Gebruiksaanwijzing /service van het product LZ27KC604 van de fabrikant Exmark
Ga naar pagina of 48
For Serial Nos. 720,000 & Higher LAZER Z ® LZ27K C604 MODEL ONL Y Place Model No. and Serial No. Label Here (Included in the Literature Pack) or Fill in Below Date Purchased Engine Model No. and Spec. No. Model No. Engine Serial No. (E/No) Serial No.
W ARNING CALIFORNIA Proposition 65 W ar ning The engine exhaust from this product contains chemicals known to the State of Califor nia to cause cancer, bir th defects, or other reproductive har m.
EXMARK P AR TS PLUS ® PROGRAM EFFECTIVE D A TE: September 1, 1995 Program If your Exmark dealer does not hav e the Exmark part in stock, Exmark will get the parts to the dealer the next b usiness day or the part will be FREE* Guaranteed!! How the Pr ogram W orks 1.
Introduction CONGRATULATIONS on the purc hase of y our Exmark Mo wer . This product has been carefully designed and man ufactured to gi v e you a maximum amount of dependability and years of trouble-free operation. This man ual contains operating, maintenance , adjustment, and safety instructions for y our Exmark mow er .
Contents Introduction .. . . .. . . .. . . .. .. . . .. . . .. . . .. .. . . .. . . .. . . .. .. . . .. . . .. . . .. .. . 4 Safety . . . .. . . .. . . .. . . .. .. . . .. . . .. . . .. .. . . .. . . .. . . .. .. . . .. . . .. . . .. .. . . .. . . .. 6 Safety Alert Symbol .
Safety Safety Safety Alert Symbol This Safety Alert Symbol (Figure 2) is used both in this manual and on the mac hine to identify important safety messages whic h m ust be follow ed to av oid accidents This symbol means: ATTENTION! BECOME ALERT! Y OUR SAFETY IS INV OL VED! Figure 2 1.
Safety DANGER In cer tain conditions gasoline is extremely ammable and v apors are explosi v e. A re or explosion from gasoline can bur n y ou, others, and cause proper ty damage. • Fill the fuel tank outdoors in an open area, when the engine is cold.
Safety Operation W ARNING Operating engine par ts, especially the mufer, become extremely hot. Sev ere bur ns can occur on contact and de bris, such as leav es, grass, brush, etc. can catch re. • Allow engine par ts, especially the muf er , to cool befor e touching .
Safety DANGER Operating on wet grass or steep slopes can cause sliding and loss of control. Wheels dropping ov er edges, ditches, steep banks, or w ater can cause rollo vers, which may result in serious injur y , death or drowning . • Do Not mo w slopes when grass is wet.
Safety Maintenance and Storage • Disengag e driv es , lo wer implement, set parking brake , stop engine and remo ve key or disconnect spark plug wire.
Safety Safety and Instructional Decals • Keep all safety signs legible . R emov e all grease, dirt and debris from safety signs and instructional labels . • R eplace all worn, damaged, or missing safety signs . • When replacement components are installed, be sure that current safety signs are afx ed to the replaced components .
Safety 1–633922 1–643222 1–643339 98-5954 103-1798 103–3270 103–4474 12.
Safety 103-4930 103-5881 103–6319 107-2102 107-21 12 13.
Safety 109-1214 109-1215 109-3148 109–7949 103–9255 14.
Specications Specications Model Numbers Serial Nos: 720,000 and Higher LZ27K C604 Systems Engine • Engine Specications: See your Engine Owner’ s Manual • RPM: Full Speed: 3750 ±50 RPM (No Load) Idle: 1500 RPM Fuel System • Capacity: 13.
Specications – Optional suspension seat: molded adjustable ip-up ar mrests . • Seat Safety Switc h: Incorporated into the Safety Interlock System. Time delay seat switc h eliminates rough ground cut-outs . Hydrostatic Ground Drive System • Hydrostatic Pumps: T w o Hydro Gear variable displacement piston pumps .
