Gebruiksaanwijzing /service van het product 8943 van de fabrikant Dukane
Ga naar pagina of 137
P ortable LCD Projector Model 8943 8918 USER’S MANUAL #070030.
1 Projector 8918/8943 User's Manual – Oper ating Guide Thank you for purchasing this projector . WARNING Before using this product, please read the “Safety Guide” section and related sections to ensure the proper use of this product. After reading section, store this in a safe place for future reference.
2 About this manual . . . . . . . . . . 1 Content . . . . . . . . . . . . . . . . . . 2 Projector features . . . . . . . . . . 3 Prepar ations . . . . . . . . . . . . . . 3 Contents of package . . . . . . . . . . . . .3 Fastening the lens cover . . . .
3 F astening the lens co ver T o avoid losing the lens cover , please fasten the lens cover to the projector using the included strap. 1. Fix the strap to the strap hole of the lens cover . 2. Put one side of the strap into the groove on the rivet. 3.
4 Par t names Part names Projector (1) Speakers (x 4) ( 37 ). (2) Focus ring ( 19 ) (3) Zoom ring ( 19 ) (4) Lamp cover ( 56 ) The lamp unit is inside.
5 Par t names Control panel (1) ST ANDBY/ON button ( 16 ) (2) MENU button ( 23 ) It consists of four cursor buttons. (3) INPUT button ( 17 ) (4) POWER indicator ( 16 ) (5) TEMP indicat.
6 Par t names R emote control (1) Laser pointer ( 13 ) It is a beam outlet. (2) LASER INDICA TOR ( 13 ) (3) LASER button ( 13 ) (4) ST ANDBY/ON button ( 16 ) (5) VOLUME button ( 17.
7 Setting up Setting up Install the projector according to the environment and manner the projector will be used in. WARNING ► Place the projector in a stable horizontal position. If the projector falls or is knocked over it could cause injury and/or damage to the projector .
8 Ar r angement Refer to the illustrations and tables below to determine screen size and projection distance. The values shown in the table are calculated for a full size screen: 1024×768 (a) Screen .
9 Adjusting the projector's eleva tor When the place to put the projector is slightly uneven to the left or right, use the elevator feet to place the projector horizontally . Using the feet can also tilt the projector in order to project at a suitable angle to the screen, elevating the front side of the projector within 8 degrees.
10 Setting up Connecting your de vices Be sure to read the manuals for devices before connecting them to the projector . Make sure that all the devices are suitable to be connected with this product, and prepare the cables required to connect. Please refer to the following illustrations to connect them.
1 1 Setting up NOTE • Be sure to read the manuals for devices before connecting them to the projector , and make sure that all the devices are suitable to be connected with this product. Before connecting to a PC, check the signal level, the signal timing, and the resolution.
12 Setting up Connecting pow er suppl y 1. Connect the connector of the power cord to the AC inlet of the projector . 2. Firmly plug the power cord's plug into the outlet. WARNING ► Please use extra caution when connecting the power cord, as incorrect or faulty connections may result in re and/or electrical shock.
13 Remote control Putting batteries Please load the batteries before using the remote control. If the remote control starts to malfunction, replace the batteries. If you will not use the remote control for an extended period, remove the batteries from the remote control and store them in a safe place.
14 Changing the frequency of remote contr ol signal The accessory remote control has the choice of the mode 1 or the mode 2, in the frequency of its signal. If the remote control does not function properly , attempt to change the signal frequency . Please remember that the “REMOTE FREQ.
15 Using as a wired r emote contr ol The accessory remote control works as a wired remote control, when the wired control port at the bottom of the remote control connects with the REMOTE CONTROL por t o n the ba ck of th e p roj ect or vi a a n a udi o cabl e with 3.
16 Po wer on/of f T ur ning on the po wer 1. Make sure that the power cord is rmly and correctly connected to the projector and the outlet. 2. Remove the lens cover , and set the power switch to the ON position. The power indicator will light up in steady orange ( 63 ).
17 Operating Operating Adjusting the v olume 1. Press the VOLUME button on the remote control. A dialog will appear on the screen to aid you in adjusting the volume. 2. Use the cursor buttons ▲/▼ to adjust the volume. T o close the dialog and complete the operation, press the VOLUME button again.
18 Operating Searching an input signal 1. Press the SEARCH button on the remote control. The projector will start to check its input ports in order to nd any input signals. When an input is found, the projector will stop searching and display the image.
