Gebruiksaanwijzing /service van het product 3530 van de fabrikant Edelbrock
Ga naar pagina of 33
©2005 Edelbrock Corporation Rev. 2/05 Brochure #63-0273 Catalog #3530 & #3531 ® INTRODUCTION Thank you for selecting the Edelbrock Pro-Flo Fuel Injection System.
2 Pro-Flo EFI Installation Instructions ©2005 Edelbrock Corporation Rev. 2/05 Brochure #63-0273 Catalog #3530 & #3531 COMPONENTS ❑ Electronic Control Unit/System ECU ❑ Calibration Module ❑ .
3 Pro-Flo EFI Installation Instructions ©2005 Edelbrock Corporation Rev. 2/05 Brochure #63-0273 Catalog #3530 & #3531 TOOLS AND EQUIPMENT Use the following checklist for items needed.
4 Pro-Flo EFI Installation Instructions ©2005 Edelbrock Corporation Rev. 2/05 Brochure #63-0273 Catalog #3530 & #3531 MANIFOLD & CARBURETOR HEIGHT VS . PRO-FLO HEIGHT 1. Remove air cleaner . 2 . Lay a straightedge (such as a yardstick) across the top of the carburetor from front to back.
5 Pro-Flo EFI Installation Instructions ©2005 Edelbrock Corporation Rev. 2/05 Brochure #63-0273 Catalog #3530 & #3531 AUTOMA TIC TRANSMISSION CHECK For best performance, economy , and emissions, the shift point must be checked before and after the manifold change.
6 Pro-Flo EFI Installation Instructions ©2005 Edelbrock Corporation Rev. 2/05 Brochure #63-0273 Catalog #3530 & #3531 FUEL SYSTEM Because your Edelbrock Pro-Flo system controls fuel delivery ver y differently than a carburetor , some conversions to your fuel system are necessary .
7 Pro-Flo EFI Installation Instructions ©2005 Edelbrock Corporation Rev. 2/05 Brochure #63-0273 Catalog #3530 & #3531 RUBBER RETURN LINE METHOD Drill a 5/16-inch hole in the sending unit plate adjacent to where the main line enters the tank. This will be the hole for your return line.
HARD RETURN LINE METHOD Drill a 5/16-inch hole in the sending unit plate adjacent to where the main line, enters the tank. This will be the hole for your return line. Insert a length of 5/16-inch hard line (available at most radia tor shops) into the hole and weld it to the sending unit plate.
9 Pro-Flo EFI Installation Instructions ©2005 Edelbrock Corporation Rev. 2/05 Brochure #63-0273 Catalog #3530 & #3531 NOTE: ALL WELDING AND SOLDERING OF THE FUEL SYSTEM MUST BE PERFORMED BY A PROFESSIONAL RADIA TOR OR FUEL SYSTEM REP AIR SHOP . FUEL SYSTEM INST ALLA TION 1.
10 Pro-Flo EFI Installation Instructions ©2005 Edelbrock Corporation Rev. 2/05 Brochure #63-0273 Catalog #3530 & #3531 INDUCTION SYSTEM The Edelbrock Pro-Flo system delivers fuel and air to the engine via the induction system consisting primarily of a manifold, 4-barrel air valve, fuel rails, and fuel injectors.
11 Pro-Flo EFI Installation Instructions ©2005 Edelbrock Corporation Rev. 2/05 Brochure #63-0273 Catalog #3530 & #3531 PRE-INST ALLA TION Before installing the induction system, take the following steps to ensure successful installation and performance: 1.
12 Pro-Flo EFI Installation Instructions ©2005 Edelbrock Corporation Rev. 2/05 Brochure #63-0273 Catalog #3530 & #3531 GASKET SURF ACE PREP ARA TION CAUTION: Replace all gaskets as recommended. W e recommend using an OEM style metal pan intake gasket ONL Y .
13 Pro-Flo EFI Installation Instructions ©2005 Edelbrock Corporation Rev. 2/05 Brochure #63-0273 Catalog #3530 & #3531 SENSORS The Edelbrock Pro-Flo system interprets overall engine operating conditions and fuel/spark requirements based on readings from sensors that measure specific engine conditions.
14 Pro-Flo EFI Installation Instructions ©2005 Edelbrock Corporation Rev. 2/05 Brochure #63-0273 Catalog #3530 & #3531 COOLANT TEMPERA TURE SENSOR The Coolant T empera ture Sensor is a thermistor device like the Manifold Air T empera ture sensor .
15 Pro-Flo EFI Installation Instructions ©2005 Edelbrock Corporation Rev. 2/05 Brochure #63-0273 Catalog #3530 & #3531 O 2 SENSOR INST ALLA TION The exhaust gas oxygen content is determined by the oxygen sensor . The sensor signals the ECU, which compensa tes when the air/fuel mixture is either rich or lean.
16 Pro-Flo EFI Installation Instructions ©2005 Edelbrock Corporation Rev. 2/05 Brochure #63-0273 Catalog #3530 & #3531 MAIN SYSTEM HARNESS If the ECU is the brain of the Edelbrock Pro-Flo system, the Main System Harness is the central nervous system.
17 Pro-Flo EFI Installation Instructions ©2005 Edelbrock Corporation Rev. 2/05 Brochure #63-0273 Catalog #3530 & #3531 Ignition Amplifier Tach Leed Fuses - Fuel Pump Relay O2 Sensor Fuel Pump To .
