Gebruiksaanwijzing /service van het product DD602 van de fabrikant Fisher & Paykel
Ga naar pagina of 24
DD602 (Prefinished) DD602 I (Integrated) Models DD602 DD602 I Part No. 599065/D USA.
Table of Contents Section 1 General Information 1.1 Preparation 1.2 Product Specifications & Cavity Dimensions 1.3 Options for Installing Multiple Products 1.4 Electrical, Plumbing & Drainage Information 1.5 Product Parts 1.6 Additional Product Parts for Integrated DishDrawer Section 2 Foot Slide Retainer Information 2.
Electrical 110-120 VAC 3 pin socket outlet Drying Residual Heat & Fan Assisted Water Connection Recommended Hot 140 ° F Max. (60 ° C) Water Pressure Maximum 139 p.s.i. (960 kpa) Minimum 4.3 p.s.i. (30 kpa) GENERAL INFORMATION The DishDrawer MUST be installed to allow for future removal from the enclosure if service is required.
Page DD_03 Where the DishDrawer is installed under a counter top, it is recommended that bare wood surrounding the DishDrawer is sealed with an oil based paint or polyurethane to prevent possible steam damage. Ensure the cavity sides are plumb (vertical) as this will assist with leveling the DishDrawer.
Page DD_04 PLUMBING - DRAINAGE OPTIONS Note: Prefinished Model is shown. There is no variation in plumbing between Prefinished products and Integrated products. Options 1 and 2 are the most preferred options. Option 1 Option 2 Option 3 Improper connection of the equipment-grounding conductor can result in a risk of electric shock.
Page DD_05 TOOLS NEEDED TO INSTALL DISHDRAWER Wooden Chopping Board Level Safety Glasses Utility Knife Pencil Drill & Drill Bits ( 3 / 32 ", 9 / 16 " & 11 / 32 ") or (2.
Page DD_06 SECTION 2 FOOT SLIDE RETAINER INFORMATION STEP 2.1 ASSEMBLING THE FOOT SLIDE RETAINER It is important that the Foot Slide Retainer is correctly installed. It guides the feet back and holds the rear of the DishDrawer down to prevent it rocking forward when the drawers are opened.
2.1.5 Position the Foot Slide Retainer within the cutout areas of the Template. 2.1.6 The Template should be placed in the cavity until the wings just touch the existing cabinetry. This ensures the front of the DishDrawer will be flush with the existing cabinetry.
Page DD_08 3.1.1 Feed the Power Cord, Inlet Hose and Drain Hoses through the Services Hole. Position the DishDrawer in front of the opening. 3.1.2 Connect the Inlet Hose to the HOT WATER SUPPLY. Ensure sealing washer supplied with the accessories is fitted.
Page DD_09 3.1.8 Ensure there is a power outlet in reach of the supplied flex. If there is not a suitable outlet available then have one installed by a qualified electrician. DO NOT modify the power plug supplied with the DishDrawer or use an extension cord, adaptor plug or multiple outlet box.
Page DD_10 The DishDrawer should not support any part of the kitchen cabinets. WARNING The DishDrawer must be levelled so that each corner is at least within 1 / 8 (3mm) of level. IMPORTANT TIP Each turn of the foot adjusts by 3 / 64 (1.25mm).
Page DD_11 3.5.1 Partially lift the top mounting tabs by inserting a flat screwdriver into the Vee shaped slot. Complete the folding process by bending about the rows of oval slots so that the tab is approximately level and parallel with the underside of the bench.
Page DD_12 SECTION 4 PREFINISHED TOE KICK INSTALLATION STEP 4.1 SETTING THE UPPER TOE KICK HEIGHT 4.1.1 Remove the Upper Toe Kick by opening the bottom drawer, then holding the Toe Kick at the base, pull outwards to unclip and rotate up.
Page DD_13 Ensure the Toe Kick Pins are positioned on a wooden chopping board to avoid damage to surrounding area. IMPORTANT STEP 4.3 TRIMMING THE TOE KICK PINS Before cutting the Lower Toe Kick, ensure the Toe Kick is positioned on a wooden chopping board to avoid damage to surrounding area.
Page DD_14 4.3.3 If the height of the Lower Toe Kick is greater than 1 1 / 4 " (32mm) , insert the Toe Kick Brace in between the two lowest ribs of the Lower Toe Kick. 4.3.4 Insert the Toe Kick Pins into the Lower Toe Kick. These will hold the Brace in place.
STEP 5.1 INTEGRATED DRAWER FRONT & TOE KICK DIMENSIONS 5.1.1 Use the following diagrams to work out the dimensions for the Integrated Panels for Drawer Fronts and Toe Kicks.. I N T E G R A T E D P R O D U C T O N L Y IMPORTANT Allow for any obstructions at the top of the cavity when allowing for space between the countertop and DishDrawer.
I N T E G R A T E D P R O D U C T O N L Y IMPORTANT Check top and bottom measurements of cavity and use the smaller dimension to ensure that the drawer fronts and toe kicks will fit. Page DD_16 Drawer Front Air Flow Chamfer Chamfer the back of the Drawer Front Panel at the bottom as shown, to enhance airflow.
Accuracy is essential when cutting the Badge Mounting Hole to ensure a neat fit to hold the badge. IMPORTANT IMPORTANT All marking out should be done on the back surface of the Drawer Front. 5.1.3 Badge Cutout Dimensions Cut out Badge Mounting Hole in the chosen position (see Control Badge Mounting Zone on diagram above).
5.1.4 Drawer Front Mounting Bracket Nut Holes Using a 11 / 32 (8.5mm) diameter drill bit, drill out the four screw holes in each door panel to a depth of 9 / 16 (14mm). Remove burrs. At least 5 / 8 (16mm) of Drawer Front material is required for the Drawer Mounting Nuts (M6 screw in nut - Type E).
STEP 6.2 DISASSEMBLING THE INTEGRATED BADGE SECTION 6 STEP 6.1 CHANGING THE INTEGRATED BADGE ENCLOSURE There are several different colored Integrated badges to choose from. They include black, chrome, satin & brass. Two color options are provided with your machine, other options are available from your local Dealer.
WARNING CAUTION Take care not to damage front surface of panel. Ensure all cuts are straight and care is taken to avoid damage to the Drawer Front. Care should be taken in the following steps. Overtightening will damage the Drawer Front. CAUTION I N T E G R A T E D P R O D U C T O N L Y STEP 6.
I N T E G R A T E D P R O D U C T O N L Y Use a small amount of liquid soap along the lip of the seal to assist the Drawer Front to slide on easily against the seal.
I N T E G R A T E D P R O D U C T O N L Y DISHDRAWER TOE KICK INFORMATION SECTION 7 Upper Toe Kick 7.1.1 Remove Plastic Toe Kick from product. Unscrew metal back panel. 7.1.2 Place customer supplied Upper Toe Kick face down on soft surface. Locate metal back panel on rear of Toe Kick (ensure the bottom of Toe Kick and panel are flush and centered).
SECTION 8 LEAVE ALL LITERATURE WITH THE CUSTOMER. Water underneath DishDrawer; check the hose connections and hose for leaks. Water around water supply and drainage connections - check connections, existing plumbing and hoses for leaks.
Een belangrijk punt na aankoop van elk apparaat Fisher & Paykel DD602 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Fisher & Paykel DD602 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Fisher & Paykel DD602 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Fisher & Paykel DD602 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Fisher & Paykel DD602 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Fisher & Paykel DD602 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Fisher & Paykel DD602 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Fisher & Paykel DD602 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