19 Adjusting the zoom and f ocus 1. Use the zoom ring to adjust the screen size. 2. Use the focus ring to focus the picture. Operating Focus ring Zoom ring Adjusting the lens shift 1. Use the vertical lens shift dial to shift the picture upward or downward.
20 Adjusting the position 1. Press the POSITION button on the remote control. The “POSITION” indication will appear on the screen. 2. Use the cursor buttons ▲/▼/◄/► to adjust the picture position. When you want to reset the operation, press the RESET button on the remote control during the operation.
21 Operating Using the magnify feature 1. Press the ON button of MAGNIFY on the remote control. The “MAGNIFY” indication will appear on the screen (although the indication will disappear in several seconds with no operation), and the projector will go into the MAGNIFY mode.
22 Operating T empor aril y blanking the screen 1. Press the BLANK button on the remote control. The blank screen will be displayed instead of the screen of input signal. Please refer to the BLANK item in SCREEN menu ( 38 ). T o exit from the blank screen and return to the input signal screen, press the BLANK button again.
23 Operating Using the menu function This projector has the following menus: PICTURE, IMAGE, INPUT , SETUP , AUDIO, SCREEN, OPTION, NETWORK, and EASY MENU. EASY MENU consists of functions often used, and the other menus are classied into each purpose.
24 EASY Menu EASY Menu Item Description ASPECT Using the ◄/► buttons switches the mode for aspect ratio. See the ASPECT item in IMAGE menu ( 29 ). AUTO KEYSTONE EXECUTE Using the ► button executes the auto keystone function. See the AUTO KEYST ONE EXECUTE item in SETUP menu ( 35 ).
25 EASY Menu Item Description BRIGHTNESS Using the ◄/► buttons adjusts the brightness. See the BRIGHTNESS item in PICTURE menu ( 26 ). CONTRAST Using the ◄/► buttons adjusts the contrast. See the CONTRAST item in PICTURE menu ( 26 ). COLOR Using the ◄/► buttons adjusts the strength of whole color .
26 PICTURE Menu PICTURE Menu Item Description BRIGHTNESS Using the ▲/▼ buttons adjusts the brightness. Light ó Dark CONTRAST Using the ▲/▼ buttons adjusts the contrast.
27 Item Description COLOR TEMP Using the ▲/▼ buttons switches the color temperature mode. T o adjust CUSTOM Selecting a mode whose name includes CUSTOM and then pressing the ► button or the ENTER button displays a dialog to aid you in adjusting the OFFSET and GAIN of the selected mode.
28 PICTURE Menu Item Description ACTIVE IRIS Using the ▲/▼ cursor buttons changes the active iris control mode. PRESENT A TION ó THEA TER ó TURN OFF Feature PRESENT A TION The active iris displays the best presentation image for both bright and dark scenes.
29 IMAGE Menu IMAGE Menu Item Description ASPECT Using the ▲/▼ buttons switches the mode for aspect ratio. For an RGB signal NORMAL ó 4:3 ó 16:9 ó SMALL For an M1-D signal NORMAL ó 4:3 ó 16:9.
30 IMAGE Menu Item Description H PHASE Using the ▲/▼ buttons adjusts the horizontal phase to eliminate icker . Right ó Left • This item can be selected only for an RGB signal or a component video signal. (except 525i (480i), 625i (576i), SCART RGB) H SIZE Using the ▲/▼ buttons adjusts the horizontal size.
31 INPUT Menu INPUT Menu Item Description PROGRESSIVE Using the ▲/▼ buttons switches the progress mode. TV ó FILM ó TURN OFF • This function is performed only for an interlaced signal of a VIDEO input, an S-VIDEO input or COMPONENT VIDEO input of 525i (480i), 625i (576i) or 1 125i (1080i) signal.
32 Item Description COMPONENT Using the ▲/▼ buttons switches the function of the COMPONENT (Y , C b /P b , C r /P r ) port. COMPONENT ó SCAR T RGB When the SCART RGB is selected, the COMPONENT (Y , C b /P b , C r /P r ) and VIDEO ports will function as a SCART RGB port.
33 Item Description FRAME LOCK Using the ▲/▼ buttons turns the frame lock function on/off. TURN ON ó TURN OFF • This item can be performed only on an RGB signal with a vertical frequency of 50 to 60 Hz. • When the TURN ON is selected, a moving pictures are displayed more smoothly .
34 INPUT Menu Item Description RESOLUTION The resolution for the RGB1 and RGB2 input signals can be set on this projector . (1) In the INPUT menu select the RESOLUTION using the ▲/▼ buttons and press the ► button. The RESOLUTION menu will be displayed.
