Gebruiksaanwijzing /service van het product N150 van de fabrikant ENCORE
Ga naar pagina of 97
ENHWI-N3 802.1 1n Wireless Router User Manual 1.
T ABLE OF C ONTENTS 1 INTRODUCTION ........................................................................................................................3 2 KEY FEA TURES ..............................................................................
I - Introduction Congratulations on your purchase of ENHWI-N3 802.11n Wireless Router. ENHWI-N3 is backward compatible with wireless devices running under the 802.
II - Key Features Features Advantages Incredible Data Rate up to 150 Mbps** Easily handled heavy data loads such as MPEG audio / video streaming, IEEE 802.11b/g/n Compliant Fully Interoperable with IEEE 802.11b/g/n compliant devices with legacy protection Four 10/100 Mbps Fast Switch RJ-45 Ports (with Auto-Crossover) Scalability.
III - Package Contents Check and make sure that none of the items listed below are missing. Do not discard the p acking materials, in case of return; the unit must be sh ipped back in its original p ackaging. 1. ENHWI-N3 Wireless 802.11n Router 2. 100V~240V Power Adapter (Use only the supplied power adapter) 3.
IV - Product Layout Front Panel V iew LED Light s Description POWER Lights up in Red when powered ON. Blinks on TEST/RESET WLAN Lights up in Green when Wireless LAN is enabled.
Rear V iew Item Description Reset Press and release this button to reboot the device. Press and hold this button for 10 seconds to load the factory default settings of the system.
V - Network + System Requirements T o begin using the ENHWI-N3, make sure you meet the following as minimum requirements: h PC / Notebook Computer h Operating System – Microsoft™ Windows ® 98SE/ME/XP/2000/ Windows Vi sta™ h 1 Free Ethernet port h Wi-Fi adapter card – optional.
VII - Setup LAN, WAN LAN connection: Connect Ethernet cable between your PC/Notebook LAN port & one of the 4 available LAN ports on ENHWI-N3. W AN connection: Connect Ethernet cable between W AN port of your ADSL/CABLE modem & W AN port of ENHWI-N3.
VIII - PC Network Adapter Setup ( Windows XP ) • Assuming your PC or Laptop is equipped with a Network Interface Card. Click on START Æ select “ Control panel ” Æ From the Control Panel Window.
• Click to Highlight the “ Internet Protocol (TCP/IP) ” then click “ Properties ” button • Select the “General” tab. a. ENHWI-N3 supports the DHCP function, please select both “ Obta.
IX - Power up the ENHWI-N3 Connect the supplied power-adapter to th e power port and conne ct it to a wall power outlet. The ENHWI-N3 autom atically enters and run the self-test phase. The Power LED will light a steady red ligh t indicating that the ENHW I-N3 is ready for operation.
A welcome screen will pop up a few seconds and then will disappear. 13.
NOTE: The product picture may be different from what you have Click Setup Wizard to run basic setup settings of your ENHWI-N3. Click User Manual to open the user manual. Click Adobe Reader to install Adobe Acrobat reader on your PC/Notebook. Click EXIT when finish or anytime you want to abort.
Setup Wizard Click to proceed. Click <Exit> to abort. 15.
Make sure your DSL/CABLE modem is setup and working prior to this installation procedures. If not, call your Internet Service Provider and have them check and help you in setting up your DSL/Cable modem.
Check the MODEM and ENHWI-N3 connection. It should be as shown below. 17.
Check power connection for modem as well as ENHWI-N3. Make sure the antenna is connected to rear panel of ENHWI-N3. Click <Next> to proceed. Notice the LED will light up at this stage.
Click to configure WAN & Wireless settings. 19.
Enter the factory default username is admin and password is also admin. Click to continue. Your default browser screen will connect to the ENHWI-N3 User Interface screen using the factory default address http://192.168.0.1 . Click to enter the mode selection screen.
Select the mode your ENHWI-N3 is going to use. The Setup Wizard will skip the WAN configuration under AP Repeater Mode . Click and your ENHWI-N3 will automatically detect your “Internet” Network settings.
The Smart Wizard will detect the DHCP and PPPoE connections automatically. In the picture above it shows that the Smart Wizard detected a DHCP server. You can choose the detected service type or select “Others” to setup the WAN settings manually.
