Gebruiksaanwijzing /service van het product TM-P60 van de fabrikant Epson
Ga naar pagina of 148
TM-P60 with Peeler Technical Reference Guide EPSON English 410383801 Rev. B.
.
i TM-P60 with Peeler Technical Reference Guide CAUTIONS ❏ This document shall apply only to the product(s) id entified herei n. ❏ No part of this document may be repr oduced, stored in a retrie v .
ii The influence on the environment of radio wave radiation ❏ The Radio Frequency module that can be instal led in this product radiates the same high frequency energy as some other high frequency d.
iii TM-P60 with Peeler Technical Reference Guide • Confirm that radio and other broadca sting equipment are n ot used nearb y before using this product. • When trouble occurs, for example, if the Ra dio Frequency module causes problems such as radio wave interference, con sult your dealer.
iv Seiko Epson Corporation suggests that the secu rity setting is set by the judgment and the responsibility of user after understanding the possible problems resulting from using this product without the security settings. For details, see “Wireless LAN Security” in Appendix B.
v TM-P60 with Peeler Technical Reference Guide Revision Information Revision Page Altered Items and Contents Rev. A All pages Newly authorized Rev. B vii “Restriction of Use” added “Downloading .
vi About This Manual Aim of the Manual This manual was created to provide specific info rmation on the TM-P60 with Peeler printer for anyone who is developing hardware, installation s, or programs. See also materials provided for the TM-P60 described in “Restri ction of Use” on page vii.
vii TM-P60 with Peeler Technical Reference Guide Restriction of Use When this product is used for applications requiring high reliability/safety such as transportation devices related to aviation, rail, marine, automotive etc.
viii.
ix TM-P60 with Peeler Technical Reference Guide Safety Precautions EMC and Safety Standards Applied Product Name: TM-P60 with Peeler Model Name: M196C The following standards are appli ed only to the printers that are so labeled. (EMC is tested using the EPSON power supplies.
x CE Marking DECLARATION of CONFORMITY According to ISO/IEC Guide 22 and EN 45014 Manufacturer: SEIKO EPSON CORPORA TION Address: 3-5, Owa 3- chome, Suwa-shi, Nagano-ken 392-8 502 JAPAN Representative: EPSON Engineering Europe S.
xi TM-P60 with Peeler Technical Reference Guide RF Module This equipment contains the following wireless modul e. Manufacturer: TOYOTA INDUSTRIE S CORPORATION Model Name: 6180 210 Product Name: WIRELESS LAN CF-CARD This device complies wit h Part 15 of the FCC Rules and RSS- 2 10 of the IC Rules.
xii EUROPE Hereby, TOYOT A INDUSTRIES CORPORA TION, declares th at this 6180210 is in compli ance with the essential requirements and other relevant provisio ns of Directive 1999/5/EC and 89/ 336/EEC. France In France, using the TM-P60 with Peeler outdoors is prohibited.
xiii TM-P60 with Peeler Technical Reference Guide S afety Precautions This section presents important information to ensure safe and effective use of this product. Please read this section carefully and store it in an accessible location. WARNING: ❏ Shut down your equipment i mmediately if it produces smoke, a strange odor, or unusual noise.
xiv CAUTION: ❏ Do not connect cables other than as described in this manual. Different connections may cause equipment damage and burning. ❏ Be sure to set this equipment on a firm, stable, horizo ntal surface. Product may break or caus e injury if it falls.
xv TM-P60 with Peeler Technical Reference Guide Contents TM-P60 with Peeler Technical Reference Guide The influence on the environment of ra dio wave radiatio n . . . . . . . . . . . . . . . . . . . . . . . . . . . ii Note about interference . . . . .
xvi Installing the Roll Paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6 Install the Battery Pack or Connect the Printer to the AC adapter . . . . . . . . . . . . . . .
xvii TM-P60 with Peeler Technical Reference Guide OPOS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8 ESC/POS command . . . . . . . . . . . . . . . . .
xviii The TM-P60 with Peeler can’t connect to the Wireles s LAN. What should I do? . . . . . . . . . . . E-2 Wireless LAN parameters for the TM-P60 with Peeler cannot be set with RS-232 . . . . . . . . . . E-3 Searching on the network takes several min utes.
Rev. B General Information 1-1 TM-P60 with Peeler Technical Reference Guide Chapter 1 General Information 1.1 Features The TM-P60 with Peeler is a mobile l abel printer designed to meet the needs of retail, grocery stores, DIYs, and speciality chain stores for in-s tore printing of items such as shelf labels, discount labels, and product tags.
