Gebruiksaanwijzing /service van het product P10 van de fabrikant Earthquake Sound
Ga naar pagina of 16
MiniMe P10 & P12 Models Earthquake Sound Corporation www .earthquakesound.com Sound That Will Move Y ou User's Manual.
Safety Instructions 13. Damage Requiring Service — The Component 1. Read Instructions — All the safety and operation should be served only by EQ qualified serviced instructions should be read before the Earthquake personnel when: Component is operated.
W ARNING: The MiniMe subwoofers are capable of generating high sound pressure levels. Y ou should exercise caution when operating these speakers. Long term exposures to high levels of sound pressure will cause permanent damage to your hearing.
Introduction Please take a moment to fill out and mail the Earthquake W arranty Registration card. Also read the serial number located on the control panel and record it here: Unpacking Y our Earthquake subwoofer should reach you in perfect condition.
(1) Line Level RCA Inputs terminals will accept up to 16-gauge quality speaker Connect with RCA type patch cords to the line level wire. The Inputs should be connected to the left and output of your receiver or pre-amp. If your pre- right speaker terminals of your amplifier or receiver .
(6) Auto ON/OFF (10) Sub Operation Switch When the main “POWER” ON/OFF switch is in the In LFE position, the Frequency adjustment becomes “OFF” position, this switch has no affect on the disabled and the subwoofer runs in a Full range subwoofer .
• Do not let anything come into contact with the panel Installation and keep at least two inches away from any walls. Observe the following general precautions and read the safety instructions before powering your The metal control plate serves as the amplifier heat Earthquake subwoofer .
AC outlets on the same circuit breaker Power strip T ape Deck DVD Pre-amplifier Amplifier Subwoofer Connections • This diagram shows all the low power components Please consider the following when setting up sharing a power strip which is connected to the same your new system: outlet used by the amplifier .
MiniMe 1 P= Passive Radiator A= Active Driver MiniMe 2 P A MiniMe 3 P A Location F a c t : S u b w o o f e r s r e p r o d u c e f r e q u e n c i e s w i t h #1 is very good positioning. wavelengths that are long in relation to the dimensions of most living rooms.
System Configurations The following pages show some typical connections that you might make in your installation. They show how the inputs and outputs of the Earthquake sub are connected to your pre-amplifier or receiver .
Connections to a pre-amplifier using “Y” cables If your pre-amplifier does not have a sub/LFE output, you can use “Y” cables to send its main outputs to both the subwoofer and your amplifier . The subwoofer will play the low frequency range and your front speakers will play the full range.
Earthquake Sound, 2727 McCone Avenue, Hayward, CA 94545 USA www.earthquakesound.com VOLUME FREQUENCY MODE PHASE AUTO MIN 50Hz MAX RIGHT POWER LEFT 160Hz SUB 0 OFF LFE 180 ON 110-120VAC~60Hz 220-240VAX~50Hz FUSE: 115V , T6.
AUTO OFF ON VOLUME FREQUENCY MODE PHASE MIN 50Hz MAX 160Hz SUB 0 LFE 180 Adjusting the controls There are two main methods for adjusting the level, crossover frequency and phase of the Earthquake MiniMe to match a system. ? Method One: T ypical: Listening and making adjustments to suit your taste.
MiniMe P10 Specifications MiniMe P12 Specifications Amplifier Output Amplifier Output 600 W atts (4-Ohm impedance) 600 W atts RMS (4-Ohm impedance) High Cut Filter High Cut Filter 50Hz-160Hz adjustable.
Limited 5-Y ear W arranty Earthquake warrants the original purchaser that all Factory Sealed New Audio Products to be free from defects in material and workmanship under normal and proper use for a period of five (5) years from the date of purchase (as shown on the original bill of sale with serial number affixed/written on it).
Earthquake Sound Corporation 2727 Mc Cone A venue, Hayward, California 94545 Ph (510) 732-1000 Fax (510) 732-1095 www .earthquakesound.com.
Een belangrijk punt na aankoop van elk apparaat Earthquake Sound P10 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Earthquake Sound P10 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Earthquake Sound P10 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Earthquake Sound P10 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Earthquake Sound P10 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Earthquake Sound P10 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Earthquake Sound P10 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Earthquake Sound P10 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
