Gebruiksaanwijzing /service van het product 37-380 van de fabrikant DeWalt
Ga naar pagina of 28
INSTRUCTION MANUAL 8" Pr ofessional Jointer (Model 37-380) P ART NO. 909568 - 07-10-03 Copyright © 2003 Delta Machinery T o learn more about DEL T A MACHINER Y visit our website at: www .deltamachinery .com. For Parts, Service, W arranty or other Assistance, please call 1-800-223-7278 ( In Canada call 1-800-463-3582).
2 Indicates an imminently hazardous situation which, if not avoided, will r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, could r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, may r esult in minor or moderate injury .
3 F AILURE TO FOLLOW THESE RULES MA Y RESUL T IN SERIOUS PERSONAL INJUR Y . 1. FOR YOUR OWN SAFETY , READ THE INSTRUC- TION MANUAL BEFORE OPERA TING THE MACHINE. Learning the machine’ s application, limitations, and specific hazards will gr eatly minimize the possibility of accidents and injury .
4 ADDITIONAL SAFETY RULES FOR JOINTERS 1. DO NOT OPERA TE THIS MACHINE until it is completely assembled and installed according to the instructions. A machine incorrectly assembled can cause serious injury .
5 A separate electrical circuit should be used for your machines. This cir cuit should not be less than #12 wire and should be protected with a 20 Amp time lag fuse. If an extension cor d is used, use only 3-wire extension cords which have 3- prong gr ounding type plugs and matching receptacle which will accept the machine’ s plug.
6 Use proper extension cor ds. Make sure your extension cord is in good condition and is a 3-wir e extension cord which has a 3-pr ong grounding type plug and matching receptacle which will accept the machine’ s plug. When using an extension cord, be sur e to use one heavy enough to carry the current of the machine.
7 JOINTER P AR TS Fig. 2 1. Jointer 2. Fence Carriage Assembly 3. Cutterhead Pulley Guard/Carriage Mounting Bracket 4. T able Raising Handle 5. Switch Mounting Bracket 6. Cutterhead Guard 7. Fence Tilting Handles (2) 8. Fence 9. Push Blocks (2) 10. 6mm Hex Wrench 11.
8 Fig. 3 16. Stand with Pre-Wir ed Switch 17. Dust Chute 18. V -Belt 19. Pulley 20. 3/8-16x2" Hex Head Screw (3) 21. M8x1.25x55mm Hex Socket Head Screw (4) 22. M8x1.25x25mm Hex Socket Head Screw (2) 23. M8x1.25x20mm Hex Socket Head Screw (2) 24. M8x1.
9 2. Remove the four bolts that attach the motor (A) Fig. 5 to top of the stand. NOTE: SA VE THESE BOL TS AS THEY WILL BE USED TO A TT ACH THE MOTOR TO THE MOUNTING BRACKETS. Fig. 5 5. Line up three holes (F) and (L) Fig. 6, on top of stand with three holes located at the bottom of the jointer base.
10 ASSEMBLING MOTOR PULLEY Assemble motor pulley (K) Fig. 10, to motor shaft with the hub of the pulley in the outer position as shown. Make certain key (L) is inserted in the keyway of the pulley and motor shaft, then tighten set screw (M) using the 3 mm hex wrench (not shown).
11 2. Using the supplied 6mm hex wrench (E) Fig. 14, fasten bracket (C) onto jointer base (G). Place a M8.1 lockwasher then an M8 flat washer on an M8x1.25x55mm hex socket head screw . Insert the screw (D) Fig. 14, through the hole in bracket (C), and thr ead the screw into the jointer base (G), and tighten securely .
12 2. Fig. 18 illustrates fence properly mounted. Fig. 18 3. Thread shorter fence handle (E ) Fig.19, into infeed end of fence (A) and longer fence handle (G) into outfeed end as shown. Fig. 19 E G A ASSEMBLING CUTTERHEAD GUARD 1. Remove set screw (not shown) fr om cutterhead guard post (F) with the 2.
13 ASSEMBLING SWITCH AND MOUNTING BRACKET 1. Align the two holes in the switch mounting bracket (A) Fig 22, with the two holes (D) in the back of the infeed table (B). Place an M8.1 lockwasher (E) Fig. 22, then an M8 flat washer (F), on an M8x1.25x16mm hex socket head screw (C).