Product Overview Overall Height: Roll Bar - Up Roll Bar - Do wn 71.9 in. (182.6 cm) 53.8 inc hes (136.7 cm) T read Width: (Center to Center of Tires, W idthwise) Driv e Wheels 41.9 inc hes (106.4 cm) Caster Wheels 37.3 inches (94.7 cm) Wheel Base: (Center of Caster T ire to Center of Drive T ire) 53.
Operation Operation Note: Deter mine the left and right sides of the machine from the nor mal operating position. Controls Motion Control Levers The motion control levers located on eac h side of the console control the forward and rev erse motion of the machine .
Operation Drive Wheel Release V alves Located on the top right front corner of h y drostatic pumps . Driv e wheel release v alv es are used to release the hy drostatic dri ve system to allo w the machine to be pushed without the engine running . Unhook seat latch and tilt seat up to gain access to pumps .
Operation 4. Place the throttle midwa y between the “SLO W” and “F AST” positions . 5. On a cold engine , push the chok e lev er forw ard into the “ON” position. On a w ar m engine, leav e the chok e in the “OFF” position. 6. T urn ignition switc h to the “ST ART” position.
Operation When lev ers are centered in the T -slot the dri ve system is in the neutral position. With levers mov ed out in the T -slot the driv e system is in the neutral loc k position (Figure 6). Figure 6 1. Handles Out (Neutral Lock) 5. Neutral 2. Handles In (Neutral) 6.
Operation deck lift assist lever located at the front right corner of the oor pan. Note: When changing the cutting height positions, alw ays come to a complete stop and disengage the PTO . Figure 8 1. Lever in transport and 5 inch (12.7 cm) cutting height position 4.
Operation Figure 10 1. Spring disc washer (cone towards nut ) 3. 3/8 nyloc-torque to 30-35 ft-lb (41-47 N-m) 2. Front right anti-scalp bracket shown 4. 3/8-16 whizlock nut torque to 30-35 ft-lb (41-47 N-m) T ransporting T ransporting a Unit Use a heavy-duty trailer or truck to transpor t the machine .
Operation Important: Do Not attempt to tur n the unit while on the ramp, y ou may lose control and driv e of f the side. A v oid sudden acceleration when dri ving up a ramp and sudden deceleration when backing do wn a ramp . Both maneuvers can cause the unit to tip backw ard.
Maintenance Maintenance Note: Determine the left and right sides of the machine from the nor mal operating position. W ARNING While maintenance or adjustments are being made, someone could start the engine. Accidental star ting of the engine could seriously injure y ou or other bystanders.
Maintenance Maintenance Service Inter v al Maintenance Procedure Every 200 hours • Grease the brake brackets . Every 500 hours • Check the wheel hub slotted nut torque specications . • Check the wheel lug n uts . Monthly • Check the batter y charge.
Maintenance V oltage Reading Percent Charge Maximum Charger Settings Charging Inter v al 12.6 or g reater 100% 16 v olts/7 amps No Charging R equired 12.4 – 12.6 75–100% 16 volts/7 amps 30 Min utes 12.2 – 12.4 50–75% 16 v olts/7 amps 1 Hour 12.
Maintenance 1. Check starting circuit. Starter should crank with, parking brake engaged , PTO disengaged and motion control lev ers mov ed out in the neutral lock position.
Maintenance 6. Do Not w ash or use pressurized air to clean paper element or inner element. 7. R einstall elements . P osition the co ver so that the r ubber dust ejector is pointing downw ard and secure with retaining clips .
Maintenance Lubrication Char t Fitting Locations Initial Pumps Number of Places Ser vice Inter v al 1. Front Caster Wheel Hubs *0 2 *Y early 2. Front Caster Piv ots *0 2 *Y early 3. Height Adjustment Shaft Bearings 1 5 40 Hours 4. Deck Driv e Belt Idler Ar m 1 1 Y early 5.
Maintenance 4. R emov e one of the spacer nuts from the axle assembly in the caster wheel. Note that thread locking adhesiv e has been applied to loc k the spacer n uts to the axle . Remo ve the axle (with the other spacer nut still assembled to it) from the wheel assembly .