35 SETUP Menu SETUP Menu Item Description AUTO KEYSTONE EXECUTE Selecting this item performs the Automatic keystone distortion correction. Projector automatically corrects vertical keystone distortion due to the (forward/backward) setup angle by itself.
36 SETUP Menu SETUP Menu (continued) Item Description WHISPER Using the ▲/▼ buttons turns off/on the whisper mode. NORMAL ó WHISPER • When the WHISPER is selected, acoustic noise and screen brightness are reduced. MIRROR Using the ▲/▼ buttons switches the mode for mirror status.
37 A UDIO Menu AUDIO Menu Item Description VOLUME Using the ▲/▼ buttons adjusts the volume. High ó Low TREBLE Using the ▲/▼ buttons adjusts the treble level. High ó Low BASS Using the ▲/▼ buttons adjusts the bass level. High ó Low SRS WOW Using the ▲/▼ buttons switches the mode for SRS WOW mode.
38 SCREEN Menu SCREEN Menu Item Description LANGUAGE Using the ▲/▼ buttons switches the OSD (On Screen Display) language. SUOMI ó POLSKI ó TÜRKÇE ENGLISH ó FRANÇAIS ó DEUTSCH ó ESP AÑOL .
39 SCREEN Menu Item Description ST ART UP Using the ▲/▼ buttons switches the mode for the start-up screen. The start-up screen is a screen displayed when no signal or an unsuitable signal is detected. MyScreen ó ORIGINAL ó TURN OFF Feature MyScreen Screen can be registered by the MyScreen item ( 40 ) .
40 SCREEN Menu Item Description MyScreen This item allows you to capture an image for use as a MyScreen image which can be used as the BLANK screen and ST ART UP screen. Display the image you want to capture before executing the following procedure. 1.
41 SCREEN Menu Item Description MESSAGE Using the ▲/▼ buttons turns on/off the message function. TURN ON ó TURN OFF When the TURN ON is selected, the following message function works. “AUTO IN PROGRESS” while automatically adjusting “NO INPUT IS DETECTED” “SYNC IS OUT OF RANGE” “Searching….
42 OPTION Menu OPTION Menu Item Description AUTO SEARCH Using the ▲/ ▼ buttons t urns on/of f the automatic sign al search fu nction. TURN ON TURN OFF When the TURN ON is selected, detecting no signal automatically cycles through input ports in the following order .
43 Item Description AUTO OFF Using the ▲/▼ buttons adjusts the time to count down to automatically turn the projector off. Long (max. 99 minutes) ó Short (min. 0 minute = DISABLE) AUTO OFF ENABLE 1 AUTO OFF DISABLE 0 When th e time i s set t o 0, th e proje ctor is not tur ned of f automatical ly .
44 Item Description MY BUTT ON This item is to assign one of the following function to MY BUTT ON 1 and 2 on the remote control ( 6 ). Choose 1 or 2 on the MY BUTT ON menu using the ◄/► button rst. Then using the ▲/▼ buttons s ets one of the following func tions to the chosen button.
45 Item Description SERVICE AUTO ADJUST Using the ▲/▼ buttons enables/disables the automatic adjustment.When DISABLE is selected, the automatic adjustment feature is disabled, although rough adjustment is automatically performed depending on the basic setting.
46 Item Description SERVICE KEY LOCK Using the ▲/▼ buttons turns on/off the key lock feature. When TURN ON is selected, the buttons on the projector except the ST ANDBY/ON button are locked. TURN ON ó TURN OFF • Please use to avoid a mischief and touching accidentally .
47 Item Description SECURITY This projector is equipped with security functions. User registration is required before using the security functions. Please contact your local dealer . 1. Using Security Features 1.1 Inputting the P ASSWORD 1.1-1 Use the ▲/▼ buttons on the OPTION menu to select SECURITY and press the ► button.
48 Item Description SECURITY 1.3 If you have forgotten your P ASSWORD 1.3-1 Follow the procedure in 1.1-1 to display the ENTER P ASSWORD BOX. 1.3-2 While the ENTER P ASSWORD BOX is displayed, press and hold the RESET button on the remote control for about 3 seconds or press and hold the INPUT and ► buttons on the projector for about 3 seconds.
