Gebruiksaanwijzing /service van het product -6D van de fabrikant DTS
Ga naar pagina of 32
DIGITAL THEATER SYSTEMS, INC. Digital Sound For Movies DTS-6 /-6D System Te sting And Troubleshooting August 1999 Digital Theater System s, Inc. 5171 Clareton Drive DTS SA, UK Agou ra Hills, CA 91301 USA Telephone: 44 (0) 118 934 9199 Telephone (818) 706-3525 Fax: 44 (0) 118 934 9198 Fax (818) 706- 1868 Email cinem atech@dtson line.
2 TABLE OF CONTENTS Pag e DTS Sy stem Test ………………………………………………………………..… 3 – 5 70mm Failsafe Test ……………………………………………………………….. 6 DTS Test Discs (history ) ………………………………………………………….
3 DTS-6/6D System T est Tools Required ** RTA ( real time an alyzer ) and pink noise card. Neces sary to adjust EQ in “ B” chain. ** SPL meter Projector Speed Disc ( special order f rom DTS ) DTS Technician’s Kit : • • • • 6-Track SETUP Dis c, Rev.
4 DTS SYSTEM TEST 6. Index Switch. A small black momentary push button switch located below the TIMECODE HEAD OFFSET switches (behind the plate and under the LED s). I t is commonly called the “index switch”. This button can be used to i ncrement to the nex t track being play ed.
5 DTS SYSTEM TEST 13. Unblock the timec ode. Once the c i nema proce ssor automatically returns to a dig ital format, go into the theater and listen to the sound track. Verify good sound quality and lip sync. Also verify no extraneous noise during the quiet scenes.
6 DTS 70mm Fail-sa fe Test NOTE: I f using one DTS-6D unit, there is no fail-safe or fall-back available on this ty pe of system. If using two DTS-6D units, verify connections to the fail-safe board. See installation manual. There are no magnetic sound tracks on DTS 70m m prints .
7 DTS TEST DISCS Below is a list of all the test discs released by DTS. Some of these test discs are obsolete and should no longer be used. I n m ost cases, the discs are obsolet e due to software changes that made them incompat ible with curr ent DTS playe rs.
8 DTS EMPIRICAL TEST DI SC Te sts # 1 t hro ugh #35 will play automatically . For a specific test, wait f or the announcem ent, then select the des ired test number on the TI M ECODE HE AD OFF SE T rotary switch es (located behind the play er's front panel acces s cover).
9 DTS SYSTEM TROUBLESHOOTING 1. Movie not playing in DTS digital sound, CP (cinema process o r ) w on’t sw itch to DTS format. Is t h e SYSTEM light blinking on the DTS player? NO System is not ready to play . Ensure movie disc(s) are in the DTS player.
10 SYSTEM TROUBLESHOOTING 1. (continued) . Movie not playing in DT S digital sound, CP (cinem a processor) won’t switch to DTS format . * Is CP in the correct sound format ? I n most cases, DTS will automatica lly pulse the CP. • I f re-starting after film break , some autom ation systems m ay switch the CP out of the dig ital format.
11 SYSTEM TROUBLESHOOTIN G 2. ( continued) DTS digital m ovie defaulting to optical (analog) and not stay ing in digital. • If the reader’s g reen LE D is solid and the DTS still defaults, look at the lights on CD-ROM drives themselv es. They should blink sporadically when their disc is being read.
12 SYSTEM TROUBLESHOOTIN G 6. Sound not in sync with pict ure. * Turn off the DTS player until the audience leav es. Get the DTS num bered leader. Thread it through DTS reader & projector. Put “00” at reader’s lens and find number at sound head.
13 SYSTEM TROUBLESHOOTIN G 12. Noise, distortion, and other sound anom alies. * Apparent in optical as well? Not a DTS player problem . • Turn off all am ps, one by one to localize the problem. If an am p hums or is noisy, replace it. • If us ing Kin tek KT-90 subw oofer amps, thes e are prone to hum because they are s elf-pow ered.
14 SYSTEM TROUBLESHOOTIN G 13. Channel output too low/high and won’t adjust. * Apparent in optical as well? Not a DTS player problem . Are all the amps on? * Apparent in DTS only, turn off the D T S player until there is tim e to troubleshoot. • Use DTS Setup Disc to verify DTS SPL adjustments.
