Gebruiksaanwijzing /service van het product 2010 Challenger van de fabrikant Dodge
Ga naar pagina of 469
Challenger O W N E R ’ S M A N U A L 2010.
T ABLE OF CONTENTS SECTION P AGE 1 INTRODUCTION ............................................................ 3 2 THINGS TO KNOW BEFORE ST AR TING YOUR VEHICLE .............................. 9 3 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE ............
.
INTRODUCTION CONTENTS 䡵 Introduction ........................... 4 䡵 How T o Use This Manual .................. 4 䡵 W arnings And Cautions ................... 6 䡵 V ehicle Identification Number .............. 6 䡵 V ehicle Modifications/Alterations .
INTRODUCTION Congratulations on selecting your new Chrysler Group LLC vehicle. Be assured that it r epresents pr ecision workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles.
1 INTRODUCTION 5.
W ARNINGS AND CAUTIONS This Owner’s Manual contains W ARNINGS against op- erating procedur es that could result in an accident or bodily injury . It also contains CAUTIONS against proce- dures that could r esult in damage to your vehicle. If you do not read this entir e manual, you may miss important information.
VEHICLE MODIFICA TIONS/AL TERA TIONS W ARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
.
THINGS T O KNOW BEFORE ST ARTING YOUR VEHICLE CONTENTS 䡵 A W or d About Y our Keys ................. 1 2 ▫ W ireless Ignition Node (WIN) ............ 1 2 ▫ K e y F O B ........................... 1 3 ▫ Removing Key FOB From Ignition ......... 1 4 ▫ Key-In-Ignition Reminder .
▫ T o Open The T runk .................... 2 4 ▫ Using The Panic Alarm ................. 2 4 ▫ Programming Additional T ransmitters ...... 2 5 ▫ T ransmitter Battery Replacement .......... 2 5 ▫ General Information ................... 2 5 䡵 Remote Starting System .
▫ Supplemental Restraint System (SRS) - Airbags ............................ 4 5 ▫ Airbag Deployment Sensors And Controls . . . 51 ▫ Event Data Recorder (EDR) .............. 5 8 ▫ Child Restraint ....................... 6 0 䡵 Engine Break-In Recommendations .
A WORD ABOUT YOUR KEYS Y our vehicle uses a keyless ignition system. This system consists of a Key Fob with Remote Keyless Entry (RKE) transmitter and a W ireless Ignition Node (WIN) with integral ignition switch. Y ou can insert the Key Fob into the ignition switch with either side up.
Key Fob The Key Fob operates the ignition switch. It also contains the Remote Keyless Entry (RKE) transmitter and an emergency key , which stores in the r ear of the Key Fob. The emergency key allows for entry into the vehicle should the battery in the vehicle or the Key Fob go dead.
T o remove the emergency key , slide the mechanical latch at the top of the Key Fob sideways with your thumb and then pull the key out with your other hand. NOTE: Y ou can insert the double-sided emergency key into the lock cylinders with either side up.
W ARNING! Never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or others could be seri- ously or fatally injured. Do not leave the Key Fob in the ignition or a vehicle equipped with Keyless Go in the ACC or RUN mode.
SENTR Y KEY 姞 The Sentry Key 威 Immobilizer System prevents unautho- rized vehicle operation by disabling the engine. The system does not need to be armed or activated. Operation is automatic, regar dless of whether the vehicle is locked or unlocked.
Replacement Keys NOTE: Only Key Fobs that are pr ogrammed to the vehicle electronics can be used to start and operate the vehicle. Once a Key Fob is programmed to a vehicle, it cannot be programmed to any other vehicle. CAUTION! • Always remove the Key Fobs from the vehicle and lock all doors when leaving the vehicle unattended.
VEHICLE SECURITY ALARM The V ehicle Security Alarm monitors the vehicle doors for unauthorized entry and the ignition switch for unau- thorized operation.
T o Disarm The System V ehicles Not Equipped with Keyless Go Either press the UNLOCK button on the RKE transmitter or insert a valid ignition key into the ignition switch. NOTE: • The driver’s door key cylinder and the trunk button on the RKE transmitter cannot arm or disarm the V ehicle Security Alarm.
T amper Alert If something has triggered the V ehicle Security Alarm in your absence, the horn will sound three times when you disarm the V ehicle Security Alarm. Check the vehicle for tampering. ILLUMINA TED ENTR Y The courtesy lights will turn on when you press the UNLOCK button on the Remote Keyless Entry (RKE) transmitter or open any door .
T o Unlock The Doors Press and r elease the UNLOCK button on the RKE transmitter once to unlock the driver’s door or twice within five seconds, to unlock both doors. The turn signal lights will flash to acknowledge the unlock signal. The illuminated entry system will also turn on.
3. T est the feature while outside of the vehicle by pr ess- ing the LOCK/UNLOCK buttons on the RKE transmitter with the ignition switch in the OFF position and the Key Fob removed. 4. Repeat these steps if you want to return this feature to its previous setting.
Alarm. Opening a door with the Security Alarm activated will cause the alarm to sound. Press the UNLOCK button to deactivate the Security Alarm. T urn Headlights On with Remote Key Unlock This feature activates the headlights for up to 90 seconds when the doors are unlocked with the RKE transmitter .
NOTE: Pressing the LOCK button on the RKE transmit- ter while you are in the vehicle will activate the Security Alarm. Opening a door with the Security Alarm activated will cause the alarm to sound. Press the UNLOCK button to deactivate the Security Alarm.
Programming Additional T ransmitters Programming Key Fobs or RKE transmitters may be performed at an authorized dealer . T ransmitter Battery Replacement The recommended r eplacement battery is CR2032. NOTE: Perchlorate Material – special handling may ap- ply .
NOTE: Changes or modifications not expressly ap- proved by the party r esponsible for compliance could void the user’s authority to operate the equipment. If your RKE transmitter fails to operate from a normal distance, check for these two conditions: 1.
W ARNING! • Do not start or run an engine in a closed garage or confined area. Exhaust gas contains Carbon Mon- oxide (CO) which is odorless and colorless. Car- bon Monoxide is poisonous and can cause serious injury or death when inhaled. • Keep Remote Keyless Entry (RKE) transmitters away from children.
T o Exit Remote Start Mode without Driving the V ehicle • Press and r elease the REMOTE ST AR T button one time or allow the engine to run for the entir e 15-minute cycle. NOTE: T o avoid unintentional shut downs, the system will disable the one time press of the REMOTE ST ART button for two seconds after receiving a valid Remote Start request.
DOOR LOCKS Manual Door Locks T o lock each door , push the door lock plunger on each door trim panel downward. T o unlock each door , pull the door lock plunger on each door trim panel upward. If the door lock plunger is down when you shut the door , the door will lock.
Power Door Locks The power door lock switch is located on each door trim panel. Use this switch to lock or unlock the doors. If you press the power door lock switch while the Key Fob is in the ignition, and either door is open, the power locks will not operate.
6. The doors were not previously locked using the power door lock switch or Remote Keyless Entry (RKE) transmitter Automatic Door Locks — If Equipped The auto door lock feature can be enabled or disabled by your authorized dealer . See your authorized dealer for programming.
4. W ithin 30 seconds, press the power door UNLOCK switch to unlock the doors. 5. A single chime will indicate the completion of the programming. NOTE: If you do not hear the chime, it means that the system did not enter the programming mode and you will need to repeat the pr ocedure.
NOTE: • The door window will lower slightly if it is closed completely when opening the door . The window will return to its fully closed position after closing the door . This action allows the door to open without resistance and prevents window and seal damage.
open or partially open positions. This is a normal occur- rence and can be minimized. If the buf feting occurs with one window open, then open the other window to minimize the buffeting. If the buf feting occurs with the sunroof open, then adjust the sunr oof opening to mini- mize the buffeting.
TRUNK SAFETY W ARNING W ARNING! Do not allow children to have access to the trunk, either by climbing into the trunk from outside, or through the inside of the vehicle. Always close the trunk lid when your vehicle is unattended. Once in the trunk, young children may not be able to escape, even if they entered through the rear seat.
OCCUP ANT RESTRAINTS Some of the most important safety features in your vehicle are the r estraint systems: • Three-point lap and shoulder belts for the driver and all passengers • Advanced Front .
W ARNING! In a collision, you and your passengers can suffer much greater injuries if you are not properly buckled up. Y ou can strike the interior of your vehicle or other passengers, or you can be thrown out of the vehicle. Always be sure you and others in your vehicle are buckled up properly .
W ARNING! • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seri- ously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.
2. The seat belt latch plate is contacting the seat when the belt is routed thr ough the seat web guide. When the belt is routed outside of the seat web guide, the latch plate will contact the quarter trim panel. Grasp the latch plate and pull out the belt.
W ARNING! • A belt that is buckled into the wrong buckle will not protect you properly . The lap portion could ride too high on your body , possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you as well.
W ARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as pos- sible and keep it snug. • A twisted belt cannot do its job as well.
W ARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically , checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately . Do not disassemble or modify the system.
When T o Use The Automatic Locking Mode Use the Automatic Locking Mode anytime a child safety seat is installed in the rear outboar d seating position. Children 12 years old and younger should always be properly r estrained in the rear seat. How T o Use The Automatic Locking Mode 1.
Enhanced Seat Belt Use Reminder System (BeltAlert 姞 ) If the driver’s seat belt has not been buckled within 60 seconds of starting the vehicle and if the vehicle speed is greater than 5 mph (8 km/h), the BeltAlert 威 will alert the driver to buckle the seat belt.
4. T urn the ignition switch to the OFF position. A single chime will sound to signify that you have successfully completed the programming. The BeltAlert 威 can be reactivated by r epeating this pro- cedure.
mounted in the center of the steering wheel. The passen- ger’s front airbag is mounted in the instr ument panel, above the glove compartment. The words SRS AIRBAG are embossed on the airbag covers. NOTE: These airbags are certified to the new Federal regulations for Advanced Airbags.
• Airbag W arning Light • Driver Front Airbag • Front Passenger Airbag • Front and Side Impact Sensors • Steering Wheel and Column • Instrument Panel • Knee Impact Bolster • Front Seat.
W ARNING! (Continued) • Do not put anything on or around the airbag covers or attempt to open them manually . Y ou may damage the airbags and you could be injured because the airbags may no longer be functional. The protective covers for the airbag cushions are designed to open only when the airbags are inflat- ing.
NOTE: • Should a vehicle rollover occur , the pretensioners and/or SABIC airbags on both sides of the vehicle may deploy . • Airbag covers may not be obvious in the interior trim; but they will open during airbag deployment.
Along with seat belts and pretensioners, Advanced Front Airbags work with the knee bolsters to provide impr oved protection for the driver and fr ont passenger .
Do not lean against the door . If your vehicle has side airbags, and deployment occurs, the side airbags will inflate forcefully into the space between you and the door . If the airbag system in this vehicle needs to be modified to accommodate a disabled person, contact the Customer Center .
ORC deploys the Advanced Fr ont Airbags, SABIC air- bags — if equipped, and front seat belt pr etensioners — if equipped, as requir ed, depending on severity and type of impact.
The ORC contains a backup power supply system that may deploy the airbags even if the battery loses power or it becomes disconnected prior to deployment. Also, the ORC turns on the Airbag W arning Light in the instrument panel for appr oxi- mately six to eight seconds for a self-check when the ignition is first turned on.
of the way as the bags inflate to their full size. The bags fully inflate in about 50 to 70 milliseconds. This is about half of the time it takes to blink your eyes. The bags then quickly deflate while helping to restrain the driver and front passenger .
Front and Side Impact Sensors In front and side impacts, impact sensors aid the ORC in determining appropriate r esponse to impact events. Ad- ditional sensors in the ORC determine the level of airbag deployment and provide verification.
However , if you haven’t healed significantly within a few days, or if you have any blistering, see your doctor immediately . • As the airbags deflate, you may see some smoke-like particles. The particles are a normal by-pr oduct of the process that generates the non-toxic gas used for airbag inflation.
Maintaining Y our Airbag System W ARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. Y ou could be injured if the airbag system is not there to protect you.
Airbag W arning Light Y ou will want to have the airbags ready to inflate for your protection in a collision. While the airbag system is designed to be mainte- nance free, if any of the following occurs, have an authorized dealer service the system immediately .
2. Under certain circumstances, EDR data may not be recor ded (e.g., loss of battery power). In conjunction with other data gathered during a com- plete accident investigation, the electronic data may.
3. Requested by police under a legal warrant. 4. Otherwise required by law . Data parameters that are r ecorded: • Diagnostic trouble code(s) and warning light status for electronically-contr olled .
There ar e differ ent sizes and types of restraints for children fr om newborn size to the child almost large enough for an adult safety belt. Always check the child seat Owner’s Manual to ensure you have the corr ect seat for your child. Use the restraint that is corr ect for your child.
than one year . These child seats are also held in the vehicle by the lap/shoulder belt or the LA TCH child restraint anchorage system. Refer to “LA TCH — Child Seat Anchorage System (Lower Anchors and T ether for CHildren)”.
