Gebruiksaanwijzing /service van het product IC43T-A2 (V1.0) van de fabrikant ECS
Ga naar pagina of 66
Preface Preface Copyright This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the author .
ii Preface Declaration of Conformity This device complies with part 15 of the FCC rules. Operation is subject to the following conditions: • This device may not cause harmful interference, and • T.
iii T T T T T ABLE OF CONTENTS ABLE OF CONTENTS ABLE OF CONTENTS ABLE OF CONTENTS ABLE OF CONTENTS Preface i Chapter 1 1 Introducing the Motherboard 1 Introduction......................................................................................1 Feature .
iv Integrated Peripherals.......................................................32 Power Management Setup.................................................33 PCI/PnP Setup...................................................................34 PC Health Status.
1 Introducing the Motherboard Chapter 1 Introducing the Motherboard Introduction Thank you for choosing the IC43T -A2 motherboard. This motherboard is a high performance, enhanced function motherboard.
2 Introducing the Motherboard Feature Processor This motherboard uses an LGA775 type of Intel ® Core ™ 2 Extreme/Core ™ 2 Quad/ Core ™ 2 Duo/Pentium ® Dual-Core/Celeron ® Dual-Core/Celeron ®.
3 Introducing the Motherboard • One PCI Express x16 slot for Graphics Interface • Three PCI Express x1 slots • T wo 32-bit PCI v2.3 compliant slots • Six 7-pin SA T A connectors Expansion Opti.
4 Introducing the Motherboard Motherboard Components.
5 Introducing the Motherboard T able of Motherboard Components This concludes Chapter 1. The next chapter explains how to install the motherboard. L AB E L C O MPO NE NT S LG A 7 7 5 s o ck et I n t e.
6 Introducing the Motherboard Memo.
7 Installing the Motherboard Chapter 2 Installing the Motherboard Safety Precautions • Follow these safety precautions when installing the motherboard • Wear a grounding strap attached to a ground.
8 Installing the Motherboard Checking Jumper Settings This section explains how to set jumpers for correct configuration of the motherboard. Setting Jumpers Use the motherboard jumpers to set system configuration options. Jumpers with more than one pin are numbered.
9 Installing the Motherboard Checking Jumper Settings The following illustration shows the location of the motherboard jumpers. Pin 1 is labeled. T o avoid the system instability after clearing CMOS, we recommend users to enter the main BIOS setting page to “Load Default Settings” and then “Save & Exit Setup”.
10 Installing the Motherboard Installing Hardware Installing the Processor Caution: When installing a CPU heatsink and cooling fan make sure that you DO NOT scratch the motherboard or any of the surface-mount resis- tors with the clip of the cooling fan.
11 Installing the Motherboard A. Read and follow the instructions shown on the sticker on the CPU cap. B. Unload the cap · Use thumb & forefinger to hold the lifting tab of the cap. · Lift the cap up and remove the cap completely from the socket.
12 Installing the Motherboard Installing Memory Modules This motherboard accommodates four memory modules. It can support four 240-pin DDR3 1066/800. The total memory capacity is 8 GB*. DDR3 SDRAM memory module table Y ou must install at least one module in any of the four slots.
13 Installing the Motherboard T able A: DDR3 (memory module) QVL (Qualified V endor List) The following DDR3 1066/800 memory modules have been tested and qualified for use with this motherboard.
14 Installing the Motherboard Users please be noted that DDR3 1333 MHz is validated to run at 1066 MHz only . Ty p e Si ze Ve n do r M o dule Na me A-dat a AD 313 33001GOU (AD 63I 1A08) Apac er AH U 0.
15 Installing the Motherboard The slots on this motherboard are designed to hold expansion cards and connect them to the system bus. Expansion slots are a means of adding or enhancing the motherboard’s features and capabilities.
16 Installing the Motherboard Follow these instructions to install an add-on card: 1 Remove a blanking plate from the system case corresponding to the slot you are going to use. 2 Install the edge connector of the add-on card into the expansion slot. Ensure that the edge connector is correctly seated in the slot.
17 Installing the Motherboard Connecting Optional Devices Refer to the following for information on connecting the motherboard optional devices F_AUDIO: Front Panel Audio header This header allows the user to install auxiliary front-oriented microphone and line- out ports for easier access.
18 Installing the Motherboard F_USB1~3: Front Panel USB headers The motherboard has four USB ports installed on the rear edge I/O port array . Additionally , some computer cases have USB ports at the front of the case. If you have this kind of case, use auxiliary USB connector to connect the front-mounted ports to the motherboard.
19 Installing the Motherboard Installing a SA T A Hard Drive About SA T A Connectors Y our motherboard features six SA T A connectors supporting a total of six drives. SA T A refers to Serial A T A (Advanced T echnology Attachment) is the standard inter- face for the IDE hard drives which are currently used in most PCs.
20 Installing the Motherboard Connecting I/O Devices The backplane of the motherboard has the following I/O ports: PS2 Mouse Use the upper PS/2 port to connect a PS/2 pointing device. PS2 Keyboard Use the lower PS/2 port to connect a PS/2 keyboard. Serial Port Use the COM port to connect serial devices such as mice or (COM) fax/modems.
