Gebruiksaanwijzing /service van het product 350108 van de fabrikant Aleratec
Ga naar pagina of 62
USER GUIDE Aleratec ® HDD PortaCruiser™ Part No. 350108.
www .aleratec.com Copyright/Model Identification The content of this manual is for informational purposes only and is subject to change without notice.
www .aleratec.com Radio/TV Interference Statement The equipment described in this guide emits radio frequency energy . If it is not installed in accordance with the manufacturer ’ s instructions, it may cause interference with radio or television reception.
www .aleratec.com Safety Regulations W ARNING T o prevent re or shock hazard, do not expose the unit to rain or moisture. T o avoid electrical shock, do not open the housing.
www .aleratec.com T able of Contents Introduction ................................................................................................... 1 Product Features ..................................................................................
www .aleratec.com T able of Contents Using the HDD PortaCruiser ..................................................................... 30 Duplicator Mode ................................................................................................30 Advanced Setup Menu .
www .aleratec.com 1 Introduction Thank you for purchasing the HDD PortaCruiser . Please read this User Guide thoroughly before using this product. Product Features The HDD PortaCruiser is a Hard Disk Drive Duplicator and Dual Disk RAID Controller .
www .aleratec.com 2 Introduction Key Items Display Panel (see page 3) Power Switch Controller Buttons SA T A T arget Drive Connector SA T A Source Drive Connector IDE T arget Drive Port IDE T arget Po.
www .aleratec.com 3 Introduction HDD PortaCruiser Display Panel and Buttons (Actual display may vary from illustration) LCD display shows all functions and messages 1. UP 2. arrow is used to scroll backward through functions or menus DOWN 3. arrow is used to scroll forward through functions or menus ENT 4.
www .aleratec.com 4 Precautions Before installing your HDD PortaCruiser , please read the following. Installation A void placing the HDD PortaCruiser in a location subject to: High humidity • High t.
www .aleratec.com 5 Overview Power Up Sequence During the normal power-up sequence of the HDD PortaCruiser , the following information will be displayed. Figure 1 shows the rmware version • Figure 2 shows the memory initialization • Figure 3 shows the scanning of the drives • Figure 4 shows the number of drives loaded.
www .aleratec.com 6 Overview Understanding RAID RAID (Redundant Array of Independent Disks) is a system composed of many hard drives; that is, multiple physical drives form a single virtual drive to be recognized by the system. Different RAID modes have dif ferent advantages and disadvantages.
www .aleratec.com 7 Overview Duplicator Main Menu In Duplicator mode, there are eight main menu items that can be seen in the HDD PortaCruiser Copy Controller Display Panel. These are: 1. 2. 3. 4. 5. 6. 7. 8. Note: The Advanced Setup function is a hidden menu.
www .aleratec.com 8 Overview Duplicator Subfunctions The “Setup” menu has eight (8) subfunctions. These are: 6-01 Language 6. Setup ENT ESC RESET MUTE 6-02 DMA Mode 6-03 Copy Size 6-04 Sta.
www .aleratec.com 9 Overview The Duplicator “Advanced Setup” menu has eight (8) subfunctions. These are: 8-01 ReScan Bus Delay 8-02 Read Error Skip 8-03 Quick Erase HDD 8-04 H/W Diagnostic 8-05 Load Default 8-06 Link Option (for USB Mode) 8-07 USB Auto Link 8-08 Copy HP A 8.
www .aleratec.com 10 Overview Dual Disk RAID (USB) Mode Main Menu In USB mode, the options seen in the HDD PortaCruiser Display Panel depend on the RAID mode of the system. These are: Normal Mode 1. 2. 3. 4. 5. JBOD Mode 1. 2. 3. 4. 1. Duplicator Mode ENT ESC RESET MUTE 2.
www .aleratec.com 11 Overview RAID0 Mode 1. 2. 3. 4. RAID1 Mode 1. 2. 3. 4. 1. Duplicator Mode ENT ESC RESET MUTE 2. Information ENT ESC RESET MUTE 4. Initial RAID0 ENT ESC RESET MUTE 3. Change RAID Mode ENT ESC RESET MUTE 1.
