Gebruiksaanwijzing /service van het product LRP2000 van de fabrikant Escort
Ga naar pagina of 140
Operator ’ s Manual LRP2000 Passive Reader/W riter Manual Revision 04, 04-04 Publication # 17-1050.
LRP2000 Long-Ra nge Passive Reader/Wr iter ii Escort Memory Systems W arranty Escort Memory Systems warrants that all product s of it s own manufactur e conf orm to Escort Memory Systems specifi- cati.
LRP2000 Passive Reader/Writer i Chapter 1 Introduction 1.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1.2 Unpacking and Inspection . . . . . . . . . . .
Table of Contents ii LRP2000 Passive Reader/Writer 5.2.6 Return to Main Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 5.3 Download New Program . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents LRP2000 Passive Reader/Writer iii 6.5.10 ABxF Command 82H: Read Data an d SN All . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 6.5.11 ABxF Command 83H: Start/Stop Cont inuous SN Read All . . . . . . . . . . . . . . .
1 LRP2000 Passive Reader/Writer 1 Introduction 1.1 Introduction Escort Memory Systems' passive read/write system is a complete family of field- proven read/write Ra dio- Frequency Identification (RFID) products. The system consist s of RFID tags, reader/writers, antennas, controllers, bus interfaces, and ancillary equipment.
Introduction LRP2000 Passive Reader/Writer 2 1.3 FCC Compliance This equipment has been tested and found to comply with the limits for a Class B digit al device, pursuant to Part 15 o f the FCC Ru les. These limits are designed to prov ide reasonab le protect ion against harmful interference in a resident ial inst allation.
Introduction 3 LRP2000 Passive Reader/Writer 1.3.1 FCC Certifications.
Introduction LRP2000 Passive Reader/Writer 4.
Introduction 5 LRP2000 Passive Reader/Writer 1.4 CE S t atement This product complies with the Eu ropean Community's CE st andards and has been tested and certified to meet the required standard s, EN 300 3300-2 and EN 301 489-3. It is the responsibility of the system installer to ensure that it is used in compliance with local regulations.
Introduction LRP2000 Passive Reader/Writer 6 1.5 Changes and Modifications Any changes or modifications to the LRP2000 not ex pressly approved by Escort Memory Systems could void the user's authority to opera te the equipment.
7 LRP2000 Passive Reader/Writer 2 Inst allation and Guidelines 2.1 Dimensions Figure 1 gives the dimensions for the LRP2000 controller . Figure 1: LRP2000 Dimensions.
Installation and Guidelines LRP2000 Passive Reader/Writer 8 Figure 2 shows the LRP2000 mounting hole locations. Figure 2: LRP2000 Mounting Hole Locations and Dime nsions.
Installation and Guidelines 9 LRP2000 Passive Reader/Writer Figure 3 gives the dimensions for the LRP2000-23 an tenna Figure 3: LRP2000-23 An tenna Dimensions.
Installation and Guidelines LRP2000 Passive Reader/Writer 10 Figure 4 gives the dimensions for the LRP2000- 26 an tenna. Figure 4: LRP2000-26 An tenna Dimensions.
Installation and Guidelines 11 LRP2000 Passive Reader/Writer 2.2 Inst allation Antenna Environment Electromagnetic radi ation and the pres ence of me tal within the reading fiel d of the antenna af fect the range of the LRP2000. Mount the an tenna to mi nimize the impact of these fa ctors.
Installation and Guidelines LRP2000 Passive Reader/Writer 12 T o assemble the LRP2000 antenna: 1. Place the ba se half on a flat surf ace and no te the position of the green dots shown in Figure 6.
Installation and Guidelines 13 LRP2000 Passive Reader/Writer 2. Align the halve s according to the green dot s and p lace the top half o f the antenna on the base half. See Figure 7. Check that the halves have matching ser ial numbers (see Figu re 6).
Installation and Guidelines LRP2000 Passive Reader/Writer 14 4. Slide the joining p late into place fr om below and secu r e the top row of fasteners. Make sure you d o not bind the connector or wire under the joining plate. Figure 9: Joining Plate and Fasteners 5.
Installation and Guidelines 15 LRP2000 Passive Reader/Writer Figure 1 1 shows a completed LRP2000-26 an tenna. Figure 1 1: Completed LRP2000-26 Antenna.
16 LRP2000 Passive Reader/Writer 3 Electrical Interface 3.1 Connectors and Wiring Figure 12 shows the front connector p a nel with the four strain reliefs and the RF connectors. The controller ships with sealing plugs in the strain reliefs. For an environment al seal, leave these plugs in place for any unused location.