Here, you can configure the host name and MAC address of the ENHWI-N3. The “ Clone MAC Address” button clones the MAC address of your PC and use it as the MAC address of your ENHWI-N3 router instead of the real MAC address of the router. The Smart Wizard has finished setting up the WAN Configuration portion.
Setting up Wireless LAN Enter the name for your wireless network SSID (the default is ENCORE59FE74) and security key (default is 1234567890). Move and point your mouse over to the security level blocks from the weakest (red block) to the strongest (green block), an d click on the selected block to se lect the le vel of security you desired.
To save configuration changes click NOTE: After the Wireless settings are saved and the ENHWI-N3 is rebooted, you need to reconnect your WLAN client using the new security settings you just changed. You will need to reenter the new wireless security key for the cli ent and the ENHWI-N3 reestablish wireless connections.
XI – How to login to the ENHWI-N3 web based Graphical User Interface The ENHWI-N3 use a web based user interface for setting up your router’s configuration, it can be access through your web browser such as Internet Explorer or Mozilla Firefox. ENHWI-N3 web based user interface login procedure 1.
ENHW-N3 Home Page Screen XII - The AP Router Mode SYSTEM Shows the Uptime, Hardware information, Serial number as well as the Firmware version information and other vital information z S tatus T ab This page allows you to monitor the status of your router.
1. WAN Settings : Scroll down to see the full information. This section displays whether the WAN port is connected to a Cable / DSL modem. It also displays the router’s WAN IP address, Subnet Mask, ISP Gateway, MAC address and the Primary DNS.
2. LAN Settings: Scroll down to see this section. Displays the ENHWI-N3 Router LAN port’s current information. It also shows whether the DHCP Server is enabled or disabled. 2. WLAN Settings: Scroll down to see this section. This section displays the current WLAN configuration settings.
The LAN Tab is where LAN settings can be ch ange. If you are an entry level user, after hooking up the cables, try to access the internet from your computer. If you can open a website with no problem, leave the settings as it is. If changes were made, click the button to save the changed configurations.
DHCP Server DHCP Server: This can be enabled or disabled, “Enabled” by default. Lease time: Lease time assigned to all IP address by the DHCP server. Start IP: This is the first IP address in the IP pool range in which are being assigned and leased to DHCP clients.
the <Refresh> button to update the available information. Click the <Refresh> button to get the updated table. You can click to put a check mark on “ Enable Static DHCP IP “. It is possible to add more static DHCP IP addresses. They are listed in the table “ Current Static DHCP Table “.
settings. The “Schedule” table screen lists the pre-scheduled services. Select any of the schedules by using the check box located on the right side of each line to edit or Delete selected schedule line.
On this “Event Log” screen, it displays all events and events information occurred after the start-up. Scroll down to see more. The Event Log can be saved to the local file-storage device such as ha rd disc drive by using the <Save> button, or the Event Log can be emptied using the <Clear> button.
z Language Tab This is where you select preferred language. 35.
WIZARD Click Wizard to configure the basic functionalities of the EN HWI-N3 Router. A popup Setup Wizard Window will be immediately displayed. If the popup window for Setup Wizard failed to appear check your Popup Settings and make sure popup is allowed at least temporarily for this purpose.
- Dynamic IP Use the MAC address when registering for the Internet ser vice, and do not change it unless required by your ISP . If your ISP use the MAC address of the Ethernet card as an identifier , connect only the PC with the registered MAC address to the broadband router and click the <Clone MAC Address> button.
Host Name: This is optional. MAC address: The default value is set to the W AN’s physical address or MAC of the broadband router . - S t atic IP If your ISP Provider has assigned a fixed pub lic IP .
- Point-to-Point Protocol over Ethernet(PPPoE) 39.
Login / Password: Enter the PPPoE username and password assigned by your ISP Provider . Service Name: This is optional. Maximum T ransmission Unit (MTU): This is the maximum size of the packet s.
PPTP allows the secur e connection over the Internet by simply dialing in to a local point provided by your ISP provider . The im age screen allows client PCs to establish a normal PPTP session and provides hassle-free configuration of the PPTP client on each client PC.
