Gebruiksaanwijzing /service van het product XD-DW7U van de fabrikant Aiwa
Ga naar pagina of 54
ESP AÑOL FFF FRANÇAIS ESP AÑOL ENGLISH XD-DW7 U XD-DW5 U OPERA TING INSTRUCTIONS INSTRUCCIONES DE MANEJO MODE D'EMPLOI POR T ABLE DVD PLA YER REPRODUCT OR POR TÁTIL DE DVD LECTEUR DE DVD POR .
CORRECTION Please note the f ollowing corrections to the Operating Instructions: P ag e 43 Y ou do not remember the code number set in “Ratings”. INCORRECT s b TITLE b RETURN b Q SURROUND CORRECT .
ENGLISH Precautions To maintain good performance • Do not use the unit in places which are extremely hot, cold, dusty or humid. In particular, do not use or keep the unit in the following places.
Note on condensation If the unit is suddenly moved from a cold place to a warm one, it may result in condensation on the pickup lens causing malfunction or playback difficulties. Should this occur, leave the unit for a few hours, then try playback again.
Parts and controls PREPARATIONS Main unit (front and right side) 1 Liquid crystal display Do not push the liquid crystal display hard. 2 Stereo speakers 3 i OPEN button 4 Remote sensor 5 Displa y wind.
Main unit (left side) 12 Display window 1 DC IN 9V jack 2 i DISC OPEN por tion 1 Pla yback indicator 2 D VD indicator 3 Q SURROUND indicator 4 Angle indicator 5 Repeat pla yback indicators } : Disc re.
5 ENGLISH Remote control 2 3 1 4 6 7 8 9 0 ! @ # $ % ^ & * ( ; ] [ ) - ' 5 = 1 PROGRAM b utton 2 MARK button 3 0-9 buttons 4 +10 button 5 T OP MENU button 6 j , l , i , k , ENTER buttons 7 v.
Remote control Installing batteries Detach the battery cover on the rear of the remote control, and insert two R6 (size AA) batteries with 0 and 9 aligned correctly. When to replace the batteries The maximum operational distance between the remote control and the sensor of the units should be approximately 5 meters (16 feet).
7 ENGLISH Using the battery pack Charging the battery pack Charge the battery pack fully at the first time of use. Two adaptors are supplied with this unit. To recharge the battery pack, use the larger one (AC-D920U). Do not recharge the battery pack when it is connected to the DVD player.
When recharge is finished The charge lamp turns off. After making sure the indicator is turned off, disconnect the AC adaptor and the supplied power cord. Time to recharge the battery The battery indicator changes the indication based on the remaining power in the battery as follows: Recharge the battery when appears.
Connecting the battery pack to the unit Fit the claws of the battery pack into the latch slots on the bottom of this unit. Push the battery pack up and into the latch slots as shown below.
Slide POWER switch on the main unit toward ON to turn the power on. The power indicator lights. The power cannot be turned on by POWER of the remote control. When using with the battery pack, the power may not be turned on at once. In this case, turn the power on again after 3 seconds.
When the menu screen is displayed The menu screen may be displayed first after loading a DVD or video CD 2.0 with PBC ON which contains a menu. You cannot select the program in the menu screen while the on screen display appears. Turn off the on screen display before playing a disc.
About the symbol display The symbol will be displayed on the screen if your operation is prohibited by the unit or the disc. Removing the disc Caution Make sure that the disc stops and is completely still before you remove the disc. If you touch the spinning disc, you may hurt your finger.
Playing back (continued) Still (Pause) Press a during playback. To return to normal playback Press c (Play) or a . NOTE This unit remembers the point at which playback was paused. Fast Forward, Reverse Press f or g on the remote control during playback.
Skipping Press r or t during playback. • Skip to the next chapter or track: t The disc position advances one chapter or track each time the button is pressed.
Information about On Screen Display (OSD) This unit features OSD Menu Icons showing disc information (title/chapter/track number, elapsed playing time, audio/subtitle language, angle, and sound) and player information (repeat play, play mode, marker, etc.
1 2 3 4 5 Cancel (Normal display) 1 shows the track number. (See page 16.) While playing a video CD Version 2.0, if the “ -- ” appears instead of the track number, the PBC function is set to ON. 2 shows the elapsed playing time during playback. 3 shows the audio information (Video CD only).
While playing, press DISPLAY on the main unit or ONSCREEN DISPLAY ON/OFF on the remote control repeatedly. The menu icons are displayed. To operate with the T-SEARCH button Press T-SEARCH on the remote control while playing. Then go to step 2. Press j or l to select the “ Chapter search ” icon.