1-2 General In formation Rev. B 1.2 System Construction Image On-demand printing for shelf labels, product tags , or discount labels using a 802.11b wire less LAN.
Rev. B General Information 1-3 TM-P60 with Peeler Technical Reference Guide 1.3 Product Structure 1.3.1 Standard Parts Included with the Printer This printer is packed with the materials listed below.
1-4 General In formation Rev. B 1.3.2 Related materials for the TM-P60 with Peeler In addition to this guide, the following material s are provided for the TM-P60 with Peeler. See also the following materials. Please contact your dealer to get these. 1.
Rev. B General Information 1-5 TM-P60 with Peeler Technical Reference Guide 1.5 Product Specifications Overview Print method Thermal line printing Print density 203 dpi × 203 dpi [dpi: dots pe r 25.
1-6 General In formation Rev. B.
Rev. B 2-1 Setup TM-P60 with Peeler Technical Reference Guide Chapter 2 Setup Part Name and Basic Operation Part names battery cover roll pape r cover open button connector for AC adapter (option) bel.
2-2 Setup Rev. B Control Panel The control panel is shown below. ❏ POWER LED ❏ ERROR LED ❏ BATT. LED ❏ POWER button ❏ FEED button POWER LED POWER button FEED button ERROR LED BATT.
Rev. B 2-3 Setup TM-P60 with Peeler Technical Reference Guide LED POWER ERROR BATT. Control Panel Buttons The control panel has a FEED button that you ma y have to use, although most paper handling functions will be handled by your software. POWER Press the button to turn the power on or off.
2-4 Setup Rev. B Beeper Function This printer has a “beeper“ function. This functi on causes beeping in specified situations. The situations are the following: ❏ The battery remaining is low (Memory switch can enable/disable this function) ❏ The printer can’t find any Access point (wirel ess LAN).
Rev. B 2-5 Setup TM-P60 with Peeler Technical Reference Guide S etup Flow You have to se t up your printer to use it. An d you can adjust some fe atures by customizing them. This section describes the setup. The setup flow of preparing to use printer is below.
2-6 Setup Rev. B Switching Issuing Mode The issuing mode can be switched between the label continuous issuing mode and the labe l peeler issuing mode by folding th e peeler holder under the pe eler cover. Installing t he Roll Pape r CAUTION: Be sure to use roll paper that meets the specifications.
Rev. B 2-7 Setup TM-P60 with Peeler Technical Reference Guide 3. When installing the label paper horizontally: Set the new roll paper on the inside of the roll pape r cover and pull the leading edge of the roll paper. When installing the label paper vertically: Set the new roll paper in the inside of the roll paper cover.
2-8 Setup Rev. B 5. Close the peeler holder. Note: Removing the issued label enables th e label peeler detector to detect a PAPER END and the printer to issue the next label.
Rev. B 2-9 Setup TM-P60 with Peeler Technical Reference Guide Install the Battery Pack or Conne ct the Printer to the AC adapter You can supply power through the battery pack packaged with th e printer or the AC adapter PS-10 provided as an option. WARNING: Be sure to use the battery LIP-2500 that came with the printer.
2-10 Setup Rev. B A djusting Various Settings This printer is able to be adjusted for the items below: ❏ DIP switch (handshake of seri al communication conditions) ❏ Memory switch (status notice tran smission and buzzer conditions) ❏ Roll paper width Note: When you adjust these items, we recommend you to confirm the new setting.
Rev. B 2-11 Setup TM-P60 with Peeler Technical Reference Guide Memory Switches This printer has a set of software switches ca lled “Memory switches.“ The memory switch set has “Msw 8,” “Customiz e value,” “Serial communication condition.
2-12 Setup Rev. B * “Time for auto power off”: When a printer isn’t received any data from host PC, and isn’t operated anything (ex. opening the ro ll paper cover, pressing th e FEED butt on) durin g the specif ie d time, the printer turns off itself automatically.
Rev. B 2-13 Setup TM-P60 with Peeler Technical Reference Guide Belt Clip You can hang the printer on your be lt using the bel t clip attached to the back of the printer. If you want to hang the printer on your neck, you can use the neck strap provided as an option.
