Gebruiksaanwijzing /service van het product Digital 3000 AS van de fabrikant Elinchrom
Ga naar pagina of 16
Instructions for use Instructions for use Instructions for use Instructions for use Instructions for use POWER POWER POWER POWER POWER UNIVERSALITY UNIVERSALITY UNIVERSALITY UNIVERSALITY UNIVERSALITY TOTAL ASYMMETRY ASYMMETRY ASYMMETRY ASYMMETRY ASYMMETRY elinca sa switzerland www.
2 page Table of contents Table of contents Table of contents Table of contents Table of contents Safety notice 3 3 3 3 3 Control panel 4 4 4 4 4 Before you start 5 5 5 5 5 Technical data 6 6 6 6 6 Mai.
3 FLASH SYSTEMS STORE ELECTRICAL ENERGY IN CAPACITORS BY APPLYING HIGH VOLTAGE. FOR YOUR SAFETY, NEVER OPEN YOUR FLASHES. ONLY AN AUTHORISED SERVICE ENGINEER SHOULD OPEN OR ATTEMPT TO REPAIR THE UNITS.
4 1 . Mains inlet power socket 2. Mains fuse (16 AT, slow blow) 3. Charge speed selectors - slow charge - normal charge - fast charge 4. Mains switch 5. Photocell and IR-Receiver 6. Photocell on/off 7. Sync.-socket with security lock 8. Open flash with charge indicator 9.
5 1) Mains connection The unit is manufactured to run on 200-240 V, 50/60 Hz. Before connecting them for the first time, make sure that your mains supply and the rating set on the equipment (electrical specification plate) are compatible.
6 Display Ws f-stop Power 9 3000 (180.3) 1/1 8 1500 (128.3) 1/2 7 750 (90.3) 1/4 6 375 (64.3) 1/8 5 188 (45.3) 1/16 5** 95 (32.3) 1/32 with 2 lampheads 5*** 62 (22.7) 1/48 with 3 lampheads on mains 230 V- 50 Hz 1.8 - 10 s 0.8 - 4.5 s 0.7 - 3.5 s on mains 115 V- 60 Hz 2 - 11s 0.
7 Standard type 5 x 20 mm, 16 AT (tempered). Before exchanging a blown fuse, switch off the unit and remove mains cable. Depress and turn the fuse holder anti-clockwise 1/8th and remove it. If the new fuse blows immediately upon reconnection return the pack to an ELINCHROM service centre for a check-up.
8 N.B. For even less load on the power supply line use and jointly. The modelling lamps automatically extinguish when the generator is charging but illuminate when the charge cycle ends. When the indicator of the touch (12) is illuminated and will sound whenever a command has been accepted by the generator (useful when using the IR handset).
9 10. POWER INDICATOR «BLINKS» 8. TOT AL POWER 9. INDIVIDUAL POWER OUTPUT This display indicates the total power released through the lampheads. The variation is a single steps or if the touch is held it will run continuously. The first number indicates charges by full f-stop, the second number by 1/10 f-stop.
10 11. SWITCHABLE PHOTOCELL (SLAVE) 12. SYNCHRONISATION SOCKET 12. ACCESSORY SOCKET The Amphenol secure locking system with standard 5 m cable is retained. Longer cables may be used. N.B. Do not link ELINCHROM units by cable to other manufacturers sync outlets.
11 The modelling lamp will only function when the lamphead is switched on (note : there is an overheating control switch ON/OFF in the lamphead). - Simple ON/OFF with ON setting indicated.
12 14. LAMPHEADS ON/OFF 15. FUSES FOR LAMPHEADS 13. LAMPHEADS Important : When plugging in a lamphead connector, first push in the front part, then firmly press in the whole plug, the rear part being secured by the locking spring. Different modelling lamps require corresponding fuses.
13 16. PROTECTIVE PIREX DOME For use with standard halogen lamp GX 6.35 socket. Transparent, matt or yellow (400 ° K colour correction), can be fitted to all lampheads, except R heads (rectangular heads) for which clear or matt security filters are available.
14 18. LAMPHEAD COMPATIBILITY * 2000 Ws with MICRO series ** 3000 Ws with MICRO series MAXIMUM Compatible with : Digital 1500/3000 AS and MICRO AS ADAPTABLE 4000 Ws Digital S S4000 T4 T A4 A4 A Box Li.
15 Accessories overview Accessories overview Accessories overview Accessories overview Accessories overview Reflectors Reflectors Reflectors Reflectors Reflectors code code code code code Wide angle .
16 Visit our W eb site : www.elinchrom.com Elinca s.a E. Digital 3000 AS (73316) Printed in Switzerland.
Een belangrijk punt na aankoop van elk apparaat Elinchrom Digital 3000 AS (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Elinchrom Digital 3000 AS heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Elinchrom Digital 3000 AS vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Elinchrom Digital 3000 AS leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Elinchrom Digital 3000 AS krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Elinchrom Digital 3000 AS bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Elinchrom Digital 3000 AS kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Elinchrom Digital 3000 AS . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.