15 SYSTEM TROUBLESHOOTIN G 17. Volume too loud / soft. If the ov erall volume is too loud/soft: Adjust fader pot on CP. Do not adjust DT S player trim pots behind front panel. If sound lev el not balanced between analog and digital, verify B-chain alignm ent.
16 SYSTEM TROUBLESHOOTIN G 20. No Subwoofer. * Verify the subwoofer am p is powered on. * Use the DTS Setup disc to verify DTS subwoofer output. * On a CP65, verify the sub switch on the CAT441 is in AUTO .
17 DTS-6 /-6D UNIT TROUBLESHOOTING W hen making any repairs to the DTS player, be sure to update the TCR firmware (U14 on the D422 board). 1. DRIVE P ROBLEMS • Noisy operation • The drive m otors on in-service older DTS- 6D players are at the end of their useful life.
18 DTS-6/D TROUBLESHOOTI NG 7. WON’T BOOT / LOAD • Verify dri ve assignments and that each drive is spi nning. • Verify that th e ROM-DOS chip is programme d with the latest version firmware. NOTE: On DTS players with FUTURE DOMAIN SCSI board, the ROM-DOS RevE is located at U12 on the DTS D422 board.
19 Replaci ng CD-ROM Driv es We have used only two manufacturers of CD-ROM drives, Toshiba and TEAC. Do not substitute with any other manufacturer. Only drives approve d by DTS w ill work . Toshiba / Future Domain SCSI and the “ ROM-DOS” chip When replacing drives with ones made by Toshiba, be sure to use the current “ ROM-DOS” chip.
20 REPLACI NG C D-ROM DRIVES Address the TEAC drives f or their location. DTS-6D DTS-6 Termination program med TEAC 16X Drive A : Jumper 2, 4, 6 Jum per 2, 4, 6 on Pin 4, t hat shoul d be Drive B : Jum per 0, 2, 4, 6 Jum per 0, 2, 6 removed to activate.
21 DRI VE “A ” DRI VE “A ” DRI VE “ B” DRI VE “ B” DRI VE “ C” DRI VE “ C” *See not e *See not e *If you have a 2 drive unit: Pla ce ju mper over “ TERM”o n dr i ve B , o the rw is e u s e d ri v e C. *If you have a 2 drive unit: jum per over “TERM ” on drive B, ot herwise the jumper on drive C.
22.
23.
24.
25.
26 BLINKING TIMECODE READER LED The timecode reader LED should remain brig ht and not flash more than a few times a minute. Ex cessive flashing indicates a problem and should be fixed as soon as possible. The optics on the reader should be blown off with compressed air at least once a day , but never ad just the len s .
27 BLI NKING TI MECODE READER LED Film Instability, continued • Gently squee ze the edges of the film betwe en two finge rs as it enters the rea der, pull back slig htly a nd allow y our fing ers to ac t as shock absorbers. Repeat on the exit side of the rea der.
28.
29 DTS-6 (2-drives) 35m m / 70mm System Parts List D431-00 Logic break -out board (gen eric, Dolby CP50, CP100, Ody ssey s ystem ) D490-00 Logi c break-out board (Dol by C P 55) D496-00 Logi c break-o.
30 DTS-6D (3-drives) 35m m / 70m m System P arts List D564 Logi c break-ou t board (Dolby C P65) D565 Logic break -out board (Dolby CP55, “generic”) D567 Interface board (Dolby CP200, CP100, CP50).
31 Replacem ent Parts List Replacement Parts com mon to both the DTS-6 and DTS -6D 6303-0001-00 CD-ROM drive cleaning disc 2201-SW0D-02 Power supply module 5108-0019-00 Adaptec SCSI Board 5108-0020-00.
32 HOW TO CONTACT DTS Technical Assistance On-Line Send email to c inematech@dtsonline.com Telephone Business hours are from 8:30am until 5:30pm PDT. After hours, an automated answering service will take your call and a DTS engineer will be paged to help y ou.
Een belangrijk punt na aankoop van elk apparaat DTS DTS-6D (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen DTS DTS-6D heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens DTS DTS-6D vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding DTS DTS-6D leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over DTS DTS-6D krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van DTS DTS-6D bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de DTS DTS-6D kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met DTS DTS-6D . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.