2-14 Setup Rev. B Installing your wireless LAN This section describes how to install a wireless LA N in this printer. The following shows you the installation procedure. Note: For detailed information about the ut ility and web browser for LAN setting, see “Wireless LAN Setup Detailed Information” on page A- 1.
Rev. B 2-15 Setup TM-P60 with Peeler Technical Reference Guide Preparing a host PC for setting up a printer At first, prepare a PC (trial host PC) to set up a printer. The requirements for the trial host PC are the following: ❏ OS: Windows 2 000 professiona l, Windows XP professional ❏ Communication port: 80 2.
2-16 Setup Rev. B Adjusting the host PC to the printer’s LAN setting When you set up the printer with serial interface, omit this section and read from “Connecting a serial interface cable” on page 2- 16. Adjust the LAN setting of the host PC correspon ding to the status sheet.
Rev. B 2-17 Setup TM-P60 with Peeler Technical Reference Guide 3. Connect the serial interface cable (optio n) to the printer and the serial port of the host PC. 4. Turn on the printer while pressing the FEED button. 5. The printer prints the self test result, which is necessary for the next step.
2-18 Setup Rev. B 3. Confirm the printer is shown in the list view. Note: If the printer isn’t shown in the list view, check fo llowi ng item. See Appendix A for details of the utility function.
Rev. B 2-19 Setup TM-P60 with Peeler Technical Reference Guide “Search Path“; Menu:Tool -> “Search Me thod.“ (You should check “Search Path selection: select All“) “Search Option COM“; Menu:Tool -> “Search O ption” -> “COM.
2-20 Setup Rev. B 4. When following screen is shown, the confirmation is complete. Adjusting the printer LAN setting for your wireless LAN When you use the utility (TMNetWinConfig) to set up In this step, change the LAN setting of printer to the setting of the wireless LAN installed in the printer from the trial host PC.
Rev. B 2-21 Setup TM-P60 with Peeler Technical Reference Guide 3. Click the “Wireless“ Tab 4. Set following items for the wireless LAN installed the printer.
2-22 Setup Rev. B 6. Set the following items for the wireless LAN installed in the printer. • Method for specifying the IP address • IP address setting (IP addr ess, Subnet Mask, Default gateway) When you select the method “Auto,“ you can omit the IP address setting.
Rev. B 2-23 Setup TM-P60 with Peeler Technical Reference Guide 2. Click “Wireless“ from the right side menu. 3. Set the following items for the wireless LAN installed in the printer.
2-24 Setup Rev. B 6. Set the following items for the wireless LAN installed the printer. • Get IP Address • Set using Automatic Private IP Addressing (APIPA) •S e t u s i n g P I N G • IP Address setting (IP address, Subnet Mask, Default Gateway) When you select the method “Get IP Address: Auto,“ you can omit the IP address setting.
Rev. B 2-25 Setup TM-P60 with Peeler Technical Reference Guide Outline of install and setup procedure is as foll ows. ST AR T 1. Installation OPOS ADK (Ex ecute the Setup .e x e in DISK1, and continue to installation b y wizard) Is installation completed? 2.
2-26 Setup Rev. B 2.2. Device communication test b y e x ecuting the CheckHealth ResultCode SUCCESS ERROR Confirm the error condition by ref erring to the [User's manual] END The OPOS and de vice settings are r ight. & The Install and Setup are completed.
Rev. B 2-27 Setup TM-P60 with Peeler Technical Reference Guide 1. Installation. Execute the Setup.exe in DISK. and continue to install by following the wizard instructions. 2. Set up the device and environment. 1. Set the device setting by using SetupPOS utility.
2-28 Setup Rev. B Advanced Printer Driver (APD) Installing and Setting Up When you install and set up the APD, please refer to the “EPSON Advanced Printer Driver Install Manual.“ The Manual is a PDF file, wh ich is provided with other manuals for the APD.
Rev. B Troubleshooting 3-1 TM-P60 with Peeler Technical Reference Guide Chapter 3 Troubleshooting This section describes general troubleshoot ing. 3.1 LED Blinking Pattern 3.1.1 Error Types The printer stops all printer ope rations, goes offline, and the ERROR LED blinks when an error is detected.
3-2 Troubleshooting Rev. B Note: The ERROR LED is on when the printer is offl ine (p aper out, power-on initializ ation, roll paper cover open, power-off operation, or the rem aining battery charge is not enou gh for printer operation when the battery is used to supply the powe r.
