Gebruiksaanwijzing /service van het product Performer Series 1403 van de fabrikant Edelbrock
Ga naar pagina of 39
1 Edelbrock Performer Series Carburetor Owner’s Manual 3/00 INTRODUCTION Your Edelbrock Performer Series carburetor was calibrated using Edelbrock Performer, Performer RPM, and Torker II Power Packages. The carburetor metering was developed on Edelbrock engine dynamometers, chassis rolls, and a variety of development vehicles.
2 Edelbrock Performer Series Carburetor Owner’s Manual 8/94 SECTION 1: THEOR Y OF OPERA TION BASIC ENGINE REQUIREMENTS The spark-ignition 4-cycle engine burns a mixture of AIR and FUEL. The air is controlled by the driver’s operation of the throttle.
3 Edelbrock Performer Series Carburetor Owner’s Manual 8/94 METERING SYSTEMS The Edelbrock carburetor has three (3) basic systems that meter fuel to the engine: The Idle System, Primary Main System, and Secondary Main System. By understanding the operation of each you will be better prepared to calibrate your carburetor.
4 Edelbrock Performer Series Carburetor Owner’s Manual 8/94 Fuel is drawn through the Idle System (Figure 2) by the intake manifold vacuum that is communicated at the Idle Screw Port (8) and Transfer Slot (7). Fuel in the bowl passes through the Primary Main Jet and Metering Rod Restriction (1) and into the Primary Well (2).
5 Edelbrock Performer Series Carburetor Owner’s Manual 8/94 The fuel flow rate in the Main System is proportional to the air flow rate; as air flow increases - from either an increase in throttle opening or an increase in engine speed at the same throttle opening - the fuel flow also increases by nearly the same degree.
6 Edelbrock Performer Series Carburetor Owner’s Manual 8/94 TRANSIENT CONTROL SYSTEMS In addition to the three (3) basic Metering Systems, there are two (2) Transient Control Systems; The Secondary Auxiliary System and The Pump System.
7 Edelbrock Performer Series Carburetor Owner’s Manual 8/94 “bog” or “flat spot” on secondary opening, it is necessary to add fuel by an auxiliary means during the time the secondary is in the transient phase. This is accomplished by placing a small Discharge Nozzle (2) at a point just under the Air Valve (1).
8 Edelbrock Performer Series Carburetor Owner’s Manual 8/94 EXTERNAL DEVICES The function of your Edelbrock Performer Series carburetor is also dependent on several external devices; the fuel pump and air cleaner. Fuel Pumps and Pressure Avoid extremes in fuel pressure.
9 Edelbrock Performer Series Carburetor Owner’s Manual 8/94 Air Cleaners Your Edelbrock carburetor was originally calibrated with a low restriction open element air cleaner configuration; a 14”x3” Edelbrock Signature Series unit.
10 Edelbrock Performer Series Carburetor Owner’s Manual 9/01 To help you calibrate your carburetor, a CALIBRATION REFERENCE CHART has been designed for each model of the Edelbrock Performer Series carburetor. These charts (pages 18—31) each consist of two sections: A Calibration Table and a Rod/Jet Reference Chart.
11 Edelbrock Performer Series Carburetor Owner’s Manual 9/01 Changing Components Metering Rod and Step-Up Spring changes can typically be made in less than five minutes and without removing the carburetor. First, loosen the Step-Up Piston Cover Screws (See pg.
12 Edelbrock Performer Series Carburetor Owner’s Manual 8/94 Long Duration Camshaft If the engine has a fairly radical camshaft it may require an excessive amount of throttle opening for idle and/or have low idle vacuum levels. Either condition can lead to poor levels of adjustability and erratic idles.
13 Edelbrock Performer Series Carburetor Owner’s Manual 8/94 Case 2: Slower than base calibration Go to 1 stage lean Primaries and 1 lean Secondaries and perform acceleration test #3. • If test #3 is the same as base calibration, go back to the base calibration.
14 Edelbrock Performer Series Carburetor Owner’s Manual 1/01 CALIBRATING THE POWER MODE STAGING The Step-Up function, which moves the Metering Rod to the Power Mode, is controlled by the Step-Up Spring. The base calibration has a spring which “stages” rich at 5” Hg.
15 Edelbrock Performer Series Carburetor Owner’s Manual Rev 9/01 Float Drop (15/16" to 1") Figure 9 Float Level (7/16") Figure 8 Fast idle linkage Figure 11 Choke piston linkage Figure 10 BEND HERE TAB C (.100") C (3/64") A A B D .
16 Edelbrock Performer Series Carburetor Owner’s Manual Rev 1/01 * = Carburetor is certified to meet U.S. Coast Guard Requirements The length of time during which the choke will stay closed is determined by the position of the choke cap. As the choke cap is turned clockwise the choke will stay closed longer.
17 Edelbrock Performer Series Carburetor Owner’s Manual 9/01 altitude, however, and is to be driven at high altitude temporarily, it is not necessary to repeat the complete calibration procedure. Instead, use the rule of: “2% leaner per 1500 feet” and the Calibration Reference Chart for your model carburetor.
18 Edelbrock Performer Series Carburetor Owner’s Manual 12/01 Step 1 Select the combination of Cruise Mode and Power Mode fuel-metering stages desired for your calibration.
19 Edelbrock Performer Series Carburetor Owner’s Manual 12/01 3 Stages 2 Stages 1 Stage SECONDARY 1 Stage 2 Stages 3 Stages Lean (12%) Lean (8%) Lean (4%) Stock Calibration Rich (4%) Rich (8%) Rich (12%) JET #1423 JET #1424 JET #1425 JET #1426 JET #1427 JET #1429 JET #1430 (.