W ARNING! • Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions ex- actly when installing an infant or child restraint.
LA TCH — Child Seat Anchorage System (Lower Anchors and T ether for CHildren) Y our vehicle’s rear seat is equipped with the child restraint anchorage system called LA TCH.
Installing the LA TCH-Compatible Child Restraint System W e urge you to follow the manufacturer’s dir ections carefully when installing your child r estraint. Not all child restraint systems will be installed as described her e. Again, carefully follow the installation instr uctions that are pr ovided with the child restraint system.
means of adjusting the tension in the strap. Forward- facing toddler restraints and some r ear-facing infant restraints will also be equipped with a tether strap, a hook for attachment to the tether strap anchorage and a means of adjusting the tension of the strap.
W ARNING! Improper installation of a child restraint to the LA TCH anchorages can lead to failure of an infant or child restraint. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint.
T o attach a child restraint tether strap: 1. Rotate the cover over the anchor directly behind the seat where you ar e placing the child restraint. 2. Route the tether strap to provide the most dir ect path for the strap between the anchor and the child seat.
T ransporting Pets Airbags deploying in the front seat could harm your pet. An unrestrained pet will be thr own about and possibly injured, or injure a passenger during panic braking or in a collision. Pets should be restrained in the r ear seat in pet harnesses or pet carriers that are secur ed by seat belts.
SAFETY TIPS T ransporting Passengers NEVER TRANSPOR T P ASSENGERS IN THE CARGO AREA. W ARNING! • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seri- ously injured or killed.
If you are r equired to drive with the tr unk/liftgate open, make sure that all windows ar e closed and the climate control BLOWER switch is set at high speed. DO NOT use the recir culation mode. The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system.
Defroster Check operation by selecting the defrost mode and place the blower control on high speed. Y ou should be able to feel the air directed against the windshield.
UNDERST ANDING THE FEA TURES OF YOUR VEHICLE CONTENTS 䡵 Mirrors .............................. 7 7 ▫ Automatic Dimming Mirror — If Equipped . . . 77 ▫ Outside Mirrors ...................... 7 8 ▫ Outside Mirrors Folding Featur e .......... 7 8 ▫ Power Mirrors .
䡵 V oice Command — If Equipped ........... 1 0 9 ▫ V oice Command System Operation ........ 1 0 9 ▫ Commands ......................... 1 1 1 ▫ V oice T raining ...................... 1 1 4 䡵 Seats .............................. 1 1 4 ▫ Power Seats .
▫ Flash-T o-Pass ....................... 1 2 7 ▫ Overhead Console Map/Reading Lights .... 1 2 8 ▫ Interior Lights ...................... 1 2 9 䡵 W indshield W ipers And W ashers .......... 1 3 0 ▫ Intermittent W iper System .............. 1 3 0 ▫ Mist Feature .
▫ Security ........................... 1 4 2 ▫ T roubleshooting T ips .................. 1 4 3 ▫ General Information .................. 1 4 3 䡵 Power Sunroof — If Equipped ............ 1 4 4 ▫ Opening Sunroof — Partially ............ 1 4 5 ▫ Opening Sunroof — Expr ess .
MIRRORS Automatic Dimming Mirror — If Equipped This mirror automatically adjusts for headlight glar e from vehicles behind you. Y ou can turn the feature on or off by pr essing the button at the base of the mirror . A light next to the button will illuminate to indicate when the dimming feature is activated.
Outside Mirrors T o receive maximum benefit, adjust the outside mirror(s) to center on the adjacent lane of traffic and a slight overlap of the view obtained from the inside mirr or . NOTE: The passenger side convex outside mirror will give a much wider view to the rear , and especially of the lane next to your vehicle.
Power Mirrors The power mirror switch is located on the driver’s door trim panel, next to the power door lock switch. A r otary knob selects the left mirror , right mirror or off position. After selecting a mirror , move the knob in the same direction you want the mirr or to move.
mirror cover upwar d. The light turns on automatically . Close the mirror cover to turn of f the light. “Slide-On-Rod” and Extender Features of Sun Visor T o use the “Slide-On-Rod” feature of .
Uconnect™ Phone — IF EQUIPPED Uconnect™ Phone is a voice-activated, hands-free, in- vehicle communications system. Uconnect™ Phone al- lows you to dial a phone number with your cellular phone using simple voice commands (e.g., ⬙ Call” ѧ “Mike” ѧ ”W ork ⬙ or ⬙ Dial” ѧ “248-555-1212 ⬙ ).
system. Only one linked (or paired) cellular phone can be used with the system at a time. The system is available in English, Spanish, or French languages. W ARNING! Any voice commanded system should be used only in safe driving conditions following local laws and phone use.
The radio display will be used for visual prompts fr om the Uconnect™ Phone such as ⬙ CELL ⬙ or caller ID on certain radios. Operation V oice commands can be used to operate the Uconnect™ Phone and to navigate through the Uconnect™ Phone menu structur e.
T o activate the Uconnect™ Phone from idle, simply press the button and follow the audible prompts for directions. All Uconnect™ Phone sessions begin with a press of the button on the radio control head. Cancel Command At any prompt, after the beep, you can say ⬙ Cancel ⬙ and you will be returned to the main menu.
• Y ou will then be asked to give your cellular phone a priority level between one and seven, with one being the highest priority . Y ou can pair up to seven cellular phones to your Uconnect™ Phone. However , at any given time, only one cellular phone can be in use, connected to your Uconnect™ Phone.
or downloaded phonebook. T o learn how to store a name in the phonebook, refer to ⬙ Add Names to Y our Uconnect™ Phonebook, ⬙ in the phonebook. • The Uconnect™ system will confirm the name and then dial the corresponding phone number , which may appear in the display of certain radios.
Phonebook Download – Automatic Phonebook T ransfer From Cellular Phone If equipped and specifically supported by your phone, Uconnect™ Phone automatically downloads names (text names) and number entries from the cellular phone’s phonebook. Specific Bluetooth 威 Phones with Phone Book Access Profile may support this featur e.
Phonebook Download — Single Entry If equipped and supported by your phone, Uconnect™ Phone allows the user to download entries from their phone via Bluetooth 威 .
• Y ou will then be asked for the name of the phonebook entry that you wish to edit. • Next, choose the number designation (home, work, cellular , or pager) that you wish to edit. • When prompted, r ecite the new phone number for the phonebook entry that you are editing.
• After you enter the name, the Uconnect™ Phone will ask you which designation you wish to delete: home, work, cellular , pager , or all. Say the designation you wish to delete. • Note that only the phonebook entry in the current language is deleted.
• The Uconnect™ Phone will then prompt you as to the number designation you wish to call. • The selected number will be dialed. Phone Call Features The following features can be accessed thr ough the Uconnect™ Phone if the feature(s) ar e available on your cellular service plan.
by the phone number or phonebook entry you wish to call. The first call will be on hold while the second call is in progr ess. T o go back to the first call, refer to ⬙ T oggling Between Calls ⬙ in this section. T o combine two calls, refer to ⬙ Conference Call ⬙ in this section.
on hold may not become active automatically . This is cell phone-dependent. T o bring the call back from hold, press and hold the button until you hear a single beep. Redial • Press the button to begin. • After the ⬙ Ready ⬙ prompt and the following beep, say ⬙ Redial.
• After the ⬙ Ready ⬙ prompt and the following beep, say the name of the language you wish to switch to English, Espanol, or Francais. • Continue to follow the system prompts to complete the language selection. After selecting one of the languages, all prompts and voice commands will be in that language.
• The Uconnect™ Phone does slightly lower your chances of successfully making a phone call as to that for the cellular phone directly . W ARNING! Y our phone must be turned on and paired to the Uc.
V oice Mail Calling T o learn how to access your voice mail, refer to ⬙ W orking with Automated Systems. ⬙ W orking with Automated Systems This method is used in instances where one generally has to press numbers on the cellular phone keypad while navigating through an automated telephone system.
NOTE: • Y ou may not hear all of the tones due to cellular phone network configurations. This is normal. • Some paging and voice mail systems have system time out settings that are too short and may not allow the use of this feature.
dialing a number with your paired Bluetooth 威 cellular phone, the audio will be played through your vehicle’s audio system. The Uconnect™ Phone will work the same as if you dial the number using V oice Command.
Connect or Disconnect Link Between the Uconnect™ Phone and Cellular Phone Y our cellular phone can be paired with many differ ent electronic devices, but can only be actively ⬙ connected ⬙ with one electronic device at a time.
• The selected phone will be used for the next phone call. If the selected phone is not available, the Uconnect™ Phone will return to using the highest priority phone present in or near (appr oximately within 30 ft (9 m)) the vehicle. Delete Uconnect™ Phone Paired Cellular Phones • Press the button to begin.
Repeat the words and phrases when pr ompted by the Uconnect™ Phone. For best results, the V oice T raining session should be completed when the vehicle is parked with the engine running, all windows closed, and the blower fan switched off. This procedur e may be repeated with a new user .
• When navigating through an automated system such as voice mail, or when sending a page, at the end of speaking the digit string, make sure to say ⬙ Send. ⬙ • Storing names in the phonebook when the vehicle is not in motion is recommended. • It is not recommended to stor e similar sounding names in the Uconnect™ Phonebook.
• Echo at the phone far end can sometimes be reduced by lowering the in-vehicle audio volume. • In a convertible vehicle, system performance may be compromised with the convertible top down. Bluetooth 威 Communication Link Cellular phones have been found to lose connection to the Uconnect™ Phone.
104 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE.
3 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 105.
106 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE.
V oice Commands Primary Alternate(s) zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location all V oice Commands Primary Alternate(s) call cancel confirmation prompt.
V oice Commands Primary Alternate(s) language list names list phones mobile mute mute off new entry no pager pair a phone phone pairing pairing phonebook phone book previous recor d again redial V oic.
General Information This device complies with Part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • Changes or modifications not expressly appr oved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: If you do not say a command within a few seconds, the system will present you with a list of options. If you ever wish to interrupt the system while it lists options, press the V oice Command button, listen for the beep, and say your command. Pressing the V oice Command button while the system is speaking is known as “barging in.
Commands The V oice Command system understands two types of commands. Universal commands are available at all times. Local commands are available if the supported radio mode is active. Changing the V olume 1. Start a dialogue by pressing the V oice Command button.
Radio FM T o switch to the FM band, say “FM” or “Radio FM”. In this mode, you may say the following commands: • “Frequency” (to change the fr equency) • “Next Station” (to select t.
Memo T o switch to the voice recorder mode, say “Memo”. In this mode, you may say the following commands: • “New Memo” (to recor d a new memo) — During the recor ding, you may press the V oice Command button to stop recor ding.
NOTE: Keep in mind that you have to press the V oice Command button first and wait for the beep before speaking the “Bar ge In” commands. V oice T raining For users experiencing difficulty with the system r ecog- nizing their voice commands or numbers the Uconnect™ V oice “V oice T raining” feature may be used.
switch is used to adjust the angle of the seatback. Push forward or r earward on the switch to change the position of the seatback. W ARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control.
Manual Front Seatback Recline T o recline: 1. Lean forward in the seat and lift the handle, then lean back to the desired position and r elease the handle. 2. Lift the handle to return the seatback to an upright position. W ARNING! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest.
Head Restraints Head restraints can r educe the risk of injury in the event of a rear impact. The head r estraints should be adjusted so the top of the head restraint is located above the top of your ear . T o raise it, pull upward on the head restraint.
W ARNING! Driving a vehicle with the head restraints removed or improperly adjusted could cause serious injury or death in the event of a collision. The head restraints should always be checked prior to operating the vehicle and never adjusted while the vehicle is in motion.
Press the switch once to select High-level heat- ing. Press the switch a second time to select Low-level heating. Press the switch a thir d time to shut the heating elements Off. If high level heating is selected, the system will automati- cally switch to the low level after 30 minutes of continu- ous operation.
CAUTION! Repeated overheating of the seat could damage the heating element and/or degrade the material of the seat. Easy Entry Seats Pulling upward on the lever , located on the seatback, allows the seatback to dump forward and the seat to slide forward.
Folding Rear Seat The rear seatbacks can be folded forwar d to provide an additional storage area. Pull on the loops shown in the illustration to fold down either or both seatbacks.
TO OPEN AND CLOSE THE HOOD T wo latches must be released to open the hood. 1. Pull the hood release lever located under the left side of the instrument panel. 2. Move to the outside of the vehicle and push the safety catch to the left. The safety catch is located under the center front edge of the hood.
CAUTION! T o prevent possible damage, do not slam the hood to close it. Lower the hood until it is open approxi- mately 6 in (15 cm), and then drop it. This should secure both latches. Never drive your vehicle unless the hood is fully closed, with both latches engaged.