Radio: You can turn on/off wireless radio. If wireless Radio is turned off, the ENHWI-N3 will not take wireless connections. Mode: Three operation modes for selections, the AP router and AP router with WDS . If you choose AP Router Mode, there will be two selections under it, the AP or WDS function in the drop-down menu.
ESSID1 to ESSID4: ESSID is the name o f your wireless network. It is recommended to use a unique name to identify your wireless device in the LAN. This is case sensitive and up to 32 printable characters. Auto Channel: Disable by default. If Enabled will automatically search all channels and automatically change to the clearest channel detected.
MAC address 1~4: Please enter the MAC address(es) of the neighboring APs that participates in the WDS. A maximum of 4 devices are allowed. Set Security: WDS Security depends on your AP security settings. Note: It does not support mixed mode such as WPA-PSK/WPA2-PSK Mixed mode.
- Advanced On this tab you can set the advanced wireless settings. If you’re in doubt what to enter or use here, leave these settings as it is. This is for advance users only. Wron g parameters can make the router un-operational. Fragment Threshold: Default value is 2346.
DTIM Period: Default value is 1. Enter a value between 1 and 255 for the Delivery Traffic Indication Message (DTIM). A DTIM is a countdown informing clients of the next window for listening to broadcast and multicast messages. Data Rate: The “Data Rate” is the rate that this access point uses to transmit data packets.
ESSID Selection: ENHWI-N3 router supports multiple ESSID, you can name you r wireless ESSID here. Broadcast ESSID: If you enabled “Broadcast ESSID”, every wireless station located within the coverage of this Router can see this ESSID. If you are building a public wireless network, enabling this feature is recommended.
IEEE 802.1x is an authentication protocol using RADIUS server. When this is Enabled, every LAN user must use an account to login to this Access Point before accessing the wireless LAN. The authentication is proce ssed by a RADIUS server. This mode only authenticates users by IEEE 802.
Authentication Type: There are two authentication types: "Open Sy stem" and "Shared Key" . Both AP and wireless client must be configured with the same authentication type. Key Length: You can select the WEP key length for encryption, 64-bit or 128-bit.
64-bit WEP: input 10-digits Hex values (in the "A-F", "a-f" and "0-9" range ) or 5-digit ASCII character as the encryption keys. 128-bit WEP: input 26-digit Hex values (in the "A-F", "a-f" and "0-9" rang e) or 13-digit ASCII characters as the encryption keys.
WP A-RADIUS Encryp tion Wi-Fi Protected Access ( WPA ) is an advanced security standard. You can use an external RADIUS server to aut henticate wireless stations and provide the session key to encrypt data during communication. It uses TKIP or CCMP ( AES ) to change the encryption key frequently.
- MAC Address Filtering This wireless router supports MAC Address Control, which prevents unauthorized clients from accessing your wireless network. Enable wireless access control: Enable the wireless.
Click <Apply> at the bottom of the screen to save the above configurations. - Wi-Fi Protected Setup™ (WPS™) WPS™ is the simplest way to establish a connection between the wirele ss clients and the wireless router.
WPS Current Status: If the wireless security (encryption) function of this wireless router is properly set, you’ll see a ‘Configured’ message here. Otherwise, you’ll see ‘ UnConfigured’ . Click the “Release Configuration” can clear the security settings of the 1 st SSID.
- Client List WLAN Client Table shows the Wireless clients associated to this Wireless Router. - Policy The Broadband router can allow you to set up the Wireless Access Policy up to 4 SSID’s.
FIREW A LL The Broadband router provides extensive firewa ll protection by restricting connectio n parameters, thus limiting the risk of hacker attacks, and d efending against a wide array of common Internet attacks.
- Demilit arized Zone (DMZ) If you have a client PC that cannot run an Internet application (e .g. Games) properly behind the NAT firewall, then you can open up the firewall restrictions to unrestricted two-way Internet access by defining a DMZ Host.
The Broadband router's firewall can block common hacker attacks, including Denial of Service, Ping of Death, Port Scan and Sync Flood. If Internet attacks occur the router can log the events.
