Gebruiksaanwijzing /service van het product 70207 van de fabrikant Edelbrock
Ga naar pagina of 28
2001 Edelbrock Corporation Brochure No. 63-0020 © Rev . 10/01 Thank Y ou…. …for purchasing an Edelbrock Nitrous Oxide Injection System. Nitrous Oxide injection is one of the most exciting performance enhancements, for the dollar invested, on the market today .
2001 Edelbrock Corporation Brochure No. 63-0020 © Rev . 10/01 L T1 CAMARO / FIREBIRD / IMP ALA PERFORMER EFI SERIES NITROUS SYSTEM T able of Content s Page # a. Before Y ou Install Y our Edelbrock Nitrous System . . . . . . . . . . . . . . . . . . . .
2001 Edelbrock Corporation Brochure No. 63-0020 © Rev . 10/01 Page 2 of 27 L T1 CAMARO / FIREBIRD / IMP ALA PERFORMER EFI SERIES NITROUS SYSTEM T able of Content s Page # 3.0 Electrical System Inst allation (Continuation) 3.8 Fuel Booster Pump . . . .
2001 Edelbrock Corporation Brochure No. 63-0020 © Rev . 10/01 Page 3 of 27 Caution!! Before Y ou Inst all Y our Edelbrock Nitrous System… Please read this Inst allation manual fully before inst alling this system.
2001 Edelbrock Corporation Brochure No. 63-0020 © Rev . 10/01 Page 4 of 27 WHA T IS NITROUS OXIDE? Nitrous Oxide is a cryogenic gas composed of nitrogen and oxygen molecules. It is stored as a “gas over a liquid” which means that both liquid and gaseous nitrous oxide is delivered into your engine.
2001 Edelbrock Corporation Brochure No. 63-0020 © Rev . 10/01 Page 5 of 27 1.0 Introduction to your Edelbrock L T1 Performer EFI Nitrous System ….about this manual! Within the pages of this manual is information, safety tip s and operation instructions for your new Edelbrock Nitrous System.
2001 Edelbrock Corporation Brochure No. 63-0020 © Rev . 10/01 Page 6 of 27 1.2 Jet Map Information Edelbrock engineering has conducted dyno testing with the Edelbrock L T1 Performer EFI system to ensure the horsepower increase the nitrous system is as intended.
2001 Edelbrock Corporation Brochure No. 63-0020 © Rev . 10/01 Page 7 of 27 QTY . DESCRIPTION Nozzle and Nozzle Hardware 1 Nitrous fan spray nozzle 1 Nitrous fan spray nozzle bulkhead body bolt 1 Nitr.
2001 Edelbrock Corporation Brochure No. 63-0020 © Rev . 10/01 Page 8 of 27 2.0 Performer System Inst allations 2.1 Nitrous Bottle Mounting The nitrous oxide storage cylinder is typically called a “nitrous bottle”. It is an aluminum cylinder , designed and manufactured to withstand very high pressures.
2001 Edelbrock Corporation Brochure No. 63-0020 © Rev . 10/01 Page 9 of 27 2.2 Bottle Mounting Instructions Accurate calibration of your nitrous system depends on the bottle remaining at a stable temperature. Choosing the proper location and orientation for your bottle can greatly af fect the overall operation of the nitrous system.
2001 Edelbrock Corporation Brochure No. 63-0020 © Rev . 10/01 Page 10 of 27 2.4 Nitrous Bottle Inst allation After you have determined the location and orient ation of the nitrous bottle, use the following procedure to install the bottle: 2.4.1 Street Car Inst allations 1.
2001 Edelbrock Corporation Brochure No. 63-0020 © Rev . 10/01 Page 11 of 27 2.5 Nitrous Feed Line Mounting 1. Determine the route your main nitrous feed line will follow . Ensure the p ath does not route the nitrous feed line too close to the exhaust system, suspension, electrical lines/components or tires.
2001 Edelbrock Corporation Brochure No. 63-0020 © Rev . 10/01 Page 12 of 27 2.6.2 Nitrous Solenoids Mounting (Continued) 9. V erify the desired mounting location for the solenoid assembly . 10. After mounting location is determined, tighten all fittings.
2001 Edelbrock Corporation Brochure No. 63-0020 © Rev . 10/01 Page 13 of 27 2.8 EFI V acuum “T ee” Inst allation 1. Install the .042 jet into the EFI V acuum “T ee” and tighten the fitting securely . 2. Remove vacuum line from the vehicle’s fuel pressure regulator .