Electrical Interface 17 LRP2000 Passive Reader/Writer Figure 1 3 shows an internal vi ew of the co ntroller . I t details the locations of all internal term inal blocks needed for wiring the system. Figure 13: Internal Connectors CAUTION: The controller contains ESD-sensitive compone nts.
Electrical Interface LRP2000 Passive Reader/Writer 18 3.2 Antenna Cabling Figure 14 shows the two antenna connectors at the base of the LRP2 000 antenna. Figure 14: Antenna Connect ors Connect one end of the ante nna cable assembly , CBL-14 75, to the antenna conne ctors at the base of the antenna.
Electrical Interface 19 LRP2000 Passive Reader/Writer 3.2.1 Connecting Single Antenna System Figure 15 shows how to connect the LRP2 000 an d antenna in a single antenna configur ation.
Electrical Interface LRP2000 Passive Reader/Writer 20 3.2.2 Connecting a Dual Antenna System In dual antenna systems, one LRP2000 serves as the master and the other acts as the slave. Figure 16 shows how to connect two LRP200 0s in a master/slave configuration.
Electrical Interface 21 LRP2000 Passive Reader/Writer 3.3 Dat a T erminal Blocks Figure 17 shows the LRP2000 RS232 terminal block J8 , and a det ail view the terminal arrang ement. Figure 17: J8 COM1 RS232/COM2 RS2 32 T able 1 lists the RS232 pinouts.
Electrical Interface LRP2000 Passive Reader/Writer 22 Figure 18 shows the LRP2000 COM1 RS422 terminal block, J10, and a detail view illustrating the arrangement of the ter minals.
Electrical Interface 23 LRP2000 Passive Reader/Writer The signal names given in T able 2 refer to the signal s from the LRP200 0, not the signals from the host. 3.4 Power Supply Wiring CAUTION: The antenna cables must be properly connected to bo th the controller and the antenna at any time that power is applied to the controller .
Electrical Interface LRP2000 Passive Reader/Writer 24 Figure 19 shows the LRP2000 power supply and spad e lugs. Figure 19: Input Power Supply Lugs Figure 20 shows the LRP2000 input power terminals.
Electrical Interface 25 LRP2000 Passive Reader/Writer 3.5 RS232 Wiring The recommended cable type for RS232 communication is Belden p art number 9941. S pecifications for Belden cables can be found at WWW .
Electrical Interface LRP2000 Passive Reader/Writer 26 Because of the narrow size of the strain reliefs on the LRP2000, the st an dard RJ-45 connector cannot be inserted through the strain relief. EMS re commends that you loosen the nut on the strain relief, feed through the cable, and crimp the conn ector in place.
Electrical Interface 27 LRP2000 Passive Reader/Writer 3.8.1 Input s The +IN terminal must be at a highe r positive potenti al than the -IN terminal for current to be sensed correctly . The voltage range is 4.5 to 30V b etween the +IN and the -IN inpu t s, and the maximum current is 25 mA.
Electrical Interface LRP2000 Passive Reader/Writer 28 3.8.2 Output s The output is limited to 30 VDC when of f and 500 mA . These are maximum ratings. A device that operate s at 200 mA may destroy the output due to inrush curr ent if that current exceeds 500 mA (such as an incandescent light).
Electrical Interface 29 LRP2000 Passive Reader/Writer Figure 23: J20 Output Connector T able 5: Output Connector Pinout Te r m i n a l Number Signal Name Polarity 1+ O U T A P o s i t i v e 2 - OUT A .
Electrical Interface LRP2000 Passive Reader/Writer 30 Figure 24: Input from Sourc ing Cont act Figure 24 shows the switch on the high side with t he low side grounded. As this is a “ Dry” contact (the current is limited to 15 mA), a high -quality sealed switch should be used.
Electrical Interface 31 LRP2000 Passive Reader/Writer Figure 26: Input from NPN Sens or Figure 26 shows an Open Collector NPN output from a photosensor switching to ground.
Electrical Interface LRP2000 Passive Reader/Writer 32 Figure 28: Sourcing Output 'Cont act Figure 28 shows a relay connected as a curr ent sourci ng “Contact.
Electrical Interface 33 LRP2000 Passive Reader/Writer Figure 30: Sinking Output LED Driver In Figure 30, the LED and current limiting resistor are in series between the positive su pp ly an d the +OUT terminal. The -OUT term inal is groun ded. The re sistor in series with the LED se ts the forward current.
Electrical Interface LRP2000 Passive Reader/Writer 34 3.9 Master/Slave Configuration Y ou can use the LRP2000 in a single or dual an te nna configur ation .
Electrical Interface 35 LRP2000 Passive Reader/Writer 3.9.2 DIP Switch Settings on the Slave T o set a LRP2000 to operate as a slave in a dual anten na inst allation, you must change the settings of DIP switch banks S1 and S2. For reference, T able 6 shows the settings for a master LRP2000.
