Gebruiksaanwijzing /service van het product FlexScan F931 van de fabrikant Eizo
Ga naar pagina of 30
1 ENGLISH.
2 SAFETY SYMBOLS This manual uses the safety symbols below . They denote critical information. Please read them carefully . W ARNING Failure to abide by the information in a W ARNING may result in serious injury and can be life threatening.
CONTENTS 3 ENGLISH CONTENTS PRECA UTIONS ............................................................................. 4 1. INTRODUCTION ............................................................................ 8 1-1. F eatures ....................
4 PRECA UTIONS IMPORT ANT! • This product has been adjusted specifically for use in the region to which it was originally shipped. If operated outside the region to which it was originally shipped, the product may not perform as stated in the specifications.
ENGLISH PRECA UTIONS 5 OK OK • Place the unit on a strong, stable surface. A unit placed on an inadequate surface ma y f all, resulting in injur y or equipment damage. If the unit falls , disconnect the power immediately and hav e the unit check ed by a qualified ser vice engineer bef ore using it again.
6 PRECA UTIONS • Use the correct v oltage . * The unit is designed for use with a specific v oltage only . Connection to another voltage than specified in this User ’ s Man ual may cause fire , electric shock, or other damage. * Do not overload your power circuit, as this may result in fire or electric shock.
ENGLISH PRECA UTIONS 7 OK • Handle with care when carrying the unit. Disconnect the power cord and signal cables and remove the optional unit. Moving the unit with the cord or the option attached is dangerous. It may result in injury or equipment damage.
8 1. INTRODUCTION 1. INTR ODUCTION Thank you very much for choosing an EIZO Color Display Monitor . 1-1. Features • Horizontal scanning frequency of 30-130 kHz V e rtical scanning frequency of 50-16.
1. INTRODUCTION 9 ENGLISH 1-3. Contr ols & Connectors Front (1 ) ScreenManager ™ (2 ) BNC/D-SUB Selection Button (3 ) A UT O-SIZING Button (4 ) QuickSet ™ Control P ad (Hereinafter “ Control.
10 2. INST ALLA TION 2 . INST ALLA TION 2-1. Connecting the monitor to the PC • Be sure that the pow er switches of both of the PC and the monitor are OFF . 1. Plug the signal cable into the connector at the rear of the monitor and the other end of the cable into the video connector on the PC.
2. INST ALLA TION 11 ENGLISH 2. Plug the power cord into the power connector at the rear of the monitor . Then, plug the other end of the cord into a power outlet. 3. T urn on the monitor first, then the PC. The monitor ’ s power indicator will light up (green).
12 2. INST ALLA TION 2-2. Getting Ready f or Operation T r y each setting procedure if necessary in the following cases. 1. The display image size and/or position is incorrect Æ Æ Æ Æ Æ Press the AUTO-SIZING button on the front panel.
3. SCREEN ADJUSTMENT 13 ENGLISH 3. SCREEN ADJUSTMENT • Allow the monitor to stabiliz e for at least 30 minutes bef ore making image adjustments. 3-1. How to use the ScreenManager Use the control pad on the front panel. The control pad can be pressed in 5 directions, “ Enter ” , “ Up ” , “ Down ” , “ Left ” and “ Right ” .
14 3. SCREEN ADJUSTMENT Main menu Sub menu Adjustments and Settings See page Contrast — Screen contrast and brightness * — Size — Screen size — P osition — Screen position — Screen Side Pin Side pin balance — T rapez oidal Distor tion — Tilt Inclination — Unif or mity Uniformity p .
3. SCREEN ADJUSTMENT 15 ENGLISH 3-2. Color Adjust the color using by <Color> menu. 1. T o set the color temperature Æ Æ Æ Æ Æ Set the <T emperature>. T emperature can be set from 4,000 K to 10,000 K, in 500 K increments. (Including the 9,300 K default setting.
16 3. SCREEN ADJUSTMENT 3-4. P ower Sa v e There are two power save settings choose the setting which matches your environment. Set the power saving setting by using <Others> menu. • Do your part to conser ve energy , tur n off the monitor when you are finished using it.