Rotate the headlight switch clockwise to the first detent for parking light and instrument panel light operation. T urn it to the second detent for headlight, parking light and instrument panel light operation. Automatic Headlights — If Equipped This system automatically turns the headlights on or off according to ambient light levels.
T o activate the delay feature, place the ignition in the OFF position while the headlights are still on. Then, turn of f the headlights within 45 seconds.
An indicator light in the instrument cluster illuminates when the fog lights are turned on. NOTE: The fog lights will operate with the low beam headlights or parking lights on. However , selecting the high beam headlights will turn off the fog lights.
NOTE: • If either light remains on and does not flash, or ther e is a very fast flash rate, check for a defective outside light bulb. If an indicator fails to light when the lever is moved, it would suggest that the indicator bulb is defective.
Overhead Console Map/Reading Lights These lights are mounted between the sun visors on the overhead console. Each light is turned on by pr essing the lens.
Interior Lights The interior lights come on when a door is opened. T o protect the battery , the interior lights will turn off automatically 10 minutes after the ignition is placed in the OFF position. This will occur if the interior lights were switched on manually or ar e on because a door is open.
WINDSHIELD WIPERS AND W ASHERS The multifunction lever operates the windshield wipers and washer when the ignition is placed in the RUN position. The multifunction lever is located on the left side of the steering column.
Mist Feature Push the multifunction lever inward (towar d the steering column) to the first detent to activate a single wipe cycle to clear off r oad mist or spray from a passing vehicle. The wipers will continue to operate until you release the multifunction lever .
The Headlights On with W ipers feature can be enabled or disabled. Refer to “Electronic V ehicle Information Center (EVIC)/Personal Settings (Customer-Pr ogrammable Fea- tures)” in “Understanding Y our Instrument Panel” for further information.
outward or push it inwar d as desired. T o lock the steering column in position, push the control handle inwar d until fully engaged. W ARNING! Do not adjust the steering column while driving. Adjusting the steering column while driving or driv- ing with the steering column unlocked, could cause the driver to lose control of the vehicle.
simultaneously . If this occurs, the Electronic Speed Con- trol System can be r eactivated by pushing the Electronic Speed Control ON/OFF button and r esetting the desired vehicle set speed. T o Activate Push and release the ON/OFF button located on the end of the Electronic Speed Contr ol lever .
• Press the brake pedal, or pr ess the clutch pedal to the floor (manual transmission). • Pull the speed control lever towar d you (CANCEL). Pushing and releasing the ON/OFF button or turning the ignition OFF erases the set speed from memory .
T o Accelerate For Passing Press the accelerator as you would normally . When the pedal is released, the vehicle will r eturn to the set speed. Using Electronic Speed Control on Hills NOTE: The Electronic Speed Contr ol system maintains speed up and down hills.
Courtesy/Reading Lights At the forward end of the over head console are two courtesy/reading lights. Press the lens to turn on the light. Pr ess it a second time to turn off the light.
The HomeLink 威 buttons are located in the over head console, and contain one, two or three dots/lines desig- nating the differ ent HomeLink 威 channels. NOTE: HomeLink 威 is disabled when the V ehicle Secu- rity Alarm is active. W ARNING! • Y our motorized door or gate will open and close while you are training the Universal T ransceiver .
Programming HomeLink 姞 Before Y ou Begin If you have not trained any of the HomeLink 威 buttons, erase all channels before you begin training. T o do this, press and hold the two outside buttons for up to 20 seconds. The EVIC will display “CLEARING CHANNELS.
NOTE: Some gate operators and garage door openers may requir e you to replace Step 3 with pr ocedures noted in the “Gate Operator/Canadian Programming” section. 4. Press and hold the just-trained HomeLink 威 button. If the channel has been trained, the EVIC display will now state “CHANNEL # TRANSMIT .
6. Firmly press and release the LEARN or TRAINING button. The name and color of the button may vary by manufacturer . NOTE: Y ou have 30 seconds in which to initiate the next step after the LEARN button has been pressed. 7. Return to the vehicle and press the programmed HomeLink 威 button twice (holding the button for two seconds each time).
If you unplugged the device for training, plug it back in at this time. Then proceed with Step 4 under “Pr ogramming HomeLink 威 ” earlier in this section. Using HomeLink 姞 T o operate, press and release the pr ogrammed HomeLink 威 button. Activation will now occur for the trained device (i.
T roubleshooting Tips If you are having tr ouble programming HomeLink 威 , her e are some of the most common solutions: • Replace the battery in the original transmitter . • Press the LEARN button on the garage door opener to complete the training for rolling code.
POWER SUNROOF — IF EQUIPPED The power sunroof switch is located between the sun visors on the overhead console. W ARNING! • Never leave children in a vehicle with the key in the ignition switch (or with the ignition in the Accessory or Run position, for vehicles equipped with Keyless Go™).
W ARNING! (Continued) • Do not allow small children to operate the sun- roof. Never allow your fingers, other body parts, or any object, to project through the sunroof opening. Injury may result. Opening Sunroof — Partially Press and hold the switch in the r earward position.
Pinch Protect Feature This feature will detect an obstr uction in the opening of the sunroof during Expr ess Close operation. If an ob- struction in the path of the sunr oof is detected, the sunroof will automatically r etract. If this occurs remove the obstruction and pr ess the switch forward and r elease to Express Close.
Sunroof Maintenance Use only a nonabrasive cleaner and a soft cloth to clean the glass panel. Ignition Off Operation The power sunroof switch will r emain active for up to 60 minutes after the ignition is placed in the OFF posi- tion. Opening either door will cancel this feature.
NOTE: • T o ensure proper operation a MOP AR 威 knob and element must be used. • Do not exceed the maximum power of 160 W atts (13 Amps) at 12 V olts. If the 160 W att (13 Amp) power rating is exceeded the fuse protecting the system will need to be replaced.
W ARNING! T o avoid serious injury or death: • Only devices designed for use in this type of outlet should be inserted into any 12 V olt outlet. • Do not touch with wet hands. • Close the lid when not in use and while driving the vehicle. • If this outlet is mishandled, it may cause an electric shock and failure.
CAUTION! (Continued) • Power outlets are designed for accessory plugs only . Do not hang any type of accessory or acces- sory bracket from the plug. Improper use of the power outlet can cause damage. CUPHOLDERS Front Cupholders The front cupholders ar e located in the center console.
Rear Cupholders The rear seat cupholders ar e located in the center armrest between the rear seats. The cupholders ar e positioned forward in the armr est and side-by-side to provide conve- nient access to beverage cans or bottles while maintaining a resting place for the r ear occupants’ elbows.
Console Storage The center console has a storage compartment located underneath the armrest, and also contains a 12 V olt power outlet, a molded-in coin holder (designed to hold various size coins). The center console may also be equipped with a Universal Consumer Interface (UCI).
REAR WINDOW FEA TURES Rear Window Defroster The rear window defr oster button is located on the climate control (Mode) knob. Pr ess this button to turn on the rear window defr oster and the heated outside mirrors (if equipped). An indicator in the button will illuminate when the rear window defr oster is on.
.
UNDERST ANDING YOUR INSTRUMENT P ANEL CONTENTS 䡵 Instrument Panel Featur es ............... 1 5 8 䡵 Instrument Cluster – Base ............... 1 5 9 䡵 Instrument Cluster – Pr emium ............ 1 6 0 䡵 Instrument Cluster Descriptions ......
䡵 Media Center 730N/430 (RER/REN/RBZ) — AM/FM Stereo Radio And CD/DVD/HDD/ Nav — If Equipped ..................... 1 8 8 ▫ Operating Instructions — V oice Command System — If Equipped ................. 1 8 8 ▫ Operating Instructions — Uconnect™ phone — If Equipped .
▫ Using This Feature ................... 2 1 5 ▫ Controlling The iPod 威 Using Radio Buttons ........................... 2 1 5 ▫ Play Mode ......................... 2 1 5 ▫ List Or Browse Mode ................. 2 1 7 䡵 Uconnect™ Multimedia (Satellite Radio) — If Equipped (REN/REQ/RER/RES Radios Only) .
INSTRUMENT P ANEL FEA TURES 1 — Air Outlets 5 — Heated Seat Switch 9 — Ignition Switch 2 — Instrument Cluster 6 — ESP OFF Switch 10 — T runk Release Button 3 — Glove Compartment 7 — Ha.
INSTRUMENT CLUSTER – BASE 4 UNDERST ANDING YOUR INSTRUMENT P ANEL 159.
INSTRUMENT CLUSTER – PREMIUM 160 UNDERST ANDING YOUR INSTRUMENT P ANEL.
INSTRUMENT CLUSTER DESCRIPTIONS 1. Fuel Gauge The pointer shows the level of fuel in the fuel tank when the ignition switch is placed in the RUN position. 2. T rip Odometer Button Premium Cluster Press this button to change the display fr om odometer to either of two trip odometer settings.
6. Charging System W arning Light This light shows the status of the electrical charg- ing system. The light should turn on when the ignition switch is placed in the RUN position and remain on briefly as a bulb check. If the light stays on or turns on while driving, turn off some of the vehicle’s non-essential electrical devices (i.
The gauge pointer will likely indicate a higher tempera- ture when driving in hot weather , up mountain grades, or when towing a trailer . It should not be allowed to exceed the upper limits of the normal operating range. CAUTION! Driving with a hot engine cooling system could damage your vehicle.
10. Airbag W arning Light This light will turn on for six to eight seconds as a bulb check when the ignition switch is first placed in the RUN position. If the light is either not on during starting, turns on while driving, or stays on, have the system inspected at an authorized dealer as soon as possible.
W ARNING! If a warning light remains on the system may not be working and you will not have the benefit of ESP or BAS. Under certain driving conditions, where ESP or BAS would be beneficial, you - if you have not adjusted your driving speeds and stopping in or to account for the lack of the feature, may be in acci- dent.
17. Shift Lever Indicator — Automatic T ransmission Only The Shift Lever Indicator is self-contained within the instrument cluster . It displays the gear position of the automatic transmission. 18. Front Fog Light Indicator — If Equipped This indicator will illuminate when the front fog lights are on.
On vehicles equipped with a Premium Instr ument Clus- ter , this display shows the Electronic V ehicle Information Center (EVIC) messages when the appropriate conditions exist. Refer to Electronic V ehicle Information Center (EVIC) for further information.
CHAngE OIL (Base Cluster) Y our vehicle is equipped with an engine oil change indicator system. The “CHAngE OIL” message will flash in the instrument cluster odometer for appr oximately 12 seconds after a single chime has sounded to indicate the next scheduled oil change interval.
The dual brake system provides a r eserve braking capac- ity in the event of a failure to a portion of the hydraulic system. A leak in either half of the dual brake system is indicated by the Brake W arning Light which will turn on when the brake fluid level in the master cylinder has dropped below a specified level.
The light also will turn on when the parking brake is applied with the ignition switch in the RUN position. NOTE: This light shows only that the parking brake is applied.
Y our vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly . The TPMS malfunction indicator is combined with the low tire pr essure telltale. When the system detects a malfunction, the telltale will flash for approximately one minute and then r emain continuously illuminated.
23. Anti-Lock Brake (ABS) Light This light monitors the Anti-Lock Brake System (ABS). The light will turn on when the ignition switch is placed in the RUN position and may stay on for as long as four seconds.
CAUTION! Prolonged driving with the MIL on could cause damage to the engine control system. It also could affect fuel economy and drivability . If the MIL is flashing, severe catalytic converter damage and power loss will soon occur . Immediate service is required.
ELECTRONIC VEHICLE INFORMA TION CENTER (EVIC) The Electronic V ehicle Information Center (EVIC) fea- tures a driver -interactive display which is located in the instrument cluster . This system conveniently allows the driver to select a variety of useful information by pressing the switches mounted on the steering wheel.
• Surround Sound modes (if equipped with Driver - Selectable Surround [DSS]) The system allows the driver to select information by pressing the following buttons mounted on the steering wheel.
Electronic V ehicle Information Center (EVIC) Displays When the appropriate conditions exist, the EVIC displays the following messages. • T urn Signal On (with a continuous warning chime if the vehicle is driven more than 1 mile [1.
• Right Front Low Pr essure (with a single chime) • Right Rear Low Pressur e (with a single chime) • Check TPM System (with a single chime) • ESP Of f – Electronic Stability Pr ogram is deac.
2. Fully depress the accelerator pedal, slowly , three times within 10 seconds. 3. T urn the ignition switch to the OFF/LOCK position. NOTE: If the indicator message illuminates when you start the vehicle, the oil change indicator system did not reset.
This feature allows you to monitor when you ar e driving in a fuel efficient manner , and it can be used to modify driving habits in order to incr ease fuel economy .
• Distance T o Empty (DTE) Shows the estimated distance that can be traveled with the fuel remaining in the tank. This estimated distance is determined by a weighted average of the instantaneous and average fuel economy , according to the current fuel tank level.
T o Reset The Display Reset will only occur while a resettable function is being displayed. Press and r elease the FUNCTION SELECT button once to clear the resettable function being dis- played.