Electrical Interface LRP2000 Passive Reader/Writer 36 T o change the switches to a slav e configuration, make the changes highlighted in T able 7. Make sure power to the LRP2000 is off b efore changing DIP switch settings. NOTE: Do not make any changes to switch bank S3 and S5.
37 LRP2000 Passive Reader/Writer 4 Communications Interface 4.1 Configuring the Serial Interface 4.1.1 COM1 In normal use for reading a nd writing RFID tags, comm unications with the LRP2000 occurs v ia the main communicat ions inte rface, CO M1.
Communications Interface LRP2000 Passive Reader/Writer 38 The communication options for the COM2 interf ace are listed in T able 10. The default configuration p arameters for COM2 are listed in T able 1 1.
Communications Interface 39 LRP2000 Passive Reader/Writer 4.1.3 Digit al Board DIP Switch The digit al board is mounted inside the LRP2000 enclos ur e closest to the wall with the cable entries. The first five switches of the main board set the COM1 bau d rate, electrical interf ace, and the download options for COM2.
Communications Interface LRP2000 Passive Reader/Writer 40 NOTE: By setting SW5 ON to enable down load, the default parameters will first be restored and saved to the non-volatile memory , erasing the previously stored communication and o perating parameters.
Communications Interface 41 LRP2000 Passive Reader/Writer Once connected, apply power to the LRP2000 and di re ct the PC's web br owser to http://192 .
Communications Interface LRP2000 Passive Reader/Writer 42 Click “Connect” to see the current configurat ion of the module as shown in Figure 37. Figure 37: Configuratio n Page.
Communications Interface 43 LRP2000 Passive Reader/Writer T o change the IP address, click “Server Properties” from the menu on the lef t. This loads the Server Properties p age as shown in Fi gure 38. Figure 38: Server Propertie s Page Click the “Edit” button next to the IP addres s field to display a separate window .
Communications Interface LRP2000 Passive Reader/Writer 44 Figure 39: LED Indicators T able 13: LED Indicators LED Color Meaning POWER RED The LRP2000 is receiving power COM1 GREEN / RED RED: Incoming .
Communications Interface 45 LRP2000 Passive Reader/Writer Flashing LED Signals Flashing LED indicators, or combinations of flashing LED indicato rs, are used to indicate cert ain con troller states, or transitions from one st ate to another .
Communications Interface LRP2000 Passive Reader/Writer 46 The E-DIAG LED and the E-CHAN 1 LEDs blink at t he same time to indicate the following errors: Number of Blinks Error 4 Faulty Network Connect.
LRP2000 Passive Reader/Writer 47 5 Menu Configuration The LRP2000 features a menu-dr iven program designed to give convenient access to the serial parame ters, restore default s, or change op er ating modes.
Menu Configuration LRP2000 Passive Reader/Writer 48 5.2 Set-Up Operat ing Paramete rs T o change the operating parameters of the LRP2000, enter 1 at the initial menu.
Menu Configuration 49 LRP2000 Passive Reader/Writer 5.2.3 Set Operating Mode The “[3] Set Operating Mode” menu allows you to choose the ABx command protocol the LRP20 00 uses, or configures it to enter Continuous Read Mode auto matically upon start- up .
Menu Configuration LRP2000 Passive Reader/Writer 50 If a two-character preamble is desir ed, you are prompted to enter the h exadecimal value of both characters. The promp ts shown below are if ABx Fast pr otocol was selected. If ABx ASCII protocol was selected, the prompt s will reflect that.
Menu Configuration 51 LRP2000 Passive Reader/Writer If option 2 or 3 is selected fro m th e “Po we r Up In Cont inu o us Read Mode ” me n u, the fo llow i ng prom pts appear to allow you to specif.
Menu Configuration LRP2000 Passive Reader/Writer 52 5.2.4 Set RF Communication *** Set RF Communication *** RF Communication Enter T ag Category Save Changes to EEPROM RF Communication Fast Mode or S tandard Mode se ts the RF dat a rate from the reader to the ta g and should be set to the default condition “Fast Mo de.
Menu Configuration 53 LRP2000 Passive Reader/Writer 5.3 Download New Program Before attempting to download new firmware to the LRP2000 main board, read the instructions provided in a readme.
Menu Configuration LRP2000 Passive Reader/Writer 54 Send the new firmware via your terminal emulation pr ogram in ASCII text or hexadecimal format. The firmware is automatically transferred to the DSP Fl ash Memory . W ait 10 seconds af ter the download is complete before re setting the LRP2000.
LRP2000 Passive Reader/Writer 55 6 RFID Communications 6.1 Introduction Conventions In this manual, numbers expressed in hexadecima l are appended with “H.