3. SCREEN ADJUSTMENT 17 ENGLISH 3-5 . Adjustment Loc k Use the “ Adjustment Lock ” function to prevent any accidental changes. Locked function • Adjustments and settings in the ScreenManager . • AUTO-SIZING button. Unlocked function • Adjustment of contrast and brightness by the shortcut keys.
18 4. TROUBLESHOO TING 4. TR OUBLESHOO TING If a problem persists even after applying the suggested remedies, contact an EIZO dealer . *The bracket < > indicates the function of ScreenManager Problems P oints to chec k with possible solutions 1.
4. TROUBLESHOO TING 19 ENGLISH Problems P oints to chec k with possible solutions Use of the < Moir é Reduction > adjustment may cause a slight vibration.
20 4. TROUBLESHOO TING Problems P oints to chec k with possible solutions Adjust the < Contrast > (Contrast and Brightness). Some signal timing can be the cause of this problem. T o correct this, turn off the monitor , then hold down the “ down ” arrow key while turning on the monitor again.
5. CLEANING 21 ENGLISH 5. CLEANING Periodic cleaning is recommended to keep the monitor looking new and to prolong its operational lifetime. Clean the cabinet and CR T areas as follows: • Never use .
22 6. SPECIFICA TIONS 6. SPECIFICA TIONS CR T 55 cm (21 inch) class, 90 ° deflection Invar Shadow Mask with Anti Reflective SuperErgoCoat ® CR T Dot Pitch 0.25 mm (Horizontal: 0.21 mm) Scan Frequency Horizontal 30 kHz- 130 kHz (Automatic) V ertical 5 0 H z-160 Hz (Automatic) Recommended Resolution 1600 dots x 1200 lines Max.
6. SPECIFICA TIONS 23 ENGLISH Pin Assignment * D-Sub mini 15 pin connector * BNC Connector Connector Input signal H. Sync V . Sync Green Red Blue Separate sync H. Sync V . Sync Green Red Blue Composite sync H/V composite sync N/A Green Red Blue Sync on green N/A N/A Green composite sync Red Blue No .
24 7. GLOSSAR Y 7. GLOSSAR Y Color T emperature Color temperature is a method to measure the white color tone, generally indicated in degrees Kelvin. At high temperatures the white tone appears somewhat blue, while at lower temperatures it appears somewhat red.
7. GLOSSAR Y 25 ENGLISH Resolution Resolution is expressed as the number of dots (pixels) displayed on the screen. A larger number of dots produces a more sharply defined (a higher -resolution) image.
26 8. INDEX 8. INDEX A Adjustment lock ------------------------- 1 7 A UT O-SIZING button ------------------- 12 B BNC/D-SUB selection button -------- 1 7 Brightness --------------------------------- .
Congratulations! Y ou have just purchased a TCO ’ 99 approved and labelled product! Y our choice has provided you with a product developed for professional use. Y our purchase has also contributed to reducing the burden on the environment and also to the further development of environmentally adapted electronics products.
Environmental requirements Flame retardants Flame retardants are present in printed circuit boards, cables, wires, casings and housings. Their purpose is to prevent, or at least to delay the spread of fire. Up to 30% of the plastic in a computer casing can consist of flame retardant substances.
FCC Declaration of Conformity W e, the Responsible Party EIZO NANAO TECHNOLOGIES INC. 5710 W arland Drive, Cypr ess, CA 90630 Phone: (562) 431-5011 declare that the product T rade name: EIZO Model: FlexScan F931 is in conformity with Part 15 of the FCC Rules.
Hinweis zur Ergonomie : Dieser Monitor erfüllt die Anforderungen an die Ergonomie nach EK1/59-98, EK1/60- 98 mit dem V ideosignal, 1600 Punkte x 1200 Zeilen, RGB analog, 0,7 Vp-p und mindestens 85,0 Hz Bildwiederholfrequenz, non interlaced.
Een belangrijk punt na aankoop van elk apparaat Eizo FlexScan F931 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Eizo FlexScan F931 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Eizo FlexScan F931 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Eizo FlexScan F931 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Eizo FlexScan F931 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Eizo FlexScan F931 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Eizo FlexScan F931 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Eizo FlexScan F931 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