2001 Edelbrock Corporation Brochure No. 63-0020 © Rev . 10/01 Page 14 of 27 2.10 Fuel Pump Installation 2.10.1 (Camaro, Firebird) Warning: Before performing any of these steps, relieve the pressure in the fuel system. 1. Locate the fuel filter on the under-carriage of the car .
2001 Edelbrock Corporation Brochure No. 63-0020 © Rev . 10/01 Page 15 of 27 3.1 Nitrous Electrical Component s Bill of Materials (BOM) 3.2 Nomenclature Descriptions: A TO… the fuse configuration is A TO. When replacing this fuse, ask for an A TO fuse.
2001 Edelbrock Corporation Brochure No. 63-0020 © Rev . 10/01 Page 16 of 27 3.3 Nitrous Electrical System Wiring Diagram.
2001 Edelbrock Corporation Brochure No. 63-0020 © Rev . 10/01 Page 17 of 27 3.4 Nitrous Electrical System Installation Procedures Determine the location of the Relay and Fuse Holder wire harness. Most common installations locate these components inside the driver’s compartment and close to the fuse panel under the dash.
2001 Edelbrock Corporation Brochure No. 63-0020 © Rev . 10/01 Page 18 of 27 3.6 Arming Switch and Inst allation The arming switch is a red, lighted switch that is a “MASTER” arming switch for your nitrous system.
2001 Edelbrock Corporation Brochure No. 63-0020 © Rev . 10/01 Page 19 of 27 3.7 Microswitch Inst allation and Wiring (Continued) The bolts used to att ach the microswitch have extra length to allow for spacing the microswitch away from the bracket to offer a level of adjust ability of the microswitch.
2001 Edelbrock Corporation Brochure No. 63-0020 © Rev . 10/01 Page 20 of 27 3.8 Fuel Booster Pump Electrical Component s Bill of Materials (BOM) Item # Quantity Description 1 1 ea. 30 amp relay 2 1 ea. Wire harness with integral relay/fuse holder 3 1 ea.
2001 Edelbrock Corporation Brochure No. 63-0020 © Rev . 10/01 Page 21 of 27 3.9 Fuel Booster Pump Electrical System Inst allation Procedures Determine the location of the Fuel Booster Relay and Fuse Holder wire harness.
2001 Edelbrock Corporation Brochure No. 63-0020 © Rev . 10/01 Page 22 of 27 3.1 1 Knock Sensor By-Pass Relay Component s Bill of Materials (BOM) Item # Quantity Description 1 1 ea. 30 amp relay 2 1 ea. Knock Sensor Relay Harness 3 2 ea. 16/18 S plice Connector 4 2 ea.
2001 Edelbrock Corporation Brochure No. 63-0020 © Rev . 10/01 Page 23 of 27 3.12 Knock Sensor By-Pass Relay Inst allation (Continued) The wire harness attached to the relay includes 4 feet of color-coded wires to make the electrical system installation for your Edelbrock Nitrous System as easy as possible.
2001 Edelbrock Corporation Brochure No. 63-0020 © Rev . 10/01 Page 24 of 27 4.0 Before Y ou Run Y our V ehicle Using Y our Edelbrock Nitrous System Y ou have just completed the installation of your Edelbrock Nitrous System.
2001 Edelbrock Corporation Brochure No. 63-0020 © Rev . 10/01 Page 25 of 27 5.0 T roubleshooting and Routine Maintenance How to use our T roubleshooting Flowchart: The troubleshooting of a nitrous system is basic and straightforward. The symptom chart is divided by symptom, cause and action required.
2001 Edelbrock Corporation Brochure No. 63-0020 © Rev . 10/01 Page 26 of 27 6. Inadequate nitrous supply . a. Weigh bottle. 1. Bottle should be 10 lbs. above empty bottle weight listed on bottle label when full. b. Check bottle pressure. 1. Maintain 900-950 p si for optimum system performance.
2001 Edelbrock Corporation Brochure No. 63-0020 © Rev . 10/01 Page 27 of 27 6.0 Solenoid Inspection and Maintenance. 1. Close valve on nitrous bottle. 2. Make sure all nitrous supply lines are free of pressure before removal of any system solenoid. a.
Een belangrijk punt na aankoop van elk apparaat Edelbrock 70207 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Edelbrock 70207 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Edelbrock 70207 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Edelbrock 70207 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Edelbrock 70207 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Edelbrock 70207 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Edelbrock 70207 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Edelbrock 70207 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.