Gebruiksaanwijzing /service van het product EIP-X350 van de fabrikant Eiki
Ga naar pagina of 35
MUL TIMEDIA PROJECTOR MODEL EIP-X350 O WNER’S MANUA L.
EN-1 Federal Communication Commission Notice Note : This equipment ha s been tested a nd found to comply with the limits f or a Cla ss B digital device, pursuant to part 15 of the FCC Rules. These li mits are designed to provide rea sonable protection against harmful interference in a residential installation.
EN-2 Safety Instructions Read all of these instructions before you operate your projector and save for future reference. CAUTION : T O REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE EXCEPT LAMP REPLACEMENT.
EN-3 1 . Check that the operating voltage of your unit is identical with the voltage of your local power supply. 2. Should any liquid or solid object fall into the cabinet, unplug the unit and have it checked by the qualified personnel before operating it further.
EN-4 1 6 . The product should be situated away from heat sources such a s radiators, hea t registers, stoves, or other products (including a mplifiers) that produce heat. 17 . Do not overload wall outlets, extension cords, or integral convenience recepta cles a s this ca n result in a risk of fire or electric shock.
EN-5 CONTENTS Introduction ............................................................................................................... 6 Projector Features ...........................................................................................
EN-6 Introduction Projector Fea tur es The projector integrates high-performance optical engine projection and a user-friendly design to deliver high reli ability and ea se of use.
EN-7 Package Contents When you unpa ck the projector , ma ke sure you have all these components: Projector with Lens Ca p AC Power Cord V GA Cable (D-SUB to D-SUB) Composite Video Cable Owner’s Manu.
EN-8 Projector Over view Front View 1 Lens ca p 2 Lens ca p stra p 3 Elevator foot 4 Front IR remote control sensor 5 Elevator button 3 4 6 8 7 9 10 11 12 12 5 1 2 6 Projection lens 7 Focus ring 8 Til.
EN-9 1 2 3 4 5 7 5 6 Rear View 1 Rear IR remote control sensor 2 T erminals 3 Main power switch 4 AC power socket 5 Tilt-adjustment foot 6 V entilation holes 7 Kensington lock 2 1 2 2 This projector ca n be used with a ceiling mount for support. The ceiling mount is not included in the package.
EN-10 Using the Product Control Panel LED 1 T emp. (T emperature LED indicator) Refer to “LED Indicator Messages”. (p.30) 2 Lamp. (La mp LED indicator) Refer to “LED Indicator Messages”. (p.30) 3 (Power LED indicator) Refer to “LED Indicator Messages”.
EN-11 T er minals 1 Audio out Connects to a speaker or other audio input equipment. 2 USB This connector is for page up & down mouse control function and firmware update. 3 RS-232 When operating the projector via a computer, connect this to the controlling computer’s RS-232C port.
EN-12 Remote Control 1 Power Turns the projector on or off. (p.17) 2 Four directional buttons Use four directional buttons to select items or make adjustments to your selection. (p.21) 3 MENU Opens the on-screen menu or a cts on the selected menu item.
EN-13 Installing the Batteries 1. Open the battery cover in the direction shown. 2. Install batteries a s indicated by the diagra m inside the compartment. 3. Close the battery cover into position. Keep the batteries out of the rea ch of children. There is a danger of death by accidentally swallowing the battery.
EN-14 Ground Notes on AC Power Cord AC Power Cord must meet requirement of country where you use a projector. Confirm a n AC plug type with gra phics below and proper AC Power Cord must be used. If supplied AC Power Cord does not match your AC outlet, contact your sales dealer .
EN-15 Remote Control Operation Point the remote control at the infrared remote sensor and press a button. Operating the projector from the front Operating the projector from the rear Do not point the laser pointer directly to the people's eyes (especially small children).
EN-16 Installation Connecting the Projector 1 USB Cable 6 Composite Video Cable 2 RS-232 Cable 7 V GA (D-Sub) to HDTV (RCA) Cable 3 D VI Cable 8 YPbPr Cable 4 V GA Cable (D-Sub to D-Sub) 9 Audio Cable.
EN-17 Powering On/Off the Projector Powering on the projector: 1. Remove the projector lens ca p. 2. Complete the AC power cord and peri pheral signal cable(s) connections. 3 . Turn on the main power switch. 4. The power LED indicator blinks blue in standby mode.
EN-18 Adjusting the Projector Adjusting the Projector Height The projector is equipped with an elevator foot and tilt-adjustment feet to adjust the image height. 1. T o raise or lower the i mage, press the elevator button and raise or lower the front of the projector .