Rev. B Troubleshooting 3-3 TM-P60 with Peeler Technical Reference Guide 3.3 Printer Beeps When the Power is Turned on When printer can’t find any access points with the current wireless LAN setting, the printer beeps to warn you. [See “Printer Bee ps” (page 3-2) for the bee ping pattern.
3-4 Troubleshooting Rev. B 2. While holding down the FEED button, tu rn on the pr inter using t he switch on the front of the printer. Continue to hold the FEED button until the ERROR LED comes on. The self test prints the printer settings and then prints the following, cuts th e paper, and pauses.
Rev. B Troubleshooting 3-5 TM-P60 with Peeler Technical Reference Guide 3.6 R adio Field Intensity Check Mode This mode prints the current radio fi eld intensity on roll paper. This mode is useful to confirm that the printer can co mmunicate with an acce ss point at the current location by radio.
3-6 Troubleshooting Rev. B 3.7 H exadecimal Dump Mode This feature allows experienced users to see exactl y what data is coming to the printer. This can be useful in finding software problems.
Rev. B Troubleshooting 3-7 TM-P60 with Peeler Technical Reference Guide 3.8 Cleaning the Thermal Head CAUTION: After printing, the thermal head can be very ho t. Be careful not to touch it and to let it cool before you clean it. Do not damage th e thermal head by touching it with your fingers or any hard object.
3-8 Troubleshooting Rev. B 3. Blow the paper dust accumulated around the ro ll paper end sensor with a blower or a straw. CAUTION: Do not wipe the roll paper end sensor with water or alcohol. Its functional capabilities may be affected. 4. Clos e the roll paper cover after the water or alcohol has dried.
Rev. B Application Development Information 4-1 TM-P60 with Peeler Technical Reference Guide Chapter 4 Application Development Information This section contains usable information to develop POS systems that use this printer. 4.1 About wireless communication 4.
4-2 Application Development Information Rev. B 4.1.3 Operation tested Access point products The Access points that have been evaluated with the TM-P60 with Peeler are in the following table.. 4.2 A bout the Battery Remaining Amount 4.2.1 The battery remaining amount This printer has a battery to supply power.
Rev. B Application Development Information 4-3 TM-P60 with Peeler Technical Reference Guide 4.2.2.2 Advanced Pr inter Driver The battery status can be confirme d by the S tatus API. The API is BiGetBatteryStatus . Also, the battery status can be transmitted wh en the status changes.
4-4 Application Development Information Rev. B 1. Open the properties of printer. 2. Click the “utility“ tab. 3. Click the “EPSON Control FontA“ button. 4. Click the “operation“ tab. 5. Edit a control font. The following table shows example definitions.
Rev. B Application Development Information 4-5 TM-P60 with Peeler Technical Reference Guide ❏ When an error status is sent to the host PC , the host PC can display an error message or solution message fo r operator (with beeping).
4-6 Application Development Information Rev. B When the FlagWhenIdle property is set to TRUE, PTR_SUE_IDLE is sent to inform the application that the printer is idle. Other than when data is being sent, the printer is in an idle state, so if FlagWhenIdle is TRUE, an e vent will be fired when prin ting is finished.
Rev. B Application Development Information 4-7 TM-P60 with Peeler Technical Reference Guide After an error occurs, more detailed informat ion about the error can be obtained from the ErrorLevel, ErrorStation, and ErrorString properties.
4-8 Application Development Information Rev. B 4.6 NV Graphics P rinting This printer has an “NV Bit-Graphics“ Function. Th is function provides printing Graphics (e.g. a shop logo.) This function is available for any control method (APD, OPOS, ESC/POS command.
Rev. B Application Development Information 4-9 TM-P60 with Peeler Technical Reference Guide 4.6.2.1 Printing method Print stored bitmap by DirectIO method.
4-10 Application Development Information Rev. B 4.6.2.4 Printable bitmap format in OPOS The printable bitmap formats are formats that meet all the follow ing conditions. ❏ BMP files ❏ Monochrome, 16-color (4 bit), 256-color (8 bit) ❏ Uncompressed 4.
Rev. B Wireless LAN Setup Deta iled Information A-1 TM-P60 with Peeler Technical Reference Guide Appendix A Wireless LAN Setup Detailed Information This appendix describes setting methods for wireless LAN. There are two method s: using TMNetWinConfig (utility software), and using yo ur we b browser.