Enable MAC Filtering: Check to enable or disable MAC Filtering. Deny: If you select “ Deny ” then all clients will be allowed to access Internet except the clients in the list below. Allow: If you select “ Allow ” then all clients will be denied to access Internet except the PCs in the list below.
Add PC MAC Address Fill in “ LAN MAC Address ” and <Description> of the PC that is allowed / denied to access the Internet, and t hen click <Add> . If you find any typo before adding it and want to retype again, just click <Reset> and the fields will be cleared.
- IP Filter Enable IP Filtering: Check to enable or uncheck to disable IP Filtering. Deny: If you select “ Deny ” then all clients will be allowed to access Internet except for the clients in the list below. Allow: If you select “ Allow ” then all clients will be denied to access Internet except for the PCs in the list below.
select the PC you want to remove in the table and then click <Delete Selected> . If you want to remove all PCs from the table, just click the <Delete All> button. Click <Apply> at the bottom of the screen to save the above configurations.
Remove URL Keyword If you want to remove some URL keywords from the " Current URL Blocking Table ", select the URL keyword you want to remove in the table and then click <Delete Selected> . If you want remove all URL keywords from the table, click <Delete All> button.
ADV ANCED - Network Address T ranslation (NA T) Network Address Translation (NAT) allows multiple users at your local LAN site to access the Internet using a single Public I P Address or multiple Public IP Addresses.
Enable Port Mapping: Enable or disable port mapping function. Description: description of this setting. Local IP: This is the local IP of the server behind the NAT firewall.
Fill in the " Local IP ", “ Protocol ”, “ Port Range ” and " Description " of the setting to be added and then click " Add ". Then this Port Mapping setting will be added into the " Current Port Mapping Table " below.
Enable Port Forwarding: Enable or disable Port Forwarding. Description: The description of this setting. Local IP / Local Port: This is the LAN Client/Host IP address and Port number that the Public Port number packet will be sent to. Protocol: Select the port number protocol type (TCP, UDP or both).
Fill in the " Description " , " Local IP ", " Local Port ", " Protocol " and “ Public Port ” of the setting to be added and then click <Add> button. Then this Virtual Server setting will be added into the " Current Port Forwarding Table " below.
Enable Trigger Port: Enable or disable the Port Trigger function. Trigger Port: This is the outgoing (Outbound) range of port numbers for this particular application. Trigger Type: Select whether the outbound port protocol is “ TCP ”, “ UDP ” or “ BOTH ”.
Add Port Triggering Fill in the " Trigger Port ", " Trigger Typ e ”, “ Public Port ”, " Public Type ", " Public Port " and " Description " of the setting to be added and then Click <Add> . The Port Triggering setting will be added into the " Current Trigger- Port Table " below.
- UPNP With UPnP, all PCs in you Intranet will discover this router automatically. So, you don’t have to configure your PC and it can easily access the Internet through this router.
Enable / Disable UPnP: You can enable or Disable the UPnP feature here. After you enabled the UPnP feature, all client systems that support UPnP, like Windows XP, can discover this router automatically and access the Internet through this router without having to configure anything.
Unlimited Priority Queue: The LAN IP address will not be bounded in the QoS limitation. High/Low Priority Queue: This can put the packet s in the protocol and port range to High/Low QoS Queue. Bandwidth Allocation: This can reserve / limit the throughput of spe cific protocols and port range.
T ype: S pecify the direction of packet s. Upload / Download or both. IP range: S pecify the IP address ran ge. Y ou could also fill one IP address Protocol: S pecify the packet type. The default ALL will put all packets i n the QoS priority Queue. Port range: S pecify the Port range.
- Routing Y ou can set Enable S tatic Routing to let the router forward p ackets usin g your routing policy . Destination LAN IP: S pecify the destination LAN IP address of st atic routing rule.
Subnet Mask: S pecify the Subnet Mask of static routing rule. Default Gateway: S pecify the default gateway of static routing rule. Hop s: S pecify the Max Hops number of static r outing rule.
Remote managemen t Allows you to designate a host in the Internet. The ability to configure the Broadband router from a remote site. Enter the designated host IP Address in the Host IP Address field.
Time Zone: Select the time zone of the country you are currently located. The router will set its time based on your selection. NTP Time Server: The router can be set up to use external NTP Time Server. Daylight Savings: The router can also be set to autom atically adjust to the Daylight Savings changes.
