Gebruiksaanwijzing /service van het product EA300PRO-800 van de fabrikant East
Ga naar pagina of 20
Line Interactive Sinewave UPS 800 /1.1 K/ 1.5 K/ 2K/2.5K/3K VA Uninterruptible P ower Supply S ystem User Manual.
1 T able of Contents 1. Important Safety Warning……………… ………… …………………… 2 1-1. T r ansportati on 2 1-2. Prepar ation 2 1-3. Installation 2 1-4. O perati on 2 1-5. Maintenanc e, Service And F aults 3 2. Installa tion And S etup……… …………… …………………… ………… 4 2-1.
2 1. Importan t Safety Warnin g Please comply with all warnings and operatin g instructions in this manual strictly. Save this manual pro perly and read carefully the following instructions bef ore installing the unit. Do not operate this unit before reading through all safety information and operating instructions carefully 1-1.
3 1-5. Maintenance, Service And Faults The UPS system operates with hazardous voltages. R epairs may be carried out only by qualified maintenance personnel.
4 2. Installation An d Setup NOTE: Before installation, please inspect t he unit. Be sure that nothing inside the package is damaged. Please keep t he original package in a safe p lace for future use. 2-1 . Rear Panel View 800 /1. 1K /1.5K/2K IEC Type 2.
5 2-2. Install The UPS F or safety consider ation, the UPS is shipped out from fact ory without connecting battery wires. Before install the UPS, p lease follow below steps to re -connect battery wires f irst. Step 1 Step 2 Step 3 R emove front pa ne l.
6 Step 3: Communication connection Communication ports: USB port RS -232 port Intelligent slot T o allow for unattended UPS shutdo wn/start-up and status monitoring, connect the communication cable one end to the USB/RS- 232 port a nd the other to the communication port of your PC.
7 Step 7: Turn on the UPS Press the ON/Mute button on the front panel for two seconds to power on t he UPS. Note: The battery charges fully during the first five hours of normal operat ion. Do not expect full battery run capability during this initial charge p eriod.
8 2-5 Battery Kit Assembly ( option) NOTICE: Please assemble battery kit f irst before installing it inside of UPS. Please select correct batt ery kit procedure below to assemble it. 2-battery kit Step 1: R e mov e adhesive tapes. Step 2: Connect all battery terminals b y following below chart.
9 6-battery kit Step 1: R e mov e adhesive tapes. Step 2: Connect all battery terminals b y following below chart. Step 3: Put assembled battery packs on one side of plastic shells. Step 4: Co ver the other side of plastic shell as below chart. Then, battery kit is assembly well.
10 3. Operations 3-1. Button Operation Button Function ON/MUTE Button Turn on the UPS: Press and hold ON/Mute button for at least 2 seconds to turn on the UPS. Mute the alarm: After the UPS is turned on in battery mode, press and hold this button for at least 5 seconds to disable or ena ble the alarm system.
11 Display Function Backup time information Indicates the backup time in pie chart. Indicates the backup time in numbers. H: hours, M: minute Warning & Fault information Indicates that the warning and fault occurs. Indicates the warning and fault codes, a nd the codes are listed in details in 3-5 section.
12 3-4. LCD Display Wordings Index Abbreviation Display content Meaning ENA Enable DIS Disable ESC Escape EP EPO FA F an TP T emperat ure CH Charger RAC Rack displa y T OE T ower display SF Site F ault 3-5. UPS Setting There are two p ar ameters to set up the UPS.
13 03: Progr ammable outlets setting Interface Setting Setting the backup time limits in minutes from 0-999 for programmable outlets which connect to non-critical devices on battery mode. 04 : LCD display direction set ting Interface Setting RAC: the LCD d isplay is horizontal.
14 Step 4: Press the “ Up “ butt on (ON/MUTE) again to switch to "03" of progr am lis t . Then press “E nter “ button for setting progra mmable outlet time. P us h “Up” button to change the value of backup time according your demand.
15 Operating mode Description LCD display Standby mode UPS is powered off and no output supply power, but still can charge batteries. 3-7. Faults Reference Code F ault event F ault code Icon F ault ev.
16 4. Troubleshoo ting If the UPS system does not oper ate correctly , please solve the problem by using the ta ble be low . Symptom Possible cause Remedy No indication and alarm even though the mains is normal. The AC input power is not connected well.
17 Sy mptom Possible cause Remedy F ault code is shown as 1, 2, 3, 4, 11, 12, 13 and 41 on L CD display and alarm is continuously sounding. A UPS internal fault has occurred. Contact your dealer Battery backup time is shorter than nominal v alue Batteries are not fully charged Charge the bat teries for at least 5 hours and then check capacity .
18 5. Storage and M aintenance 5-1. Operation The UPS s ystem contains no use r-se rviceable parts. If the battery service lif e (3~5 years at 25°C ambient temperature) has been exceeded, the b atteries must be replaced. In t his case, please contact your dealer.
19 MODEL 800 1.1K(L) 1.5K 2K (L) 2. 5K 3K (L) CAPAC ITY 800 VA / 640 W 1100 VA / 880 W 1500 VA / 1200 W 2000 VA / 1600 W 2500 VA / 2000 W 3000 VA / 2400 W INPUT Acceptable Vol tage Range 81 -145 VAC o.
Een belangrijk punt na aankoop van elk apparaat East EA300PRO-800 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen East EA300PRO-800 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens East EA300PRO-800 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding East EA300PRO-800 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over East EA300PRO-800 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van East EA300PRO-800 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de East EA300PRO-800 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met East EA300PRO-800 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
