Gebruiksaanwijzing /service van het product PPT-265S van de fabrikant Echo
Ga naar pagina of 36
Power Pruner TM Operator's Manual MODEL: PPT -265S W ARNING X770001241 09/08 X7702092901 Read rules for safe operation and instructions carefully . ECHO provides an Operator's Manual and a Safety Manual. Both must be read and understood for proper and safe operation.
2 Copyright© 2008 By Echo, Incorporated All Rights Reserved. I n t r o d u c t I o n W elcome to the ECHO family . This ECHO product was designed and manufactured to provide long life and on-the-job dependability . Read and understand this manual and the SAFETY MANUAL you found in the same package.
P o w e r P r u n e r TM o P e r a T o r ' s M a n u a l 3 s a f e t y m a n u a l s a f e t y s y m b o l s a n d I m p o r t a n t I n f o r m a t I o n Hot Surface Symbol description/application Symbol form/shape Symbol description/application Symbol form/shape Read and understand Operator's Manual.
4 Physical Condition Y our judgment and physical dexterity may not be good: • if you are tired or sick, • if you are taking medication, • if you have taken alcohol or drugs. Operate unit only if you are physically and mentally well. Eye Protection W ear eye protection that meets ANSI Z87.
P o w e r P r u n e r TM o P e r a T o r ' s M a n u a l 5 DANGER All over head electrical conductors and communications wires can have electricity ow with high voltages. This unit is not insulated against electrical current. Never touch wires directly or indirectly when pruning, otherwise serious injury or death may result.
6 Keep A Solid Stance • Maintain footing and balance at all times. Do not stand on slippery , uneven or unstable surfaces. Do not work in odd positions or on ladders. Do not overreach. • Operate the Power Pruner TM only from the ground or out of an ap- proved bucket lift.
P o w e r P r u n e r TM o P e r a T o r ' s M a n u a l 7 e q u I p m e n t W ARNING Serious injury may result from the use of non approved guide bar and saw chain combinations. ECHO, INC. will not be responsible for the failure of cutting devices or accessories which have not been tested and approved by ECHO for use with this unit.
8 An Emission Control Label is located on the engine. (This is an EXAMPLE ONL Y , information on label varies by engine F AMIL Y). PRODUCT EMISSION DURABILITY The 300 hour emission durability complian.
P o w e r P r u n e r TM o P e r a T o r ' s M a n u a l 9 1 12 11 10 2 9 8 7 6 5 4 P/N X505002371 3 P/N X505002361.
10 1. POWER HEAD - Includes the Engine, Clutch, Fuel System, Ignition System and Starter . 2. THROTTLE TRIGGER - Spring loaded to return to idle when released. During acceleration press trigger gradu- ally for best operating technique. 3. SHOULDER HARNESS - An adjustable strap that suspends the unit from the operator .
P o w e r P r u n e r TM o P e r a T o r ' s M a n u a l 11 c o n t e n t s Due to packaging restriction the ECHO product you have purchased requires some assembly . After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or missing parts.
12 4. Align exible drive shaft coupler with engine socket and slide together until locating hole in shaft is visible through locating hole in engine housing. 5. Install locating screw (B) and tighten clamping bolts (A). B A A E F t h r o t t l e l I n k a G e a n d I G n I t I o n l e a d s 1.
P o w e r P r u n e r TM o P e r a T o r ' s M a n u a l 13 d c c I E F d W ARNING Saw Chain is sharp! Always wear gloves when handling assembly , otherwise serious personal injury may result. 1. Loosen the two (2) screws (C) and locator screw (D) on cutting attachment.
14 s a W c h a I n t e n s I o n a d J u s t m e n t W ARNING Always disconnect spark plug wire before servicing cutting attach- ment. W ear gloves when handling saw chain, otherwise serious personal injury may result. T o Adjust Saw Chain T ension 1.
P o w e r P r u n e r TM o P e r a T o r ' s M a n u a l 15 NOTICE: Use of unmixed, improperly mixed, or fuel older than 90 days, (stale fuel), may cause hard starting, poor performance, or severe engine damage and void the product warranty . Read and follow instructions in the Storage section of this manual.
16 Mixing Instructions 1. Fill an approved fuel container with half of the required amount of gasoline. 2. Add the proper amount of 2-stroke oil to gasoline. 3. Close container and shake to mix oil with gasoline. 4. Add remaining gasoline, close fuel container , and remix.
P o w e r P r u n e r TM o P e r a T o r ' s M a n u a l 17 Automatic Oiling System 1. W ipe debris from around oil ll cap. 2. Remove oil ll cap and ll reservoir with a quality , low viscosity guide bar and saw chain oil. NOTE The discharge volume of the automatic oiler is preset to deliver 3 to 4 cc/min.
18 C B d D A s t a r t I n G c o l d e n G I n e W ARNING The attachment will operate immediately when the engine starts and could result in loss of control and possible serious injury . Keep movable parts of the attachment off the ground and away from objects that could become entangled or thrown.
P o w e r P r u n e r TM o P e r a T o r ' s M a n u a l 19 s t a r t I n G W a r m e n G I n e The starting procedure is the same as Cold Start except DO NOT close the choke, and do not depress throttle trigger to wide open position. W ARNING The attachment should not move at idle, otherwise serious personal injury may result.
