Gebruiksaanwijzing /service van het product ESR6670 van de fabrikant EnGenius
Ga naar pagina of 94
ESR6670 1 1N Wireless 3G Router (IEEE 802.1 1 b/g/n) User Manual.
T ABLE OF C ONTENTS 1. INTRODUCTION ................................................................................................................... ........................... 1 1.1. S UMMAR Y ......................................................
Revision History V ersion Date Notes 1.0 March 2, 2009 Initial.
1 1. Introduction 1.1. Summary Congratulations on your purchase of ESR6670 3G Wireless Router. ESR6670 is compatible with the most popular 3G standards and 802.
1.2. Key Features Features Advantages 3G Data Card Support Allows user to share 3G network among multiple users. It supports WCDMA (HSDPA), CDMA2000 and TD-SCDMA. Incredible Data Rate up to 300Mbps** Heavy data payloads such as MPEG video streaming IEEE 802.
3 1.3. Package Contents Open the package care fully , and make sure that none of the items listed below ar e missing. Do not discard the packing materials, in case of return; the unit must be shipped back in its original package. 1. SOHO Router 2. 100V or 240V Power Adapter 3.
4 1.4. Product Layout.
5 LED Description Power 1 ( On-> red T est/reset default->blink) 3G 1 ( Link-> green on, traffic->blink) W AN 1 ( Link-> blue on, traffic->blink) Internet 1 ( Link-> blue on, traf.
2. Installation 2.1. Network + System Requirement s T o begin using the ESR6670, make sure you meet the following as minimum requirements: PC/Notebook. Operating System – Microsoft Windows 98SE/ME/XP/2000/VIST A 1 Free Ethernet port. WiFi card/USB dongle (802.
2.3. Setup LAN & 3G (W AN) LAN connection: Connect Ethernet cable between your PC/Notebook LAN port & one of the 2 available LAN ports on ESR6670. 3G connection: Plug-in your 3G data card into USB port if you would like to access Internet through 3G network.
8 2.4. PC Network Adapter setup ( Windows XP ) Enter [Start Menu] select [Control panel] select [Network]. Select [Local Area Connection]) icon=>select [properties].
9 Select [Internet Protocol (TCP/IP)] =>Click [Properties]. Select the [General] tab. ESR6670 supports [DHCP] function, please select both [Obtain an IP address automatically] and [Obtain DNS server address automatically].
2.5. Bring up ESR6670 Connect the supplied power-adapt er to the power inlet port and connect it to a wall outlet. Then, ESR6670 automatic ally enters the self-test phase. During self-test phase, Power LED will blink briefly, and then wi ll be lit continuously to indicate that this product is in normal operation.
3. Smart Wizard Click <Next> to enter mode selection. Select the mode that ESR6670 is going to be and set its configurations. AP Repeater mode does not enable WAN interface, Setup Wizard will skip WAN Configuration. Click <Next> to automatically detect your Internet Network settings.
12 You could choose your service type or sele ct Others to setup WAN configurations manually. Smart Wizard has detected DHCP client. Configure the host name and MAC address of ESR6670. Click Next to proceed. Smart Wizard has finished setting up WAN Configuration .
13 Enter the name for your wireless network (SSID) and security key Click <Next> to proceed To apply the entire configuration, click <Reboot> . NOTE: After Wireless settings are applied, you need to connect from your WLAN client with the security settings you just finished configuring.
14 4. Initial Setup ESR6670 ESR6670 uses web-interface for configuration to be accessed through your web browser, such as Internet Explorer or Firefox. - LOGIN Procedure 1. OPEN your browser (e.g. Internet Explorer). 2. Type http://192.168.0.1 in address bar and hit [Enter] button on your keyboard.
15 3. Click <OK> to navigate into ESR6670 configuration home page. 4. You will see the home page of ESR6670 as follows..
5. AP Router Mode 5.1. System - S t atus This page allows you to monitor the current status of your router. System: You can see the Uptime, hardware information, serial number as well as fir mware version information. WAN Settings: This section displays whether the WAN port is connecte d to a Cable/DSL connection.