A-2 Wireless LAN Setup Detailed Information Rev. B 2. Click Properties and check whether the Internet Protocol (TCP/IP) check box is checked. If not, click the check box. Note: After the TCP/IP is installed, restart your comp uter and move on to the Installing TMNetWinConf ig section.
Rev. B Wireless LAN Setup Deta iled Information A-3 TM-P60 with Peeler Technical Reference Guide 2. Double-click the Lo cal Area Connection icon. The Local Area Connection Status dialog is displayed. 3. Click Properties and check whether the Internet Protocol (TCP/IP) check bo x is checked.
A-4 Wireless LAN Setup Detailed Information Rev. B A.2 TMNetWinConfig This section describes the details of the TMNe tWinConfig, which is a utility for setting up a wireless LAN environment. A.2.1 Install Note: After TMNetWinConfig is installed, if you add or remove protocols or services, TMNetWinConfig might not work correctly.
Rev. B Wireless LAN Setup Deta iled Information A-5 TM-P60 with Peeler Technical Reference Guide 4. The License Agreement dialog is displayed . After confirming the contents, Click Yes . 5. The Choose Destination Location dialog is displayed. Select the folder for installati on and click Next .
A-6 Wireless LAN Setup Detailed Information Rev. B 6. The Select Program Folder dialog is displayed. Select the program folder for installation and click Next . The default is “Epson TMNetWinConfig.” 7. When the installation is finished, click Finish .
Rev. B Wireless LAN Setup Deta iled Information A-7 TM-P60 with Peeler Technical Reference Guide 3. The Welcome dialog is displayed. Click Next . 4. The License Agreement dialog is displayed .
A-8 Wireless LAN Setup Detailed Information Rev. B 5. The Choose Destination Location dialog is dis played. Select the folder for installation and click Next . The default is “C:Program File sEpsonNetEpsonTMNetWinConfig.” 6. The Select Program Folder dialog is displayed.
Rev. B Wireless LAN Setup Deta iled Information A-9 TM-P60 with Peeler Technical Reference Guide 7. When the installation is finished, click Finish . A.2.2 Operating CAUTION: Be sure not to turn off the prin ter or send printing data to t he printer while setting.
A-10 Wireless LAN Setup Detailed Information Rev. B 3. Click the printer for which you want to set the IP address, and then click the Configuration button. (You might have to wait for 10 seconds or more to view the TM-P60 with Peeler over the network on your screen.
Rev. B Wireless LAN Setup Detailed Information A-11 TM-P60 with Peeler Technical Reference Guide 4. Click the TCP/IP tab. Under Method for specifying the IP address , select one of the following: Automatic, or Manual . Note: To use “Method for specifying th e IP address: Auto,” a server for DHCP is necessary.
A-12 Wireless LAN Setup Detailed Information Rev. B CAUTION: Be sure that the Set using PING box is turned on if a setting by PING or ARP command is permitted. 6. Click the OK button. 7. Click the OK button again to be sure. 8. Enter the password set in the print server; then click OK .
Rev. B Wireless LAN Setup Detailed Information A-13 TM-P60 with Peeler Technical Reference Guide 10. When the message “Transmissio n is complete” appears, click OK . Note: To get the information for the TM-P60 with Peeler for the other segments, see the Functions section below.
A-14 Wireless LAN Setup Detailed Information Rev. B A.2.3 Functions This section describes the functions, includin g options, of the TMNetWinConfig. The main dialog box is shown below. . Note: The “Launch Browser“ funtion requi res Internet Explorer 4.
Rev. B Wireless LAN Setup Detailed Information A-15 TM-P60 with Peeler Technical Reference Guide A.2.3.1 Menu Bar This table shows each item and its function. (*) When you use this function, Wi ndows printing cannot be done while opening the TMNetWinConfig.
A-16 Wireless LAN Setup Detailed Information Rev. B Search Method Set the Search path. Note: When you use check “Select All“ or “COM,“ Wi ndows pri nting cannot be done while opening the TMNetWinConfig. You should use this option at only if you connect th e TM-P60 with Peeler with an RS-232C cable to your PC.
Rev. B Wireless LAN Setup Detailed Information A-17 TM-P60 with Peeler Technical Reference Guide Search Options - IP This function is to search for print serve rs in other segments. Set the network address and the subnet mask. Select Refresh from the View menu or restart TMNet WinConfig to activate the settings.