20 Edelbrock Performer Series Carburetor Owner’s Manual 8/94 Step 1 Select the combination of Cruise Mode and Power Mode fuel-metering stages desired for your calibration.
21 Edelbrock Performer Series Carburetor Owner’s Manual 8/94 Model #1405 Rod/Jet Reference Chart REF # MAIN JET METERING ROD CHANGE FROM BASE 1 1428 (.100) 1451 (070 x 047)* none - stock calibration *Some Have ID #695 2 1428 (.100) 1450 (070 x 042) Rod 3 1428 (.
22 Edelbrock Performer Series Carburetor Owner’s Manual 1/01 Step 1 Select the combination of Cruise Mode and Power Mode fuel-metering stages desired for your calibration.
23 Edelbrock Performer Series Carburetor Owner’s Manual 8/94 Model #1406 Rod/Jet Reference Chart REF # MAIN JET METERING ROD CHANGE FROM BASE 1 1427 (.098) 1459 (075 x 047) none - stock calibration 2 1426 (.095) 1449 (070 x 037) Rod & Jet 3 1427 (.
24 Edelbrock Performer Series Carburetor Owner’s Manual 8/94 Step 1 Select the combination of Cruise Mode and Power Mode fuel-metering stages desired for your calibration.
25 Edelbrock Performer Series Carburetor Owner’s Manual 8/94 Model #1407 & #1410 Rod/Jet Reference Chart REF # MAIN JET METERING ROD CHANGE FROM BASE 1 1433 (.113) 1453 (071 x 047) none - stock calibration 2 1433 (.113) 1450 (070 x 042) Rod 3 1433 (.
26 Edelbrock Performer Series Carburetor Owner’s Manual 8/94 Step 1 Select the combination of Cruise Mode and Power Mode fuel-metering stages desired for your calibration.
27 Edelbrock Performer Series Carburetor Owner’s Manual 8/94 Model #1409 Rod/Jet Reference Chart REF # MAIN JET METERING ROD CHANGE FROM BASE 1 1427 (.098) 1447 (068 x 047) none - stock calibration 2 1427 (.098) 1446 (068 x 042) Rod 3 1429 (.101) 1456 (073 x 047) Rod & Jet 4 1427 (.
28 Edelbrock Performer Series Carburetor Owner’s Manual 8/94 Step 1 Select the combination of Cruise Mode and Power Mode fuel-metering stages desired for your calibration.
29 Edelbrock Performer Series Carburetor Owner’s Manual 8/94 Model #1411 Rod/Jet Reference Chart REF # MAIN JET METERING ROD CHANGE FROM BASE 1 1432 (.110) 1459 (075 x 047) none - stock calibration 2 1432 (.110) 1419 (075 x 042) Rod 3 1432 (.110) 1458 (075 x 037) Rod 4 1431 (.
30 Edelbrock Performer Series Carburetor Owner’s Manual 10/00 Step 1 Select the combination of Cruise Mode and Power Mode fuel-metering stages desired for your calibration.
31 Edelbrock Performer Series Carburetor Owner’s Manual 10/00 Model #1412 & #1413 Rod/Jet Reference Chart REF # MAIN JET METERING ROD CHANGE FROM BASE 1 1433 (.113) 1453 (071 x 047) none - stock calibration 2 1433 (.113) 1450 (070 x 042) Rod 3 1433 (.
32 Edelbrock Performer Series Carburetor Owner’s Manual 8/94 Item Description 1. Step-up piston cover screws (2) 2. Step-up piston cover plates (2) 3. Step-up pistons (2) 4. Step-up (metering) rods (2) 5. Step-up piston springs (2) 6. Step-up rod retainer springs (2) 7.
33 Edelbrock Performer Series Carburetor Owner’s Manual 8/94 27. Needle & seat assemblies (2) 28. Airhorn gasket 29. Pump plunger assembly 30. Pump plunger spring 31. Primary cluster screws (4) 32. Primary venturi boosters (2) 33. Venturi booster gaskets (2) 34.
Check for air leaks. Make sure carburetor and manifold gaskets seal properly. All outlets must be plugged or connected. Check ignition system. Replace parts as necessary. Adjust timing to proper specifications. Check choke adjustment. See page 14. Change carburetor fuel filter and/or in-line fuel filter.
35 Edelbrock Performer Series Carburetor Owner’s Manual 8/94 Symptoms Carburetor doesn’t adjust Carburetor floods Fuel leaks at shaft Internal fuel leak Misses or surges Stumbles or loads up Engin.
36 Edelbrock Performer Series Carburetor Owner’s Manual 3/00 ® T roubleshooting Information Dirt/metal shavings between the needle and seat or a “sticking float”: T o correct either of these problems, lightly ta p the carburetor fuel inlet area with the handle of a screwdriver .
37 Edelbrock Performer Series Carburetor Owner’s Manual 9/01 W ARRANTY EDELBROCK warrants its Performer Series Carburetors to be free from defects in material or workmanship.
38 Edelbrock Performer Series Carburetor Owner’s Manual 8/94 Notes: 1403-1413 Perf Series Carburetor Owner's Manual.qxd 3/31/2006 12:03 PM Page 38.
39 Edelbrock Performer Series Carburetor Owner’s Manual 8/94 Edelbrock Carburetor Data Log In order to get the most from your Edelbrock carburetor purchase, please complete and mail the enclosed warranty card. Also, you may want to record your calibration settings in the table below and keep it with your vehicle records.
Een belangrijk punt na aankoop van elk apparaat Edelbrock Performer Series 1403 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Edelbrock Performer Series 1403 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Edelbrock Performer Series 1403 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Edelbrock Performer Series 1403 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Edelbrock Performer Series 1403 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Edelbrock Performer Series 1403 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Edelbrock Performer Series 1403 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Edelbrock Performer Series 1403 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