17 LAN Settings: This section displays the Router LAN port’s current information. It also shows whether the DHCP Server function is enabled / disabled.
18 LAN IP IP address: 192.168.0.1. It is the router’s LAN IP address (the “Default Gateway” IP address of your LAN clients). It can be changed based on your own choice. IP Subnet Mask: 255.255.255.0 Specify a Subnet Mask for your LAN segment. 802.
19 Start IP: This is the beginning of the IP pool for DHCP client hosts. End IP: . This is the end of the IP pool for DHCP client hosts Domain name: The Domain Name for the existing or customized network.
- DHCP View the current LAN clients which are assigned with an IP Address by the DHCP-server. This page shows all DHCP clients (LAN PCs) currently connected to your network. The table shows the assigned IP address, MAC address and expiration time for each DHCP leased client.
- Schedule This page allows users to set up schedule function for Firewall and Power Saving . Edit schedule options to allow configuration of f irewall and power savings services. Fill in the schedule and select type of service. Click < Apply > to keep the settings.
22 The schedule table lists the pre-sch edule service-runs. You can select any of the schedule record using the check box..
- Event Log View operation event log . This page shows the current system log of the Router. It displays any event occurred after system start up. At the bottom of the page, the system log can be save.
- Monitor Show histogram for network connection on WAN, LAN & WLAN. Auto refresh keeps information updated frequently. - Language This Wireless Router support multiple language of web pages, You could select your native language here.
25 5.2. Wizard Click Wizard to conf igure the Router. Setup wizard will now be displa yed; check that the modem is connected and click <Next>. The details please refer to Smart Wizard <Page 13>.
5.3. INTERNET - S t atus This page shows the current Internet connection type and status ESR6670 support s both 3G and ADSL for Internet access. Please note that 3G (USB interface) network by default is th e preferred Internet option.
- Dynamic IP Use the MAC address when registering for Internet service, and do not change it unless required by your ISP . If your ISP used the MAC address of the Ethernet card as an identifier , connect only the PC with the registered MAC address to the Router and click the <Cl one MAC Address> button.
- S tatic IP If your ISP Provider has assigned a fixed IP address, ent er the assigned IP addre ss, Subnet mask, Default Gateway IP address, and Primary DNS and Secondary DNS (if available) of your ISP provider .
- Point-to-Point over Ethernet Protocol (PPPoE) Login / Password: Enter the PPPoE username and password assigned by your ISP Provider . Service Name: This is normally optional. Maximum T ransmission Unit (MTU): This is the maximum size of the p ackets.
- Point-to-Point T unneling Protocol (PPTP) PPTP allows the secur e connection over the Internet by simply dialing in a local point provided by your ISP provider . The following screen allows client PCs to establish a normal PPTP session and provides hassle-f ree configuration of the PPTP client on each client PC.
- 3G Network ISP: It shows a list of supported 3G Network Internet Service Provider . APN Code: Enter APN if ISP requires it. Dial Number: Enter phone number if ISP requires it. User Name: Enter 3G network account / username Password: Enter 3G network account password T ype: Keep Connection: Keep connection with or without the presence of traf fic.
5.4. Wireless Settings - Basic In basic setting page, you can set wireless Radio, Mode, Band, SSID, and Channel. Radio: You can turn on/off wireless radio. If wireless Radio is off, you cannot associate with AP through wireless. Mode: In this device, we support three operation modes which are AP router and AP route with WDS .
33 ESSID1~4: ESSID is the name of your wireless network. It might be a unique name to identify this wireless device in the Wireless LAN. It is case sensitive and up to 32 printable characters.
- WDS with AP Router Wireless Distribution System, a system t hat enables the wireless interconnection of access point, allows a wireless network to be extended using multiple APs without a wired backbone to link them. Each WDS AP needs same channel and encryption type settings.