A-18 Wireless LAN Setup Detailed Information Rev. B Search Options - COM Specify the Searching COM port to match a TM-P60 with Peeler conne cted by an RS-232C cable.
Rev. B Wireless LAN Setup Detailed Information A-19 TM-P60 with Peeler Technical Reference Guide Firmware Update When you select this menu, the Firmware Update wizard starts up. Usually you don’t need to use this function. Help Topics Help for the TMNetWinConfig is displayed.
A-20 Wireless LAN Setup Detailed Information Rev. B About TMNetWinConfig The version information of the TMNetWinConfig is displayed. When clicking the mouse on the left in the dialog or pressing the [Enter] key or [ESC] key, the dialog is closed. A.2.
Rev. B Wireless LAN Setup Detailed Information A-21 TM-P60 with Peeler Technical Reference Guide Information Click the Information tab and dial og below is displayed. You can confirm the current setting of the TM-P60 with Peeler. ❏ Network-Card Information Information about the Netw ork-Card is displayed.
A-22 Wireless LAN Setup Detailed Information Rev. B ❏ Path Information Information about Network Card is displayed. ❏ Wireless Information Information about Wireless communication is displayed. • Refresh button The Wireless Information is upd ated with the latest information.
Rev. B Wireless LAN Setup Detailed Information A-23 TM-P60 with Peeler Technical Reference Guide Wireless Click the Wireless tab and the dialog below is dis played. Set the setting of the Communication Mode, SSID, and WEP. When you click the OK button, the host PC transm its the specified se ttings to the TM-P60 with Peeler.
A-24 Wireless LAN Setup Detailed Information Rev. B ❏ Using a WEP key When using the WEP Key, check the checkbox and set the following item Note: When clicking the “Use WEP Key” checkbox, W EP comes on and Authentication Method of Advanced Settings is set to “Shared Key” automatically.
Rev. B Wireless LAN Setup Detailed Information A-25 TM-P60 with Peeler Technical Reference Guide ❏ Advanced Settings button The Wireless Advanced Settings dial o g is displayed; set the following detailed items.
A-26 Wireless LAN Setup Detailed Information Rev. B ❏ RTS/CTS Threshold Setting ❏ Roaming Setting ❏ Fragment Threshold Setting TCP/IP Click the TCP/IP tab; the dialog be low is displayed. Set the TCP/IP. Item Explanation Set RTS/CTS handshake control Select RTS/CTS handshake co ntrol Disabl e or Enable.
Rev. B Wireless LAN Setup Detailed Information A-27 TM-P60 with Peeler Technical Reference Guide ❏ Method for specifying the IP address ❏ IP Address Setting Note: When using “Automatic” method , these items are disabled. ❏ Extended Settings button This button is disabled.
A-28 Wireless LAN Setup Detailed Information Rev. B A.3 Setting Using a Web Browser The TM-P60 with Peeler has a function to chan ge settings from a PC on which TMNetWinConfig isn't installed by using a browser such as Intern et Explorer. Note: Be sure to use Microsoft Internet Explorer 5.
Rev. B Wireless LAN Setup Detailed Information A-29 TM-P60 with Peeler Technical Reference Guide 4. You can modify the parameters by fo llowing the menus. You must click Submit to send the change to the printer and then click Reset to make the submission effective on each Web page.
A-30 Wireless LAN Setup Detailed Information Rev. B A.3.2 Function A.3.2.1 Informa tion General Click General, following screen is displayed. Yo u can confirm the basic se tt ings of the TM-P60 with Peeler. ❏ Interface Card Information of the Interface Card is displayed.
Rev. B Wireless LAN Setup Detailed Information A-31 TM-P60 with Peeler Technical Reference Guide ❏ Wireless Information Information about the Wireless communication is displ ayed. ❏ Printer Information about the printer is displayed. ❏ Refresh button It updates the information wi th the latest information.
A-32 Wireless LAN Setup Detailed Information Rev. B TCP/IP Click TCP/IP; the screen below is displayed. You can confirm the present setting of the TCP/IP. ❏ TCP/IP Information Item Explanation Get IP Address The setting co ndition of the IP Address setting method is displayed.
Rev. B Wireless LAN Setup Detailed Information A-33 TM-P60 with Peeler Technical Reference Guide SNMP Click SNMP; the screen below is displayed. Yo u can confirm the present setting of the SNMP.