With a DVD which allows displaying of elapsed time, you can specify a time on the disc to search for a desired location. While playing, press DISPLAY on the main unit or ONSCREEN DISPLAY ON/OFF on the remote control repeatedly. The menu icons are displayed.
To memorize the points While playing, press DISPLAY on the main unit or ONSCREEN DISPLAY ON/OFF on the remote control repeatedly. The menu icons are displayed. To memorize the points with the MARK button Press MARK on the remote control while playing.
To restart play from the memorized point While the “ Mark function ” icon is displayed, press j or l to select a point. You can also use the number buttons (1-5) to select a point. Press c (Play) to start play. To restart play from the memorized point with the MARK button 1 Press MARK while playing.
Press j or l to select the “Playback mode” icon, then press i or k to select “PRG”. Press ENTER. A programing screen is displayed on the display. Press j or l to select the number of the track you want to program. Then press ENTER. If you enter the wrong number Press C to delete the number.
To delete a programed track On the programing screen, select “ C ” with j or l . Then press ENTER. The last programed number is canceled. You can also delete the last program with C on the remote control. To clear the programed contents At the programing screen, select “ AC ” with j or l .
Repeat playback Either when playing, or while the resume function is active, press DISPLAY on the main unit or ONSCREEN DISPLAY ON/OFF on the remote control repeatedly. The menu icons are displayed. Press j or l to select the “ Repeat playback ” icon.
Repeating a Video CD with PBC off /an audio CD Either when playing, or while the resume function is active, press DISPLAY on the main unit or ONSCREEN DISPLAY ON/OFF on the remote control repeatedly. The menu icons are displayed. Press j or l to select the “ Repeat playback ” icon.
When playing a DVD which has been recorded in multi-angle (photographed from several different angles), you can select which angle you would like to view the action from. When a multi-angle scene comes on during playback, the indicator will be displayed on the display window to let you know that you can change the angle.
Displaying and changing subtitles When playing discs which contain subtitles, you can display the subtitles on the screen or change the language of the subtitles. Displaying subtitles While playing, press DISPLAY on the main unit or ONSCREEN DISPLAY ON/OFF on the remote control repeatedly.
Changing the audio track Some DVDs have more than one audio track, such as soundtracks with different languages. While playing such a disc, you can change the audio track to hear the different soundtracks. While playing, press DISPLAY on the main unit or ONSCREEN DISPLAY ON/OFF on the remote control repeatedly.
Video CD karaoke: Either when playing, or while the resume function is active, press DISPLAY on the main unit or ONSCREEN DISPLAY ON/OFF on the remote control repeatedly. The menu icons are displayed. Press j or l to select the “ Audio track ” icon.
Selecting Q surround (DVD) Even when only two speakers are used for the left and right, Q SURROUND makes the sounds rich and wide as if you are surrounded by two front speakers and two rear speakers.
Changing setup values SET UP OPERATION 1 2 3 Basic operations Your DVD player comes from the factory with all the basic items set properly. Change any other settings according to your individual setup and preferences. Press SET UP while the player is stopped.
Changing setup values (continued) Use i or k to move the cursor (the yellow area) to the desired setting. Press ENTER. The selected setting will be saved, and the main setup screen of step 1 will be displayed again. However, for some settings the screen will display a more detailed menu instead.
Disc Languages Sets the language for displaying DVD disc menus. There are 3 items you can set. Audio Language: 1 At the initial setting screen, select “ Disc Languages ” by using i or k . Then press ENTER. 2 Use i or k to move the cursor (the yellow area) to select “ Audio language ” .
Subtitle Language: 1 At the initial setting screen, select “ Disc Languages ” by using i or k . Then press ENTER. 2 Use i or k to move the cursor (the yellow area) to “ Subtitle Language ” . 3 Press ENTER. 4 Use i or k to move the cursor (the yellow area) to the desired language.
Disc Menu: 1 At the initial setting screen, select “ Disc Languages ” by using i or k . Then press ENTER. 2 Use i or k to move the cursor (the yellow area) to “ Disc Menu ” . 3 Press ENTER. 4 Use i or k to move the cursor (the yellow area) to the desired language.
TV Aspect There are 2 options for the television aspect ratio. When your television is connected to this unit with the connecting cable has a conventional size screen (4:3), refer to “ NORMAL TV ” . If the connected TV has a wide-screen (16:9), refer to “ WIDE TV ” .