21 Installing the Motherboard Connecting Case Components After you have installed the motherboard into a case, you can begin connecting the motherboard components. Refer to the following: The A TX_POWER 24-pin connector allows you to connect to A TX v2.
22 Installing the Motherboard SPK: Internal speaker header 4 Signal 3 GND 2 Key 1 VCC Pin Signal Name A TX12V : A TX 12V Power Connector A TX_POWER: A TX 24-pin Power Connector Pi n Signal Name 4 +12V 3 +12V 2 Ground 1 Ground SYS_F AN: System cooling F AN Power Connector Pin Signal Name Pin Signal Name 1 +3.
23 Installing the Motherboard Front Panel Header The front panel header (F_P ANEL) provides a standard set of switch and LED headers commonly found on A TX or Micr A TX cases. Refer to the table below for informa- tion: Supporting the reset function requires connecting pin 5 and 7 to a momentary- contact switch that is normally open.
24 Installing the Motherboard Memo.
25 Using BIOS Chapter 3 Using BIOS About the Setup Utility The computer uses the latest “American Megatrends Inc. ” BIOS with support for Windows Plug and Play . The CMOS chip on the motherboard contains the ROM setup instructions for configuring the motherboard BIOS.
26 Using BIOS Press the delete key to access the BIOS Setup Utility . CMOS Setup Utility -- Copyright (C) 1985-2008, American Megatrends, Inc. f f f f v02.
27 Using BIOS BIOS Navigation Keys The BIOS navigation keys are listed below: Enter Select K E Y FUNCTION Scrolls through the items on a menu + /- Modifies the selected field’s values F10 Saves the .
28 Using BIOS For the purpose of better product maintenance, the manufacture reserves the right to change the BIOS items presented in this manual. The BIOS setup screens shown in this chapter are for reference only and may differ fr om the actual BIOS.
29 Using BIOS Press <Esc> to return to the Standard CMOS Setup page. IDE BusMaster (Enabled) This item enables or disables the DMA under DOS mode. W e recommend you to leave this item at the default value. Press <Esc> to return to the main menu setting page.
30 Using BIOS Advanced Setup This page sets up more advanced information about your system. Handle this page with caution. Any changes can affect the operation of your computer .
31 Using BIOS Boot Up Numlock Status (On) This item defines if the keyboard Num Lock key is active when your system is started. APIC Mode (Enabled) This item allows you to enable or disable the APCI (Advanced Programmable Inter- rupt Controller) mode.
32 Using BIOS Integrated Peripherals This page sets up some parameters for peripheral devices connected to the system. Serial Port1 Address (3F8/IRQ4) Use this item to enable or disable the onboard COM1 serial port, and to assign a port address. Onboard LAN Function (Enabled) Use this item to enable or disable the onboard LAN function.
33 Using BIOS Power Management Setup This page sets up some parameters for system power management operation. CMOS Setup Utility - Copyright (C) 1985-2008, American Megatrends, Inc. Power Management Setup ACPI Suspend T ype (S3) Use this item to define how your system suspends.
34 Using BIOS PCI / PnP Setup This page sets up some parameters for devices installed on the PCI bus and those utilizing the system plug and play capability .
35 Using BIOS PC Health Status On motherboards support hardware monitoring, this item lets you monitor the parameters for critical voltages, temperatures and fan speeds. -=- System Hardware Monitor-=- Smart Fan Function Press Enter System T emperature : 33°C/91°F CPU FAN Speed : 2934 RPM CPU Core : 1.
36 Using BIOS CMOS Setup Utility - Copyright (C) 1985-2008, American Megatrends, Inc. Smart Fan Function Help Item F10: Save ESC: Exit +/-/: V alue Enter : Select F9: Load Default Settings F1:General .
37 Using BIOS System Component Characteristics These items display the monitoring of the overall inboard hardware health events, such as System & CPU temperature, CPU & DIMM voltage, CPU & system fan speed,...etc. • System T emperature • CPU F AN Speed • CPU Core • VDIMM Press <Esc> to return to the main menu setting page.
38 Using BIOS M.I.B. II (MB Intelligent BIOS II) This page enables you to set the clock speed and system bus for your system. The clock speed and system bus are determined by the kind of processor you have in- stalled in your system. CMOS Setup Utility - Copyright (C) 1985-2008, American Megatrends, Inc.
39 Using BIOS W arning: Please pay attention that doing overvoltage may result in damage to hardware. CPU V oltage (Disabled) This item enable or disable users to adjust the CPU voltage. NB V oltage (Disabled) This item enable or disable users to adjust the North Bridge voltage.
40 Using BIOS Load Non Disk 1. The default value of the item “Onboard LAN Boot ROM” is “ Disabled” accord- ingly since the item “Load Non Disk” is set to “Disabled” . 2. Y ou may highlight this option and press <Enter> to Enable it.
41 Using BIOS 4. Then the default value of the item “Onboard LAN Boot ROM” changed to “Enabled” . Press <Esc> to return to the main menu setting page.