Refer to “Keyless Go” in “Starting And Operating” for more information. NOTE: Under certain conditions, the display may be superseded by another display of higher priority . But when the ignition switch position is changed, the display always re-appears.
Automatic Compass Calibration This compass is self-calibrating, which eliminates the need to set the compass manually . When the vehicle is new , the compass may appear erratic and the EVIC will display “CAL” until the compass is calibrated.
NOTE: Keep magnetic materials away from the top of the instrument panel, such as iPod’s, Cell Phones, Lap- tops and Radar Detectors. This is where the compass module is located, and it can cause interference with the compass sensor , and it may give false readings.
• Oil Pressur e Shows the actual oil pressur e. • T ire Pr essure Shows the actual tire pr essure for each tir e (EXCLUDING THE SP ARE TIRE). Personal Settings (Customer-Programmable Features) Personal Settings allows the driver to set and recall features when the transmission is in P ARK.
Remote Key Unlock When Driver Door 1st Press is selected, only the driver’s door will unlock on the first press of the Remote Keyless Entry (RKE) transmitter UNLOCK button. When Driver Door 1st Press is selected, you must pr ess the RKE transmitter UNLOCK button twice to unlock the passen- ger door .
NOTE: T urning the headlights on during the daytime causes the instrument panel lights to dim. T o increase the brightness, refer to “Lights” in “Understanding The Features Of Y our V ehicle”.
T urn-by-T urn Navigation — If Equipped When ON is selected, the T urn-by-T urn directions will appear in the display as the vehicle approaches a desig- nated turn within a programmed r oute. T o make your selection, press and r elease the FUNCTION SELECT button until “ON” or “OFF” appears.
Operating Instructions — Uconnect™ Phone — If Equipped Refer to “Uconnect™ Phone” in “Understanding The Features Of Y our V ehicle”. Clock Setting Procedure — RBZ Radio T o Manually Set the Clock 1. T urn on the radio. 2. T ouch the screen wher e the time is displayed, the clock setting menu will appear on the screen.
Show T ime if Radio is Off When selected, this feature will display the time of day on the touch screen when the radio is turned of f. Proceed as follows to change the current setting: 1. T urn on the radio. 2. T ouch the screen where the time is displayed.
T o Manually Set the Clock — RER/REN 1. T urn on the radio. 2. T ouch the screen wher e the time is displayed. 3. T ouch the screen wher e “User Clock” is displayed, the clock setting menu will appear on the screen. 4. T o move the hour forward, touch the scr een where the word “Hour” with the arr ow pointing upward is dis- played.
Show T ime if Radio is Off When selected, this feature will display the time of day on the touch screen when the radio is turned of f. Proceed as follows to change the current setting: 1. T urn on the radio. 2. T ouch the screen wher e the time is displayed.
MEDIA CENTER 130 (RES) — AM/FM STEREO RADIO WITH CD PLA YER (MP3 AUX JACK) NOTE: The radio sales code is located on the lower right side of the radio faceplate. Operating Instructions — Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio.
SEEK Buttons Press and r elease the SEEK buttons to search for the next listenable station in AM/FM mode. Press the right switch to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection.
Push the rotary TUNE/SCROLL control knob a second time and MID will display . T urn the TUNE/SCROLL control knob to the right or left to incr ease or decrease the mid-range tones. Push the rotary TUNE/SCROLL control knob a third time and TREBLE will display .
Y ou may add a second station to each pushbutton by repeating the above pr ocedure with this exception: Pr ess the SET/RND button twice and SET 2 will show in the display window . Each button can be set for SET 1 and SET 2 in both AM and FM. This allows a total of 12 AM and 12 FM stations to be stored into pushbutton memory .
If you insert a disc with the ignition ON and the radio ON, the unit will switch from radio to CD mode and begin to play when you insert the disc. The display will show the track number , and index time in minutes and seconds. Play will begin at the start of track 1.
TIME Button Press this button to change the display fr om a large CD playing time display to a small CD playing time display . R W/FF Press and hold the FF (Fast Forwar d) button and the CD player will begin to fast forward until FF is r eleased, or R W or another CD button is pressed.
The radio uses the following limits for file systems: • Maximum number of folder levels: 8 • Maximum number of files: 255 • Maximum number of folders.
MPEG Specification Sampling Frequency (kHz) Bit Rate (kbps) MPEG-1 Audio Layer 3 48, 44.1, 32 320, 256, 224, 192, 160, 128, 1 12, 96, 80, 64, 56, 48, 40, 32 MPEG-2 Audio Layer 3 24, 22.05, 16 160, 128, 144, 1 12, 96, 80, 64, 56, 48, 40, 32, 24, 16, 8 ID3 T ag information for artist, song title, and album title are supported for version 1 ID3 tags.
Operation Instructions - Auxiliary Mode The auxiliary (AUX) jack is an audio input jack, which allows the user to plug in a portable device, such as an MP3 player , or cassette player , and utilize the vehicle’s audio system to amplify the source and play thr ough the vehicle speakers.
Operating Instructions — Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/V olume Control (Rotary) Push the ON/VOLUME control knob to turn on the radio. Push the ON/VOLUME control knob a second time to turn off the radio.
Phone Button Uconnect™ Phone — If Equipped Press this button to operate the Uconnect™ Phone featur e (if equipped). Refer to “Uconnect™ Phone” in “Under- standing The Features If Y our V ehicle”.
INFO Button Press the INFO button for an RDS station (one with call letters displayed). The radio will return a Radio T ext message broadcast fr om an FM station (FM mode only). R W/FF Pressing the R W (Rewind) or FF (Fast Forward) buttons causes the tuner to search for the next fr equency in the direction of the arr ows.
Push the rotary TUNE/SCROLL control knob again to exit setting tone, balance, and fade. MUSIC TYPE Button Pressing this button once will turn on the Music T ype mode for five seconds. Pressing the MUSIC TYPE button or turning the TUNE/SCROLL control knob within five seconds will allow the program format type to be se- lected.
Program T ype 16-Digit Character Display Soft Rhythm and Blues Soft R&B Sports Sports T alk T alk T op 40 T op 40 W eather W eather By pressing the SEEK button when the Music T ype icon is displayed, the radio will be tuned to the next frequency station with the same selected Music T ype name.
not selected within five seconds after pressing the SET/ RND button, the station will continue to play but will not be stored into pushbutton memory . Y ou may add a second station to each pushbutton by repeating the above pr ocedure with this exception: Pr ess the SET/RND button twice and SET 2 will show in the display window .
radio display . If a CD does not go into the slot more than 1.0 in (2.5 cm), a disc may already be loaded and must be ejected before a new disc can be loaded. If you insert a disc with the ignition ON and the radio ON, the unit will switch from radio to CD mode and begin to play when you insert the disc.
SEEK Button Press the right SEEK button for the next selection on the CD. Press the left SEEK button to r eturn to the beginning of the current selection, or r eturn to the beginning of the previous selection if the CD is within the first second of the current selection.
Supported Medium Formats (File Systems) The medium formats supported by the radio are ISO 9660 Level 1 and Level 2 and includes the Joliet extension. When reading discs r ecorded using formats other than ISO 9660 Level 1 and Level 2, the radio may fail to read files properly and may be unable to play the file nor - mally .
Supported MP3 File Formats The radio will recognize only files with the *.MP3 exten- sion as MP3 files. Non-MP3 files named with the *.MP3 extension may cause playback problems. The radio is designed to recognize the file as an invalid MP3 and will not play the file.
Loading times for playback of MP3 files may be affected by the following: • Media - CD-R W media may take longer to load than CD-R media • Medium formats - Multisession discs may take longer to lo.
Operation Instructions - Auxiliary Mode The auxiliary (AUX) jack is an audio input jack which allows the user to plug in a portable device such as an MP3 player or cassette player and utilize the vehicle’s audio system to amplify the source and play thr ough the vehicle speakers.
This feature allows you to plug an iPod 威 into the vehicle’s sound system through a 16–pin connector using the provided interface cable. UCI supports Mini, 4G, Photo, Nano, 5G iPod 威 and iPhone 威 devices. Some iPod 威 software versions may not fully support the UCI features.
Using This Feature By using the provided connection cable to connect an iPod 威 to the vehicle’s UCI 16–pin connector port: • The iPod 威 audio can be played on the vehicle’s sound system, providing metadata (artist, track title, album, etc.
• Jump backward in the curr ent track by pressing and holding the << RW button. Holding the << RW button long enough will take you to the beginning of the current track. • Jump forward in the curr ent track by pressing and holding the FF >> button.
Shuffle OFF modes for the iPod 威 .I ft h e RND icon is showing on the radio display , then the shuffle mode is ON. List Or Browse Mode During Play mode, pressing any of the buttons described below , takes you to List mode. List mode enables you to scroll thr ough the list of menus and tracks on the iPod 威 .
• T o Exit List mode without selecting a track, press the same PRESET button again to go back to Play mode . • LIST button: The LIST button will display the top level menu of the iPod 威 . T urn the TUNE control knob to list the top-menu item you wish to select and press the TUNE control knob.
Uconnect™ Multimedia (SA TELLITE RADIO) — IF EQUIPPED (REN/REQ/RER/RES RADIOS ONL Y) Satellite radio uses direct satellite-to-r eceiver broadcast- ing technology to provide clear digital sound, coast to coast. The subscription service provider is Sirius Satellite Radio.
Sirius ID number will display . The Sirius ID number display will time out in two minutes. Press any button on the radio to exit this screen. ESN/SID Access W ith REN/RER Radios While in SA T mode, press the MENU button on the radio faceplate. Next, touch the SUBSCRIPTION tab on the touch screen.
Operating Instructions - Uconnect™ Multimedia (Satellite) Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. SEEK Buttons Press and r elease the SEEK buttons to search for the next channel in Satellite mode. Press the right switch to seek up and the left switch to seek down.
MUSIC TYPE Button Pressing this button once will turn on the Music T ype mode for five seconds. Pressing the MUSIC TYPE button or turning the TUNE/SCROLL control knob within five seconds will allow the program format type to be se- lected. T oggle the MUSIC TYPE button again to select the music type.
Y ou may add a second channel to each pushbutton by repeating the above pr ocedure with this exception: Pr ess the SET button twice and SET 2 will show in the display window . Each button can be set for SET 1 and SET 2. This allows a total of 12 Satellite channels to be stored into pushbutton memory .
Y our vehicle is equipped with a state of the art audio amplifier that provides 5.1-channel surr ound sound from any stereo audio sour ce. A new feature of the KICKER 威 audio system offers the ability to choose surr ound sound for any audio source. “Audio Surround” is optimized for fr ont seat passengers for any audio source.
REMOTE SOUND SYSTEM CONTROLS — IF EQUIPPED The remote sound system contr ols are located on the surface of the steering wheel at the three and nine o’clock positions. V ehicles equipped with steering wheel-mounted buttons are also equipped with the Electr onic V ehicle Information Center (EVIC).
If the Compass/T emp/Audio screen is already displayed when the AUDIO MODE button is pressed, then the mode will change (i.e., from AM to FM, to Media mode, etc.
NOTE: If you experience difficulty in playing a particu- lar disc, it may be damaged (i.e., scratched, reflective coating removed, a hair , moisture or dew on the disc) oversized, or have copyright encoding. T ry a known good disc before considering disc player service.
Front Blower Control There ar e four blower speeds. Use this control to r egulate the amount of air forced thr ough the system in any mode you select. The blower speed increases as you move the contr ol clockwise from the of f position.
Mode Control (Air Direction) Mode control allows you to choose from several selections of air distribu- tion. Y ou can select either a primary mode, as identified by the symbols, or a blend of two of these modes. The closer the control is to a particular mode, the more air distribution you receive fr om that mode.
Defrost Mode Air is directed thr ough the windshield and side window demist outlets. Use DEFROST mode with maximum blower and temperature settings for best windshield and side window defrosting. NOTE: The air conditioning compressor operates in MIX and DEFROST , or a blend of these modes even if the A/C button is not pressed.
• The A/C can be deselected manually without disturb- ing the mode control selection. Economy Mode If ECONOMY mode is desir ed, press the A/C button to turn off the indicator light and the A/C compressor . Rotate the temperature contr ol knob to the desired temperature.
If Outside Ambient T emperature Is Mode Overrides T o T emperature Overrides T o Rear Window Defroster Active Less than 40°F Mix Full Heat Y es Between 40°F and 80°F No Override No Override No More.
V acation Storage Anytime you store your vehicle, or keep it out of service (i.e., vacation) for two weeks or more, r un the air conditioning system at idle for about five minutes in the fresh air and high blower settings.
Control Setting Suggestions for V arious W eather Conditions 234 UNDERST ANDING YOUR INSTRUMENT P ANEL.