35 Fragment Threshold: This specifies the maximum size of a packet during the fragmentation of data to be transmitted. If you set this value too low, it will result in bad performance. RTS Threshold: When the packet size is smaller than the RTS threshold, the wireless router will not use the RTS/CTS mechanism to send this packet.
36 Data Rate: The “Data Rate” is the rate that this access point uses to transmit data packets. The access point will use the highest possible selected tr ansmission rate to transmit the data packets. N Data Rate: The “Data Rate” is th e rate that this access point uses to transmit data packets for N compliant wireless nodes.
- Security This Access Point provides complete wireless LAN security functions, in cluded are WEP, IEEE 802.1x, IEEE 802.1x with WEP, WPA with pre-shared key and WPA with RADIUS. With these security functions, you can prevent your wireless LAN from illegal access.
38 IEEE 802.1x is an authentication protocol. Every user must use a valid account to login to this Access Point before accessing t he wirele ss LAN. The authentication is processed by a RADIUS server. This mode only authenticates us ers by IEEE 802.1x, but it does not encrypt the data during communication.
39 Authentication Type: There are two authentication types: "Open System" and "Shared Key" . Both AP and wireless client must be configured with t he same authentication type. Key Length: You can select the WEP key length for encryption, 64-bit or 128-bit.
40 WP A-Radius Encryption Wi-Fi Protected Access ( WPA ) is an advanced security standard. You can use an e xternal RADIUS server to authenticate wireless stations and provide the session key to encrypt data during communication. It uses TKIP o r C C M P ( AES ) to change the encryption key frequently.
41 - MAC Address Filtering This wireless router supports MAC Address Control, which prevents unauthorized clients from accessing your wireless network.
42 WPS is the simplest way to establish a connection between the wireless clients and the wireless router. You don’t have to select the encryption mode and fill in a long encryption passphrase every time when you try to setup a wireless connection.
43 Authentication Mode: It shows the active authentication mode for the wireless conn ection. Passphrase Key: It shows the passphrase key that is randomly generated by the wireless router during the WPS process. You may need this information when using a device which doesn’t support WPS.
- Client List This WLAN Client Table shows the Wireless client associate to this Wir eless Router. - Policy The Router can allow you to set up the Wireless Access Policy.
5.5. Firewall Settings The Router provides extensive firewall protecti on by restricting connection parameters, thus limiting the risk of hacker attacks, and defendi ng against a wide array of common Internet attacks.
46 packets going to your WAN port IP address to a particular IP address in your LAN. The difference between the virtual server and the DMZ function is that the virtual server re-directs a particular service/Internet application (e.
- Denial of Service (DoS) The Router's firewall can block common hacker attacks, including Denial of Service, Ping of Death, Port Scan and Sync Flood. If Internet attacks occur the router can log the ev ents. Ping of Death: Protections from Ping of Death attack.
48 - MAC Filter If you want to restrict users from accessing certain Internet applications / services (e.g. Internet websites, email, FTP etc.), and then th is is the place to set that configuration. MAC Filter allows users to define the traffic type permitted in your LAN.
49 Add PC MAC Address Fill in “ LAN MAC Address ” and <Description> of the PC that is allowed / denied to access the Internet, and then click <Add> . If you find any typo before adding it an d want to retype again, just click <Reset> and the fields will be cleared.
50 - IP Filter Enable IP Filtering: Check to enable or uncheck to disable IP Filtering. Deny: If you select “ Deny ” then all clients will be allowed to access Internet except for the clients in the list below. Allow: If you select “ Allow ” then all clients will be denied to access Internet except for the PCs in the list below.
51 - URL Filter You can block access to some Web sites from particular PCs by entering a full URL address or just keywords of the Web site. Enable URL Blocking: Enable or disable URL Blocking Add URL Keyword Fill in “URL/Keyword” and then click <Add> .
52 Remove URL Keyword If you want to remove some URL keywords from the " Current URL Bl ocking Table ", select the URL keyword you want to remove in the table and then click <Delete Selected> . If you want remove all URL keywords from the table, click <Delete All> button.