A-34 Wireless LAN Setup Detailed Information Rev. B Wireless Click Wireless; the screen below is displ ayed. Set the Network Mode, SSID, and WEP. ❏ Wireless Basic Setting Set the basic se tting of the Wireless communication.
Rev. B Wireless LAN Setup Detailed Information A-35 TM-P60 with Peeler Technical Reference Guide ❏ Wireless Detail Setting • SUBMIT button Click this button after changing the setting contents to send the setting contents to the TM-P60 with Peeler.
A-36 Wireless LAN Setup Detailed Information Rev. B TCP/IP Click the TCP/IP, the screen below is displayed. Set the TCP/IP. ❏ TCP/IP Setting • SUBMIT button Click this button after changing the setti ng cont ents to send the setting contents to the TM-P60 with Peeler.
Rev. B Wireless LAN Setup Detailed Information A-37 TM-P60 with Peeler Technical Reference Guide SNMP Community Click Community; th e screen below is displayed. Set the SNMP Communication. ❏ Community • SUBMIT button Click this button after changing the setting contents to send the setting contents to the TM-P60 with Peeler.
A-38 Wireless LAN Setup Detailed Information Rev. B IP Trap 1, IP Tr ap 2 Click IP Trap 1 or IP Trap 2; the sc re en below is displayed. Set the administrator. ❏ SNMP IP Trap Setting • SUBMIT button Click this button after changing the setting contents to send the setting contents to the TM-P60 with Peeler.
Rev. B Wireless LAN Setup Detailed Information A-39 TM-P60 with Peeler Technical Reference Guide Administrator Click Administrator; the screen belo w is displayed.
A-40 Wireless LAN Setup Detailed Information Rev. B Password Click Password; the screen below is displayed. Set the Password. ❏ Password Setting • SUBMIT button Click this button after changing the setting contents to send the setting contents to the TM-P60 with Peeler.
Rev. B Wireless LAN Setup Detailed Information A-41 TM-P60 with Peeler Technical Reference Guide Reset Click Reset; the screen below is displayed. Reset th e setting of the TM-P60 with Peeler to the first condition. ❏ Reset • Reset button When you click this button, the TM-P60 with Peeler applies the changing and reboots itself.
A-42 Wireless LAN Setup Detailed Information Rev. B.
Rev. B Wireless LAN Network Composition B-1 TM-P60 with Peeler Technical Reference Guide Appendix B Wireless LAN Network Composition B.1 Network mode B.1.1 Infrastructure Mode This is a method for connecting to an existing wi red network using an access point.
Wireless LAN Network Composition B-2 Rev. B B.3 Wireless LAN Security B.3.1 Security of a wireless LAN Why does a wireless LAN need a security function? A wireless LAN is designed to be constructed ea.
Rev. B Wireless LAN Network Composition B-3 TM-P60 with Peeler Technical Reference Guide WEP Setting WEP is the function to encrypt the wireless data .
Wireless LAN Network Composition B-4 Rev. B.
Rev. B Character Code Tables C-1 TM-P60 with Peeler Technical Reference Guide Appendix C Character Code Tables C.1 Page 0 (PC437: USA, Standard Europe) (International character set).
C-2 Character Code Tables Rev. B C.2 Page 1 (Katakana).
Rev. B Character Code Tables C-3 TM-P60 with Peeler Technical Reference Guide C.3 Page 2 ( PC850: Multilingual).
C-4 Character Code Tables Rev. B C.4 Page 3 ( PC860: Portuguese).
Rev. B Character Code Tables C-5 TM-P60 with Peeler Technical Reference Guide C.5 Page 4 ( PC863: Canadian-French).
C-6 Character Code Tables Rev. B C.6 Page 5 ( PC865: Nordic).
Rev. B Character Code Tables C-7 TM-P60 with Peeler Technical Reference Guide C.7 Page 16 ( WPC1252).
C-8 Character Code Tables Rev. B C.8 Page 17 ( PC866: Cyrillic #2).
Rev. B Character Code Tables C-9 TM-P60 with Peeler Technical Reference Guide C.9 Page 18 ( PC852: Latin2).
C-10 Character Code Tables Rev. B C.10 Page 19 ( PC858: Euro).
Rev. B Character Code Tables C-11 TM-P60 with Peeler Technical Reference Guide C.11 P age 255 (Blank page).
C-12 Character Code Tables Rev. B C.12 International Character Set s ASCII code (hexadecimal number) Germany Country U.S. France UK Denmark I Sweden Italy Spain I Japan Norway Denmark II Spain II Lati.