ST ARTING AND OPERA TING CONTENTS 䡵 Starting Procedur es .................... 2 3 9 ▫ Manual T ransmission – If Equipped ....... 2 3 9 ▫ Automatic T ransmission – If Equipped ..... 2 4 0 ▫ Keyless Go™ – If Equipped ............. 2 4 1 ▫ Normal Starting .
▫ Five-Speed Automatic T ransmission ....... 2 5 6 ▫ Gear Ranges ........................ 2 5 6 䡵 AutoStick 威 — If Equipped ............... 2 6 0 ▫ AutoStick 威 — 3.5L Engine .............. 2 6 0 ▫ AutoStick 威 — 5.7L Engine ......
▫ Synchronizing ESP ................... 2 8 0 ▫ ESP/BAS Malfunction Indicator Light And ESP/TCS Indicator Light ............... 2 8 0 䡵 T ire Safety Information ................. 2 8 1 ▫ T ire Markings ....................... 2 8 1 ▫ T ire T erminology And Definitions .
▫ 5.7L Engine (W ith Manual T ransmission) .... 3 1 1 ▫ Reformulated Gasoline ................ 3 1 2 ▫ Gasoline/Oxygenate Blends ............. 3 1 2 ▫ E-85 Usage In Non-Flex Fuel V ehicles ...... 3 1 2 ▫ MMT In Gasoline .................... 3 1 3 ▫ Materials Added T o Fuel .
ST ARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust the inside and outside mirrors, fasten your seat belt, and if present, instr uct all other occupants to buckle their seat belts. W ARNING! • Never leave children alone in a vehicle.
W ARNING! Do not attempt to push or tow your vehicle to get it started. Unburned fuel could enter the catalytic con- verter and once the engine has started, ignite and damage the converter and vehicle. If the vehicle has a discharged battery , booster cables may be used to obtain a start from another vehicle.
Do not press the accelerator . Use the Fob with Integrated Key to briefly turn the ignition switch to the ST AR T position and release it as soon as the starter engages. The starter motor will continue to run, and it will disengage automatically when the engine is running.
NOTE: The ENGINE ST AR T/STOP button should only be removed or inserted with the ignition in the OFF position. Normal Starting Using the ENGINE ST AR T/STOP Button – Automatic T ransmission Only NOTE: Normal starting of either a cold or a warm engine is obtained without pumping or pressing the accelerator pedal.
2. The ignition switch will return to the OFF position. 3. If the shift lever is not in P ARK, the ENGINE ST AR T/ STOP button must be held for two seconds and vehicle speed must be above 5 mph (8 km/h) before the engine will shut off.
• If the vehicle speed is above 5 mph (8 km/h), the ENGINE ST AR T/STOP button must be held for two seconds before the engine will shut of f. The ignition switch position will remain in the ACC position until the vehicle is stopped and the button is pressed twice to the OFF position.
If Engine Fails T o Start W ARNING! • Never pour fuel or other flammable liquids into the throttle body air inlet opening in an attempt to start the vehicle. This could result in a flash fire causing serious personal injury . (Continued) W ARNING! (Continued) • Do not attempt to push or tow your vehicle to get it started.
Clearing a Flooded Engine (Using ENGINE ST AR T/STOP Button) – Automatic T ransmission Only If the engine fails to start after you have followed the “Normal Starting” or “Extreme Cold W eather ⬙ proce- dures, it may be flooded.
CAUTION! T o prevent damage to the starter , wait 10 to 15 sec- onds before trying again. After Starting The idle speed is controlled automatically and it will decrease as the engine warms up. ENGINE BLOCK HEA TER — IF EQUIPPED The engine block heater warms the engine, and permits quicker starts in cold weather .
CAUTION! • Never drive with your foot resting on the clutch pedal, or try to hold the vehicle on a hill with the clutch pedal partially engaged, as this will cause abnormal wear on the clutch. Refer to “Electronic Brake Control System/Hill Start Assist” in “Start- ing and Operating” for further information.
The six-speed manual transmission has a spring that centers the shift lever near third and fourth gear . This spring helps you know which gear you are in when you are shifting. Be car eful when shifting from first to second or downshifting from sixth to fifth.
NOTE: • Y our vehicle is equipped with a transmission reverse inhibitor system. When vehicle speed is greater than 3 mph (5 km/h), the reverse inhibitor activates to help prevent shifts into REVERSE.
Downshifting T o maintain a safe speed and prolong brake life, down- shift to maintain a safe speed when descending a steep grade. W ARNING! Skipping more than one gear while downshifting, could cause you to lose control of your vehicle. Y ou could have an accident.
W ARNING! It is dangerous to move the shift lever out of P ARK or NEUTRAL if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in reverse. Y ou could lose control of the vehicle and hit someone or something.
• The electronically-contr olled transmission provides a precise shift schedule. The transmission electr onics are self-calibrating. Therefor e, the first few shifts on a new vehicle may be somewhat abrupt or soft until after the break-in period. This is a normal condition, and pr e- cision shifts will develop within a few shift cycles.
This may result in a slightly dif ferent feeling or r esponse during normal operation in DRIVE position. After the transmission cools down, it will return to normal operation.
4. Using the screwdriver , press and hold the override tab through the access port on the center console. 5. Move the shift lever into the NEUTRAL position. 6. The vehicle may then be started in NEUTRAL. 7. Reinstall the override cover . W ith Keyless Go™ – If Equipped If the engine is running, pr ess the ST AR T/STOP button to turn it off.
Five-Speed Automatic T ransmission Shifting from DRIVE to P ARK or REVERSE should be done only after the accelerator pedal is released and the vehicle is stopped. Be sure to keep your foot on the brake pedal when moving the shift lever between these gears.
W ARNING! Never use the P ARK position as a substitute for the parking brake. Always apply the parking brake fully when parked to guard against vehicle movement and possible injury or damage.
CAUTION! Coasting the vehicle or driving for any other reason with the shift lever in NEUTRAL can result in transmission damage. W ARNING! Do not coast in NEUTRAL and never turn of f the ignition to coast down a hill. These are unsafe practices that limit your response to changing traffic or road conditions.
T emporary T ransmission Limp Home Mode The transmission is monitored for abnormal conditions. If a condition is detected that could result in transmission damage, the transmission will engage Limp Home Mode. If vehicle acceleration worsens or the transmission no longer shifts, the transmission is most likely operating in the Limp Home Mode.
AUTOSTICK 姞 — IF EQUIPPED AutoStick 姞 — 3.5L Engine AutoStick 威 allows you to move the shift lever to the left (-) or right (+) when the shift lever is in the DRIVE position, this allows the selection of the desired top gear .
Operation When the shift lever is in the DRIVE position, the transmission will operate automatically , shifting between the five available gears. T o engage AutoStick 威 , simply move the shift lever to the right or left (D+/D-) while in the DRIVE position.
• A void using speed control when AutoStick 威 is en- gaged. • The transmission will automatically shift up when maximum engine speed is reached while AutoStick 威 is engaged. • T ransmission shifting will be more crisp/abrupt when AutoStick 威 is engaged.
2. Slow down if the road has standing water or puddles. 3. Replace tires when tread wear indicators first become visible. 4. Keep tires properly inflated. 5. Maintain sufficient distance between your vehicle and the vehicle in front of you to avoid a collision in a sudden stop.
CAUTION! • Always check the depth of the standing water before driving through it. Never drive through standing water that is deeper than the bottom of the tire rims mounted on the vehicle.
W ARNING! • Driving through standing water limits your vehi- cle’ s traction capabilities. Do not exceed 5 mph (8 km/h) when driving through standing water . • Driving through standing water limits your vehi- cle’ s braking capabilities, which increases stop- ping distances.
W ARNING! Continued operation with reduced power steering assist could pose a safety risk to yourself and others. Service should be obtained as soon as possible. CAUTION! Prolonged operation of the steering system at the end of the steering wheel travel will increase the steering fluid temperature and it should be avoided when possible.
If necessary , add fluid to restore to the pr oper indicated level. W ith a clean cloth, wipe any spilled fluid from all surfaces. Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Y our V ehicle” for further information.
Manual T ransmission – If Equipped The foot operated parking brake is positioned below the lower left corner of the instrument panel. T o release the parking brake, pull the parking brake release handle. Automatic T ransmission – If Equipped The foot operated parking brake is located below the lower left corner of the instrument panel.
W ARNING! • Never use the P ARK position as a substitute for the parking brake. Always apply the parking brake fully when parked to guard against vehicle movement and possible injury or damage. • Never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons.
W ARNING! (Continued) • Always fully apply the parking brake when leav- ing your vehicle, or it may roll and cause damage or injury . Also be certain to leave the transmission in P ARK. Failure to do so may allow the vehicle to roll and cause damage or injury .
Anti-Lock Brake System (ABS) — If Equipped The Anti-Lock Brake System (ABS) provides incr eased vehicle stability and brake performance under most braking conditions. The system automatically “pumps” the brakes during severe braking conditions to pr event wheel lock-up.
W ARNING! • The Anti-Lock Brake System (ABS) contains so- phisticated electronic equipment that may be sus- ceptible to interference caused by improperly in- stalled or high output radio transmitting equipment. This interference can cause possible loss of anti-lock braking capability .
All vehicle wheels and tires must be the same size and type and tires must be pr operly inflated to produce accurate signals for the computer . Anti-Lock Brake W arning Light The “Anti-Lock Brake System (ABS) W arning Light” monitors the Anti-Lock Brake System.
An additional electronic brake contr ol feature called Hill Start Assist (HSA) is standard on manual transmission models. Anti-Lock Brake System (ABS) – If Equipped This system aids the driver in maintaining vehicle control under adverse braking conditions by controlling hydrau- lic brake pressur e.
A feature of the TCS system functions similar to a limited-slip differ ential (LSD) and controls the wheel spin across a driven axle. If one wheel on a driven axle is spinning faster than the other , the system will apply the brake of the spinning wheel.
Hill Start Assist (HSA) – Manual T ransmission Only The HSA system is designed to assist the driver when starting a vehicle from a stop on a hill. HSA will maintain the level of brake pressur e the driver applied for a short period of time after the driver takes their foot off of the brake pedal.
For vehicles not equipped with the EVIC, perform the following steps: NOTE: Y ou must complete Steps 1 through 8 within 90 seconds. 1. Center the steering wheel (front wheels pointing straight forward). 2. Shift the transmission into NEUTRAL. 3. Apply the parking brake.
The ESP uses sensors in the vehicle to determine the path that the driver intends to steer the vehicle and compares it to the actual path of the vehicle. When the actual path does not match the intended path, the ESP applies the brake of the appropriate wheel to assist in counteracting the condition of oversteer or understeer .
The ESP system has two available operating modes: ESP On This is the normal operating mode for the ESP . Whenever the vehicle is started, the ESP system will be in this mode. This mode should be used for most driving situations. The ESP should only be turned OFF for specific r easons as noted in the following paragraphs.
NOTE: T o improve the vehicle’s traction when driving with snow chains, or when starting off in deep snow , sand, or gravel, it may be desirable to switch to the “Partial Off” mode by momentarily pr essing the “ESP OFF” switch.
NOTE: • The “ESP/TCS Indicator Light” and the “ESP/BAS Malfunction Indicator Light” will turn on momen- tarily each time the ignition switch is turned ON. • Each time the ignition is turned ON, the ESP System will be ON even if it was turned OFF previously .
NOTE: • P (Passenger) - Metric tir e sizing is based on U.S. design standards. P-Metric tir es have the letter “P” molded into the sidewall preceding the size designa- tion. Example: P215/65R15 95H. • European-Metric tir e sizing is based on European design standards.
T ire Sizing Chart TIRE SIZING TERMS Size Designation: P = Passenger Car tire size based on U.S. design standar ds ⴖ ....blank.... ⴖ = Passenger Car tire based on Eur opean design standards LT = Light T ruck tire based on U.
TIRE SIZING TERMS Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a ti.
T ire Identification Number (TIN) The TIN may be found on one or both sides of the tire, however , the date code may only be on one side. T ires with white sidewalls will have the full TIN, including the date code, located on the white sidewall side of the tire.
Tire T erminology and Definitions T erm Definition B-Pillar The vehicle B-Pillar is a structural member of the body located between the front and r ear door (of a four-door vehicle) r unning from the sill to the r oof.
Tire Loading and T ire Pressure T ire Placard Location NOTE: The proper cold tir e inflation pressur e is listed on the driver’s side B-Pillar . T ire and Loading Information Placard This placard te.
NOTE: Under a maximum loaded vehicle condition, gross axle weight ratings (GA WRs) for the front and rear axles must not be exceeded. For further information on GA WRs, vehicle loading, and trailer towing, refer to “V ehicle Loading” in this section.
5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4. 6. If your vehicle will be towing a trailer , load from your trailer will be transferred to your vehicle.
290 ST ARTING AND OPERA TING.
W ARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle.
W ARNING! (Continued) • Unequal tire pressures from one side of the ve- hicle to the other can cause the vehicle to drift to the right or left. • Always drive with each tire inflated to the recom- mended cold tire inflation pressure. Economy Improper inflation pr essures can cause uneven wear patterns to develop across the tir e tread.