RFID Communications LRP2000 Passive Reader/Writer 56 6.1.1 ABx Command Set Listings T able 14, T able 15, and T able 16 list the ABx commands recognized by the LRP2000. NOTE: The delay between the characters of a command s ent to the contro ller cannot be longer than 200 ms.
RFID Communications 57 LRP2000 Passive Reader/Writer 6.2 Command Parameters 6.2.1 Command T imeout All single-tag and multi-tag command s have a timeout valu e th at is used to specify the time the controller will attempt to complete the specifie d operation.
RFID Communications LRP2000 Passive Reader/Writer 58 At the pallet l evel, a read command of the case level family coded t ags would produce the quantity of cases on the p allet and the case da ta and the qu antity of cases could be written to the pallet tag using the pallet t ag family code.
RFID Communications 59 LRP2000 Passive Reader/Writer 6.4 S t andard ABx Protocol The ABx standard is a binary pr otocol, word (2-byte) orie nted, so th e syntax table reports the most significant byte (MSB) and the least significant byte (LSB). In the serial transmission, the MSB is transmitted first.
RFID Communications LRP2000 Passive Reader/Writer 60 6.4.1 ABxS Command 04H: Fill T ag DESCRIPTION Fill an RFID tag with a one-byte value over multiple cont iguous addresses. DISCUSSION This command is commonly used to clear contiguous segments of a t ag's memory .
RFID Communications 61 LRP2000 Passive Reader/Writer 6.4.2 ABxS Command 05H: Read DESCRIPTION Read data fr om contiguous bytes of the RFID t ag's read/write memo ry . DISCUSSION This command is used to read bytes from contigu ous areas of tag memor y .
RFID Communications LRP2000 Passive Reader/Writer 62 6.4.3 ABxS Command 06H: W rite DESCRIPTION Writes data to an RFID tag. DISCUSSION This command is used to write segment s of data to contiguous ar eas of tag memory . It is capable of transferrin g up to 1 12 bytes of data transf erred from the Host with one command.
RFID Communications 63 LRP2000 Passive Reader/Writer 6.4.4 ABxS Command 07H: Read T ag Serial Number DESCRIPTION This command retrieves the eight-b yte tag serial number . DISCUSSION Each contro ller tag has a uni que serial n umber . Th is number cannot be changed and is not p art of the available data bytes.
RFID Communications LRP2000 Passive Reader/Writer 64 6.4.5 ABxS Command 08H: T ag Search DESCRIPTION Check to see if there is an RFID t ag in the antenna field. DISCUSSION This command activates the controlle r to search for the presence of a ta g within range of the antenna.
RFID Communications 65 LRP2000 Passive Reader/Writer In Continuous Read mode, the LEDs indic ate the following: The command and response fr om the controller are formatted as follows. This example places the controller in Co ntinuous Read mode and reads eight bytes of dat a from the tag starting at addre ss 0001H.
RFID Communications LRP2000 Passive Reader/Writer 66 T o exit Continuous Read mode, send the command with the r ead leng th vari able se t to 0 as shown b elow . The value of the othe r variables ar e not cons idered. 6.4.7 ABxS Command 14H: Get Memory S tatus DESCRIPTION Returns the lock status of th e specified blocks of data.
RFID Communications 67 LRP2000 Passive Reader/Writer 6.4.8 ABxS Command 16H: W rite Family Code DESCRIPTION Changes the family code o f an RFID tag. Response from controlle r: 6.4.9 ABxS Command 17H: Lock Family Code Description: Locks the Fa mily Code Byte t o its current value, so that it cannot be written.
RFID Communications LRP2000 Passive Reader/Writer 68 6.4.10 ABxS Command 82H: SN Read All DESCRIPTION Command 82H reads the serial numbers and the specifie d bytes of data from all RFID tags in the field or those with the specified Family ID. Returns the seri al number of the tags read, alo ng with tag data.
RFID Communications 69 LRP2000 Passive Reader/Writer Example Reads two bytes of dat a from the tag starting at add ress 0001H. A timeou t of 2 seconds (07D0H = 2000 x 1 ms increments) is set for the completi on of the SN Read All. The Family ID byt e i s s et to ze ro , s o a ll tag s will be read.
RFID Communications LRP2000 Passive Reader/Writer 70 6.4.1 1 ABxS Command 83H: S t art/ Stop Continuous SN Read All DESCRIPTION Command 83H star t s and stops continuous read all mode for multiple tag s. It reads the serial number and tag dat a. If the read length is zero (0), then only the tag's serial number is re ad.
RFID Communications 71 LRP2000 Passive Reader/Writer 00H 00H Serial Number byte /T ag 1 00H 01H Serial Number byte /T ag 1 00H 04H Serial Number byte /T ag 1 00H E0H Serial Number byte /T ag 1 00H 6CH.
