Gebruiksaanwijzing /service van het product 36-865 van de fabrikant Delta
Ga naar pagina of 20
INSTRUCTION MANUAL P ART NO. 1348009 - 03-31-05 Copyright © 2005 Delta Machinery VERSA-FEEDER TM (Model 36-865) Stock Feeder T o learn more about DEL T A MACHINER Y visit our website at: www .deltamachinery .com. For Parts, Service, W arranty or other Assistance, please call 1-800-223-7278 ( In Canada call 1-800-463-3582).
2 T ABLE OF CONTENTS Read and understand all warnings and operating instructions before using any tool or equipment. When using tools or equipment, basic safety precautions should always be followed to r educe the risk of personal injury .
3 Indicates an imminently hazardous situation which, if not avoided, will r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, could r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, may r esult in minor or moderate injury .
4 GENERAL SAFETY RULES READ AND UNDERST AND ALL W ARNINGS AND OPERA TING INSTRUCTIONS BEFORE USING THIS EQUIPMENT . Failure to follow all instructions listed below , may result in electric shock, fire, and/or serious personal injury or pr operty damage.
5 F AILURE TO FOLLOW THESE RULES MA Y RESUL T IN SERIOUS PERSONAL INJUR Y . ADDITIONAL SPECIFIC SAFETY RULES SA VE THESE INSTRUCTIONS. Refer to them often and use them to instruct others. 1. DO NOT OPERA TE THIS MACHINE until it is completely assembled and installed according to the instructions.
6 A separate electrical circuit should be used for your machines. This cir cuit should not be less than #12 wire and should be protected with a 20 Amp time lag fuse. If an extension cor d is used, use only 3-wire extension cor ds which have 3- prong gr ounding type plugs and matching receptacle which will accept the machine’ s plug.
7 FOREWORD Delta Model 36-865 V ersa-Feeder Stock Feeder (V ariable Speed) includes a 1/8 hp 120V reversing motor . This model comes with three rubber feed r ollers, a vertical and horizontal adjustable support arm, and a base mounting bracket. FUNCTIONAL DESCRIPTION EXTENSION CORDS Use proper extension cor ds.
8 1. Stock Feeder 2. Overarm 3. Overarm Clamp Assembly 4. Swivel Joint 5. Base 6. Pivot Ball 7. Shaft 8. 14MM and 17MM Open-end W rench 9. T -Handle Screw 10. Locking Lever 11. M8 Flat Washer 12. M8 Hex Nut 13. 3/8 Lockwasher 14. 3/8-16 x 1" Hex Socket Head Screw 15.
9 ASSEMBL Y ASSEMBL Y TOOLS REQUIRED ASSEMBL Y TIME ESTIMA TE 3/8" Wr ench 5/16" Wr ench 7/16" Wr ench 1/2" Wr ench 4mm Hex Wr ench Phillips Screwdriver Approximately 2-4 hours The V ersa-Feeder TM can be assembled as shown in Figs.
10 2. Place the pivot ball housing (F) Fig. 7 in the sleeve (G) of stock feeder . NOTE: Position the slot in the pivot ball housing (F) "up" (Fig. 8). 3. Insert the overarm (B) Fig. 9 with pivot ball (A) attached, thr ough the housing (F) until the pivot ball (A) is inside the housing (F).
11 5. Insert the metal shaft (J) Fig. 12 through the hole in the side of the sleeve (G) and into the wide slots of the pivot cover (H ) Fig. 12. Thread the T -handle screw (K) Fig. 13 into the hole of the shaft (J), just enough to hold the pivot pin assembly in position.
12 9. Insert the end of the overarm assembly (B) Fig. 18 into the clamp assembly (M) until the gear inside the clamp assembly meshes with the rack on the overarm. T ur n the T -handle screw ( S) counter -rclockwise until the clamp assembly (M) is secur ely positioned on the overarm assembly (B).
13 AL TERNA TE ASSEMBL Y ARRANGEMENT T o assemble the V ersa-Feeder TM in the mounting arrangement shown in Fig. 4, attaching the pivot ball to the overarm clamp assembly differs slightly . T o assemble: 1. Remove the overarm (A) Fig. 24 from the overarm clamp assembly (B).
14 6. Insert the straight end of the overarm (A) Fig. 29 through the housing (E). Attach the pivot ball (F) Fig. 29 to the over- arm (A) w ith a 3/8-16 x 1" socket hex head screw and lock- washer (K) Fig. 30. NOTE: Make certain that the screw a nd lockwasher (K) ar e recessed inside pivot ball (F).
15 MOUNTING THE VERSA-FEEDER TM TO A MACHINE T ABLE Decide on the location you wish to mount the V ersa-Feeder TM on your machine. Refer to Figs. 44, 45, and 46 for assistance when mounting the stock feeder assembly to a table saw , jointer , or shaper .
16 V ariable speeds from 10 FPM to 46 FPM are available with the stock feeder . T o change the feed rates, rotate the knob (A) Fig. 39 until the desired feed rate is indicat- ed by the pointer (B) on the knob. NOTE: Each dot on the feed rate scale (C) will increase or decrease the feed rate appr oximately 4 FPM.
17 REPLACING FEED ROLLERS Each feed roller is r emovable for repair or r eplacement. T o remove the feed rollers: 1. Loosen the three scr ews (A) Fig. 42 and remove the cover (B). 2. Remove the retaining ring (C) Fig. 43, and lift of f the feed roller (D).
18 TROUBLESHOOTING For assistance with your machine, visit our website at www .deltamachinery .com for a list of service centers or call the DEL T A Machinery help line at 1-800-223-7278 (In Canada call 1-800-463-3582). BRUSH INSPECTION AND REPLACEMENT DISCONNECT MACHINE FROM THE POWER SOURCE .
19 P AR TS, SERVICE OR WARRANTY ASSIST ANCE All Delta Machines and accessories are manufactur ed to high quality standards and ar e serviced by a network of Porter -Cable • Delta Factory Service Centers and Delta Authorized Service Stations.
The following are trademarks of POR TER-CABLE • DEL T A (Las siguientes son marcas registradas de POR TER-CABLE • DEL T A S.A.) (Les marques suivantes sont des marques de fabriquant de la POR TER-CABLE • DEL T A): Auto-Set ® , BAMMER ® , B.O.S.
Een belangrijk punt na aankoop van elk apparaat Delta 36-865 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Delta 36-865 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Delta 36-865 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Delta 36-865 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Delta 36-865 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Delta 36-865 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Delta 36-865 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Delta 36-865 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
