Gebruiksaanwijzing /service van het product CS-300, CS-340, CS-345 van de fabrikant Echo
Ga naar pagina of 24
X7503203102 X750003241 04/03 Chain Saw Instruction Manual MODELS : CS-300 Serial Number 03001001 - 03999999 CS-340 Serial Number 03001001 - 03999999 CS-345 Serial Number 03001001 - 03999999 W ARNING DANGER Read rules for safe operation and instructions carefully.
2 RULES FOR SAFE OPERA TION A. Kickback Safety Precaution for Chain Saw Users W ARNING! KICKBACK may occur when the nose or tip of the guide bar touches an object, or when the wood closes in and pinches the saw chain in the cut.
3 CONTENTS Page Rules for Safe Operation .................................................................................................. 2 T echnical Dat a ............................................................................................
4 TECHNICAL DA T A * T echnical data subject to change without notice. l e d o M 0 0 3 - S C0 4 3 - S C5 4 3 - S C n o i s n e m i DH x W x L m m0 2 2 x 5 3 2 x 0 6 25 4 2 x 5 3 2 x 0 8 3 h c n i7 . 8 x 2 . 9 x 2 . 0 16 . 9 x 2 . 9 x 0 . 5 1 t h g i e Wy r d , d a e h r e w o Pg k) b l 1 .
5 DESCRIPTION The ECHO product you purchased has been factory pre-assembled for your convenience. Due to packaging restrictions, guide bar and saw chain installation and other assembly may be necessary. After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or missing parts.
6 1. Hand guard (Chain brake actuating lever) 2. Throttle control lockout 3. Throttle control trigger 4. Sprocket guard 5. Chain catcher 6. Air cleaner cover 7. Purge bulb 8. Guide bar 9. Saw chain 10 . Front handle 1 1 . On / Off switch 12 . Rear hand guard 1 3 .
7 B A PREP ARA TION FOR USE UP The machine may be delivered with guide bar (A), tip guard, and saw chain (B) separated. Install guide bar , tip guard, and saw chain as follows: W ARNING DANGER Saw Chain is sharp! Always wear gloves when handling assembly, otherwise serious personal injury may result.
8 FUEL ST A TEMENT GASOLINE - Use 89 Octane [R+M/2] (mid grade or higher) gasoline or gasohol known to be good quality. Gasohol may contain up to 10% Ethyl (grain) alcohol or 15% MTBE (methyl tertiary-butyl ether). Gasohol containing methyl (wood) alcohol is NOT approved.
9 CS-345 CS-300 CS-340 A A B C Securely hold the saw. OPERA TION WHEN THE ENGINE IS COLD • Move chain brake lever fully forward to engage chain brake before starting. • Fill the fuel tank with fuel. • Fill the chain oil tank with lubricant. • Turn switch (A) to “RUN” position.
10 ST ARTING W ARM ENGINE • Ensure that there is fuel and chain oil in the tanks. (If fuel tank was emptied during previous operation, refill tank and push purge bulb 10 times.) • Turn switch (A) to “RUN” position. • Pull starter handle. • Choke may be used if necessary , but be sure to push it back on first firing sound.
11 Kickback CUTTING INSTRUCTIONS GENERAL [NOTE] Read the ECHO “CHAIN SAW SAFETY MANUAL” included with your chain saw for additional cutting and safety instructions.
12 2” 45° 2” CAUTION A falling tree can seriously damage anything it may hit - a car , a house, a fence, a power line, or another tree. There are ways to make a tree fall where you want it, so first decide where that is! Before cutting, clear the area around the tree.
13 Don’t cut with the saw overhead or the bar in a vertical posi- tion. If the saw should kick back you may not have good enough control to prevent possible injury . Bucking is the sawing of a log or fallen tree into smaller pieces. There are a few basic rules which apply to all bucking operations.
14 INFORMA TION Kickback Safety Features The following features are recommended for this model as Kickback Safety Features. • Double Guard Low Kick T ype Guide Bar or Asymmetrical Low Kick T ype Guide Bar Note: Y our saw chain can be equipped with either of these bars.
15 MAINTENANCE AND CARE AIR FILTER • Check before every use. • Pull choke (A) all the way out (close position). • Loosen bolt and remove air cleaner (B) cover and filter (C).
16 SPARK PLUG • Check periodically • Gap = 0.65mm (.026 in.) • Replace if either electrode is worn, or if the insulator is fouled by oil or other deposits. • Torque = 145 – 155 kg*cm (125 – 135 in. lb.) CAUTION : Do not over-torque. COOLING SYSTEM CLEANING • Remove spark plug lead.
17 B A Before starting the unit for adjustment, check the follow- ing items: • The correct spark plug must be clean and properly gapped. • The air filter element must be clean and properly installed. • The muffler spark arrestor screen and exhaust port must be clear of carbon.
18 W ARNING DANGER Use of replacement saw chain and/or guide bar other than that specified, or operation without the “tip guard” in place, may cause severe kickback resulting in serious injury. Only use saw chain designated as, “LOW-KICKBACK,” that meets the ANSI B175.
19 30° 85° 60° 91 0.64 mm (0.025”) Parallel Number indicates Chain type Number indicates Chain type 91S (SPROCKET) (DRIVE LINK) • Properly filed cutters are shown below .
20 Fuel is not reaching carburetor Fuel is not reaching cylinder Engine does not start (or, is difficult to start) Engine cranks There is fuel in the tank Fuel is reaching carburetor Fuel is reaching cylinder There is spark at high tension cord end There is spark at plug Starting procedures correct No spark at high tension cord end.
21 Improper fuel used ........................................ Use fuel with correct mixing ratio. Never use gasoline of poor quality. Spark plug defective (worn) .
22 Kickback Motion: • When the bar nose hits another tree, etc. • Improper thrust cutting. CORRECT USE OF CHAIN BRAKE The installation of a chain brake may be mandatory by law or as stipulated by insurance regulations in your area of operation.
23 NOTES.
CONSUMER PRODUCT SUPPORT 1-800-673-1558 8:30 - 4:30 Mon - Fri C.S.T. ECHO, INCORPORA TED 400 O AKWOOD R OAD L AKE Z URICH , IL 60047 www .echo-usa.com SER VICING INFORMA TION P ARTS Genuine ECHO Parts and ECHO REPOWER TM Parts and Assemblies for your ECHO products are available only from an Authorized ECHO Dealer.
Een belangrijk punt na aankoop van elk apparaat Echo CS-300, CS-340, CS-345 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Echo CS-300, CS-340, CS-345 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Echo CS-300, CS-340, CS-345 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Echo CS-300, CS-340, CS-345 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Echo CS-300, CS-340, CS-345 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Echo CS-300, CS-340, CS-345 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Echo CS-300, CS-340, CS-345 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Echo CS-300, CS-340, CS-345 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