CAUTION! After inspecting or adjusting the tire pressure, al- ways reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressur es specified on the placard ar e always “cold tire inflation pr essure.
T ire Pressures for High Speed Operation The manufacturer advocates driving at safe speeds within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high speeds, maintaining correct tir e inflation pressur e is very important.
W ARNING! T emporary use spare tires are for emergency use only . W ith these tires, do not drive more than 50 mph (80 km/h). T emporary use spare tires have limited tread life. When the tread is worn to the tread wear indicators, the temporary use spare tire needs to be replaced.
W ARNING! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause tire dam- age or failure. A tire could explode and injure some- one.
Life Of Tire The service life of a tire is dependent upon varying factors including, but not limited to: • Driving style • T ire pressur e • Distance driven W ARNING! T ires and the spare tire should be replaced after six years, regardless of the remaining tread.
W ARNING! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change sus- pension dimensions and performance characteris- tics, resulting in changes to steering, handling, and braking of your vehicle.
The 245/45 R20 size tires do not pr ovide adequate clearance for tire chains. NOTE: Do not use tire chains on a compact spar e tire. CAUTION! T o avoid damage to your vehicle or tires, observe the fol.
NOTE: In order to avoid damage to tir es, chains, and your vehicle do not drive for a prolonged period on dry pavement. Observe the tire chain manufactur er’s instruc- tions on method of installation, operating speed, and conditions for usage.
permissible if desired. Also, correct for anything causing rapid or unusual wear prior to performing the tire rotation. The suggested rotation method for vehicles equipped with all season tires is the “forwar d-cross” as shown in the following diagram.
The TPMS will warn the driver of a low tire pr essure if the tire pr essure falls below the low-pr essure warning limit for any reason, including low temperatur e effects and natural pressur e loss through the tir e.
CAUTION! • The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when us- ing replacement equipment that is not of the same size, type, and/or style.
• Seasonal temperature changes will af fect tire pr essure, and the TPMS will monitor the actual tire pr essure in the tire. Base System The T ire Pressur e Monitor System (TPMS) uses wireless technology with wheel rim mounted electronic sensors to monitor tire pr essure levels.
turn off when the fault condition no longer exists. A system fault can occur due to any of the following: 1. Signal interference due to electronic devices or driving next to facilities emitting the same radio frequencies as the TPM sensors. 2. Installing aftermarket window tinting that contains materials that may block radio wave signals.
Premium System – If Equipped The T ire Pressur e Monitor System (TPMS) uses wireless technology with wheel rim mounted electronic sensors to monitor tire pr essure levels. Sensors mounted to each wheel as part of the valve stem transmit tire pr essure readings to the r eceiver module.
T ire Pressure Monitoring Low Pressure W arnings The “TPM T elltale Light” will illuminate in the instrument cluster and a chime will sound when tire pr essure is low in one or mor e of the four active road tir es.
will turn off. The vehicle may need to be driven for up to 20 minutes above 15 mph (25 km/h) in order for the TPMS to receive this information. Check TPMS W arning If a system fault is detected, the “TPM T elltale Light” will flash on and off for 75 seconds and then r emain on solid.
If the ignition switch is cycled, this sequence will repeat, providing the system fault still exists. If the system fault no longer exists, the “TPM T elltale Light” will no longer flash, and the ⬙ CHECK TPM SYSTEM ⬙ message will no longer display , and a pressure value will display in place of the dashes.
4. For each subsequent ignition switch cycle, a chime will sound, the “TPM T elltale Light” will flash on and off for 75 seconds and then remain on solid, and the EVIC will display a ⬙ CHECK TPM SYSTEM ⬙ message for three seconds and then display dashes (- -) in place of the pressur e value.
FUEL REQUIREMENTS 3.5L and 5.7L Engine (with Automatic T ransmission) The 3.5L and 5.7L engine (with automatic transmission) is designed to meet all emis- sions regulations and pr ovide satisfactory fuel economy and performance when us- ing high-quality unleaded gasoline having an octane range of 87 to 89.
Reformulated Gasoline Many areas of the country r equire the use of cleaner burning gasoline referr ed to as “reformulated gasoline.” Reformulated gasolines contain oxygenates and are spe- cifically blended to reduce vehicle emissions and im- prove air quality .
If a Non-FFV vehicle is inadvertently fueled with E-85 fuel, the engine will have some or all of these symptoms: • operate in a lean mode • OBD II “Malfunction Indicator Light” on • poor eng.
Materials Added to Fuel All gasoline sold in the United States is requir ed to contain effective deter gent additives. Use of additional detergents or other additives is not needed under normal conditions and they would result in additional cost. Therefor e, you should not have to add anything to the fuel.
Carbon Monoxide W arnings W ARNING! Carbon monoxide (CO) in exhaust gases is deadly . Follow the precautions below to prevent carbon monoxide poisoning: • Do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas, which can kill.
ADDING FUEL Fuel Filler Cap (Gas Cap) The gas cap is located behind the fuel filler door on the left side of the vehicle. Use a finger to pull open the door . If the gas cap is lost or damaged, be sure the r eplacement cap is for use with this vehicle.
CAUTION! • Damage to the fuel system or emissions control system could result from using an improper fuel tank filler tube cap (gas cap). • A poorly fitting gas cap could let impurities into the fuel system. • A poorly fitting gas cap may cause the “Malfunc- tion Indicator Light (MIL)” to turn on.
Loose Fuel Filler Cap Message If the vehicle diagnostic system determines that the fuel filler cap is loose, improperly installed, or damaged, a ”gASCAP” message will display in the odometer or a “Check Gascap” message will display in the Electronic V ehicle Information Center (EVIC) (if equipped).
• T ype of V ehicle • Month Day and Hour of Manufacture (MDH) The bar code allows a computer scanner to read the VIN. Gross V ehicle Weight Rating (GVWR) The GVWR is the total allowable weight of your vehicle. This includes driver , passengers, and cargo.
Figure out the weight on the fr ont and rear of the vehicle separately . It is important that you distribute the load evenly over the front and r ear axles. Overloading can cause potential safety hazards and shorten useful service life. Heavier axles or suspension components do not necessarily increase the vehicle’s GVWR.
Common T owing Definitions The following trailer towing related definitions will assist you in understanding the following information: Gross V ehicle W eight Rating (GVWR) The GVWR is the total allowable weight of your vehicle. This includes driver , passengers, cargo, and tongue weight.
T ongue W eight (TW) The TW is the downward for ce exerted on the hitch ball by the trailer . In most cases, it should not be less than 10% or more than 15% of the trailer load. Y ou must consider this as part of the load on your vehicle. Frontal Area The frontal ar ea is the maximum height and maximum width of the front of a trailer .
W ARNING! • An improperly adjusted weight distributing hitch system may reduce handling, stability , braking performance, and could result in an accident.
T railer T owing Weights (Maximum T railer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/T ransmission Frontal Area Max. GTW (Gross T railer Wt.) Max. T ongue Wt. 3.5L Automatic 12 sq ft (1.
Consider the following items when computing the weight on the rear axle of the vehicle: • The tongue weight of the trailer . • The weight of any other type of cargo or equipment put in or on your vehicle. • The weight of the driver and all passengers.
W ARNING! (Continued) • Make certain that the load is secured in the trailer and it will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that may be difficult for the driver to control. Y ou could lose control of your vehicle and have an accident.
W ARNING! (Continued) 4. T ongue weight rating for the trailer hitch utilized. (This requirement may limit the ability to always achieve the 10% to 15% range of tongue weight as a percentage of total trailer weight.) T owing Requirements – T ires − Do not attempt to tow a trailer while using a compact spare tir e.
− An electronically actuated trailer brake contr oller is requir ed when towing a trailer with electronically actuated brakes. When towing a trailer equipped with a hydraulic surge actuated brake system, an electr onic brake controller is not r equired.
T owing Requirements – T railer Lights and Wiring Whenever you pull a trailer , regar dless of the trailer size, stoplights and turn signals on the trailer are r equired for motoring safety . The T railer T ow Package may include a four- and seven- pin wiring harness.
T owing Tips Before setting out on a trip, practice turning, stopping, and backing up the trailer in an area located away fr om heavy traffic. Automatic T ransmission The DRIVE range can be selected when towing. How- ever , if frequent shifting occurs while in this range, use the AutoStick 威 mode to select a lower gear range.
Electronic Speed Control – If Equipped − Do not use in hilly terrain or with heavy loads. − When using the speed control, if you experience speed drops gr eater than 10 mph (16 km/h), disengage until you can get back to cruising speed. − Use speed control in flat terrain and with light loads to maximize fuel efficiency .
RECREA TIONAL TOWING (BEHIND MOTORHOME, ETC.) Recreational towing is allowed ONL Y if the driveshaft is removed. T owing with the rear wheels on the ground while the driveshaft is connected can result in sever e transmission damage.
WHA T T O DO IN EMERGENCIES CONTENTS 䡵 Hazard W arning Flasher ................ 3 3 5 䡵 If Y our Engine Overheats ................ 3 3 5 䡵 TIREFIT Kit — If Equipped .............. 3 3 6 ▫ TIREFIT Storage ..................... 3 3 7 ▫ TIREFIT Kit Components And Operation .
䡵 T owing A Disabled V ehicle ............... 3 6 2 ▫ W ithout The Key FOB ................. 3 6 2 ▫ T owing This V ehicle Behind Another V ehicle (Flat T owing W ith All Four Wheels On The Ground) ........................... 3 6 2 ▫ T owing This V ehicle Behind Another V ehicle W ith A T ow Dolly .
HAZARD W ARNING FLASHER The Hazard W arning flasher switch is located in the switch bank near the bottom center of the instrument panel. Press the switch to turn on the Hazar d W arning flasher . When the switch is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emer gency .
CAUTION! Driving with a hot cooling system could damage your vehicle. If the temperature gauge reads 240°F (1 16 °C) or greater pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range 200– 230°F (93–1 10°C).
This kit will provide a temporary tir e seal, allowing you to drive your vehicle up to 100 miles (160 km) with a maximum speed of 55 mph (88 km/hr). TIREFIT Storage The TIREFIT kit is located in the trunk. TIREFIT Kit Components and Operation 1. Sealant Bottle 2.
5. Power Plug and Cable 6. Air Pump Hose (Black) 7. Sealant Hose (Clear with Y ellow Cap) 8. Accessory Storage Compartment Using the Mode Select Knob and Hoses Selecting Air Mode T urn the Mode Select knob (4) to this position for air pump operation only .
the vehicle or tire and wheel components. Once the sealant dries, it can easily be peeled off and pr operly discarded. • For optimum performance, make sure the valve stem on the wheel is free of debris befor e connecting the TIREFIT kit. • Y ou can use the TIREFIT air pump to inflate bicycle tires.
W ARNING! (Continued) − If you are unsure of the condition of the tire or the wheel. • Keep TIREFIT away from open flame or heat source. • A loose TIREFIT kit thrown forward in a collision or hard stop could endanger the occupants of the vehicle.
Sealing a Tire with TIREFIT (A) Whenever Y ou Stop to Use TIREFIT : 1. Pull over to a safe location and turn ON the vehicle’s Hazard W arning flashers. 2. V erify that the valve stem (on the wheel with the deflated tire) is in a position that is near to the gr ound.
(C) Injecting TIREFIT Sealant into the deflated tire: • Always start the engine before turning ON the TIRE- FIT kit. NOTE: Manual transmission vehicles must have the parking brake engaged and the shifter in NEUTRAL.
If the sealant (white fluid) does flow through the clear Sealant Hose (7): 1. Continue to operate pump until sealant is no longer flowing through hose (typically takes 30 - 70 seconds). As the sealant flows through hose (7), the pr essure gauge (2) can read as high as 70 psi (5 Bar).
CAUTION! • The metal end fitting from Power Plug and Cable (5) may get hot after use, so should be handled carefully . • Failure to reinstall the Y ellow Cap on the fitting at the end of the Clear Sealant Hose (7) can result in sealant contacting your skin, clothing, and the vehicle’ s interior .
If tire pressure is less than 19 psi (1.3 Bar) , the tire is too badly damaged. Do not attempt to drive the vehicle further . Call for assistance. If the tire pressure is 19 psi (1.
4. Clean any remaining sealant from the TIREFIT hous- ing. 5. Position the new Sealant Bottle (1) to the housing so that the Clear Sealant Hose (7) aligns with the hose slot in the front of the housing and the alignment keys on the bottom of the bottle align with the alignment slots in the housing.
W ARNING! (Continued) • The jack is designed to use as a tool for changing tires only . The jack should not be used to lift the vehicle for service purposes.
3. Remove the fastener securing the spare tire. 4. Remove the spare tire. 5. Remove the fastener securing the jack. W ARNING! A loose tire or jack thrown forward in a collision or hard stop could endanger the occupants of the ve- hicle. Always stow the jack parts and the spare tire in the places provided.