Rev. B System Planning D-1 TM-P60 with Peeler Technical Reference Guide Appendix D System Planning This section provides you information for system planning. D.1 Control Method A TM printer can print and be controlled using any of the following three methods: 1.
D-2 System Planning Rev. B EPSON Advanced Printer Driver Components Installer recognizes PC environment in which the installation will be done and installs DLL files and software components necessary for operating automatically. Drivers, sample programs, or manuals are provided in separate exe files.
Rev. B System Planning D-3 TM-P60 with Peeler Technical Reference Guide D.1.2 EPSON OPOS ADK EPSON OPOS ADK suppor ts the development environment necessary for OLE for Retail POS (OPOS) application development by OPOS Cont rol proposed by the UnifiedPOS Committees and supplies a printer driver (OCX ) conforming to OP OS.
D-4 System Planning Rev. B EPSON OPOS ADK Contents Any installer later than EPSON OP OS ADK Ver2.10 supports the silent install function that can install the OPOS environment without a user interfac e, which offers easier installation.
Rev. B System Planning D-5 TM-P60 with Peeler Technical Reference Guide D.1.3 ESC/POS Command Print/control by ESC/POS commands is dire ct control for TM printers using the ESC/POS commands proposed by EPSO N. Sending ESC/POS commands to the printer from an application enables direct control of the printe r.
D-6 System Planning Rev. B.
Rev. B FAQ E-1 TM-P60 with Peeler Technical Reference Guide Appendix E FAQ Q 1. Can I use the TM-P60 with Peeler in the Ad-Hoc mode? A 1.1 The TM-P60 wi th Peeler supports the Ad-Hoc mode for the first setup only.
E-2 FAQ Rev. B Q 4. BATT LED lights or flashes. What should I do? A 4.1 There is no remaining battery charge. You can confirm the rema ining battery charge by the BATT LED condition.
Rev. B FAQ E-3 TM-P60 with Peeler Technical Reference Guide A 6.4 TM-P60 with Peeler is near something that makes noise. Communication may be diffic ult near a microwave or motor. Move the AP or TM-P 60 with Peeler and confirm that communication is po ssible away from anything that makes noise.
E-4 FAQ Rev. B Q 8. Searching on the network takes several minutes. A 8.1 The IP address is set redundantly. When the same IP address is set for more than one device connected to the network, searching takes time and communication may be impossi ble. Confirm the settings for the devices.
Rev. B Consumable Specifications F-1 TM-P60 with Peeler Te chnical Reference Guide Appendix F Consumable Specifications This chapter includes information on receipt roll paper and label roll paper.
F-2 Consumable Specifications Rev. B ❏ Take-up roll paper width: • 58 mm paper width: 58 mm + 0/-1.0 mm • 60 mm paper width: 60 m m +0/-1.0 mm ❏ Roll paper diameter: • Maximum 51 mm ❏ Roll paper spool outside diameter: • 31.4 mm or more Note: Paper must not be pasted to the roll paper spool.
Rev. B Consumable Specifications F-3 TM-P60 with Peeler Te chnical Reference Guide ❏ Roll paper end treatment: • For best print quality and reliability, select the proper print density for the paper type used. See the table below. Print dens ity can be set with a memory switch.
F-4 Consumable Specifications Rev. B Note: The allowable relation between the reflecting rate in the black mark po rtion (1) and the non black mark portion (2) must be as shown in the table below: The reflecting rate means the value which is measu red with a Macbeth density meter (PCMII) D filter.
Rev. B Consumable Specifications F-5 TM-P60 with Peeler Te chnical Reference Guide Example: Liner width: 59.5 mm/Label width: 56 mm Note: The printable area may be out of alignment by 2.8 mm {0.11"} maximum (left or right), due to the paper position or tolerance of parts.
F-6 Consumable Specifications Rev. B F.1.1.2 Receipt paper ❏ Printable area for receipt pape r ❏ Paper width and printable area (Numeric values used here are average values fo r designing. Only the paper width dimension is exact. The values in parentheses are th e maximum value for the paper tolerance.
.
EPSON SEIKO EPSON CORPORATION.
Een belangrijk punt na aankoop van elk apparaat Epson TM-P60 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Epson TM-P60 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Epson TM-P60 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Epson TM-P60 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Epson TM-P60 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Epson TM-P60 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Epson TM-P60 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Epson TM-P60 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.