RFID Communications LRP2000 Passive Reader/Writer 72 6.4.12 ABxS Command 84H: Fill T ag All DESCRIPTION Command 84H fills all RFID tags-in-field or all t ags in the same family , with a one-byte valu e over multiple contiguous addresses. DISCUSSION This command is commonly used to clear an RFID ta g's memory .
RFID Communications 73 LRP2000 Passive Reader/Writer 6.4.13 ABxS Command 85H: Read All DESCRIPTION Command 85H reads dat a from all RFID tags-in-fiel d , or those tags with th e specified Family ID. DISCUSSION This command is used to read segment s of data fr om contiguous ar eas of tag memory .
RFID Communications LRP2000 Passive Reader/Writer 74 Example Reads four byte s of data from the tag starting at address 000 1H. A timeout of 2 seco nds (07D0H = 20 00 x 1 ms increments ) is set for the completio n of the Read A ll. The Family ID byte is set to zero, so all tags are read.
RFID Communications 75 LRP2000 Passive Reader/Writer 6.4.14 ABxS Command 86H: Write All DESCRIPTION Command 86H writes data to all RFID t ags , or all tags with the same Family ID. DISCUSSION This command is used to write segment s of data to contiguous ar eas of tag memory .
RFID Communications LRP2000 Passive Reader/Writer 76 6.4.15 ABxS Command 87H: Read T ag SN All DESCRIPTION Command 87H retrieves the eig ht-byte tag seria l number from all tags, or those with the specified Family ID number . DISCUSSION Each ISO-15693 compliant ta g has an unique serial number (over 280 trillion possibilitie s).
RFID Communications 77 LRP2000 Passive Reader/Writer 6.4.16 ABxS Command 88H: T ag Search All DESCRIPTION Command 88H checks to see if there is an RFID tag with in range of the antenna. DISCUSSION This command activates controller to look for a t ag in ra nge.
RFID Communications LRP2000 Passive Reader/Writer 78 6.4.17 ABxS Command 8BH: Write Family Code All DESCRIPTION Command 8BH can be used to write the fa mily code of all ta gs in the field . It can also be used to selectively rewrite the family codes of tags with family codes already set to a particular va lue.
RFID Communications 79 LRP2000 Passive Reader/Writer 6.4.18 ABxS Command 8CH: Lock Family Code All DESCRIPTION Command 8CH locks the family codes of t ags in the fie ld. Once locked, the family codes cannot be changed or unlocked. DISCUSSION The command must pass a family code to select the t ags whose family code will be locked.
RFID Communications LRP2000 Passive Reader/Writer 80 6.4.19 ABxS Command 8DH: St art/Stop Continuous Read All DESCRIPTION Command 8DH star ts and stop s Continuous Read All mode for multiple tags. DISCUSSION The S tart/S top Continuous Read All mode is set by the length byte.
RFID Communications 81 LRP2000 Passive Reader/Writer After the contro ller sends the acknowledgment, it sends the re ad data from the three t ags. Dat a response from controlle r MSB LSB Remarks AAH 8.
RFID Communications LRP2000 Passive Reader/Writer 82 6.4.20 ABxS Command 91H: Memory Lock All DESCRIPTION Command 91H locks contiguous blocks of read- write memory . Once bytes are locked, they cannot be written to, nor can they be unlocked. DISCUSSION The memory can be locked only in contiguou s blocks.
RFID Communications 83 LRP2000 Passive Reader/Writer 6.4.21 ABxS Command 94H: SN Fill DESCRIPTION Command 94H fills only the RFID tag specified by the serial nu mber with a one-byte value over mu ltiple contiguous addresses. DISCUSSION This command is commonly used to clear an RFID ta g's memory .
RFID Communications LRP2000 Passive Reader/Writer 84 Example Writes 'A' ( 41H) to a single t ag, star ting at t ag addr ess 0005H for the n ext consecutive 40 bytes. The family code is set t o 00H. A timeou t of 2 seco nds (07D 0H = 2000 x 1 ms incremen ts) is set for the completion of the command.
RFID Communications 85 LRP2000 Passive Reader/Writer 6.4.22 ABxS Command 95H: SN Read DESCRIPTION Command 95H reads dat a from a specified RFID t ag. DISCUSSION This command is used to read segment s of data fr om contiguous ar eas of tag memory .
RFID Communications LRP2000 Passive Reader/Writer 86 6.4.23 ABxS Command 96H: SN Write DESCRIPTION Command 96H writes data to a single RFID t a g specified by its serial num ber . DISCUSSION This command writes segment s of dat a to contiguous ar eas of tag memory .