42 Using BIOS Supervisor Password (Not Installed) This item indicates whether a supervisor password has been set. If the password has been installed, Installed displays. If not, Not Installed displays. Change Supervisor Password (Press Enter) Y ou can select this option and press <Enter> to access the sub menu.
43 Using BIOS Save & Exit Setup Highlight this item and press <Enter> to save the changes that you have made in the Setup Utility and exit the Setup Utility . When the Save and Exit dialog box appears, select [OK] to save and exit, or select [Cancel] to return to the main menu.
44 Using BIOS This concludes Chapter 3. Refer to the next chapter for information on the software supplied with the motherboard. Updating the BIOS Y ou can download and install updated BIOS for this motherboard from the manufacturer’s W eb site. New BIOS provides support for new peripherals, improve- ments in performance, or fixes for known bugs.
45 Using the Motherboard Software Chapter 4 Using the Motherboard Software If the opening screen does not appear; double-click the file “setup.exe” in the r oot directory .
46 Using the Motherboard Software Drivers T ab Setup Click the Setup button to run the software installation program. Select from the menu which software you want to install. Browse CD Exit The EXIT button closes the Auto Setup window . Utilities T ab Lists the software utilities that are available on the disk.
47 Using the Motherboard Software 2. Click Next. The following screen appears: 3. Check the box next to the items you want to install. The default options are recom- 4. Click Next run the Installation Wizard. An item installation screen appears: 5. Follow the instructions on the screen to install the items.
48 Using the Motherboard Software Manual Installation Insert the disk in the DVD-ROM/CD-ROM drive and locate the P A TH.DOC file in the root directory .
Setting Up eJIFFY 49 Introduction eJIFFY is a fast boot program under Linux. Instead of waiting Windows O.S to start execution, eJIFFY is ready to provide users the instant enjoyment on web browsing, photo review and online chat just within several seconds after boot up.
Setting Up eJIFFY 50 Installation and BIOS Setup DVD Activation Finish the DVD utility setup, and then set the BIOS to complete eJIFFY activation. 1. Insert ECS software utility DVD and enter below “Utilities” screen. Click eJIFFY feature item to install.
Setting Up eJIFFY 51 3. After setting up eJIFFY under Windows, you can switch eJIFFY display/keyboard language from English to your local language. The changes will be applied after rebooting. Note: The keyboard language selection list offers several more regional keyboard setups to switch with the default English typing.
Setting Up eJIFFY 52 4. Restart your computer after eJIFFY installation. Press <DEL> or click the BIOS Setup button on the post screen to enter the BIOS setup page after boot up. 5. And then enter the Advanced Setup page to enable the item ECS eJIFFY Func- tion .
Setting Up eJIFFY 53 Entering eJIFFY The post screen appears within several seconds after boot up and it has three buttons on it, Operating system, eJIFFY and BIOS Setup. If you click eJIFFY , the following screen will appear. And If you make no choice it will enter the normal OS automatically after ten seconds.
Setting Up eJIFFY 54 Feature Icons The following illustration shows the main feature icons that eJIFFY provides on the menu. ePix: Photo viewing. eW eb: Fir efo x for web br owsing/webmail and watching flash video . Shows eP al on-line connection status.
Setting Up eJIFFY 55 to open the language control panel. Keyboard Language Setup Usage F AQ Language Control P anel: Besides setting English as the default interface, eJIFFY offers multi-language displays and keyboard settings for language- switch. Open the language control panel to select a preferable language setting.
Setting Up eJIFFY 56 Click the language bar here. Move your mouse pointer on the text box and press Ctrl+Space. The language bar will then appear as fol- lows.
Setting Up eJIFFY 57 How to change display language? Open the Language Control Panel and click to show the display language list. Check your desired display language. Y our selected display language will be applied after rebooting. Note: Details about eJIFFY please r efer to eJIFFY in disk.
Setting Up eJIFFY 58 Memo.
59 Trouble Shooting Chapter 6 Trouble Shooting Start up problems during assembly After assembling the PC for the first time you may experience some start up problems. Before calling for technical support or returning for warranty , this chapter may help to address some of the common questions using some basic troubleshooting tips.
60 Trouble Shooting c) The PC suddenly shuts down while booting up. 1. The CPU may experience overheating so it will shutdown to protect itself. Ensure the CPU fan is working properly . 2. From the BIOS setting, try to disable the Smartfan function to let the fan run at default speed.
Power Bu on is p resse d but PC fails to s tart. Y es Check if Power Supply Unit (PSU) is working No No Any Beep sound ？ No CLR CMOS and check if CPU 12V power is connecte d art the PC st Re Problem.
62 Trouble Shooting Memo.
Een belangrijk punt na aankoop van elk apparaat ECS IC43T-A2 (V1.0) (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen ECS IC43T-A2 (V1.0) heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens ECS IC43T-A2 (V1.0) vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding ECS IC43T-A2 (V1.0) leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over ECS IC43T-A2 (V1.0) krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van ECS IC43T-A2 (V1.0) bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de ECS IC43T-A2 (V1.0) kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met ECS IC43T-A2 (V1.0) . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
