Gebruiksaanwijzing /service van het product DX-WD1202 van de fabrikant Dynex
Ga naar pagina of 23
ASSEMBL Y INSTRUC TIONS D X - WD1202 Corner T V Stand Safety information and specifications ............ 2 T ools needed . ........................................................... 3 P ack age contents ...............................................
2 DX-WD1202 Need help? Call 800-305-2204 Safety inf ormation and specifica tions Wa r n i n g s • Do not let children climb on your stand or play near it.
3 DX-WD1202 Need help? Call 800-305-2204 Package co ntents P ackage contents: hardware Note: Y ou may receive ex tra hardware with your ne w T V stand. Make sure you hav e all the hardware ne cessary to assemble your new T V stand: To o l s n e e d e d Hammer No .
4 DX-WD1202 Need help? Call 800-305-2204 P ackage contents: hardwar e (continued) Using a screw that is too long wi ll cause damage to your stand. Bef ore beginning assembly , separate each type of screw . Carefully study the screw tabl e below . Y ou can use the rule r at the bottom of the screw table to measur e screws .
5 DX-WD1202 Need help? Call 800-305-2204 P ackage contents: par ts A End (2) E Bottom (1) F Shelf (1) B Upright (1) C Lo wer upright (1) D To p ( 1 ) G Back (1) H Door (2) I Right fro nt and left rear.
6 DX-WD1202 Need help? Call 800-305-2204 Assembly instructions Step1: Assemble your stand on a carpet ed fl oor or on the empt y car ton to av oid scratching your stand or the floor . Push thirt y hidden cams ( Q ) into the ends ( A ), uprights ( B and C ), t op ( D ), bottom ( E ), shelf ( F ), and one set of legs ( I and J ).
7 DX-WD1202 Need help? Call 800-305-2204 T ightening hidden cams In the re maining steps, use these illustrations f or in structions on tightening hidden cams. Wa r n i n g : Risk of damage or injur y . Hidde n cams must be completely tightened. Hidden cams that are not completely tightened will loosen, and parts may separate.
8 DX-WD1202 Need help? Call 800-305-2204 Step 2: Sc rew two c am scre ws ( S ) into each of the legs (two I and two J ). Place the ends ( A ) flat with the side with the hidden cams facing up. Make sure that the sides of the legs wi th the hidden cams ar e towar d the ends ( A ).
9 DX-WD1202 Need help? Call 800-305-2204 Step 3: Carefully turn the ends ( A ) over so the side without the hidden cams is facing up. Use a Phillips screw driver to screw ei ght black 9/16" flat head scr ews ( FF ) (four per end) into the ends ( A ) until the shoulders of the screws r est on the sur face of the ends.
10 DX-WD1202 Need help? Call 800-305-2204 Step 4: Careful ly turn the ends over so the sides with the hidden cams fac e up. Attach the unattached leg ( I ) to the left end ( A ) and the unattached leg ( J ) to the right end ( A ). See Step 2 for instructions.
11 DX-WD1202 Need help? Call 800-305-2204 Step 5: F asten the stop molding ( L ) to the top ( D ). Use a flatblade screw driver to tight en the four hidden cams .
12 DX-WD1202 Need help? Call 800-305-2204 Step 6: F asten the upright ( B ) and the left end ( A ) with the leg ( J ) to the top ( D ) and stop molding ( L ). Use a flatblade screwdriver to tighten the five hi dden cams (two on the upright ( B ), two on the left end ( A ), and one on the leg ( J )).
13 DX-WD1202 Need help? Call 800-305-2204 Step 7: F asten the shelf ( F ) to the left end ( A ). Use a flatblade screw driver to tight en the two hidden cams. See “Tight ening hidden cams” on page 7. F asten the shelf ( F ) to the upright ( B ). Use a Phillips scr ewdriver and tw o black 1 7/8" flat head scr ews ( DD ).
14 DX-WD1202 Need help? Call 800-305-2204 Step 8: F asten the bottom ( E ) to the left end ( A ). Use a flatblade screwdriv er to tighten the two hidden cams. See “Tightening hidden cams” on page 7. F asten the bottom ( E ) to the lower upright ( C ).
15 DX-WD1202 Need help? Call 800-305-2204 Step 9: F asten the right end ( A ) with the leg ( I ) to the top ( D ), bottom ( E ), shelf ( F ), and stop molding ( L ). Use a flatblade screw driver to tighten the seven hidden cams: A (2), E (2), F (2), and I (1).
16 DX-WD1202 Need help? Call 800-305-2204 Step 10: With the t op of the unit facing down, fasten the foot base ( U ) to the extension block ( K ). Use a Phillips screwdriver and f our black 9/16" pan head screws ( GG ). Then, push the foot ( T ) into the f oot base ( U ).
17 DX-WD1202 Need help? Call 800-305-2204 Step 11: Carefully turn the unit so the fr ont is facing down, then fasten the back ( G ) to the legs ( I and J ). Use a Phillips screwd river and eight br own 7/16" large head scr ews ( II ). F asten the remaining back ( G ) to your st and using 33 nails ( KK ).
18 DX-WD1202 Need help? Call 800-305-2204 Step 12: F asten the hinges ( V ) to the doors ( H ). Use a Phillips screw driver an d eight 1/2" flat head screws ( HH ) (two for each hinge).
19 DX-WD1202 Need help? Call 800-305-2204 Step 13: Carefully turn the unit so the left end is facing down, then fast en one of the doors ( H ) t o the left end ( A ). Use a Phillips screw driver and the screw s in the hinges. Note: Y ou may need to loosen the mounting screw to slide the hi nge par t way out of the slot.
20 DX-WD1202 Need help? Call 800-305-2204 Step 14: Y ou may need to adjust the door s to make them fit correctly . T o adjust the doors from side to side (horizontal), lo osen the mounting screw sev eral turns, then turn the horizontal adjusting screw in or out.
21 DX-WD1202 Need help? Call 800-305-2204 Step 15: Apply the warnin g label ( BB ) to the top ( D ). Y ou should be able to read the label when the T V is r emoved from your stand . When the T V is in place , it should hi de the label. P eel off the back ing and ap ply the label as shown.
22 DX-WD1202 Need help? Call 800-305-2204 Still need help? F or customer ser vice, call: 800-305-2204 (U.S./C anada markets) Distributed by Best Buy P urchasing , LL C 7601 P enn Av enue South, R i chfield, MN USA 55423-3645 © 2011 BBY Soluti ons, Inc.
ww w .dynexproducts.com (800) 305-2204 Distributed by Best Buy Purchasing , LL C 7601 Penn A ve. South, Richfield, MN 55423 U .S.A. © 2011 BBY Solutions, Inc. All rights reser ved. DY NEX is a trademark of BBY Solutions, Inc. Regist ered in some countries.
Een belangrijk punt na aankoop van elk apparaat Dynex DX-WD1202 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Dynex DX-WD1202 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Dynex DX-WD1202 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Dynex DX-WD1202 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Dynex DX-WD1202 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Dynex DX-WD1202 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Dynex DX-WD1202 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Dynex DX-WD1202 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