RFID Communications 87 LRP2000 Passive Reader/Writer Example Writes four bytes o f data, starting at address 0 001H. A timeout of 2 second s (07D0H = 2000 x 1 ms increments) is set for the completion of th e Write.
RFID Communications LRP2000 Passive Reader/Writer 88 6.4.24 ABxS Command 10H: Set Outp ut DESCRIPTION Command 10H set s the states of the outp ut lines and output LEDs “A” through “D.” DISCUSSION This command sets the st ate of the digit al ou tput li nes using a one-byte parameter , O utput St at us.
RFID Communications 89 LRP2000 Passive Reader/Writer 6.4.25 ABxS Command 1 1H: Input St atus DESCRIPTION Command 1 1H returns the status of user input s. DISCUSSION This command interrogate s th e st ate of the user input lines and retu rn a one -b yte p a ra meter , Input S tatus.
RFID Communications LRP2000 Passive Reader/Writer 90 6.5 ABx Fast Protocol The ABx Fast protocol dif fers from the Abx S tandard Pr otocol in tha t the atomic data element is a byte instead of a 16-bit word . ABx Fast comm ands and respon ses also contain a two-byte word to indicate the size of the packet being sent.
RFID Communications 91 LRP2000 Passive Reader/Writer The summed values begin with the Command Size a nd en d with the timeout value. That sum, less overflow , is subtracted from FFH for the checksum value.
RFID Communications LRP2000 Passive Reader/Writer 92 6.5.1 ABxF Command 04H: Fill T ag DESCRIPTION Command 04H fills an RFID t ag with a one-byte value over multiple contiguous a ddresses. DISCUSSION This command is commonly used to clear an RFID ta g's memory .
RFID Communications 93 LRP2000 Passive Reader/Writer Example Writes 'A' (41H) to the t ag starting at address 0005H and contin uing for the next co nsecutive 40 bytes. A timeout of 2 seconds (07D0H =2000 x 1 ms increment s) is set for the completion of the configu ration.
RFID Communications LRP2000 Passive Reader/Writer 94 Example Reads four byte s of data from the tag starting at address 000 1H. A timeout of 2 seco nds (07D0H = 20 00 x 1 ms increm ents) is set for the completion of the Read . 6.5.3 ABxF Command 06H: W rite DESCRIPTION Command 06H writes data to an RFID tag.
RFID Communications 95 LRP2000 Passive Reader/Writer Example Writes four byte s of data to th e tag st arting at add ress 0000H. A timeout of 2 seconds (07D0H = 2000 x 1 ms increments) is set for t he comple tion of the Write. 6.5.4 ABxF Command 07H: Read T ag Serial Number DESCRIPTION Command 07H retrieves the eig ht-byte tag seria l number .
RFID Communications LRP2000 Passive Reader/Writer 96 Example This example waits until a t ag is in range and then reads the eight-byte serial nu mber . In this exam ple, the serial number is F272030 0000104E0. 6.5.5 ABxF Command 08H: T ag Search DESCRIPTION Command 08H checks for an RFID t ag in the controller field.
RFID Communications 97 LRP2000 Passive Reader/Writer Example Checks for an RFID tag within range of the anten na. A timeout of 2 seconds (07D0H = 2000 x 1 ms increment s) is set for the completion of the T ag Search.
RFID Communications LRP2000 Passive Reader/Writer 98 This example places the controller in Co ntinuous Read mode and reads eight bytes of dat a from the tag, starting at addre ss 0001H. A delay between identical reads of 2 seconds (0002 H = 2 x 1 second increments) is set.
RFID Communications 99 LRP2000 Passive Reader/Writer Example 6.5.8 A BxF Command 16H: W rite Family Code DESCRIPTION Command 16H changes the family co de of an RFID tag.
RFID Communications LRP2000 Passive Reader/Writer 100 6.5.9 ABxF Command 17H: Lock Family Code DESCRIPTION: Command 17H locks the family code byte to its current value, so tha t it cannot be written. Once locked, the family code cannot be unlo cked. 6.
RFID Communications 101 LRP2000 Passive Reader/Writer Example This example re ad s fou r by te s of da ta from the tag starting at address 0001 H. A timeout of 2 seconds (07D0H = 2000 x 1 msec increment s) is set for the co mpletion of the SN Block Read All.
RFID Communications LRP2000 Passive Reader/Writer 102 SN Byte 1/tag 3 71H SN Byte 2/ tag 3 72H SN Byte 3/tag 3 03H SN Byte 4/tag 3 00H SN Byte 5/tag 3 00H SN Byte 6/tag 3 01H SN Byte 7/tag 3 04H SN By.