53 5.6. Advanced Settings - Network Address T ranslation (NA T) Network Address Translation (NAT) allows multiple users at your local site to access the Internet through a single Public IP Address or multiple Public IP Addresses.
54 Enable Port Mapping: Enable or disable port mapping function. Description: description of this setting. Local IP: This is the local IP of the server behind the NAT firewall.
55 If you want to remove a Port Mapping setting from the " Current Port Mapping Table ", select the Port Mapping setting that you want to remove in the table and then click D<Delete Selected> . If you want to remove all Port Mapping settings from the table, click <Delete All> button.
56 Enable Port Forwarding: Enable or disable Port Forwarding. Description: The description of this setting. Local IP / Local Port: This is the LAN Client/Host IP address and Port number that the Public Port number packet will be sent to. Protocol: Select the port number protocol type (TCP, UDP or both).
57 - Port T riggering (Special Applications) Some applications require multiple connections, such as Internet games, video Conferencing, Internet telephony and others. In this section you can configure the router to support multiple connections for these types of applications.
58 selection. Once you have selected an applicatio n, select a location (1-5) in the “Add” selection box and then click the <Add> button. This will automatically list the Public Ports required for this popular application in the location (1-5) you specified.
59 - UPNP With UPnP, all PCs in you Intranet will discov er this router automatically. So, you don’t have to configure your PC and it can easily access the Internet through this router. Enable/Disable UPnP: You can enable or Disable the UPnP feature here.
- Quality of Service (QoS) QoS can let you classify Internet application traffic by source/destination IP address and port number. You can assign priority for each t ype of application and reserve bandwidth for it. The packets of applications with higher priority will always go first.
61 Unlimited Priority Queue: The LAN IP address will not be bounded in the QoS limitation. High/Low Priority Queue: This can put the p ackets in the protocol and port range to High/Low QoS Queue. Bandwidth Allocation: This can reserve / limit the throughput of specific protoco ls and port range.
62 Policy: S pecify the policy the QoS, Min option will reserve the selected data rate in QoS queue. Max option will limit the selected dat a rate in QoS queue.
- Routing Y ou can set enable S tatic Routing to let the router forward packet s by your routing policy . Destination LAN IP: S pecify the destination LAN IP address of st atic routing rule. Subnet Mask: S pecify the Subnet Mask of static routing rule.
5.7. T OOLS Settings - Admin You can change the password required to log into the Router's system web-based management. By default, the password is: adm in. Passwords can contain 0 to 12 alphanumeric characters, and are case sensitive. Old Password: Fill in the current password to allow changing to a new password.
65 Remote managemen t This allows you to designate a host in the Internet the ability to configure the Router from a remote site. Enter the designated host IP Address in the Host IP Address field. Host Address: This is the IP address of the host in the Inte rnet that will have management/configuration access to the Router from a remote site.
66 - T ime The Time Zone allows your router to reference or base its time on the settings configured here, which will affect functions such as Log entri es and Firewall settings. Time Setup: Synchronize with the NTP server Time Zone: Select the time zone of the country you are currently in.
67 PC Date and Time: This field would display the PC date and time. Daylight Savings: The router can also take Daylight Savings into account. If you wish to use this function, you must select the Daylight Savings Time period an d check/tick the enable box to enable your daylight saving configuration.
- DDNS DDNS allows you to map the static domain nam e to a dynamic IP address. You must get an account, password and your static domain nam e from the DDNS service providers.
- Power Saving power in WLAN mode can be enabled / disabled in this page. - Diagnosis This page could let you diagnosis your current network status..
- Firmware This page allows you to upgrade the router’s firmware. To upgrade the firmware of your Router, you need to download the firmware file to your local hard d isk, and enter that file name and path in the appropriate field on this page. You can also use the Browse button to find the firmware file on your PC.
- Back-up This page allows you to save the current router configurations. When you save the configurations, you also can re-load the saved configuration s into the router through the Restore Settings . If extreme problems occur you can use the Restore to Factory Defaults to set all configurations to its original default settings.