www .aleratec.com 12 Using the HDD PortaCruiser Loading the Hard Drives IDE Drives Use an IDE cable (not included) to connect the source/target hard drive’ s IDE 1. port to the HDD PortaCruiser ’ s Source/T ar get IDE port. Use an IDE cable (not included) to connect the source/target hard drive’ s power 2.
www .aleratec.com 13 Using the HDD PortaCruiser Removing Hard Drives Remove the IDE and power cables (for IDE drives) or slide the hard drive away 1. from the HDD PortaCruiser unit (for SA T A drives). Note: Do not attempt to remove the hard drive if the drive activity LED is on or the unit is in the middle of a process.
www .aleratec.com 14 Using the HDD PortaCruiser Duplicator Mode Main Menu: Copy HDD The “Copy HDD” function performs an actual copy from the source HDD to the target HDD. The tar get HDD must be at least as large as the source. The HDD PortaCruiser will copy every block of capacity on the source HDD.
www .aleratec.com 15 Using the HDD PortaCruiser Duplicator Mode Main Menu: Compare HDD The “Compare HDD” function performs a comparison of data from the source hard drive to the data on the target hard drive. W ith the source and target HDDs loaded use the arrow buttons ( 1.
www .aleratec.com 16 Using the HDD PortaCruiser Duplicator Mode Main Menu: PreScan Source The “PreScan Source” scans the source hard drive to determine if it can be read correctly . W ith the source HDD loaded, use the arrow buttons ( 1. or ) to select “PreScan Source”.
www .aleratec.com 17 Using the HDD PortaCruiser Duplicator Mode Main Menu: ReScan Bus The “ReScan Bus” function causes the HDD PortaCruiser to redetect connected hard drives. This can be used when you change drives without restarting the system. Use the arrow buttons ( 1.
www .aleratec.com 18 Using the HDD PortaCruiser Duplicator Mode Main Menu: Source HDD Size The “Source Size” function is used to display the capacity of the source hard drive. W ith the source HDD loaded, use the arrow buttons ( 1. or ) to select “Source size”.
www .aleratec.com 19 Using the HDD PortaCruiser Duplicator Mode Main Menu: USB RAID Mode This function allows you to switch to the Dual Disk RAID Controller mode. Use the arrow buttons ( 1. or ) to select “USB RAID Mode”. The following screen will be displayed.
www .aleratec.com 20 Using the HDD PortaCruiser Duplicator Mode Setup Menu The “Setup” menu contains conguration options for the HDD PortaCruiser . It is suggested to use the factory defaults for optimum performance. Use the arrow buttons ( 1. or ) to select “Setup”.
www .aleratec.com 21 Using the HDD PortaCruiser Duplicator Mode Setup Menu: 6-01 Language This option allows you to select the language that is used for the display . Use the arrow buttons ( 1. or ) select “Setup”. The following screen will be displayed.
www .aleratec.com 22 Using the HDD PortaCruiser Duplicator Mode Setup Menu: 6-02 DMA Mode This function is used to specify the Ultra DMA mode. Use the arrow buttons ( 1. or ) select “Setup”. The following screen will be displayed. Press 2.
www .aleratec.com 23 Using the HDD PortaCruiser Duplicator Mode Setup Menu: 6-03 Copy Size This function is used to specify the amount of source disk data to copy to the target drive. Use the arrow buttons ( 1. or ) select “Setup”. The following screen will be displayed.
www .aleratec.com 24 Using the HDD PortaCruiser Duplicator Mode Setup Menu: 6-04 Startup Menu This option lets you select any of the functions (except “Setup”) as the initial function that appears when the HDD PortaCruiser is powered on. Use the arrow buttons ( 1.
www .aleratec.com 25 Using the HDD PortaCruiser Duplicator Mode Setup Menu: 6-05 Auto Compare This option allows you to choose whether or not to automatically compare the source and target hard drive after every copy operation. Use the arrow buttons ( 1.
www .aleratec.com 26 Using the HDD PortaCruiser Duplicator Mode Setup Menu: 6-06 Copy with Detect This option allows you to choose whether or not to automatically rescan for connected drives immediately before a copy operation. Use the arrow buttons ( 1.