Preparations For Jacking 1. Park the vehicle on a firm, level surface as far from the edge of the roadway as possible. A void icy or slippery areas. W ARNING! Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough of f the road to avoid being hit when operating the jack or changing the wheel.
W ARNING! (Continued) • Always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle. • Block the wheel diagonally opposite the wheel to be raised. • Set the parking brake firmly and set an automatic transmission in P ARK; a manual transmission in REVERSE.
2. If equipped with steel wheels, do not remove the wheel cover at this time. If equipped with aluminum wheels where the center cap covers the lug nuts, use the lug wrench to pry the center cap of f carefully befor e raising the vehicle.
3. Before raising the vehicle, use the lug wrench to loosen, but not remove, the lug nuts on the wheel with the flat tire. T urn the lug nuts counterclockwise one turn while the wheel is still on the ground. 4. Place the jack underneath the lift area that is closest to the flat tire.
W ARNING! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 6. Remove the lug nuts, wheel cover (if equipped), and tire. Remove the cover by hand.
W ARNING! A loose tire or jack thrown forward in a collision or hard stop could endanger the occupants of the ve- hicle. Always stow the jack parts and the spare tire in the places provided. Compact Spare Tire The compact spare tir e is for temporary emergency use with radial tires.
Wheel Cover or Center Cap Installation — If Equipped NOTE: Do not attempt to install a center cap or wheel cover on the compact spare. 1. Mount the road tire on the axle. For vehicles equipped with wheel covers, perform Steps 2 and 3. For vehicles equipped with center caps, proceed to Step 4.
3. Align the valve notch in the wheel cover with the valve stem on the wheel. Install the cover by hand, snapping the cover over the two lug nuts. Do not use a hammer or excessive force to install the cover . 4. Install the remaining lug nuts with the cone shaped end of the nut toward the wheel.
JUMP-ST ARTING PROCEDURES If your vehicle has a discharged battery it can be jump- started using a set of jumper cables and a battery in another vehicle or by using a portable battery booster pack. Jump-starting can be dangerous if done impr operly so please follow the procedur es in this section carefully .
Remote Battery Posts W ARNING! • T ake care to avoid the radiator cooling fan when- ever the hood is raised. It can start anytime the ignition switch is on. Y ou can be injured by moving fan blades. • Remove any metal jewelry such as watch bands or bracelets that might make an inadvertent electrical contact.
3. If using a another vehicle to jump-start the battery , park the vehicle within the jumper cables reach, set the parking brake and make sure the ignition is OFF . W ARNING! Do not allow vehicles to touch each other as this could establish a ground connection and personal injury could result.
W ARNING! Do not connect the cable to the negative post (-) of the discharged battery . The resulting electrical spark could cause the battery to explode and could result in personal injury .
FREEING A STUCK VEHICLE If your vehicle becomes stuck in mud, sand, or snow , it can often be moved by a rocking motion. T urn your steering wheel right and left to clear the area ar ound the front wheels. Then shift back and forth between RE- VERSE and DRIVE.
W ARNING! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause damage, or even failure, of the axle and tires. A tire could explode and injure someone.
If the transmission is not operative or if the vehicle is to be towed more than 15 miles (24 km) or faster than 30 mph (48 km/h), the vehicle must be transported using a flatbed truck. CAUTION! • Do not attempt to tow this vehicle from the front with sling-type towing equipment.
.
MAINT AINING YOUR VEHICLE CONTENTS 䡵 Engine Compartment — 3.5L ............. 3 6 8 䡵 Engine Compartment — 5.7L ............. 3 6 9 䡵 Onboard Diagnostic System — OBD II ...... 3 7 0 ▫ Loose Fuel Filler Cap ................. 3 7 0 䡵 Emissions Inspection And Maintenance Programs .
▫ Cooling System ..................... 3 8 6 ▫ Brake System ....................... 3 9 1 ▫ Clutch Hydraulic System – Manual T ransmission (If Equipped) ............. 3 9 4 ▫ Manual T ransmission – If Equipped ....... 3 9 4 ▫ Automatic T ransmission – If Equipped .
䡵 Fluids, Lubricants, And Genuine Parts ....... 4 1 6 ▫ Engine ............................ 4 1 6 ▫ Chassis ........................... 4 1 7 7 MAINT AINING YOUR VEHICLE 367.
ENGINE COMP ARTMENT — 3.5L 1 — Integrated Power Module 6 — Engine Oil Fill 2 — Air Cleaner Filter 7 — Engine Oil Dipstick 3 — Brake Fluid Reservoir Access Cover 8 — Remote Jump Start (Po.
ENGINE COMP ARTMENT — 5.7L 1 — Integrated Power Module 6 — Air Cleaner Filter 2 — Coolant Pressur e Cap 7 — Engine Oil Fill 3 — Brake Fluid Reservoir Access Cover 8 — Engine Oil Dipstick.
ONBOARD DIAGNOSTIC SYSTEM — OBD II Y our vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems.
T rip Odometer button to turn off the message. If the problem continues, the message will appear the next time the vehicle is started. A loose, improperly installed, or damaged fuel filler cap may also turn on the MIL.
5. Approximately 15 seconds later , one of two things will happen: a. The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition key or start the engine. This means that the vehicle’s OBD II system is not ready and you should not proceed to the I/M station.
DEALER SERVICE Y our authorized dealer has the qualified service person- nel, special tools, and equipment to perform all service operations in an expert manner . Service manuals are available which include detailed service information for your vehicle.
CAUTION! (Continued) • Y our vehicle has been built with improved fluids that protect the performance and durability of your vehicle and also allow extended maintenance intervals. Do not use chemical flushes in these components as the chemicals can damage your engine, transmission, power steering or air condi- tioning.
regular intervals, such as every fuel stop. The best time to check the engine oil level is about five minutes after a fully warmed engine is shut off. Checking the oil while the vehicle is on level ground will improve the accuracy of the oil level r eadings.
CAUTION! Do not use chemical flushes in your engine oil as the chemicals can damage your engine. Such damage is not covered by the New V ehicle Limited W arranty . Engine Oil V iscosity (SAE Grade) – 3.5L Engine SAE 10W -30 engine oil is preferred for for all operating temperatures.
Synthetic Engine Oils Y ou may use synthetic engine oils provided the recom- mended oil quality requir ements are met, and the r ecom- mended maintenance intervals for oil and filter changes are followed. Materials Added to Engine Oil Do not add any supplemental materials, other than leak detection dyes, to the engine oil.
Engine Air Cleaner Filter Refer to “Maintenance Schedule” for further information. W ARNING! The air induction system (air cleaner , hoses, etc.) can provide a measure of protection in the case of engine backfire. Do not remove the air induction system (air cleaner , hoses, etc.
W ARNING! • Battery fluid is a corrosive acid solution and can burn or even blind you. Do not allow battery fluid to contact your eyes, skin, or clothing. Do not lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area imme- diately with large amounts of water .
W ARNING! (Continued) • The battery in this vehicle has a vent hose that should not be disconnected and should only be replaced with a battery of the same type (vented).
W ARNING! • Use only refrigerants and compressor lubricants approved by the manufacturer for your air condi- tioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs.
hood latching components to ensure pr oper function. When performing other underhood services, the hood latch, release mechanism and safety catch should be cleaned and lubricated. The external lock cylinders should be lubricated twice a year , preferably in the Fall and Spring.
When refilling the washer fluid r eservoir , apply some washer fluid to a cloth or towel and wipe the wiper blades clean. This will help blade performance. T o prevent freeze-up of your windshield washer system in cold weather , select a solution or mixture that meets or exceeds the temperature range of your climate.
W ARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. T o avoid breathing CO, refer to “Safety T ips/Exhaust Gas” in “Things T o Know Before Starting Y our V ehicle” for further informa- tion.
NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you. W ARNING! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your exhaust system.
Cooling System W ARNING! • When working near the radiator cooling fan, dis- connect the fan motor lead or turn the ignition switch to the LOCK position (OFF position for Keyless Go™). The fan is temperature controlled and can start at any time the ignition switch is in the ON position (RUN position for Keyless Go™).
Cooling System – Drain, Flush, and Refill If the engine coolant (antifreeze) is dirty or contains a considerable amount of sediment, clean and flush with a reliable cooling system cleaner . Follow with a thorough rinsing to remove all deposits and chemicals.
CAUTION! (Continued) • This vehicle has not been designed for use with propylene glycol-based engine coolant (anti- freeze). Use of propylene glycol-based engine coolant (antifreeze) is not recommended. Adding Coolant Y our vehicle has been built with an improved engine coolant (antifreeze) that allows extended maintenance intervals.
NOTE: Mixing engine coolant (antifreeze) types will decrease the life of the engine coolant (antifr eeze) and will requir e more fr equent engine coolant (antifreeze) changes.
Disposal of Used Coolant Used ethylene glycol-based engine coolant (antifreeze) is a regulated substance r equiring proper disposal. Check with your local authorities to determine the disposal rules for your community .
If an examination of your engine compartment shows no evidence of radiator or hose leaks, the vehicle may be safely driven. The vapor will soon dissipate. • Do not overfill the coolant recovery bottle. • Check engine coolant (antifreeze) fr eeze point in the radiator and in the coolant recovery bottle.
W ARNING! Riding the brakes can lead to brake failure and possibly an accident. Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear , and possible brake damage. Y ou would not have your full braking capacity in an emergency .
W ARNING! • Use only manufacturer’s recommended brake fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Y our V ehicle” for further information. Using the wrong type of brake fluid can severely damage your brake system and/or impair its performance.
W ARNING! (Continued) • Do not allow petroleum based fluid to contami- nate the brake fluid. Brake seal components could be damaged, causing partial or complete brake failure.
Automatic T ransmission – If Equipped Fluid Level Check Regular automatic transmission fluid level checks are not requir ed. For this reason, the dipstick is omitted. If you notice fluid loss or gear shift malfunction, have your authorized dealer check the transmission fluid level.
Selection of Lubricant It is important that the proper lubricant is used in the transmission to assure optimum transmission perfor - mance. Use only manufacturer ’s recommended transmis- sion fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Y our V ehicle” for further informa- tion.
Appearance Care and Protection from Corrosion Protection of Body and Paint from Corrosion V ehicle body care requir ements vary according to geo- graphic locations and usage.
• Use a high quality cleaner wax, such as MOP AR 威 Cleaner W ax or equivalent, to remove road film, stains and to protect your paint finish. T ake care never to scratch the paint. • A void using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish.
• Use MOP AR 威 T ouch Up Paint or equivalent on scratches as soon as possible. Y our authorized dealer has touch up paint to match the color of your vehicle. Wheel and Wheel T rim Care All wheels and wheel trim, especially aluminum and chrome-plated wheels should be cleaned r egularly with a mild soap and water to prevent corr osion.
Interior Care Use MOP AR 威 Fabric Cleaner or equivalent to clean fabric upholstery and MOP AR 威 Carpet Cleaner or equivalent for carpeting. Interior T rim should be cleaned starting with a damp cloth, or MOP AR 威 Satin Select or equivalent. Do not use harsh cleaners or Armor All 威 .
Do not use abrasive cleaning components, solvents, steel wool or other aggressive material to clean the lenses. Glass Surfaces All glass surfaces should be cleaned on a regular basis with MOP AR 威 Glass Cleaner or equivalent, or any com- mercial household-type glass cleaner .
NOTE: The cupholder cannot be removed. FUSES Integrated Power Module (IPM) The Integrated Power Module (IPM) is located in the engine compartment. This module contains fuses and relays. CAUTION! • When installing the integrated power module cover , it is important to ensure the cover is prop- erly positioned and fully latched.
Cavity Car- tridge Fuse Mini- Fuse Description 1 — 15 Amp Blue W asher Motor 2 — 25 Amp Natural Powertrain Control Module (PCM) 3 — 25 Amp Natural Ignition Run/Start 4 — 25 Amp Natural EGR Sol.
Cavity Car- tridge Fuse Mini- Fuse Description 1 9——— 2 0——— 2 1——— 2 2——— Rear Power Distribution Center There is also a power distribution center located in the trunk under the spar e tire access panel. This center contains fuses and relays.
CAUTION! • When installing the power distribution center cover , it is important to ensure the cover is prop- erly positioned and fully latched. Failure to do so may allow water to get into the power distribution center and possibly result in an electrical system failure.
Cavity Car- tridge Fuse Mini- Fuse Description 1 60 Amp Y ellow — Ignition Off Draw (IOD) Cavity 1 of the Rear Power Distribution Center contains a black IOD fuse needed for vehicle processing dur- ing assembly . The ser- vice replacement part is a 60 Amp yellow car- tridge fuse.
Cavity Car- tridge Fuse Mini- Fuse Description 13 * ——— 14 — 10 Amp Red AC Heater Control/ Cluster/Security Mod- ule – If Equipped 1 5——— 1 6——— 17 — 20 Amp Y ellow Cluster 18 .