49 Item Description SECURITY 2.2-4 Move the cursor to the right side of the CHECK P ASSWORD BOX and press the ► button to display the P ASSWORD for about 20 seconds, please make note of the P ASSWORD during this time. Pressing the ENTER button on the remote control or INPUT button on the projector will return to MyScreen P ASS WORD on/off menu.
50 Item Description SECURITY 3.1-3 Input a 4 part PIN Code using the ▲/▼/◄/► /RGB and INPUT buttons. A CONFIRMA TION BOX will appear . Reenter the same PIN Code. This will complete the PIN Code registration. NOTE: If there is no key input for about 55 seconds while the PIN BOX or the CONFIRM A TION BOX are displayed the menu will close.
51 Item Description SECURITY 4. Using the T ransition Detector Function While the T ransition Detector function is ON, when power switch is started to supply to the projector , it might react as below . • T ransition Detector alarm shown below might appear on screen, if the projector has been moved or re-installed.
52 Item Description SECURITY 4.3 Setting the T ransition Detector off 4.3-1 Follow the procedure in 4.1-1 to display the T ransition Detector on/off menu. 4.3-2 Select TURN OFF to display the ENTER P ASSWORD BOX (large). Enter the registered P ASSWORD and the screen will return to the T ransition Detector on/off menu.
53 NETWORK Menu /'07 = 4)$ ? 5'.'%6 +2#&&4'55 57$0'6/#5- 6+/'&+(('4'0%' &*%2 674010 &'(#7.
54 NETWORK Menu Item Description TIME DIFFERENCE Entering the TIME DIFFERENCE : Use the ▲/▼ buttons to enter the TIME DIFFERENCE. Set the same TIME DIFFERENCE as the one set on your PC. If unsure, consult your network administrator . Use the ◄ button to return to the menu after setting the TIME DIFFERENCE.
55 Item Description INFORMA TION INFORMA TION display : Use the ► or ENTER buttons to view network information and conrm settings. • Only the rst 16 characters of the projector name are displayed. • The battery for the built in clock may be dead if the clock loses time even when the DA TE AND TIME have been set correctly .
56 Maintenance Lamp A lamp has nite product life. Using the lamp for long periods of time could cause the pictures darker or the color tone poor . Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them.
57 Maintenance Lamp (continued) WARNING HIGH VOL T AGE HIGH TEMPERA TURE HIGH PRESSURE ► The projector uses a high-pressure mercury glass lamp. The lamp can break with a loud bang, or burn out, if jolted or scratched, handled while hot, or worn over time.
58 Please check and clean the air lter periodically . If the air lter becomes clogged by dust or the like, internal temperatures rise, which could cause a re, a burn or malfunction to the projector . When the indicators or a message prompts you to clean the air lter , comply with it as soon as possible.
59 WARNING ►Before taking care of the air lter , make sure the power switch is off and the power cable is not plugged in, then allow the projector to cool sufciently . T aking care of the air lter in a high temperature state of the projector could cause an electric shock, a burn or malfunction to the projector .
60 Maintenance 1. T urn the projector off, and unplug the power cord. Allow the projector to cool sufciently . 2. After making sure that the projector has cooled adequately , slowly turn over the projector , so that the bottom is facing. 3. Remove the battery cover .
61 Maintenance Inside of the projector In order to ensure the safe use of your projector , please have it cleaned and inspected by your dealer about once every year . Caring for the lens If the lens is awed, soiled or fogged, it could cause deterioration of display quality .
62 T roubleshooting R elated messages When the unit's power is on, messages such as those shown below may be displayed. When any such message is displayed on the screen, please follow the instructions described below .
63 T r oubleshooting R e gar ding the indicator lamps Lighting and ashing of the POWER indicator , the LAMP indicator , and the TEMP indicator have the meanings as described in the table below .
64 T r oubleshooting Regarding the indicator lamps (continued) POWER indicator LAMP indicator TEMP indicator Description Blinking In Red or Lighting In Red T urned off Blinking In Red The cooling fan is not operating. Please turn the power off, and allow the projector to cool down at least 20 minutes.
65 T r oubleshooting Phenomena that may be easy to be mistak en for mac hine defects WARNING ► Never use the projector if abnormal operations such as smoke, strange odor , excessive sound, damaged casing or elements or cables, penetration of liquids or foreign matter , etc.
66 Pheno mena tha t may be easy to b e mi stak en fo r ma chin e def ects (co ntinu ed) Phenomenon Cases not involving a machine defect Reference page Sound does not come out. The signal cables are not correctly connected. Correctly connect the audio cables.
