camera e) docking board 3. Disconnect the LVDS and docking board cables. 4. Remove the screws that secure the system board to the computer.
4. Install the: a) docking board b) front camera c) speaker d) battery e) base cover 5. Follow the procedures in After Working Inside Your Computer . Removing the Rear Camera 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove the: a) base cover b) battery c) speaker d) front camera e) system board 3.
Removing the Coin-Cell Battery 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove the: a) base cover b) battery c) speaker d) front camera e) system board 3. Disconnect the coin-cell battery cable and remove it from the computer.
b) battery 3. Disconnect the volume-board cable from the connector. Lift up and remove the volume-board cable from the system board. 4. Pry the sides of the volume-button board with a flat-head screw driver to loosen it from it's slot on the computer.
20.
3 System Setup System Setup enables you to manage your computer hardware and specify BIOS ‐ level options. From the System Setup, you can: • Change the NVRAM settings after you add or remove hardw.
Keystroke Action connected to an optional external USB keyboard) On Screen Mouse Pointer Use this to navigate the System Setup by using your finger or an interactive pen. Apply Icon Save current configuration. Defaults Icon Load setup defaults. Exit Icon Exits System Setup.
Table 3. Boot Sequence Option Function File Browser Add Boot Option Displays the order that the BIOS searches devices when trying to find an operating system to boot. A new device can be added here. File Browser Del Boot Option A displayed boot device can be removed from the boot order.
Option Description Click OK after entering the password details. System Password Allows you to set, change, or delete the computer password (previously called the primary password).
Option Description Admin Setup Lockout Allows you to enable or disable the option to enter setup when an admin password is set. • Enable Admin Setup Lockout (Default) Table 8. Secure Boot Option Function Secure Boot Enables or Disables the secure boot feature.
Option Description • Disabled - Does not allow the system to power on by special LAN signals when it receives a wake-up signal from the LAN or wireless LAN. (Default ) • LAN Only - Allows the system to be powered on by special LAN signals. Table 11.
4 Troubleshooting Your Computer You can troubleshoot your computer using indicators like Diagnostic Lights, Beep Codes, and Error Messages during the operation of the computer. Enhanced Pre-boot System Assessment (ePSA) The ePSA is a diagnostic utility available on your computer.
2. The computer will start up and begin running the ePSA utility automatically. 3. During the testing process, you will be prompted to answer a YES or NO question.
4. Press the Security Button (<Ctrl> + <Alt> + <Del>) to click OK once the tests are completed. 5. The volume up and down buttons can also be used as the <Tab> key when switching between options. Beep Codes The computer may emit a series of beeps during start-up if the display cannot show errors or problems.
Code Cause and Troubleshooting Steps System board failure, covers BIOS corruption or ROM error 2 No RAM detected No memory detected 3 Chipset Error (North and South Bridge Chipset, DMA/IMR/ Timer Erro.
Code Cause and Troubleshooting Steps 6 Video BIOS test failure Video card failure 7 CPU - cache test failure Processor failure 8 Display Display failure 31.
32.
5 Specifications Specifications NOTE: Offerings may vary by region. The following specifications are only those required by law to ship with your computer. For more information regarding the configuration of your computer, click Start → Help and Support and select the option to view information about your computer.
Video Video type integrated Data bus internal Video controller Intel Graphics Media Accelerator Communications Network adapter USB 2.0 based Gigabit LAN via dock Ports and Connectors Audio one microphone-in and stereo headphones/speakers combo connector Video one mini HDMI connector USB one USB 2.
Battery Width 86.50 mm (3.40 inches) Weight 220.00 g (0.49 lb) Voltage 7.4 VDC Temperature range Operating 0 °C to 50 °C (32° F to 158 °F) Non-Operating -20 °C to 65 °C ( –4 °F to 149 °F) Coin-cell battery 3 V CR2025 lithium ion AC Adapter Type Input voltage 100 VAC to 240 VAC Input current (maximum) 0.
Environmental Operating –16 m to 3048 m (–50 to 10,000 ft) Non-operating –15.2 m to 10,668 m (–50 ft to 35,000 ft) Airborne contaminant level G1 as defined by ISA-71.
6 Contacting Dell Contacting Dell NOTE: If you do not have an active Internet connection, you can find contact information on your purchase invoice, packing slip, bill, or Dell product catalog. Dell provides several online and telephone-based support and service options.
Een belangrijk punt na aankoop van elk apparaat Dell ST2E (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Dell ST2E heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Dell ST2E vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Dell ST2E leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Dell ST2E krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Dell ST2E bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Dell ST2E kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Dell ST2E . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