PC Date and Time: This field would display your computer’s date and time. Daylight Savings: The router can also take Daylight Savings into account. If you wish to use this function, you must select the Daylight Savings Time period and check/tick the enable box to enable your daylight saving configuration.
Enable/Disable DDNS: Enable or disable the DDNS function of this router Server Address: Select a DDNS service provider Host Name: Fill in your static domain name that uses DDNS. Username: The account that your DDNS service provider assigned to you. Password: The password you set for the DDNS service account above.
- Diagnosis In this page lets you run diagnosis to your network status. - Firmware This page allows you to upgrade the router’s firm ware. To upgrade the firmware of your Broadband router, you need to download the firmware file to your local hard disk, and enter that file name and path in the appropriate field on this page.
Once you’ve selected the new firmware file, click < Apply > at the bottom of the screen to start the upgrade process - Back-up This page allows you to save the current router configurations. When you save the configurations, you also can restore the saved configurations into the router through the Restore Settings .
Backup Settings: This can save the current Broadband router configuration to a file named " config.bin " on your PC. You can also use the <Upload> button to restore the saved configuration to the Broadband router.
XIII - Repeater Mode Repeater mode has limited settings compared to the AP mode. Choose “Repeater mode” on the top right corner of the configuration page. System restarts and connects to the IP address http://192.168..0.1 You will see the configuration homepage under “ REPEATER ” mode now.
LAN Settings: This page displays the Broadband router LAN port’s current LAN information. WLAN Settings: Wireless configuration details such as SSID, Status(Connected/Disconnected), Security and Channel are briefly shown. - LAN The LAN Tabs shows LAN settings.
802.1d Spanning Tree: This is disabled by default. If 802.1d Spanning Tree function is enabled, this router will use the spanning tree protocol to prevent network loops.
- Event Log View operations log of the ENHWI-N3 . This page shows the current system log of the ENHWI-N3 router. It displays any event occurred after system start up.
- Language This Wireless Router supports multiple languages for user interface. Select your preferred language. Wireless - Basic You can set parameters use by the wireless stations to co nnect to this router. The parameter includes Mode, ESSID, Channel Number and Associated Client.
Radio: Enable or Disable Wireless function Band: Allows you to set the frequency band of the router. Fix at 802.11b, 802.11g or 802.11n modes. You can also select B+G mode to allow 802.11b and 802.11g clients at the same time. Enable ESSID: You can specify the maximum ESSI D number.
- Client List This WLAN Client Table shows the Wireless client associated to t his Wireless Router. - Policy The Broadband router allows you to set up the Wireless Access Policy. If multiple SSID is created, this is the place to set the policy for each SSID.
Communication between Wireless clients and wired clients: This function allows the Wireless Client to communicate with other Wireless Client in the LAN on specific SSID as well as the Wired Client connected to the switch portion of this router.
Old Password: Fill-in the current password to be replaced. This is required to allow changing to a new password. New Password: Enter your new password and again in Repeat New Password for verification.
NTP Time Server: Enter the NTP Time Server address or URL here. This also accepts local the IP address if the NT P Time Server is on the same LAN. Daylight Savings: The router can also setup to automatically adjust the Daylight Savings Time changes each time DST changes.
- Diagnosis This page lets you diagnose the connection problem and the network status by executing the Ping function. The result tells you whether the connection is broken or successful. - Firmware This page allows you to upgrade the router’s firmware.
The saved backup can be restored again if needed by sing the Restore Settings selection and browse the saved backup file to restore back to the expected settings. If restore is not an option the Restore to Factory Default may be the only way to recover the router from damage.
- Reset You can software reset the broadband router when system stops responding or stop working. This is different from the hardware reset that can reset th e settings by physically pressing the button.
z Connect the equipment into an outlet on a circui t different from that to which the receiver is connected. z Consult the dealer or an experienc ed radio/TV technician for help.
Een belangrijk punt na aankoop van elk apparaat ENCORE N150 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen ENCORE N150 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens ENCORE N150 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding ENCORE N150 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over ENCORE N150 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van ENCORE N150 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de ENCORE N150 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met ENCORE N150 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