18 Pro-Flo EFI Installation Instructions ©2005 Edelbrock Corporation Rev. 2/05 Brochure #63-0273 Catalog #3530 & #3531 INST ALLA TION 1. Inspect the Main System Harness, making sure that all connectors and grounds are properly in place.
19 Pro-Flo EFI Installation Instructions ©2005 Edelbrock Corporation Rev. 2/05 Brochure #63-0273 Catalog #3530 & #3531 The Coolant T empera ture sensor attaches to the main harness. The Manifold Absolute Pressure sensor attaches to the main harness.
20 Pro-Flo EFI Installation Instructions ©2005 Edelbrock Corporation Rev. 2/05 Brochure #63-0273 Catalog #3530 & #3531 The IAC is attached to the main wiring harness. The ignition amplifier is attached to the main harness with the connector at left side of lo wer diagram.
21 Pro-Flo EFI Installation Instructions ©2005 Edelbrock Corporation Rev. 2/05 Brochure #63-0273 Catalog #3530 & #3531 ELECTRONIC CONTROL UNIT /SYSTEM ECU The Electronic Control Unit ( ECU ) must be mounted away from moisture, excessive heat, or vibration.
e s. 22 Pro-Flo EFI Installation Instructions ©2005 Edelbrock Corporation Rev. 2/05 Brochure #63-0273 Catalog #3530 & #3531 IGNITION SYSTEM IGNITION AMPLIFIER The Pro-Flo system uses the Edelbroc.
23 Pro-Flo EFI Installation Instructions ©2005 Edelbrock Corporation Rev. 2/05 Brochure #63-0273 Catalog #3530 & #3531 3. Install the supplied .030” thrust washer and the OEM gear onto the new distributor by sliding them onto the shaft.
24 Pro-Flo EFI Installation Instructions ©2005 Edelbrock Corporation Rev. 2/05 Brochure #63-0273 Catalog #3530 & #3531 OTHER APPLICA TIONS The Pro-Flo system has been designed and calibrated using a 304 AMC V8 engine with an Edelbrock Performer -Plus camshaft and tubular headers as a baseline.
25 Pro-Flo EFI Installation Instructions ©2005 Edelbrock Corporation Rev. 2/05 Brochure #63-0273 Catalog #3530 & #3531 Priming The Fuel Pump Before the engine is started, the fuel pump must be primed to pressurize the system and purge the fuel line of all air .
26 Pro-Flo EFI Installation Instructions ©2005 Edelbrock Corporation Rev. 2/05 Brochure #63-0273 Catalog #3530 & #3531 3. THIS STEP REQUIRES TWO PEOPLE OR USE OF A REMOTE ST ARTER SWITCH. While one person rotates the engine by slowly bumping the starter , the other holds his finger over the Number One plug hole until compression is felt.
27 Pro-Flo EFI Installation Instructions ©2005 Edelbrock Corporation Rev. 2/05 Brochure #63-0273 Catalog #3530 & #3531 Idle Calibration Procedure • Prior to idle calibration, you need to have completed the "System Start-Up" procedure • Warm up engine to at least 175°F .
28 Pro-Flo EFI Installation Instructions ©2005 Edelbrock Corporation Rev. 2/05 Brochure #63-0273 Catalog #3530 & #3531 ELECTRONIC ENGINE MANAGEMENT The Edelbrock Pro-Flo system uses the Speed-Den.
29 Pro-Flo EFI Installation Instructions ©2005 Edelbrock Corporation Rev. 2/05 Brochure #63-0273 Catalog #3530 & #3531 PRO-FLO QUICK TUNING GUIDE These are basic instructions to help in understanding the tuning of your Pro-Flo fuel injection system.
30 Pro-Flo EFI Installation Instructions ©2005 Edelbrock Corporation Rev. 2/05 Brochure #63-0273 Catalog #3530 & #3531 FUEL @ ____ 2000: ± 0% EXIT = scroll ENTER POWER ON ENTER/EXIT UP DOW N UP .
31 Pro-Flo EFI Installation Instructions ©2005 Edelbrock Corporation Rev. 2/05 Brochure #63-0273 Catalog #3530 & #3531 Edelbrock Pro-Flo Fuel Injection System #3530/3531 P AR T NUMBERS Many of the components of the Pro-Flo system are available separa tely .
32 Pro-Flo EFI Installation Instructions ©2005 Edelbrock Corporation Rev. 2/05 Brochure #63-0273 Catalog #3530 & #3531 Check Qty . Description 1 Manifold Assembly ( as seen belo w) 1 Installa tion Instructions 1 EFI Owner’ s Manual 1 Basic ECU 1 Fuel Filter 1 Manifold Air T emperature Sensor and Grommet 1 Fuel Pump 1 Cal.
33 Pro-Flo EFI Installation Instructions ©2005 Edelbrock Corporation Rev. 2/05 Brochure #63-0273 Catalog #3530 & #3531 SERVICE In the event that your Edelbrock Pro-Flo System should need ser vicing, return the unit (freight pre- paid) to the Edelbrock Service and Repair facility a t 2700 California Street, T orrance, CA 90503.
Een belangrijk punt na aankoop van elk apparaat Edelbrock 3530 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Edelbrock 3530 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Edelbrock 3530 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Edelbrock 3530 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Edelbrock 3530 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Edelbrock 3530 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Edelbrock 3530 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Edelbrock 3530 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