67 Pheno mena tha t may be easy to b e mi stak en fo r ma chin e def ects (co ntinu ed) Phenomenon Cases not involving a machine defect Reference page Pictures appear dark. The brightness and/or contrast are adjusted to an extremely low level. Adjust BRIGHTNESS and/or CONTRAST settings to a higher level using the menu function.
68 Warr anty And After-Ser vice / Specica tion W arranty and after-service If a problem occurs with the equipment, rst refer to the “T roubleshooting” and run through the suggested checks. If this does not resolve the problem, please contact your dealer or service company .
69 Specications Specications (continued) 418 319 154 139 [unit: mm].
1 Projector 8918/8943 User's Manual – Oper ating Guide T echnical Example of computer signal Resolution (H x V) H. frequency (kHz) V . frequency (Hz) Rating Signal mode 720 x 400 37.9 85.0 VESA TEXT 640 x 480 31.5 59.9 VESA VGA (60Hz) 640 x 480 37.
2 Initial set signals Initial set signals The following signals are used for the initial settings. The signal timing of some computer models may be different.
3 Connection to the ports A RGB IN1, B RGB IN2, C RGB OUT D-sub 15pin mini shrink jack • Video signal: RGB separate, Analog, 0.7Vp-p, 75Ω terminated (positive) • H/V .
4 Connection to the por ts (continued) 4 3 2 1 I VIDEO RCA jack • System: NTSC, P AL, SECAM, P AL-M, P AL-N, NTSC4.43 • 1.0±0.1Vp-p, 75Ω terminator H S-VIDEO Mini DIN 4pin jack Pin Signal 1 Color signal 0.286Vp-p (NTSC, burst), 75Ω terminator Color signal 0.
5 VIDEO CONTROL AUDIO IN 1 AUDIO IN 2 REMOTE CONTROL (3.5Φ) AUX I/O DC 5V 0.5A S-VIDEO LAN AUDIO OUT AC IN I O R L R L AUDIO IN 3 AUDIO IN 4 RGB OUT RGB1 RGB2 M1-D Y C B /P B C R /P R SD CARD S D C A R D VIDEO CONTROL AUDIO IN 1 AUDIO IN 2 REMOTE CONTROL (3.
6 VIDEO CONTROL AUDIO IN 1 AUDIO IN 2 REMOTE CONTROL (3.5Φ) AUX I/O DC 5V 0.5A S-VIDEO LAN AUDIO OUT AC IN I O R L R L AUDIO IN 3 AUDIO IN 4 RGB OUT RGB1 RGB2 M1-D Y C B /P B C R /P R SD CARD S D C A R D VIDEO CONTROL AUDIO IN 1 AUDIO IN 2 REMOTE CONTROL (3.
7 RS-232C Communication RS-232C Communication 6 7 8 9 1 2 3 4 5 6 7 8 9 1 2 3 4 5 CONTROL port RS-232C cable (Cross) RS-232C port of the projector of the computer - (1) (1) CD RD (2) (2) RD TD (3) (3) TD - (4) (4) DTR GND (5) (5) GND - (6) (6) DSR RTS (7) (7) RTS CTS (8) (8) DTS - (9) (9) RI Connecting the cable 1.
8 RS-232C Communication (continued) Requesting projector status (Get command) (1) Send the request code Header + Command data (‘02 H’+‘00H’+ type (2 bytes)+ ‘00H’ +‘00H’) from the computer to the projector . (2) The projector returns the response code ‘1DH’+ data (2 bytes) to the compu ter .
9 Names Operation T ype Header Command Data CRC Action T ype Setting Code Power Set Turn of f BE EF 03 06 00 2A D3 01 00 00 60 00 00 Turn on BE EF 03 06 00 BA D2 01 00 00 60 01 00 Get BE EF 03 06 00 1.
10 Names Operation T ype Header Command Data CRC Action T ype Setting Code User Gamma Pattern Set Off BE EF 03 06 00 FB F A 01 00 80 30 00 00 9 step gray scale BE EF 03 06 00 6B FB 01 00 80 30 01 00 1.
1 1 Names Operation T ype Header Command Data CRC Action T ype Setting Code COLOR TEMP GAIN B Get BE EF 03 06 00 8C F5 02 00 B3 30 00 00 Increment BE EF 03 06 00 EA F5 04 00 B3 30 00 00 Decrement BE E.
