Gebruiksaanwijzing /service van het product 8940 van de fabrikant Dukane
Ga naar pagina of 64
P or table LCD Pr ojector Models 8940 USER'S MANU AL 401-8940-00.
.
1 Projector 8940 8940 User's Manual - Operating Guide User's Manual - Operating Guide Thank you for purchasing this projector. TRADEMARK ACKNOWLEDGMENT : • VGA and XGA are registered trademarks of the International Business Machines Corporation.
2 Projector Features Projector Features ● Ultra High Brightness Crisp, ultra-bright presentations is achieved by using a UHB (ultra high brightness) lamp and a highly efficient optical system. ● Whisper Mode Equipped Special mode is available for reducing projector noise to achieve quieter operation.
3 Contents Contents Projector Features ···························2 Preparation ·······································2 Part Names ·.
4 Part Names Part Names Projector 1 Elevator button 2 Elevator foot 3 Remote sensor 4 Lens cap 5 Lens The picture is projected from here. 6 Filter cover An air filter is inside.
VIDEO RGB SEARCH FREEZE OFF ON MAGNIFY ASPECT AUTO BLANK MUTE VOLUME KEYSTONE POSITION ESC ENTER MENU RESET ZOOM + - FOCUS + - PinP 1 4 6 7 13 14 16 17 18 29 20 19 21 24 23 28 22 26 27 25 5 Part Names.
6 Setting Up Setting Up Arrangement WARNING • Before installation, make sure that the projector is turned off and the power code is disconnected. • Do not set up and move the projector, while it is hot. • Install the projector in a suitable environment according to instructions of the “User’s Manual – Safety Guide” and this manual.
7 Setting Up (continued) Setting Up (continued) Adjusting The Projector's Elevator You can use the elevator feet to make adjustments if the surface on which you need to set the projector is uneven or if you otherwise need to adjust the angle of projection.
8 Setting Up (continued) Setting Up (continued) Connecting Y our Devices WARNING • Whenever attempting to connect other devices to the projector, read thoroughly the "User's Manual - Safety Guide", this manual and the manual of each device to be connected.
9 Setting Up (continued) Setting Up (continued) Please refer to the following (for example) for connecting your devices. See the rear of the projector.
10 Setting Up (continued) Setting Up (continued) AUD IO IN 1 AUD IO IN2 RGB RGB OUT REMOTE CONTROL AUD IO OUT C R /P R C B /P B CONTROL R - AUDIO IN - L VIDEO IN S-VIDEO IN Y R/C R /P R G/Y B/C B /P B.
11 Setting Up (continued) Setting Up (continued) AUD IO IN 1 AUD IO IN2 RGB RGB OUT REMOTE CONTROL AUD IO OUT C R /P R C B /P B CONTROL R - AUDIO IN - L VIDEO IN S-VIDEO IN Y R/C R /P R G/Y B/C B /P B.
12 Remote Control Remote Control Putting Batteries CAUTION • About the battery • Keep a battery away from children and pets. • Use only the battery specified: two AA batteries.
13 Remote Control (continued) Remote Control (continued) Operating The Remote Control CAUTION • Do not disassemble the remote control. • Do not place the remote control near the projector’s lens, fan, or vents. • Do not drop or otherwise expose the remote control to physical impact.
14 VIDEO RGB SEARCH MAGNIFY ASPECT AUTO BLANK VOLUME PinP Tu r ning On The Power WARNING • When the power is ON, a strong light is emitted. Do not look into the lens or vents of the projector. • Turn the power on/off in right order. Please power on the projector before the connected devices.
15 VIDEO RGB SEARCH FREEZE OFF ON MAGNIFY ASPECT AUTO BLANK MUTE VOLUME KEYSTONE POSITION ESC ENTER MENU RESET ZOOM + - FOCUS + - PinP Operating Operating Selecting An Input Signal Select an input signal. Turn the INPUT dial of the projector. Turning the dial cycles through the input ports as shown below.
16 VIDEO RGB SEARCH FREEZE OFF ON MAGNIFY ASPECT AUTO BLANK MUTE VOLUME KEYSTONE POSITION ESC ENTER MENU RESET ZOOM + - FOCUS + - PinP VIDEO RGB SEARCH FREEZE OFF ON MAGNIFY ASPECT AUTO BLANK MUTE VOL.
VIDEO RGB SEARCH FREEZE OFF ON MAGNIFY ASPECT AUTO BLANK MUTE VOLUME KEYSTONE POSITION ESC ENTER MENU RESET ZOOM + - FOCUS + - PinP 17 VIDEO RGB SEARCH FREEZE OFF ON MAGNIFY ASPECT AUTO BLANK MUTE VOL.
18 VIDEO RGB SEARCH FREEZE OFF ON MAGNIFY ASPECT AUTO BLANK MUTE VOLUME KEYSTONE POSITION ESC ENTER MENU RESET ZOOM + - FOCUS + - PinP VIDEO RGB SEARCH FREEZE OFF ON MAGNIFY ASPECT AUTO BLANK MUTE VOL.
