Gebruiksaanwijzing /service van het product Lazer Z van de fabrikant Exmark
Ga naar pagina of 44
.
i ! W ARN I N G ! WA R N I N G . . . ! CAUTION The engine ex haust from this produ ct contains chemicals k nown to the State of California to cause cance r , birth d efects, or other reproductive harm.
ii EXMARK PA RTS PLUS PROGRA M EFFECTIVE DATE: September 1, 1995 Program If your Ex mark dealer does not have the Ex mark part in stock, Exmark w ill get the parts to the dealer the nex t business day or the part will be FREE* Guaranteed!! How the Program Works 1.
iii CONGRATULATIONS on the purchase of your Exmark Mower. This product has been carefully designed and manufactured to give you a maximum amount of dependability and years of trouble-free operation. OPERATOR'S MANUAL This manual contains assembly, operating, maintenance, adjustment and safety instructions for your Exmark mower.
iv TABLE OF CONTENTS 1. SAFETY PAGE 1.1 Safety Alert Symbol ............................... 1 1.2 Training .......................................... 1 1.3 Preparation ..................................... 1-2 1.4 Operation ...........................
- 1 - 1. SAFETY 1.1 SAFETY ALERT SYMBOL THIS SAFETY ALERT SYMBOL IS USED BOTH IN THIS MANUAL AND ON THE MACHINE TO IDENTIFY IMPORTANT SAFETY MESSAGES WHICH MUST BE FOLLOWED TO AVOID ACCIDENTS.
- 2 - • • • • Fuel is Highly Flammable. DO NOT smoke while refueling. Refuel only in a well ventilated area, or refuel outdoors. • • • • Store fuel in containers specifically designed for this purpose. • • • • Add fuel before starting the engine.
- 3 - 1.4.9 Start the engine carefully with feet well away from the blades. 1.4.10 Keep hands, feet and clothing away from rotating parts while the mower is being operated. 1.4.11 Stop the engine and disconnect the spark plug wire(s)and/ or remove key: a) Before checking, cleaning or working on the mower.
- 4 - 1.5 MAINTENANCE AND STORAGE 1.5.1 For engine maintenance, follow the engine manufacturer's recommendations precisely as stated in the engine manual. 1.5.2 If carburetor adjustment is necessary, stand to one side and keep feet and hands clear while making adjustments.
- 5 - PART NO. 323550 LOCATION: Upper Handles (Both Sides) PART NO. 403005 LOCATION: Front Corners o f D ec k PART NO. 303508 LOCATION: Right Rear Corner o f D ec k 8.5 HP B&S PART NO. 543631 LOCATION: Upper Handle Console PART NO. 303517 LOCATION: Left Side, Rear Surface Engine Deck PART NO.
- 6 - 2. SPECIFICATIONS 2.1 MODEL NUMBER: 2.2 ENGINE 2.2.1 Engine Specifications: See your engine owner's manual. 2.2.2 RPM (No Load): 3600 rpm 2.3 FUEL SYSTEM 2.3.1 Capacity: 5 gal. (18.9 liter) 2.3.2 Type of Fuel: Use only clean, fresh, regular grade, unleaded gasoline with the pump sticker octane rating of 87 or higher.
- 7 - 2.3.3 Fuel Filter: Replaceable in-line 2.3.4 Fuel Shut Off Valve: in-line, 1/4 turn 2.4 SAFETY INTERLOCK SYSTEM Operator must have the transmission in neutral and blades disengaged to start engine. Release of Operator Presence Control (OPC) levers will cause engine to stop if transmission is not in neutral and/or blade drive is engaged .
- 8 - 2.9.6 Cutting Height: Adjusts in 1/4" (.63 cm) or smaller increments by various adjustments of caster spacers, blade spacers and axle height, from 1” to 4 1/4” (2.5 cm - 10.8 cm). 2.10 DIMENSIONS 2.10.1 Overall Width: 32" 36" 48" ♦ ♦ ♦ ♦ 48” ◊ ◊ ◊ ◊ Discharge chute 42.
- 9 - 3.5 Install casters to front of deck using appropriate hardware from the bolt bag (eight 3/8 x 3/4" bolts and eight 3/8" whizlock nuts); tightening the lower four bolts first, then the top four.