RFID Communications 103 LRP2000 Passive Reader/Writer 6.5.1 1 ABxF Command 83H: St art/ Stop Continuous SN Read All DESCRIPTION Command 83H star t s and stops continuous read all mode for multiple tag s. It reads the serial number and tag dat a. While in this mode, an y other command can be is sued and it will be handled properly .
RFID Communications LRP2000 Passive Reader/Writer 104 Example S tarts continuous read of three bytes star ting at addr ess two, has a repeat count of four , and the family code is set to 00H, so that all tags in the fie ld respond. After the contro ller sends the acknowledgement, it sends the dat a read from the ta gs in the field.
RFID Communications 105 LRP2000 Passive Reader/Writer Response from controlle r Field Content Header 0202H Response Size 000BH Command Echo/T ag 1 83H SN Byte 1/tag 1 A6H SN Byte 2/ tag 1 72H SN Byte .
RFID Communications LRP2000 Passive Reader/Writer 106 6.5.12 ABxF Command 84H: Fill All DESCRIPTION Command 84 H fills all RFID tags-in-field or all t ags in the same family , with a one-byte value over multiple contiguous addresses. DISCUSSION This command is commonly used to clear an RFID ta g's memory .
RFID Communications 107 LRP2000 Passive Reader/Writer Example Writes 41H—the ASCII ch aracter "A"—to all tags with fa mily code 03H, st arting at address 000 5H for the next consec utive 40 By tes. A timeout of 2 seco nds (07D0H = 2000 x 1 ms ec increm ents) is set for th e completion of the configuration.
RFID Communications LRP2000 Passive Reader/Writer 108 Example Reads four bytes of dat a from t ags with Family ID AAH, st arting at addr ess 0001H. A timeou t of 2 seconds (07D0H = 2000 x 1 msec increment s) is set for the comple tion of the Blo ck Read All.
RFID Communications 109 LRP2000 Passive Reader/Writer 6.5.14 ABxF Command 86H: Block Wr ite All DESCRIPTION Command 86H writes a block of data to an RFID ta g. DISCUSSION The Block Write All command is used to write segmen ts of dat a to contiguous areas of t ag memory .
RFID Communications LRP2000 Passive Reader/Writer 11 0 Example Writes four byte s of data to th e tag st arting at add ress 0000H. A timeout of 2 seconds (07D0H = 2000 x 1 msec increment s) is se t fo r the completion of the Block W r ite All. Family ID is set to 00H so all tags-in-field are written to.
RFID Communications 111 LRP2000 Passive Reader/Writer Example This example reads the eigh t-byte serial nu mber from all t ags permitted b y the Family ID and Reser ved.
RFID Communications LRP2000 Passive Reader/Writer 11 2 6.5.16 ABxF Command 88H: T ag Search All DESCRIPTION Command 88H searches fo r tags within range of th e antenna. DISCUSSION This command activates the controller to look for tag s within range of the antenna.
RFID Communications 11 3 LRP2000 Passive Reader/Writer 6.5.17 ABxF Command 8D H: Stop/S tart Continuous Read All DESCRIPTION Command 8DH star ts and stop s continuous read mode for multiple tags. DISCUSSION The S tart/S top Continuous Read All mode is initiated by issuing the command with th e Number of Bytes set to any valid nonzero value.
RFID Communications LRP2000 Passive Reader/Writer 11 4 After the contro ller sends the acknowledgment, it sends the read data from the two t ags. 6.5.18 ABxF Command 91H: Memo ry Lock All DESCRIPTION Command 91H locks contiguous blocks of read- write memory .
RFID Communications 11 5 LRP2000 Passive Reader/Writer Example This example locks blocks 0-2 on all tags-in-field wit h the family code of 02H. T wo tags are found and locked. 6.5.19 ABxF Command 8B H: W rite Family Code All DESCRIPTION Command 8BH can be used to write the fa mily code of all ta gs in the field .
RFID Communications LRP2000 Passive Reader/Writer 11 6 Example This example ch an ge s th e fam ily co de depe nd ing on t he current value of the family code. T wo tags are found with family code 02H and are chan ged to 03H. 6.5.20 ABxF Command 8C H: Lock Family Code All DESCRIPTION Command 8CH locks the family codes of t ags in the fie ld.
RFID Communications 11 7 LRP2000 Passive Reader/Writer Example This example loc ks the family c ode on all tags with the family code of 02H. T wo tags are found and locked. 6.5.21 ABxF Command 94H: SN Fill DESCRIPTION Command 94H fills only the RFID tag specified by se rial number with a one-byte value over multiple contiguous addresses.
RFID Communications LRP2000 Passive Reader/Writer 11 8 Example This example fills the tag with seri al number 1DB0320 000104E0 with FFH. Command from Host Response form Controller Field Content Field .