12 Names Operation T ype Header Command Data CRC Action T ype Setting Code ASPECT Set 4:3 BE EF 03 06 00 9E D0 01 00 08 20 00 00 16:9 BE EF 03 06 00 0E D1 01 00 08 20 01 00 14:9 BE EF 03 06 00 CE D6 0.
13 Names Operation T ype Header Command Data CRC Action T ype Setting Code M1-D Set NORMAL BE EF 03 06 00 3E D9 01 00 20 20 00 00 ENHANCED BE EF 03 06 00 AE D8 01 00 20 20 01 00 Get BE EF 03 06 00 0D .
14 Names Operation T ype Header Command Data CRC Action T ype Setting Code VOLUME-Component Get BE EF 03 06 00 01 CC 02 00 65 20 00 00 Increment BE EF 03 06 00 67 CC 04 00 65 20 00 00 Decrement BE EF .
15 RS-232C Communication (continued) Names Operation T ype Header Command Data CRC Action T ype Setting Code SRS WOW RGB2 Set TURN OFF BE EF 03 06 00 CE FE 01 00 94 20 00 00 MID BE EF 03 06 00 AE FF 0.
16 RS-232C Communication (continued) Names Operation T ype Header Command Data CRC Action T ype Setting Code AUDIO - M1-D Set TURN OFF BE EF 03 06 00 BA DD 01 00 33 20 00 00 Audio1 BE EF 03 06 00 2A D.
17 Names Operation T ype Header Command Data CRC Action T ype Setting Code LANGUAGE Set ENGLISH BE EF 03 06 00 F7 D3 01 00 05 30 00 00 FRANÇAIS BE EF 03 06 00 67 D2 01 00 05 30 01 00 DEUTSCH BE EF 03.
18 Names Operation T ype Header Command Data CRC Action T ype Setting Code AUTO SEARCH Set TURN OFF BE EF 03 06 00 B6 D6 01 00 16 20 00 00 TURN ON BE EF 03 06 00 26 D7 01 00 16 20 01 00 Get BE EF 03 0.
19 Names Operation T ype Header Command Data CRC Action T ype Setting Code MY BUTTON-2 Set RGB1 BE EF 03 06 00 C6 32 01 00 01 36 00 00 RGB2 BE EF 03 06 00 06 30 01 00 01 36 04 00 M1-D BE EF 03 06 00 3.
1 Projector 8918/8943 User’ s Manual – Networ k Functions This manual is only intended to explain Network Functions. For safety , operations or any other issues, refer to the all user's manual for this projector .
2 Network Functions Network Functions Conguring and Controlling the Pr ojector via a W eb Browser Y ou can change the settings of or control the projector via a network by using a web browser from a PC that is connected to the same network.
3 Network Functions Before using the network functions… T o use the network functions of this projector , the projector must be congured to suit your network. Consult with your network administrator before connecting the projector to your network.
4 Network Functions Conguring and controlling the projector via a w eb brow ser Y ou can adjust or control the projector via a network from a web browser on a PC that is connected to the same network. • Internet Explorer 5.5 or higher or Netscape 6.
5 Network Functions When conguring or controlling the projector via a web browser , an ID and password are required. There are two types of IDs, Administrator IDs and User IDs. The following chart describes the dif ferences between user and administrator IDs.
6 Settings Settings Refer to the foll owing for conguring or controlling th e projector via a web browser . Example: If the IP address of the projector is set to 192.168.1.10: 1) Enter [https://192.168.1.10] into the address bar of the web browser and the screen in Fig.
7 Settings Network Infor ma tion All screen images displayed in this manual are screens of a logon using an administrator ID. Any administrator only functions will not be displayed when using a user ID. Refer to the descriptions in each table. Displays the projector ’s current network conguration settings.
8 Settings Network Settings Displays and congures network settings. Click the [Apply] button to save the settings. • The new conguration settings are activated after restarting the network connection. When the conguration settings are changed, you must restart the network connection.
9 Settings P or t Settings Displays and congures communication port settings. Click the [Apply] button to save the settings. • The new conguration settings are activated after restarting the network connection. The network connection must be restarted when the conguration settings are changed.
10 Settings Mail Settings Displays and congures e-mail addressing settings. Click the [Apply] button to save the settings. • Y ou can conrm whether the mail settings work correctly using the [Send T est Mail] button. • If you connect the projector to an existing network, consult a network administrator before setting server addresses.
1 1 Settings Aler t Settings Displays and congures failure & warning alerts. Item Description Cover Error Congures Cover Error alert settings. SNMP T rap Click the [Enable] check box to enable SNMP T rap alerts for this item. Send Mail Click the [Enable] check box to enable e-mail alerts for this item.