- 10 - FIG. 2 UPPER HANDLE HEIGHT ADJUSTMENT 3.8.1 Attach throttle cable to engine. For Kohler, Kawasaki, and B&S 10.5 hp Engines with "positive" detents in throttle cable for both idle and full throttle positions. a) Position the throttle control lever (on console) in the full throttle (but not choke) position.
- 11 - FIG 4 KAWASAKI SPEED CONTROL (THROTTLE CABLE HOOK-UP) FIG 5 B&S 10.5 hp SPEED CONTROL (THROTTLE CABLE HOOK-UP) d) Pull cable upward (rearward for B&S) until alignment holes in control plate lever and control plate line up. For Kawasaki a 15/64 drill bit can be inserted through these two holes to align them.
- 12 - For B&S 8.5 hp Engines, a) Position the throttle control lever (on console) 1/8" from the lower end of the slot. Route the throttle cable along the right side of the upper handle, under the fuel tank support, and position the cable on the left side of the engine.
- 13 - FIG. 7 THIS CLEARANCE SHOULD BE EQUAL FIG. 6 SHIFTER LEVER TO TRANSMISSION FIG. 8 THIS CLEARANCE SHOULD BE EQUAL 3.8.5 Install and adjust wheel drive linkages.
- 14 - FIG. 10 NEUTRAL LOCK LEVER CLEARANCE NOTE: Neutral lock/park brake latch clearance should be checked when there is a slight upward force placed on the drive levers to remove any "slack" in the linkage.
- 15 - 3.8.8 Route the long, unattached wiring harness lead up the left hand side of the handle and connect the two leads, in any order, to the operator presence control switch terminals on the inside of the control console.
- 16 - FIG. 12 DRIVE LEVER, NEUTRAL LOCK/PARK BRAKE LATCH OPERATION 4.1.4 Operator Presence Control (OPC) Levers: Located on the upper handle assembly directly above the handle grips. When these levers are depressed, the OPC system senses that the operator is in the normal operator's position.
- 17 - a detent at the "idle" position, continuing rearward past this detent will shut off the engine . B&S 8.5 hp Engines: For the B&S 8.5 hp engine the choke control is located on the left side of the engine (from operator's position).
- 18 - • • • • If fuel is spilled, DO NOT attempt to start the engine. Move away from the spill and avoid creating any source of ignition until fuel vapors have dissipated. 4.3 OPERATING INSTRUCTIONS 4.3.1 Read the Engine Owner's Manual carefully for detailed operating instructions and maintenance regarding the engine.
- 19 - Close fuel shut-off valve if machine will not be used for a few days; when parking inside a building; or when transporting the unit. 4.3.4 Drive Lever/Neutral Lock/Park Brake Latch Operation: To lock the drive levers in “neutral” squeeze the drive levers back to the neutral position.
- 20 - 4.4 TRANSPORTING • • • • If loading with ramps, be sure ramps are properly supported and strong enough to support the unit. • • • • If necessary, use assistance when loading or unloading. Keep feet and legs out from under the unit when loading and unloading Be sure fuel shut-off valve is closed.
- 21 - 5.1.2 Clean engine air cooling system. Service Interval: See Engine Owner's Manual a) Stop engine and remove spark plug wire(s). b) Clean all debris from engine air intake screen and from around engine shrouding. 5.1.3 Clean grass build-up under deck and check mower blades.
- 22 - either the mower blades are engaged, or the transmission shifter lever is not in neutral and the operator removes both hands from the handles, the mower engine must stop . b) To determine if the OPC is in operating condition, clear area of bystanders.
- 23 - engines). Clean around oil filter and unscrew filter to remove. Before the new filter is installed, apply a thin coating of oil on the surface of the rubber seal. Turn filter clockwise until rubber seal contacts the filter adapter, then tighten filter an additional 2/3 to 3/4 turn.
- 24 - 5.1.11 Inspect belt wear. Service Interval: 40 hrs. a) Stop engine and remove spark plug wire(s). b) Remove the cutter deck belt shield to check mower primary and secondary blade drive belt condition. NOTE: A Secondary blade drive belt is used on 48" units.
