Gebruiksaanwijzing /service van het product MTP 15 HD A van de fabrikant Extron electronic
Ga naar pagina of 26
User Guide MTP 15HD A Series T wisted Pair High Resolution Video and Serial Link MTP T ransmitters and Receivers 68-2206-01 Rev . B 03 13.
Safety Instructions • English W ARNING : This symbol, , when used on the product, is intended to alert the user of the presence of uninsulated danger ous voltage within the product’ s enclosure that may pr esent a risk of electric shock.
iii FCC Class A Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part15 of the FCC rules. The ClassA limits provide r easonable protection against harmful interfer ence when the equipment is operated in a commercial environment.
Conventions Used in this Guide Notifications The following notifications are used in this guide: W ARNING: A warning indicates a situation that has the potential to result in death or severe injury . A TTENTION: Attention indicates a situation that may damage or destroy the pr oduct or associated equipment.
Contents Introduction ............................................ 1 About this Guide .............................................. 1 About the MTP T ransmitters and Receivers ..... 2 T wisted Pair Cable Advantages .................... 2 T ransmission Distance .
Intr oduction This section gives an overview of the user guide. This section also describes the MTP 15HD A Series of transmitters and receivers. Cover ed topics are: • About this Guide • About the.
About the MTP T ransmitters and Receivers The Extron MTP T 15HD A transmitter and MTP RL 15HD A and MTP RL 15HD A SEQ receivers ar e a system for long-distance distribution of VGA or other high resolution video and audio.
T ransmission Distance The maximum distance is determined by the frequency and r esolution of the signal that is input to the transmitter . The table on page 4 specifies the recommended maximum trans.
Video Format Pre- Peak off Pre-Peak on Max. distance (high quality) Max. distance (variable quality) Composite, S-video, Component 800' (245 m) 1000' (300 m) 640 x 480 <300' (90 m) &.
Installation and Operation This section provides information on: • Installation Overview • Front Panel Featur es • T ransmitter Rear Panel Features • Receiver Rear Panel Features • Power Sup.
Fr ont Panel Features See figure 2 to identify the fr ont panel features on the transmitter and r eceiver . MTP RL 15HD A Receiver MTP SERIES MTP RL 15HD A SEQ Receiver RGB PEAKING LEVEL RGB DELA Y P.
e EDID select rotary switch — The r otary switch is used to select specific pre-pr ogrammed or user -recor ded EDID settings. Position 0 of this 16 position rotary switch is used to select the user recor ded EDID. Position F passes the EDID from the display connected to the loop-out back to the input.
k DIP switches (RL receivers only) — A 5-pole DIP switch is used to configur e the features of the MTP r eceivers. • • Horizontal sync (H Sync +) switch — Set this switch On (up) for positive horizontal sync or Off (down) for negative sync.
T ransmitter Rear Panel Featur es Figure 3 shows an MTP T 15HD A transmitter , which has all of the connectors and other features that ar e on either transmitter in the MTP 15HD A series.
d Audio input connector — Plug a 3.5 mm stereo audio plug into this connector for unbalanced audio input. Wire the plug as shown in figure 5. The ster eo audio input is summed and output on the twisted pair cable as mono audio. Slee ve ( ) Ring Right ( - ) Tip Left (+) Figure 5.
Receiver Rear Panel Featur es Figure 6 shows an MTP RL 15HD A r eceiver , which has all of the connectors and other features that ar e on either receiver in the MTP 15HD A series. MTP RL 15HD A Receiver NOTE: A “C7” label is affixed to transmitters designed for STP201 or CA T 7 cable.
Power Supply W iring and Grounding Figure 8 shows how to wir e and ground the connector . A TTENTION: • Potential damage to property . Power supply voltage polarity is critical. Incorrect voltage polarity can damage the power supply and the transmitter or receiver .
A TTENTION: • Potential damage to property . This product is intended to be supplied by a Listed Power Unit marked "Class 2" or "LPS", rated 12 VDC, maximum 1.
T wisted Pair Cable T ermination Figure 9 details the r ecommended termination of twisted pair cables with RJ-45 connectors in accordance with the TIA/EIA T568A or TIA/EIA T568B wiring standar ds. Y ou can use either standard with CA T 5, 5e, 6, 7, and STP201 cable, but ensure that you use the same standard on both ends of the cable .
Skew Delay Compensation CA T 5, 5e, 6, 7, and STP201 cable can lead to registration errors between the Red, Gr een, and Blue video signals. Pair skew can be measured with test equipment or identified.
EDID Conguration The MTP 15HD A transmitter can either recor d EDID from a display device, or a pre-pr ogrammed EDID can be selected using the rotary and DIP switches. Recording a Display EDID 1. T urn the rotary switch to position 0. NOTE: The vertical frequency DIP switch has no ef fect in this mode.
Refer ence Information This section provides information about: • Part Numbers, Optional Accessories, Cables, and Connectors Part Numbers, Optional Accessories, Cables, and Connectors Part Numbers M.
Cables NOTE: Extron Enhanced Skew-Fr ee A V UTP cables are not r ecommended for Ether net or LAN applications. Description Part Number VGA connector cable 26-238-xx SYM BNC Female Mini High Resolution.
Mounting This section outlines the various mounting options available for the MTP 15HD A Series transmitters and receivers: • T abletop Placement • Under -Desk Mounting • Rack Mounting • Projector Mounting T abletop Placement Attach the four provided rubber feet to the bottom of the unit and place it in any convenient location.
Rack Mounting Procedur e These units can be mounted on any of these optional rack systems, including: • RSF 123: 3.5 inch deep, 1U rack shelf kit (part number 60-190-20) • RSB 123: 3.
Extron Headquarters +1.800.633.9876 (Inside USA/Canada Only) Extron USA - W est Extron USA - East +1.714.491.1500 +1.919.850.1000 +1.714.491.1517 F AX +1.919.850.1001 F AX Extron Europe +800.3987.6673 (Inside Europe Only) +31.33.453.4040 +31.33.453.4050 F AX Extron Asia +800.
Een belangrijk punt na aankoop van elk apparaat Extron electronic MTP 15 HD A (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Extron electronic MTP 15 HD A heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Extron electronic MTP 15 HD A vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Extron electronic MTP 15 HD A leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Extron electronic MTP 15 HD A krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Extron electronic MTP 15 HD A bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Extron electronic MTP 15 HD A kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Extron electronic MTP 15 HD A . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