EN-19 Adjusting the Projector Zoom and Focus 1. Focus the image by rotating the focus ring. A still image is recommended for focusing. 2. Adjust the image by rotating the zoom ring. Rotate to the right to enlarge the image. Rotate to the left to reduce the image.
EN-20 Position the projector in a horizontal position; other positions ca n cause heat build-up a nd da mage to the projector . Ma ke sure the heat ventilation holes are not blocked. Do not use the projector in a smoky environment. Smoke residue may cause buildup on critical parts.
EN-21 Menu Operation The projector ha s multilingual on-screen display menus that allow you to make i mage adjustments and change a variety of settings. How to operate 1. Press MENU to display the on-screen menu. 2. Press S / T to select any feature in the main menu, then press X to move into that menu.
EN-22 Setup Menu Keystone Adjusts image distortion caused by tilting projection. Reset keystone Resets the keystone correction to zero (no correction). V olume Adjusts the loudness of the projector’s audio. Mute T emporarily turns of f the projector’s audio.
EN-23 Picture Menu Cha nging these settings affects only the a ctive source. Some picture adjustments are available only when certain input ports are in use. U navaila ble adjustments are shown in gray in the on-screen menu. Color settings Adjusts the image and colors.
EN-24 Frequency Adjusts the timing of the projector relative to the computer. T racking Adjusts the pha se of the projector relative to the computer . V ertical offset Adjusts the image up or down within the projection area. Horizontal offset Adjusts the image left or right within the projection area.
EN-25 Source Menu VG A Shows the source connected to the V GA-in port. Composite video Shows the source connected to the composite-video port. S-video Shows the source connected to the S-video port. Component Shows the source connected to the component video port.
EN-26 T urn off the projector a nd remove the AC power cord from the power outlet before beginning maintena nce work. Ma ke sure the lens is cool before cle aning. Do not use detergents or chemicals other tha n those noted above. Do not use benzene or thinners.
EN-27 Replacing the Lamp As the projector operates over ti me, the brightness of the projector la mp gradually decrea ses and the la mp becomes more susceptible to brea kage. W e recommend repla cing the la mp if a warning message is displayed. The lamp becomes high temperature after turning off the projector with the power button.
EN-28 Dispose of the used lamp according to local regulations. Ensure that screws are tightened properly. Screws not tightened fully may result in injury or accidents. Since the la mp is ma de of glass, do not drop the unit a nd do not scratch the glass.
EN-29 Specifications Display T ype Single 0.7" DLP pa nel Resolution (Pixels) XGA (1024 × 768) Lens Manual Zoom (1.2x) F=2.3~2.75 f=23.6~28.25mm Throw distance 1.
EN-30 Appendix LED Indicator Messages The projector is operating normally. Standby mode During shutdown cool-down. During fla sh update. La mp failure.
EN-31 Compatibility Modes Computer: Compatibility Resolution H-Sync [KHz] V -Sync [Hz] V GA 640x480 31.469 59.940 640x480 37.861 72.809 640x480 37.500 75.000 640x480 43.269 85.008 SV GA 800x600 35.156 56.250 800x600 37.879 60.317 800x600 48.077 72.188 800x600 46.
EN-32 T r ou b leshooting Refer to the statement that most closely matches the nature of the problem before sending the projector for repairs. If the problem persists, conta ct your local reseller or service center. Plea se refer to “LED Indicator Messages” (p.
EN-33 If the image is flickering or unstable for a computer connection: If the remote control does not operate: - Press the Resync button. - Press MENU , go to Picture > V GA settings , a nd adjust Frequency or T racking . - Be sure nothing is blocking the remote control rece iver on the front or ba ck of the projector.
U.S.A. EIKI International, Inc. 30251 Esperanza Rancho Santa Margarita CA 92688-2132 U.S.A. T el : 800-242-3454 (949)-457-0200 Fax : 800-457-3454 (949)-457-7878 E-Mail : usa@eiki.com Deutschland & Österreich EIKI Deutschla nd GmbH Am Frauwald 12 65510 Idstein Deutschland T el : 06126-9371-0 Fax : 06126-9371-14 E-Mail : info@eiki.
Een belangrijk punt na aankoop van elk apparaat Eiki EIP-X350 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Eiki EIP-X350 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Eiki EIP-X350 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Eiki EIP-X350 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Eiki EIP-X350 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Eiki EIP-X350 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Eiki EIP-X350 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Eiki EIP-X350 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