19 VIDEO RGB SEARCH FREEZE OFF ON MAGNIFY ASPECT AUTO BLANK MUTE VOLUME KEYSTONE POSITION ESC ENTER MENU RESET ZOOM + - FOCUS + - PinP Operating (continued) Operating (continued) Freezing The Scr een Press the FREEZE button. As illustrated on the right, a dialog will appear on the screen, and the screen will freeze at the current image.
VIDEO RGB SEARCH FREEZE OFF ON MAGNIFY ASPECT AUTO BLANK MUTE VOLUME KEYSTONE POSITION ESC ENTER MENU RESET ZOOM + - FOCUS + - PinP 20 VIDEO RGB SEARCH FREEZE OFF ON MAGNIFY ASPECT AUTO BLANK MUTE VOL.
21 Multifunctional Settings Multifunctional Settings Using The Menu Functions This projector has the following menus: MAIN, PICTURE-1, PICTURE-2, INPUT, AUTO, SCREEN, OPTION and NETWORK. Each of these menus is operated using the same methods. The basic operations of these menus are as follows.
22 Multifunctional Settings (continued) Multifunctional Settings (continued) MAIN Menu With the MAIN menu, the items shown in the table below can be performed.
23 PICTURE-1 Menu With the PICTURE-1 menu, the items shown in the table below can be performed. Perform each operation in accordance with the instructions in the table below.
24 Multifunctional Settings (continued) Multifunctional Settings (continued) Item Description MY MEMORY Select a command to load or save using the / buttons, and then press the (or the ENTER) button to perform the function.: This projector has 4 numbered memories for adjustment data.
25 Multifunctional Settings (continued) Multifunctional Settings (continued) PICTURE-2 Menu With the PICTURE-2 menu, the items shown in the table below can be performed.
26 Multifunctional Settings (continued) Multifunctional Settings (continued) INPUT Menu With the INPUT menu, the items shown in the table below can be performed.
27 Multifunctional Settings (continued) Multifunctional Settings (continued) INPUT Menu (continued) Item Description P.IN P. INPUT Select a signal input port for the child window using the / buttons. : VIDEO S-VIDEO memo About the child window, please refer to the section “Displaying the Child Window”.
28 Multifunctional Settings (continued) Multifunctional Settings (continued) AUTO Menu With the AUTO menu, the items shown in the table below can be performed. Perform each operation in accordance with the instructions in the table below. Item Description ADJUST Pressing the (or the ENTER) button performs the automatic adjustment.
29 Multifunctional Settings (continued) Multifunctional Settings (continued) Item Description SEARCH Select the TURN ON or the TURN OFF using the / buttons. : TURN ON TURN OFF When the TURN ON is selected, detecting no signal cycles through input ports and displays the picture of retrieved signal.
30 Multifunctional Settings (continued) Multifunctional Settings (continued) SCREEN Menu With the SCREEN menu, the items shown in the table below can be performed.
31 Multifunctional Settings (continued) Multifunctional Settings (continued) Item Description MESSAGE Select the TURN ON or the TURN OFF using the / buttons. : TURN ON TURN OFF When the TURN ON is selected, the following message function works. The message of the “AUTO IN PROGRESS” for the auto adjustment.
32 Multifunctional Settings (continued) Multifunctional Settings (continued) OPTION Menu With the OPTION menu, the items shown in the table below can be performed.
33 Multifunctional Settings (continued) Multifunctional Settings (continued) Item Description SERVICE Pressing the (or the ENTER) button calls the SERVICE menu. SERVICE Menu Select an item using the / buttons, and press the (or the ENTER) button to per form each function.
34 Lamp Lamp The projector uses a high-pressure mercury glass lamp. The lamp can break with a loud bang, or burn out, if jolted or scratched, handled while hot, or worn over time. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them.
35 Lamp (continued) Lamp (continued) After making sure that the projector has cooled adequately, slide the knob of a lamp cover lock as shown in the Figure. Then, one side of the lamp cover is raised. Pull up the lamp cover and remove it, as shown in the Figure.
Apply a vacuum cleaner to the top of the filter cover and the air filter to clean. If the soiling will not come off the air filter, or it becomes damaged, it needs to be replaced. If the air filter needs to be replaced, contact your dealer to prepare a new air filter.
37 Other Care Other Care WARNING • Please carefully read the “User’s Manual - Safety Guide”. • Before caring, make sure the power switch is off and the power cable is not plugged in. • Be cautious of high temperature. Do not touch about the lens and ventilation openings during use or immediately after use prevent a burn.
38 T T roubleshooting roubleshooting Related Messages When the unit's power is on, messages such as those shown below may be displayed. When any such message is displayed on the screen, please respond as described below.
39 Related Messages (continued) T T roubleshooting (continued) roubleshooting (continued) Message Description CLEAN THE AIR FILTER POWER OFF FIRST, THEN CLEAN THE AIR FILTER. AFTER CLEANING THE AIR FILTER, RESET THE FILTER TIMER. The time the filter timer has counted has reached 100 hours.