- Reset You can reset the Router when system stops responding correctly or stop functions..
73 6. Repeater Mode Repeater mode has limited settings compared to the AP mode. Choose “Repeater mode” on the top right corner of the configuration page. System restarts and connects to the IP address http://192.168..0.1 You will see the configuration homepage under “ REPEATER ” mode now.
6.1. System - Status System status section allows you to monitor the current status of your router. You can see the Uptime, hardware information, serial number as well as firmware version information. LAN Settings: This page displays the Router LAN port’s current LAN & WLAN information.
75 IP address: It is the router’s LAN IP address (Your LAN clients default gateway IP address). It can be changed based on your own choice. IP Subnet Mask: Specify a Subnet Mask for your LAN segment. 802.1d Spanning Tree: This is disabled by default.
76 The schedule table lists the pre-schedule service-r uns. You can select an y of them using the check box..
77 - Event Log View operation log of ESR6670 . This page shows the current system log of the Router. It displays any event occurred after system start up.
78 - Monitor Show the network packets histogram for network connection on WAN, LAN & WLAN. Auto refresh keeps information updated frequently. - Language This Wireless Router support multiple language of web pages, you could select your native language here.
6.2. Wireless -Basic You can set parameters that are used for the wireless stations to connect to this router. The parameters include Mode, ESSID, Channel Number and Associated Client. Radio: Enable or Disable Wireless function Band: Allows you to set the AP fixed at 802.
80 -Client List This WLAN Client Table shows the Wireless client associate to this Wir eless Router..
81 -Policy The Router can allow you to set up the Wireless Access Policy. Communication between Wireless clients: Allow Wireless Client to communicate with other Wireless Client on specific SSID.
6.3. T ools - Admin You can change the password required to log into the Router's system web-based management. By default, the password is: adm in. Passwords can contain 0 to 12 alphanumeric characters, and are case sensitive. Old Password: Fill in the current password to allow changing to a new password.
83 Remote managemen t This allows you to designate a host in the Internet the ability to configure the Router from a remote site. Enter the designated host IP Address in the Host IP Address field. Host Address: This is the IP address of the host in the Inte rnet that will have management/configuration access to the Router from a remote site.
84 - T ime The Time Zone allows your router to reference or base its time on the settings configured here, which will affect functions such as Event Log entries an d Schedule settings. Time Setup: Synchronize with the NTP server Time Zone: Select the time zone of the country you are currently in.
85 PC Date and Time: This field would display the PC date and time. Daylight Savings: The router can also take Daylight Savings into account. If you wish to use this function, you must select the Daylight Savings Time period and check/tick the enable box to enable your daylight saving configuration.
86 - Power Saving power in WLAN mode can be enabled / disabled in this page. - Diagnosis This page could let you diagnosis your current network status.
87 - Firmware This page allows you to upgrade the router’s firmware. To upgrade the firmware of your Router, you need to download the firmware file to your local hard disk, and enter that file name and path in the appropriate field on this page. You can also use the Browse button to find the firmware file on your PC.
88 - Back-up The page allows you to save (Backup) the router’s current configuration settings. When you save the configuration setting (Backup) you can re-load the saved configuration into the router through the Restore selection .
89 - Reset You can reset the Router when system stops responding correctly or stop functions..
90 Appendix A – FCC Interference Statement Federal Communication Commission Interference St atement This equipment has been tested and found to comply with t he limits for a Class B digit al device, pursua nt to Part 15 of the FCC Rules.
Appendix B – IC Interference Statement Industry Canada st at ement: This device complies with RSS-210 of the In dustry Canada Rules. Operation is subject to the following two conditions: (1) This de.
Een belangrijk punt na aankoop van elk apparaat EnGenius ESR6670 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen EnGenius ESR6670 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens EnGenius ESR6670 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding EnGenius ESR6670 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over EnGenius ESR6670 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van EnGenius ESR6670 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de EnGenius ESR6670 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met EnGenius ESR6670 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