Maintenance Change Fuel Filter Service Interval: As required A fuel lter is installed betw een the fuel tanks and the engine. Replace when necessar y . Replacement Filters Kohler Kohler P/N 2405010 Change Hydraulic System Filter Service Interval: After the rst 250 hours Y early thereafter Note: Use only Exmark P art No .
Maintenance • Caster wheel spacer n uts . • Fuel tank bulkhead tting n uts . Adhesiv es suc h as “Loctite R C/609 or R C/680” or “F el-Pro Pro-Loc k R etaining I or R etaining II” are used on the following: Fuel tank studs , where studs are inserted into tank.
Maintenance all the chains is appro ximately equal. Mak e sure all chain attachment bolts are tight. R eposition anti-scalp rollers and tighten securely . Figure 14 1. Apply downward pressure here 2. Place locking pliers here to hold spring 3. 10 1/2 inches (26.
Maintenance Figure 16 1. Spring idler pulley 3. Right side idler pulley (adjustable) 2. Front of unit Deck Belt T ension Self-tensioning - No adjustment necessar y . Belt Guide Adjustment 1. Stop engine, w ait for all mo ving parts to stop , and remov e k ey .
Maintenance between the spring retainer brack et and the adjacent nyloc n ut. Tighten the jam nut abov e the trunnion roller . 4. If adjustment is necessary , loosen the n ut directly belo w the yok e.
Maintenance 1. This adjustment must be made with the driv e wheels tur ning . First raise the frame and block up so that dri v e wheels can rotate freely . 2. R emov e the electrical connection from the seat safety switch, located directly to the left of the seat switch assembly beside the h ydraulic oil reser v oir .
Maintenance Figure 22 1. Motion control bracket 2. Least resistance (softest feel) 3. Medium resistance (medium feel) 4. Most resistance (rmest feel) 5. T orque nyloc nut to 200 in-lb (16.7 ft-lb). Bolt must protrude past end of nyloc nut after torque.
Maintenance Cleaning Clean Engine Cooling System Service Interval: Before each use or daily (May be required more often in dry or dirty conditions.) CAUTION Excessi v e de bris around the engine cooli.
Maintenance F ederal la w states that batteries should not be placed in the garbag e . Management and disposal practices must be within relevant federal, state , or local la ws .
T roubleshooting T roubleshooting Important: It is essential that all operator safety mechanisms be connected and in proper operating condition prior to mow er use. When a problem occurs , do not o verlook the simple causes . F or example: star ting problems could be caused by an empty fuel tank.
T roubleshooting Problem Possible Cause Cor rectiv e Action 1. Engine load is ex cessive 1. R educe the ground speed. 2. Oil level in the crankcase is low . 2. Add oil to the crankcase . Engine overheats 3. Cooling ns and air passages for the engine are plug ged.
Schematics Schematics Electrical Diagram SEA T DELA Y MODULE DIODE 3. ST ART POSITION 1. OFF 2. RUN B + I + S CIRCUIT "MAKE" X + Y NONE B + I + A IGNITION SWITCH TERMINAL CONNECTIONS TER.
Schematics Hydraulic Diagram 44.
Conditions and Products Co vered Exmark Mfg. Co. Inc. and its aff iliate, Exmark W arranty Company , pursuant to an agreement between them, jointly warrant on the terms and conditions herein, that we .
Service Record Date: Description of W ork Done: Service Done By: 46.
47.
See Exmark’ s Complete Line of Accessories Riding Accessories Custom Ride Seat Suspension System Dec k Lift Assist Kit Hitch Kit Light Kit Micro-mulch System Roll Ov er Protection System (ROPS) Snow.
Een belangrijk punt na aankoop van elk apparaat Exmark LZ27KC604 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Exmark LZ27KC604 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Exmark LZ27KC604 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Exmark LZ27KC604 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Exmark LZ27KC604 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Exmark LZ27KC604 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Exmark LZ27KC604 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Exmark LZ27KC604 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