40 T T roubleshooting (continued) roubleshooting (continued) Regarding The Indicator Lamps Lighting and flashing of the STANDBY/ON indicator, the LAMP indicator, and the TEMP indicator have the meanings as described in the table below. Please respond in accordance with the instructions within the table.
41 T T roubleshooting (continued) roubleshooting (continued) Regarding The Indicator Lamps (continued) STANDBY/ON indicator LAMP indicator TEMP indicator Description Lighting in Red Blinking in Red Turned off Either there is no lamp and/or lamp cover, or either of these has not been properly fixed.
42 T T roubleshooting (continued) roubleshooting (continued) Phenomena That May Easily Be Mistaken For Machine Defects WARNING • Never use the projector if abnormal operations such as smoke, strange odor, excessive sound, damaged casing or elements or cables, penetration of liquids or foreign matter, etc.
43 T T roubleshooting (continued) roubleshooting (continued) Phenomena That May Easily Be Mistaken For Machine Defects (continued) Phenomenon Cases not involving a machine defect Reference pages Pictures are displayed, but no sounds are heard. The signal cables are not correctly connected.
44 If a problem occurs with the equipment, first refer to the “Troubleshooting” and run through the suggested checks. If this does not resolve the problem, please contact your dealer or service company. They will tell you what warranty condition is applied.
45 Projector 8940 8940 User's Manual - Operating Guide User's Manual - Operating Guide TECHNICAL Dimensions Dimensions [unit: mm].
46 • Be sure to check jack type, signal level, timing and resolution before connecting this projector to a computer. • Some computers may hove multiple display screen modes. Use of some of these modes will not be possible with this projector. • Depending on the input signal, full-size display may not be possible in some cases.
47 Initial Set Signals Initial Set Signals The following signals are used for the initial settings. The signal timing of some computer models may be different. In such case, adjust the items V POSITION and H POSITION in the PICTURE-2 menu. DATA H. Sync.
48 • Video signal: RGB separate, Analog, 0.7 Vp-p, 75 Ω terminator (positive) • H./V. sync. Signal: TTL level (positive/negative) • Composite sync.
49 Connection T Connection T o The Ports (continued) o The Ports (continued) Mini Din 4 pin jack 12 3 4 I VIDEO IN • RCA jack • System: NTSC, PAL, SECAM, PAL-M, PAL-N, NTSC4.
50 Connection T Connection T o The Ports (continued) o The Ports (continued) AUD IO IN 1 AUD IO IN2 RGB RGB OUT REMOTE CONTROL AUD IO OUT C R /P R C B /P B CONTROL R - AUDIO IN - L VIDEO IN S-VIDEO IN.
51 RS-232C Communication RS-232C Communication Connecting The Cable Turn off the projector and the computer power supplies. Connect the CONTROL port of the projector with a RS-232C port of the computer by a RS-232C cable. Use the cable that fulfills the specification shown in the previous page.
52 RS-232C Communication (continued) RS-232C Communication (continued) Requesting projector status (Get command) (1) Send the request code Header + Command data (‘02H’+‘00H’+ type (2 bytes)+‘00H’+‘00H’) from the computer to the projector.
53 RS-232C Communication (continued) RS-232C Communication (continued) Command Data Chart Names Operation type Header Command data CRC Action Type Setting code Keystone V Get BE EF 03 06 00 B9 D3 02 0.
54 RS-232C Communication (continued) RS-232C Communication (continued) Command Data Chart (continued) (This table is Names Operation type Header Command data CRC Action Type Setting code Language Set .
55 RS-232C Communication (continued) RS-232C Communication (continued) Command Data Chart (continued) Names Operation type Header Command data CRC Action Type Setting code Custom User B Set 50 BE EF 0.
56 Command Data Chart (continued) Names Operation type Header Command data CRC Action Type Setting code V Position Get BE EF 03 06 00 0D 83 02 00 00 21 00 00 Increment BE EF 03 06 00 6B 83 04 00 00 21.
57 RS-232C Communication (continued) RS-232C Communication (continued) Command Data Chart (continued) Names Operation type Header Command data CRC Action Type Setting code Video NR Set LOW BE EF 03 06.
58 RS-232C Communication (continued) RS-232C Communication (continued) Command Data Chart (continued) (This table is continued to the following page.) Names Operation type Header Command data CRC Acti.
59 RS-232C Communication (continued) RS-232C Communication (continued) Command Data Chart (continued) Names Operation type Header Command data CRC Action Type Setting code PinP Size Set Off BE EF 03 0.
60 RS-232C Communication (continued) RS-232C Communication (continued) Names Operation type Header Command data CRC Action Type Setting code Power Up Source Set Last Ch BE EF 03 06 00 9E D9 01 00 18 2.
.
2900 Dukane Drive St. Charles, Illinois 60174 www .dukcor p .com/av T oll-free: 800-676-2487 F ax: 630-584-5156 e-mail: avsales@dukcorp.com A udio Visual Products #401-8940-00.
Een belangrijk punt na aankoop van elk apparaat Dukane 8940 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Dukane 8940 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Dukane 8940 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Dukane 8940 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Dukane 8940 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Dukane 8940 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Dukane 8940 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Dukane 8940 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