RFID Communications 11 9 LRP2000 Passive Reader/Writer 6.5.22 ABxF Command 95H: SN Block Read DESCRIPTION Command 95H reads a block of dat a from a specified RFID tag. DISCUSSION This command is used to read segment s of data from contigu ous areas of tag memory .
RFID Communications LRP2000 Passive Reader/Writer 120 Example This example reads 1 0 bytes from the t ag with ser ial number 1 DB032000 0104E0 st a rting at addre ss 0AH.
RFID Communications 121 LRP2000 Passive Reader/Writer 6.5.23 ABxF Command 96H: SN Block Write DESCRIPTION Command 96H writes data to a single RFID t a g specified by its serial num ber . DISCUSSION This command is used to write dat a to contiguous area s o f tag memory .
RFID Communications LRP2000 Passive Reader/Writer 122 Example This examp le writes 4 bytes to the tag with serial number 1DB0320000104E0 st arting at address 0AH.
RFID Communications 123 LRP2000 Passive Reader/Writer 6.5.24 ABxF Command 10H: Set Output DESCRIPTION Command 10H set s the states of the outp ut lines and output LEDs "A" through "D." DISCUSSION This command sets the st ate of the digit al ou tput li nes using a one-byte parameter , O utput St at us.
RFID Communications LRP2000 Passive Reader/Writer 124 Example The following example set s Output B only and resets A, C, and D. 6.5.25 ABxF Command 1 1H: Input St atus DESCRIPTION Command 1 1H returns the status of user input s.
RFID Communications 125 LRP2000 Passive Reader/Writer Example The following example shows only inpu t B is ON, and A, C, and D are OFF . Field Content Header 0202H Command Size Packet length in bytes .
RFID Communications LRP2000 Passive Reader/Writer 126 6.6 ABx ASCII Protocol The ABx ASCII Protocol is based on the ABx Fast pr otocol. It uses the same headers and termina tor (already ASCII ch aracters) an d convert s the hex value of command and dat a bytes to print able ASCII ( two- digit hexade cimal notation).
RFID Communications 127 LRP2000 Passive Reader/Writer If the controller encounters a fault, it resp onds with the following: Most RF operations also require additional parameters and data that will be included in the command stream between the command code or echo and the te rminator .
RFID Communications LRP2000 Passive Reader/Writer 128 The ASCII character string for a fill of 32 bytes, from address 0 with 55H value, timeout 5 sec., follows: Command from Host Response from Control.
RFID Communications 129 LRP2000 Passive Reader/Writer 6.7 ABx Error Codes 6.7.1 Multi-t ag Error Codes The LRP2000 returns an error if it encounters a fault during operation.
RFID Communications LRP2000 Passive Reader/Writer 130 6.7.3 ABx Fast Error Codes The format of the error response is shown in th e table below . Example A Block Write fail erro r me ssage would appear as: 0202 0002 FF06 F803H. 6.7.4 ABx ASCII Error Codes The format of the er ro r re sp on se is shown bel ow .
131 LRP2000 Passive Reader/Writer 6.7.5 Multi-t ag Command Error Code When the mult i-tag commands encounter a fault conditio n, they indic ate the er ror in a ST A TUS byte returned in th e response . If any of the flag bits of the S tatus byte are set, then an erro r has occurred during command execution.
132 LRP820 Passive Reader/Writer Appendix A S pecifications A.1 Electrical Supply V oltage: 28-30 Vdc Power Consumption: 56W (2.0 A @ 28Vdc) A.2 Communication RF Interface: ISO/IEC 15693 Pas sive RFID System Bus Interface: Ethernet TCP/IP (Option) COM1: RS232/RS422 COM2: RS232 Inputs: Fo ur industrial-level input s , 4.
LRP2000 Passive Reader/Writer 133 Appendix B Models and Accessories B.1 A vailable Models B.2 Options B.3 Accessories B.4 T ags Part Number Description LRP2000-26 Long range, passive controller; RS232.
134 LRP2000 Passive Reader/Writer Appendix C ASCII Chart Decimal Hex Character Decimal Hex Charact er 000 00 NUL 032 20 (SP ACE) 001 01 SOH 033 21 ! 002 02 STX 034 22 " 003 03 ETX 035 23 # 004 04.
ASCII Chart 135 LRP2000 Passive Reader/Writer 064 40 @ 096 5F • 065 41 A 097 60 a 066 42 B 098 61 b 067 43 C 099 62 c 068 44 D 100 63 d 069 45 E 101 64 e 070 46 F 102 65 f 071 47 G 103 66 g 072 48 H.
Een belangrijk punt na aankoop van elk apparaat Escort LRP2000 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Escort LRP2000 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Escort LRP2000 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Escort LRP2000 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Escort LRP2000 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Escort LRP2000 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Escort LRP2000 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Escort LRP2000 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.