12 Settings Alert Settings (Continued) Item Description Lamp Error Congures Lamp Error alert settings. SNMP T rap Click the [Enable] check box to enable SNMP T rap alerts for this item. Send Mail Click the [Enable] check box to enable e-mail alerts for this item.
13 Settings Alert Settings (Continued) Item Description Lamp Time Error Congures Lamp T ime Error alert settings. SNMP T rap Click the [Enable] check box to enable SNMP T rap alerts for this item. Send Mail Click the [Enable] check box to enable e-mail alerts for this item.
14 Settings Alert Settings (Continued) Item Description Other Error Congures Other Error alert settings. SNMP T rap Click the [Enable] check box to enable SNMP T rap alerts for this item. Send Mail Click the [Enable] check box to enable e-mail alerts for this item.
15 Settings Alert Settings (Continued) Item Description Filter Time Alarm Congures Filter T ime Alarm alert settings. Alarm Time Congures the lter time to alert. SNMP T rap Click the [Enable] check box to enable SNMP T rap alerts for this item.
16 Settings Schedule Settings Displays and congures schedule settings. Item Description Daily Congures the daily schedule. Schedule Click the [Enable] check box to enable daily scheduling. Schedule List Displays the current daily schedule. Sunday Congures the Sunday schedule.
17 Settings Schedule Setting (Continued) Item Description Specic date No1 Congures the specic date (No.1) schedule. Schedule Click the [Enable] check box to enable specic date (No.1) scheduling. Month/Day Congures the Month and date. Schedule List Displays the current specic date (No.
18 Settings T o add additional functions and events click the [Add] button and set the following items. Item Description Time Congures the time to execute commands. Command Congures the commands to be executed. Power Parameter Congures the parameters for power control.
19 Settings Date/Time Settings (Continued) Click the [Apply] button to save the settings. Item Description Daylight Savings Time Click the [ON] check box to enable daylight savings time and set the following items. SNTP Server I P Address Congures the SNTP server address in IP format.
20 Settings Security Settings Item Description Administrator authority Congures the Administrator ID and Password. Administrator ID Congures the Administrator ID. The length of the text can be up to 32 alphanumeric characters. Administrator Password Congures the Administrator Password.
21 Click the [Apply] button to save the settings. Authentication Password Congures the Authentication Password. The length of the text can be up to 16 alphanumeric characters. Re-ent er Authent icati on Password Used to re-enter the above password for verication.
22 Projector Contr ol Projector Control Projector Contr ol The items shown in the table below can be performed using the [Projector Control] menu. Select an item using the up and down arrow keys on the PC. Most of the items have a submenu. Refer to the table below for details.
23 Projector Contr ol Projector Control (Continued) Item Description Image Aspect Selects the Aspect setting. Over Scan Selects the Over Scan setting. V Position Adjusts the V Position. H Position Adjusts the H Position. H Phase Adjusts the H Phase. H Size Adjusts the H Size.
24 Option V olume Adjusts the V olume setting. T reble Adjusts the T reble setting. Bass Adjusts the Bass setting. SRS WOW Selects the SRS WOW setting. Speaker T urns Speaker On/Off. Audio-RGB1 Assigns the Audio-RGB1 input terminal. Audio-RGB2 Assigns the Audio-RGB2 input terminal.
25 Projector Contr ol Network Restar t Restarts the projector ’s network connection. Item Description Restart Restarts the projector ’s network connection in order to activate new conguration settings. • Restarting requires you to re-log on in order to further control or congure the projector via a web browser .
26 Failure & Warning Aler ts via E-mail Failure & W arning Alerts via E-mail The projector can automatically send an alert to specied e-mail addresses when the projector requires maintenance or has encountered an error . • Up to ve e-mail addresses can be specied.
27 Failure & Warning Aler ts via E-mail 8) Congure the Failure/W arning Alerts via E-mail settings. Click [Alert Settings] on the main menu. 9) Select and congure each alert item. Refer to [Alert Settings] in [Conguring and Controlling the Projector via a Web Browser] for further information.
28 Projector mana gement via SNMP Projector management via SNMP When SNMP is enabled, the projector is able to send Failure/W arning Alerts to a specied PC. • It is recommended that SNMP functions be carried out by a network administrator . • SNMP management software must be installed on the computer to monitor the projector via SNMP .