Ratings Caution In some discs, the rating level mentioned on the disc label is not registered inside the disc. To check whether the lock setting is functional in this unit, carry out the lock setting procedures. 1 At the initial setting screen, select “ Ratings ” by using i or k .
PBC Sets the default PBC (Play back control) mode on or off for playing a video CD with PBC function. 1 At the initial setting screen, select “ PBC ” by using i or k . Then press ENTER. 2 Use i or k to move the cursor (the yellow area) to “ ON ” or “ OFF ” .
CONNECTION Connecting to external equipment Before connecting • Turn off the power of this unit and the equipment to be connected. • Refer to the instructions for the equipment to be connected. Connecting to a wide TV/an AV TV According to the type of connected TV, set the initial TV mode referring to “TV Aspect” on page 35.
Connecting to audio equipment without digital audio input terminals Connecting to audio equipment with digital audio input terminals To AUDIO/OPT OUT jack To audio input jacks Audio connecting cable (.
Connecting to an active speaker system To audio input jacks Audio connecting cable (supplied) CONTINUE ∗ 2 When a 96 kHz-24 bit disc is played, the audio signals are output in 48 kHz-16 bit. ∗ 1 This changes condensed audio signals to PCM and outputs them.
Connecting to a dolby digital (AC-3) decoder During playback of a DVD recorded in Dolby Digital (AC-3)/5.1ch surround, bit streams of Dolby Digital are output from the optical audio output terminals of this unit. By connecting to a dolby digital decoder, you can enjoy theater-quality realistic audio sound right in your own home.
Connecting to a video camera You can enjoy contents of an external video camera through the liquid crystal display and stereo speakers of this unit. To set to the color system of connected equipment Slide the PAL/NTSC switch on the right side according to the color system of connected equipment.
OTHERS T roubleshooting If something seems to be wrong with your DVD player, first check the items in the table below. 43 ENGLISH General The power does not turn on. • Connect the AC adaptor correctly or insert the battery pack correctly. (page 6-9) • Check that POWER switch is not set to HOLD.
ENGLISH 44 Operations Playback does not start by pressing c (Play). Playback stops immediately. • The player is affected by condensation. (page 2) Wait approximately one or two hours. • If the disc is dirty, wipe it with a cleaning cloth. • Insert the disc correctly with the label side up.
Code Language Code Langua ge Code Language 6565 Af ar 7285 Hungarian 8084 P ortuguese 6566 Abkhazian 7289 Armenian 8185 Quechua 6570 Afrikaans 7365 Interlingua 8277 Rhaeto-Romance 6577 Amharic 7378 In.
Interactive DVD With this DVD disc, the story is changeable by user's selection, and/or the direction of view is changeable. Title, chapter (DVD) A DVD disc is divided into large parts (title) and smaller parts (chapter). Each part has a number which is called title number or chapter number.
Specifications Main unit Power supply DC 9 V Power consumption 18 W Weight Main unit: 670 g (23.5 oz) Battery pack: 560 g (19.6 oz) External dimensions XD-DW7: 195 (W) × 26.9 (H) × 144 (D) mm (7 3 / 4 × 1 1 / 16 × 5 3 / 4 in.) XD-DW5: 195 (W) × 31.
• Manuf actured under license from Dolby Laboratories. “ Dolby ” and the doub le-D symbol are trademarks of Dolby Laboratories. Confidential unpublished works. c 1992-1997 Dolby Laboratories . All rights reserved. • Manuf actured under license from Digital Theater Systems, Inc.
Playbac k of a CD-R/CD-R W A CD-R/CD-RW ma y not be play ed back because its reflectance is low er than a CD . In addition, pla yback ma y not be carr ied out because of a disc’ s condition, a spot, a scratch, condensation on the pic k up lens, etc.
CA UTION <Note for CD-R/R W playback> This unit cannot pla y any CD-R/R W disc. Some CD-R/R W discs ma y be pla yed bac k, ho we v er , we do not guarantee their operations.
When listening with headphones Important Y ou must use the supplied e xtension cab le to suit to the P art 15 of the FCC r ules, when listening with headphones (not supplied). T o connect y our headphones (1) Connect headphones (not supplied) to the supplied extension cab le .
8A-HU1-901-01 000613ATN-Y0 Printed in Japan.
Een belangrijk punt na aankoop van elk apparaat Aiwa XD-DW7U (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Aiwa XD-DW7U heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Aiwa XD-DW7U vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Aiwa XD-DW7U leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Aiwa XD-DW7U krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Aiwa XD-DW7U bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Aiwa XD-DW7U kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Aiwa XD-DW7U . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