20 s t o p p I n G e n G I n e 1. Thr ottle . Release throttle trigger , and allow engine to return to idle before stopping engine. 2. Stop Switch. Move stop switch button (A) backward to STOP position. W ARNING If engine does not stop when stop switch is moved to STOP posi- tion, close choke - COLD ST AR T position - to stall engine.
P o w e r P r u n e r TM o P e r a T o r ' s M a n u a l 21 W ARNING Moving parts can amputate ngers or cause severe injuries. Keep hands, clothing and loose objects away from all openings.
22 a I r f I l t e r Level 1. T ools r equired: Cleaning brush 25 or 50 mm (1 or 2 in.) Parts r equired: Air Filter 1. Close choke (Cold Start Position [ ]). This prevents dirt from entering the carburetor throat when the air lter is removed. Brush accumulated dirt from air cleaner area.
P o w e r P r u n e r TM o P e r a T o r ' s M a n u a l 23 s p a r k p l u G Level 2. T ools r equired: 10x19mm (13/32x3/4in) T -wrench, Feeler gauge, Soft metal brush Parts Requir ed: Spark Plug NGK BPM-8Y IMPOR T ANT Use only NGK BPM-8Y spark plug (BPMR-8Y in Canada) oth- erwise severe engine damage may occur .
24 e X h a u s t s y s t e m Spark Arrestor Screen Level 2. T ools Requir ed: Cross Head Screwdriver , 4mm Hex W rench, Soft Metal Brush Parts Requir ed: Spark Arrestor Screen, Gasket 1. Remove mufer cover screw and mufer cover (A). 2. Place piston at T op Dead Center (TDC) to prevent carbon/dirt from entering cylinder .
P o w e r P r u n e r TM o P e r a T o r ' s M a n u a l 25 Exhaust Port Cleaning Level 2. T ools r equired: 4mm Hex W rench, 8mm W rench, W ood or plastic scraper Parts Requir ed: As needed: Heat Shield 1. Remove spark plug lead from spark plug, and remove mufer cover (1 screw).
26 c a r b u r e t o r a d J u s t m e n t Engine Break-In New engines must be operated a minimum duration of two tanks of fuel break-in before carburetor adjustments can be made. During the break- in period your engine performance will increase and exhaust emissions will stabilize.
P o w e r P r u n e r TM o P e r a T o r ' s M a n u a l 27 G u I d e b a r a n d s a W c h a I n r e p l a c e m e n t W ARNING Never try to replace or adjust guide bar and saw chain with engine running. Always disconnect spark plug wire before servicing guide bar and saw chain.
28 a B T o Adjust Saw Chain T ension 1. Move stop switch to STOP position. 2. Disconnect spark plug lead. 3. Loosen two gearcase cover nuts (A) until nger tight. 4. Hold the bar nose up, and turn the adjuster screw (B) clockwise un- til the chain ts snugly against the underside of the bar , as shown.
P o w e r P r u n e r TM o P e r a T o r ' s M a n u a l 29 IMPOR T ANT Chain and guide bar gauge size must be identical. Use Bar/Chain combinations shown in table above. PPT-265 Power Pruner B&C Combinations Bar P/N Chain P/N Chain Type Links Pitch Gauge Standard 12" Regular Bar P/N 12AOCD3744 M91VX44G 91 44 3/8" .
30 f I l I n G s a W c h a I n Level 2. T ools r equired: 4 mm (5/32 in.) Round File, Flat File, Depth Gauge IMPOR T ANT Dull or damaged cutters will result in poor cutting performance, increased vibration, and premature saw chain failure. W ARNING Always stop engine and disconnect spark plug wire before servic- ing guide bar and saw chain.
P o w e r P r u n e r TM o P e r a T o r ' s M a n u a l 31 t r o u b l e s h o o t I n G DANGER Fuel vapors are extremely ammable and may cause re and/or explosion. Never test for ignition spark by ground- ing spark plug near cylinder plug hole, otherwise serious personal injury may result.
32 2. Place the stop switch in the "OFF" position. 3. Remove accumulation of grease, oil, dirt and debris from exterior of unit. IMPOR T ANT Some tree sap and resins are corrosive. Thoroughly wash the guide bar and sprocket areas after each use, then coat metal parts with light oil.
P o w e r P r u n e r TM o P e r a T o r ' s M a n u a l 33 s p e c I f I c a t I o n s MODEL ---------------------------------------------------- PPT -265S Length (Standard) ------------------------------------------ 1.96 m (6 ft. 5 in.) Length (Extended) ----------------------------------------- 2.
34 n o t e s.
P o w e r P r u n e r TM o P e r a T o r ' s M a n u a l 35 n o t e s.
CONSUMER PRODUCT SUPPORT 1-800-673-1558 8:30 - 4:30 Mon - Fri C.S.T . ECHO, INCORPORA TED 400 O a k w O O d R O a d L a k e Z u R i c h , iL 60047 www .echo-usa.com a d d I t I o n a l o r r e p l a c e m e n t m a n u a l s Safety Manuals in English/Spanish or English/French are available, free of charge, from your ECHO dealer or at www .
Een belangrijk punt na aankoop van elk apparaat Echo PPT-265S (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Echo PPT-265S heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Echo PPT-265S vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Echo PPT-265S leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Echo PPT-265S krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Echo PPT-265S bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Echo PPT-265S kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Echo PPT-265S . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