Cavity Car- tridge Fuse Mini- Fuse Description 30 — 10 Amp Red Door Modules/Power Mirrors/Steering Con- trol Module (SCM) 3 1——— 3 2——— 3 3——— 3 4——— 35 — 5 Amp Orange Ante.
* Cavities 1 1, 12, and 13 contain self-resetting fuses (circuit br eakers) that are only serviceable by an autho- rized dealer . The cluster and the driver seat switch are fused by the 25 Amp circuit br eaker in cavity 1 1. The passenger seat switch is fused by the 25 Amp circuit breaker in cavity 12.
All of the interior bulbs are glass wedge base or glass cartridge types. Aluminum base bulbs are not approved and should not be used for replacement. LIGHT BULBS – Exterior Bulb Number Low Beam Headlamp – High Intensity Discharge (HID) .......... D 1 S (Serviced at Authorized Dealer) High Beam Headlamp .
W ARNING! A transient high tension occurs at the bulb sockets of HID headlamps when the headlamp switch is turned ON. It may cause serious electrical shock or electro- cution if not serviced properly .
T ail/T urn and Stop Lamp 1. Open the trunk. 2. Using a screwdriver , remove the tail lamp r etainer . 3. Remove the fasteners from the back of the tail lamp assembly . 4. Pull back the trunk liner . 5. Remove the remaining fasteners from the back of the tail lamp assembly .
7. Push the electrical connector locking tab to the side. 8. Disconnect the electrical connector . 9. T urn the appropriate bulb and socket assembly coun- terclockwise to r emove it from the tail lamp assembly . 10. Disconnect the bulb from the socket assembly and install the replacement bulb.
Center T ail/Backup Lamp See your authorized dealer for bulb replacement. Center High-Mounted Stop Lamp (CHMSL) The CHMSL uses LED lamps that are not serviceable separately . The CHMSL must be r eplaced as an assembly , see your authorized dealer . License Lamp 1.
FLUID CAP ACITIES U.S. Metric Fuel (Approximate) 3.5 Liter Engine 18.5 Gallons 70 Liters 5.7 Liter Engine 19 Gallons 72 Liters Engine Oil with Filter 3.5 Liter Engine (SAE 10W -30, API Certified) 6 Quarts 5.7 Liters 5.7 Liter Engine (SAE 5W -20, API Certified) 7 Quarts 6.
FLUIDS, LUBRICANTS, AND GENUINE P ARTS Engine Component Fluid, Lubricant, or Genuine Part Engine Coolant MOP AR 威 Antifreeze/Coolant 5 Y ear/100,000 Mile Formula HOA T (Hy- brid Organic Additive T echnology) or equivalent.
Chassis Component Fluid, Lubricant, or Genuine Part Manual T ransmission – If Equipped MOP AR 威 A TF+4 威 Automatic T ransmission Fluid or equivalent licensed A TF+4 威 product. Automatic T ransmission – If Equipped MOP AR 威 A TF+4 威 Automatic T ransmission Fluid or equivalent licensed A TF+4 威 product.
.
MAINTENANCE SCHEDULES CONTENTS 䡵 Emission Control System Maintenance ...... 4 2 0 䡵 Maintenance Schedule .................. 4 2 0 ▫ Required Maintenance Intervals .
EMISSION CONTROL SYSTEM MAINTENANCE The Scheduled Maintenance services listed in bold type, must be done at the times or mileages specified to ensure the continued proper functioning of the Emission Contr ol System.
NOTE: • The oil change indicator message will not monitor the time since the last oil change. Change your vehicle’s oil if it has been six months since your last oil change, even if the oil change indicator message is NOT illuminated. • Change your engine oil more often if you drive your vehicle off-r oad for an extended period of time.
• Check the fluid levels of the coolant reservoir , brake master cylinder , and power steering, and add as needed. • Check all lights and other electrical items for correct operation. At Each Oil Change • Change the engine oil filter . • Inspect the brake hoses and lines.
6,000 Miles (10,000 km) or 6 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. Odometer Reading Date Repair Order # Dealer Code Signature Authorized Chrysler Dealer 12,000 Miles (20,000 km) or 12 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter .
18,000 Miles (30,000 km) or 18 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ Inspect the rear axle fluid.
30,000 Miles (50,000 km) or 30 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ Replace the engine air cleaner filter . ❏ Replace the spark plugs (5.7L Engine). ❏ Adjust parking brake on vehicles equipped with four-wheel disc brakes.
42,000 Miles (70,000 km) or 42 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. Odometer Reading Date Repair Order # Dealer Code Signature Authorized Chrysler Dealer 48,000 Miles (80,000 km) or 48 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter .
54,000 Miles (90,000 km) or 54 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ Inspect the rear axle fluid.
66,000 Miles (1 10,000 km) or 66 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary .
78,000 Miles (130,000 km) or 78 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary .
90,000 Miles (150,000 km) or 90 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ Replace the engine air cleaner filter . ❏ Replace the spark plugs (5.7L Engine). ❏ Inspect and replace PCV valve if necessary .
102,000 Miles (170,000 km) or 102 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary .
1 14,000 Miles (190,000 km) or 1 14 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary .
120,000 Miles (200,000 km) or 120 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ Replace the engine air cleaner filter . ❏ Replace the air conditioning filter (if equipped) ❏ Replace the spark plugs (5.
126,000 Miles (210,000 km) or 126 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary .
138,000 Miles (230,000 km) or 138 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary .
† This maintenance is recommended by the manufactur er to the owner , but is not requir ed to maintain emissions warranty . W ARNING! • Y ou can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment.
IF YOU NEED CONSUMER ASSIST ANCE CONTENTS 䡵 Suggestions For Obtaining Service For Y our V ehicle .............................. 4 3 9 ▫ Prepar e For The Appointment ........... 4 3 9 ▫ Prepar e A List ...................... 4 3 9 ▫ Be Reasonable W ith Requests .
䡵 Department Of T ransportation Uniform T ire Quality Grades ........................ 4 4 5 ▫ T readwear ......................... 4 4 5 ▫ T raction Grades .
SUGGESTIONS FOR OBT AINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sur e to have the right papers with you. T ake your warranty folder . All work to be performed may not be covered by the warranty .
This is why you should always talk to an authorized dealer’s service manager first. Most matters can be re- solved with this process. • If for some reason you ar e still not satisfied, talk to the general manager or owner of the authorized dealer- ship.
Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) T o assist customers who have hearing difficulties, the manufacturer has installed special TDD (T elecommuni- cation Devices for the Deaf) equipment at its customer center .
W e appreciate that you have made a major investment when you purchased the vehicle. An authorized dealer has also made a major investment in facilities, tools, and training to assure that you ar e absolutely delighted with the ownership experience.
If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may or der a recall and r emedy campaign. However , NHTSA cannot become involved in individual problems between you, your authorized dealer , and the manufacturer .
• Service Manuals These comprehensive Service Manuals pr ovide the infor- mation that students and professional technicians need in diagnosing/troubleshooting, pr oblem solving, main- taining, servicing, and repairing Chrysler Gr oup LLC vehicles.
DEP ARTMENT OF TRANSPORT A TION UNIFORM TIRE QUALITY GRADES The following tire grading categories wer e established by the National Highway T raffic Safety Administration. The specific grade rating assigned by the tire’s manufactur er in each category is shown on the sidewall of the tires on your vehicle.
T emperature Grades The temperature grades ar e A (the highest), B, and C, repr esenting the tire’s r esistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel.
INDEX 10.
About Y our Brakes .................... 267,270 ABS (Anti-Lock Brake System) ............ 271,274 Adding Engine Coolant (Antifreeze) .......... 3 8 8 Adding Fuel ........................... 3 1 6 Adding W asher Fluid ..................... 3 8 2 Additives, Fuel .
Automatic Headlights .................... 1 2 4 Automatic Oil Change Indicator ............. 1 6 8 Automatic T ransaxle Special Additives ...................... 3 9 6 Automatic T ransmission ................ 256,395 Adding Fluid ......................
Bulb Replacement ..................... 409,410 Bulbs, Light .......................... 72,409 Calibration, Compass ..................... 1 8 3 Capacities, Fluid ........................ 4 1 5 Caps, Filler Fuel ............................... 3 1 6 Oil (Engine) .
Connector U C I ................................ 2 1 3 Universal Consumer Interface (UCI) ......... 2 1 3 Conserving Fuel ........................ 1 7 8 Console .............................. 1 5 1 Console, Floor .......................... 1 5 1 Console, Overhead .
Power Steering ........................ 2 6 6 Disabled V ehicle T owing ................... 3 6 2 Disposal Antifreeze (Engine Coolant) ............... 3 9 0 Engine Oil ........................... 3 7 7 Door Locks ............................. 2 9 Door Locks, Automatic .
Coolant (Antifreeze) ................. 386,416 Cooling ............................. 3 8 6 Exhaust Gas Caution .................. 70,315 Fails to Start .......................... 2 4 5 Flooded, Starting ...................... 2 4 5 Fuel Requirements .
Fluid, Brake ........................... 4 1 7 Fluid Capacities ......................... 4 1 5 Fluid Leaks ............................. 7 2 Fluid Level Checks Automatic T ransmission ................. 3 9 5 Brake .............................. 3 9 2 Cooling System .
Gasoline, Clean Air ...................... 3 1 2 Gasoline (Fuel) ......................... 3 1 1 Conserving .......................... 1 7 8 Gasoline, Reformulated ................... 3 1 2 Gauges Coolant T emperature ................... 1 6 2 Fuel ..
Heater , Engine Block ..................... 2 4 7 High Beam/Low Beam Select (Dimmer) Switch . . 127 Hill Start Assist ......................... 2 7 6 Hitches T railer T owing ........................ 3 2 3 Holder , Cup ........................... 1 5 0 HomeLink 威 (Garage Door Opener) T ransmitter .
Knee Bolster ........................ 45,46,47 Lane Change and T urn Signals .............. 1 2 6 Lap/Shoulder Belts ....................... 3 7 LA TCH (Lower Anchors and T ether for CHildren) ..... 64,65 Latches ................................ 7 2 Hood .
Illuminated Entry ....................... 2 0 Instrument Cluster .................. 123,161 Intensity Control ...................... 1 2 9 Interior .......................... 129,137 License ............................. 4 1 4 Lights On Reminder .....
Maintenance Free Battery .................. 3 7 8 Maintenance, General ..................... 3 7 3 Maintenance Procedur es ................... 3 7 3 Maintenance Schedule .................... 4 2 0 Maintenance, Sunroof ..................... 1 4 7 Malfunction Indicator Light (Check Engine) .
Oil, Engine ......................... 374,416 Capacity ............................ 4 1 5 Change Interval .................... 168,375 Checking ............................ 3 7 4 Dipstick ............................. 3 7 4 Disposal ..................
Mirrors .............................. 7 9 Outlet (Auxiliary Electrical Outlet) .......... 1 4 7 Seats ............................... 1 1 4 Steering .......................... 265,266 Sunroof ............................. 1 4 4 W indows .............
Replacement T ires ....................... 2 9 7 Reporting Safety Defects ................... 4 4 2 Resetting Oil Change Indicator .............. 1 6 8 Restraint, Head ......................... 1 1 7 Restraints, Child ......................... 6 0 Restraints, Occupant .
Rear Folding ......................... 1 2 1 Seatback Release ....................... 1 2 1 T ilting .............................. 1 1 4 Security Alarm (Theft Alarm) ................ 1 8 Selection of Coolant (Antifreeze) .......... 387,416 Selection of Oil .
Remote .............................. 2 6 Starting and Operating .................... 2 3 9 Starting Procedur es ...................... 2 3 9 Steering Column Controls ...................... 1 2 6 Column Lock ......................... 1 3 2 Power .....
Air Pressur e .......................... 2 9 1 Chains .............................. 2 9 8 Changing ......................... 346,349 Compact Spare ........................ 2 9 4 Flat Changing ........................ 3 4 6 General Information .......
Hitches ............................. 3 2 3 Minimum Requirements ................. 3 2 5 T i p s ................................ 3 3 0 T railer and T ongue W eight ............... 3 2 4 W iring .............................. 3 2 9 T railer T owing Guide .
V ehicle Certification Label ................. 3 1 8 V ehicle Identification Number (VIN) ............ 6 V ehicle Loading ................... 287,318,320 V ehicle Modifications/Alterations .............. 7 V ehicle Storage ....................... 233,409 V ehicle Theft Alarm (Security Alarm) .
Chrysler Group LL C 10D 491 -126-AB 2nd Edition Printed in U.S.A..
Een belangrijk punt na aankoop van elk apparaat Dodge 2010 Challenger (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Dodge 2010 Challenger heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Dodge 2010 Challenger vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Dodge 2010 Challenger leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Dodge 2010 Challenger krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Dodge 2010 Challenger bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Dodge 2010 Challenger kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Dodge 2010 Challenger . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