www .aleratec.com 27 Using the HDD PortaCruiser Duplicator Mode Setup Menu: 6-07 Button Sound This option allows you to enable or disable the beeping sound heard when you press a button. Use the arrow buttons ( 1. or ) select “Setup”. The following screen will be displayed.
www .aleratec.com 28 Using the HDD PortaCruiser Duplicator Mode Setup Menu: 6-08 Device Info This option displays information about any hard drives connected to the HDD PortaCruiser . Use the arrow buttons ( 1. or ) to scroll to “Setup”. The following screen will be displayed.
www .aleratec.com 29 Using the HDD PortaCruiser Duplicator Mode Setup Menu: 6-09 System Info This function displays information about the HDD PortaCruiser , including the current rmware version. Use the arrow buttons ( 1. or ) to select “Setup”.
www .aleratec.com 30 Using the HDD PortaCruiser Duplicator Mode Advanced Setup Menu The “Adv Setup” menu contains additional conguration options for the HDD PortaCruiser . Press and hold the 1. ESC button for 3 seconds to enter Adv Setup. The following screen will be displayed.
www .aleratec.com 31 Using the HDD PortaCruiser Duplicator Mode Advanced Setup Menu: 8-01 ReScan Bus Delay This function is used to set the time interval between the system’ s re-scans of all connected HDD devices. Press and hold 1. ESC for about 3 seconds to access the “Adv Setup” menu.
www .aleratec.com 32 Using the HDD PortaCruiser Duplicator Mode Advanced Setup Menu: 8-02 Read Error Skip This function can be enabled to ignore any error that occurs during copying. By default, the HDD PortaCruiser will halt the copy operation when it encounters an unreadable area of the source hard disk and display an error .
www .aleratec.com 33 Using the HDD PortaCruiser Duplicator Mode Advanced Setup Menu: 8-03 Quick Erase HDD This function is used to erase the data of a hard drive quickly . W arning : Backup any important data before using this function. Press and hold 1.
www .aleratec.com 34 Using the HDD PortaCruiser Duplicator Mode Advanced Setup Menu: 8-04 H/W Diagnostic This function is used to test various components of the HDD PortaCruiser . Press and hold 1. ESC for about three seconds to access the “Adv Setup” menu.
www .aleratec.com 35 Using the HDD PortaCruiser Duplicator Mode Advanced Setup Menu: 8-05 Load Default This function is used to restore all factory settings of the HDD PortaCruiser back to their original defaults. Press and hold 1. ESC for about three seconds to access the “Adv Setup” menu.
www .aleratec.com 36 Using the HDD PortaCruiser Duplicator Mode Advanced Setup Menu: 8-06 Link Option This function is used to decide if “7.USB RAID Mode” will be displayed in the display panel. Press and hold 1. ESC for about three seconds to access the “Adv Setup” menu.
www .aleratec.com 37 Using the HDD PortaCruiser Duplicator Mode Advanced Setup Menu: 8-07 USB Auto-Link This function sets the HDD PortaCruiser to immediately enter Dual Disk RAID Controller (USB) mode on startup. This allows direct control of the unit from a PC.
www .aleratec.com 38 Using the HDD PortaCruiser Duplicator Mode Advanced Setup Menu: 8-08 Copy HP A If the source hard disk contains a Host Protected Area (HP A), this option allows you to choose whether or not to copy data within the HP A. Press and hold 1.
www .aleratec.com 39 Using the HDD PortaCruiser Dual Disk RAID Controller (USB) Mode Main Menu: Duplicator Mode Option This function allows you to switch to the Duplicator mode. Use the arrow buttons ( 1. or ) to select “Duplicator Mode”. The following screen will be displayed.
www .aleratec.com 40 Using the HDD PortaCruiser Dual Disk RAID Controller (USB) Mode Main Menu: Information Option This function displays information about the HDD PortaCruiser and any attached hard drives. Use the arrow buttons ( 1. or ) to select “Information”.