29 Controlling the Pr ojector via Scheduling Controlling the Projector via Scheduling The projector can be automatically controlled via scheduling. • Y ou can schedule the following control events: Power ON/OFF , Input Source and T ransferred Image Display .
30 Controlling the Pr ojector via Scheduling Date/Time Settings The Date/T ime setting can be adjusted via a web browser . Example: If the IP address of the projector is set to 192.168.1.10: • A Network Restart is required after the Daylight Savings T ime or SNTP conguration settings have been changed.
31 Controlling the Pr ojector via Scheduling Schedule Settings Schedule settings can be congured from a web browser . Example: If the IP address of the projector is set to 192.168.1.10: ( 16 ) There are three types of scheduling. 1) Daily: Perform the specied operation at a specied time every day .
32 e-SHOT (Still Image T r ansfer) Display e-SHOT (Still Ima ge T ransfer) Display The projector can display a still image that is transferred via the network.
33 e-SHOT(Still Image T r ansfer) Display e-SHOT (Still Image Transfer) Settings (Continued) When the authentication setting is enabled, the following settings are required. 6) Click [Security Settings] on the main menu. 7) Select [Network Control] and enter the desired authentication password.
34 Command Control via the Networ k Command Control via the Network Y ou can congure and control the projector via the network using RS-232C commands.
35 Command Control via the Networ k Command Control Settings (Continued) When the authentication setting is enabled, the following settings are required. ( 20 ) 7) Click [Security Settings] on the main menu. 8) Click [Network Control] and enter the desired authentication password.
36 Command Control via the Networ k Command for mat Command formats differ among the dif ferent communication ports. TCP #23 Y ou can use the RS-232C commands without any changes.
37 Command Control via the Networ k R eply Data for mat The connection ID (the data is same as the connection ID data on the sending data format) is attached to the RS-232C commands reply data.
38 Command Control via the Networ k Automa tic Connection Break The TCP connection will be automatically disconnected after there is no communication for 30 seconds after being established. Authentication The projector does not accept commands without authentication success when authentication is enabled.
1 About The Symbols V arious symbols are used in this manual, the user ’s manual and on the product itself to ensure correct usage, to prevent danger to the user and others, and to prevent property damage. The meanings of these symbols are described below .
2 Safety Precautions W ARNING Never use the projector if a problem should occur . Abnormal operations such as smoke, strange odor , no image, no sound, excessive sound, damaged casing or el ements or cables, penetration of liquids or foreign matter , etc.
3 W ARNING Be cautious of High temperatures of the projector . High temperatures are generated when the lamp is lit. It could result in fire or burn. Use special caution in households where children are present. Do not touch about the lens, air fans and ventilation openings during use or immediately after use, to prevent a burn.
4 W ARNING Be careful in handling the light source lamp. The projector uses a high-pressure mercury glass lamp made of glass. The lamp can break with a loud bang, or burn out. When the bulb bursts, it is possible for shards of glass to fly into the lamp housing, and for gas containing mercury to escape from the projector ’s vent holes.
5 Safety Precautions (continued) CAUTION Be careful in moving the projector . Neglect could result in an injury or damage. • D o no t mo v e th e pr o j e c t o r du r in g u se . B e f or e m ov i n g , di s c o n n e c t th e power cord and all external connections, and close the slide lens door or attach the lens cap.
6 Safety Precautions (continued) NOTE Do not give the remote control any physical impact. A physical impact could cause damage or malfunction of the remote control. • T ake care not to drop the remote control. • Do not place the projector or heavy objects on the remote control.
7 Safety Precautions (continued) NOTE About consumables. Lamp, LCD panels, polarizors and other optical components, and air filter and cooling fans have a different lifetime in each. These parts may need to be replaced after a long usage time. • This product isn’t designed for continuous use of long time.
8 • If the lamp should break (it will make a loud bang when it does), unplug the power cord from the outlet, and make sure to request a replacement lamp from your local dealer.
9 Regulatory Notices FCC Statement W arning W ARN ING: Th is e quipm ent has been tested and fou nd to compl y wi th t he l imits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
2900 Dukane Drive St. Charles, Illinois 60174 www .dukcorp.com/av T oll-free: 800-676-2487 Fax: 630-584-5156 e-mail: avsales@dukcorp.com Audio Visual Products #401-8755E-01.
Een belangrijk punt na aankoop van elk apparaat Dukane 8943 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Dukane 8943 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Dukane 8943 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Dukane 8943 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Dukane 8943 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Dukane 8943 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Dukane 8943 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Dukane 8943 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.