14 OPERA TING CONTROLS AND ADJUSTMENTS ST ARTING AND STOPPING JOINTER 1. The on/off switch is located underneath the switch shield (B) Fig. 31. T o start the jointer , move switch (A) up to the “ON” position. 2. T o turn the jointer “OFF”, push down on switch shield (B) Fig.
15 2. Raise or lower the infeed table adjustment lever (C) Fig. 35. 3. IMPORT ANT : When lowering the infeed table, a depth stop (D) Fig. 35, will automatically stop the table at a 1/8" depth-of-cut. T o move the table past this point, the depth stop (D) Fig.
16 KNIFE ADJUSTMENTS In order to do accurate work, the knives must be exactly level with the outfeed table. T o check and adjust, proceed as follows: DISCONNECT MACHINE FROM POWER SOURCE . 1. Loosen infeed table lock lever and lower infeed table as described under section “INFEED T ABLE ADJUSTMENTS” .
17 ADJUSTING T ABLE GIBS “Gibs”’ are pr ovided to take up any play that may develop between the mating dovetailed ways of the base and the infeed and outfeed tables, due to excessive wear . The gib for the infeed table is shown at (A) Fig. 46. Proper gib adjustment is necessary for the functioning of the jointer .
18 FENCE OPERA TION The fence can be moved across the table and can tilt 45 degrees right or left at any position on the table as follows: NOTE: SWITCH HAS BEEN REMOVED FOR CLARITY OF ILLUSTRA TIONS ONL Y . 1. T o move the fence across the table, loosen lock handle (A) Fig.
19 4. Rotate flip stop (F) Fig. 54, and tilt the fence outward as far as it will go and tighten locking handle (D). Place a square (K) on the table and against the fence to check if the fence is 45 degrees outwar d to the table. 5. If an adjustment to the positive stop is necessary , loosen locking handle (D) Fig.
20 KNIVES MUST BE INST ALLED CORRECTL Y AS SHOWN IN FIG. 58 . 8. The knives are adjusted corr ectly when the cutting edge of the knife extends out .060” from the cutterhead diameter . 9. Carefully r otate the cutterhead (G) Fig. 59, until the round portion of the cutterhead is on top as shown.
21 OPERA TION The following directions will give the beginner a start on jointer operations. Use scrap pieces of lumber to check settings and to get the feel of the operations before attempting regular work. THE KNIVES ON THE JOINTER WILL NOT WEAR EVENL Y BY FEEDING THE WOOD THROUGH THE SAME SPOT ON THE T ABLE EVER Y TIME.
22 SURF ACING Surfacing is identical to the jointing operation except for the position of the workpiece. For surfacing, the major flat surface of the workpiece is placed on the infeed table of the jointer with the narrow edge of the workpiece against the fence, as shown in Fig.
23 SURF ACING WARPED PIECES If the wood to be surfaced is dished or warped, take light cuts until the surface is flat. Avoid for cing such material down against the table; excessive pressur e will spring it while passing the knives, and it will spring back and remain curved after the cut is completed.
24 PUSH STICK MAKE FROM 1/2" OR 3/4" WOOD OR THICKNESS LESS THAN WIDTH OF MA T’L. TO BE CUT CUT OFF HERE TO PUSH 1/4" WOOD CUT OFF HERE TO PUSH 1/2" WOOD NOTCH TO HELP PREVENT HA.
25 NOTES.
26 NOTES.
27 P AR TS, SER VICE OR W ARRANTY ASSIST ANCE All Delta Machines and accessories are manufactur ed to high quality standards and are serviced by a network of Porter -Cable • Delta Factory Service Centers and Delta Authorized Service Stations.
The following are trademarks of POR TER-CABLE · DEL T A (Las siguientes son marcas r egistradas de PORTER-CABLE S.A.): Auto-Set ® , BAMMER ® , B.O.S.
Een belangrijk punt na aankoop van elk apparaat DeWalt 37-380 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen DeWalt 37-380 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens DeWalt 37-380 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding DeWalt 37-380 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over DeWalt 37-380 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van DeWalt 37-380 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de DeWalt 37-380 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met DeWalt 37-380 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