www .aleratec.com 41 Using the HDD PortaCruiser Dual Disk RAID Controller (USB) Mode Main Menu: Change RAID Mode Option This function allows you to choose the RAID mode for the Dual Disk RAID Controller . Use the arrow buttons ( 1. or ) to select “Change RAID Mode”.
www .aleratec.com 42 Using the HDD PortaCruiser Dual Disk RAID Controller (USB) Mode Main Menu: Change RAID Mode Option Changing to Normal Mode - continued Use the arrow buttons ( 6. ) to select “Y es” and press ENT to select. The new main screen will be shown which displays the new mode and capacity .
www .aleratec.com 43 Using the HDD PortaCruiser Changing to RAID0 Mode The system will prompt you to conrm that you wish to change modes. 4. Use the arrow buttons ( 5. or ) to select “Y es” and press ENT to select. The system will then prompt you to conrm that you understand data may be lost.
www .aleratec.com 44 Using the HDD PortaCruiser Dual Disk RAID Controller (USB) Mode Main Menu: Change RAID Mode Option Changing to RAID1 Mode - continued Use the arrow buttons ( 6. ) to select “Y es” and press ENT to select. The system will then ask you whether or not you want to preserve the Source drive’ s data.
www .aleratec.com 45 Using the HDD PortaCruiser Dual Disk RAID Controller (USB) Mode – Normal Only Main Menu: D1 Drive Select Mode Option This function allows you to enable or disable the Source drive. Use the arrow buttons ( 1. or ) to select “D1 Drive Select”.
www .aleratec.com 46 Using the HDD PortaCruiser Dual Disk RAID Controller (USB) Mode – JBOD Only Main Menu: Initial JBOD Option This function allows you to initialize your disks for JBOD. Use the arrow buttons ( 1. or ) to select “Initial JBOD”.
www .aleratec.com 47 Using the HDD PortaCruiser Dual Disk RAID Controller (USB) Mode – RAID0 Only Main Menu: Initial RAID0 Option This function allows you to initialize your disks for RAID0. Use the arrow buttons ( 1. or ) to select “Initial RAID0”.
www .aleratec.com 48 Using the HDD PortaCruiser Dual Disk RAID Controller (USB) Mode – RAID1 Only Main Menu: Initial RAID1 Option This function allows you to initialize your disks for RAID1. Use the arrow buttons ( 1. or ) to select “Initial RAID1”.
www .aleratec.com 49 Specifications Power Requirements V oltage: 100-240V Current: 50-60Hz Dimensions (depth x width x height) D: 150mm W : 116mm H: 27mm (5.9” x 4.6” x 1.0”) W eight 235g (0.5 Lbs.) Note: Specifications subject to change without notice.
www .aleratec.com 50 T echnical Support After reading this User Guide, if you need additional assistance with this product, please contact Aleratec T echnical Support. Our technical staff will be happy to assist you, but they may need your help to better assist you.
www .aleratec.com 51 Service and Support Aleratec, Inc., Limited Warranty This Limited W arranty covers defects encountered in the course of normal use of this product and does not apply to damage from improper use, abuse, accidents, unauthorized service, or inadequate packaging when shipping the product to Aleratec, Inc.
www .aleratec.com 52 Service and Support Please Note: This W arranty is valid only within the United States and Puerto Rico, and applies only to products that are new and unopened on the date of purchase.
www .aleratec.com 53 Service and Support T o Obtain Warranty Service: Y ou must ship your subsystem to the authorized dealer where your subsystem was purchased within the one year warranty period and no later than thirty days after discovery of claimed defect, whichever occurs rst.
www .aleratec.com 54 T echnical Support F AX Back Form Aleratec, Inc. T echnical Support Fax Back Form Please record the following information to help expedite any warranty claim: Model No.
www .aleratec.com Notes:.
Document Number: 9399065_ENG_Rev . C Copyright © 2009 Specifications subject to change without notice. Aleratec, Inc. 9851 Owensmouth Avenue Chatsworth, CA 91311 U.
Een belangrijk punt na aankoop van elk apparaat Aleratec 350108 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Aleratec 350108 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Aleratec 350108 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Aleratec 350108 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Aleratec 350108 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Aleratec 350108 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Aleratec 350108 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Aleratec 350108 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