- 25 - c) Replace 5-speed gearbox grease yearly. Use 18 oz. Of Peerless grease (Part No. 788067). See Section 5.1.10. d) Lubricate pivot points with a spray penetrating lubricant as directed below. SPRAY LUBRICANT CHART PIVOT POINTS NO. of PLACES 32" 36" 48" SERVICE INTERVAL 1.
- 26 - 5.1.19 An anti-seize compound is used on the blade drive pulley hub, located on the engine PTO shaft (this allows for ease of removal of the pulley). 5.1.20 Dielectric grease is used on all blade type electrical connections to prevent corrosion and loss of contact.
- 27 - Refer to the charts and illustrations on the following pages to properly adjust for desired cutting height. FIG. 14 FIG. 15 CASTER HEIGHT ADJUSTMENT AXLE HEIGHT ADJUSTMENT These models have five (5) axle positions; four (4) 1/2" caster spacers; one (1) 3/16" caster spacer, and four (4) blade spacers.
- 28 - NOTE: The axle positions are in 1/2" increments and the large caster spacers are 1/2" thick. Therefore, by adjusting the same number of 1/2" caster spacers as axle hole positions the blades will retain the same front-to-back tip (rake).
- 29 - 5.2.4 Wheel drive belts and scrapers. a) If wheel traction appears to be slipping, drive lever rods may be touching bottom of neutral lock/park brake latch slot. To adjust, refer to directions in Section 3.8.5. NOTE: There are three (3) adjustment holes for the wheel drive spring tension bolt (Refer to Section 5.
- 30 - 5.2.6 Secondary belt (48" only) . a) Stop engine and remove spark plug wire(s). b) The secondary drive belt is adjusted via the belt tension rod (See Figure 16). The 5/16" nyloc adjustment nut is located at the rear, right corner of engine deck.
- 31 - turn setscrew all the way in then back out 1-1/2 turns. IMPORTANT : Screwing setscrew in too far will prevent the transmission from shifting. 5.
- 32 - 6. TROUBLE SHOOTING 6.1 MOWER PULLING LEFT OR RIGHT. a) Check idler arm pulleys and drive sheaves for mud and/or grass buildup. Check for proper scraper position. See 5.2.4. b) Check to be sure idler arms pivot freely, if not, lubricate idler pivots.
- 33 - NOTE: After carefully checking the previous steps, attempt to start the engine. If it does not start, contact your authorized Exmark service dealer. ENGINE TROUBLESHOOTING When a problem occurs, do not overlook the simple causes. For example, starting problems could be caused by an empty fuel tank, key switch not "ON" etc.
- 34 - 8. WIRING DIAGRAMS.
- 35 - 9. WARRANTY Limited Warranty Exmark Commercial Turf Equipment Exmark Mfg. Co. Inc. ("Exmark") warrants on the terms and conditions herein, that it will repair, replace or adjust any part manufactured by Exmark and found by Exmark(in the exercise of its reasonable discretion)to be defective in factory material or workmanship.
- 36 - instructions provided by Exmark; (vi) repair or replacement arising as a result of any operation from turf equipment that has been altered or modified so as to, in the determination of Exmark, .
- 37 - SERVICE RECORD Date Descripti on of Work Done Service Done By.
- 38 - T H I S I S A 1 5 ° SL O P E T H I S I S A 1 0 ° S L O P E T H I S I S A 5 ° S L O P E ALIGN THIS EDGE WITH A VERTICAL SURF ACE (TREE, BUILDING, FENCE POST , POLE ETC.
SEE EXMARK’S COMPLETE LINE OF PRODUCTS FOR TURF CARE LAZER Z ™ LAZER Z ™ HP EXPLOR ER ® TURF RANGER ® TURF TRACER ® TURF TRACER ® HP VIKING HYDRO METRO ™ METRO ™ HP SELF STEERIN G SULK Y GRASS CATCHER MICRO-MULCH ™ ACCESS ORY ® MF G .
Een belangrijk punt na aankoop van elk apparaat Exmark Lazer Z (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Exmark Lazer Z heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Exmark Lazer Z vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Exmark Lazer Z leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Exmark Lazer Z krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Exmark Lazer Z bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Exmark Lazer Z kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Exmark Lazer Z . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
