Gebruiksaanwijzing /service van het product M-96 van de fabrikant Fisher
Ga naar pagina of 18
M-96 Operating Manual Value, Pedestal and Box Locator FISHER RESEARCH LABORATORY.
CONTENTS About Your M-96 ..................................................................... pg. 1 Condensed Operating Instructions ...................................... pg. 2 Factory Preset ‘Turn-On-and-Go’ Marks .......................... pg.
ABOUT YOUR DETECTOR 1 The Fisher M-Scope Model-96 offers the utility industry an uncomplicated detector for finding paved-over or buried metallic objects. The waterproof search coil and the rugged electronics housing make the M-96 an ideal detector for field utility use.
2 FACTORY PRESET ‘TURN-ON-AND-GO’ MARKS Your Fisher M-96 is fairly simple to operate, especially when compared to other metal detectors. Even so, we strongly recommend that you read this entire manual. You’ll be able to tune your M-96 to your specific needs and conditions.
3 5. With the stem length properly adjusted, wrap the search coil cable snugly around the lower stem and the upper handle. Leave just enough slack near the coil to allow it to be tilted completely backward and forward.
4 7. With the shaft length and coil angle properly adjusted, you should be able to move into your search position by leaning forward very slightly and raising your arm. 8. If the arm rest is too wide or narrow, you may bend it slightly inward or outward to your exact requirements.
5 10. The two knobs can be adjusted with your thumb without removing your hand from the grip, particularly if you’re right handed. Set the controls of the MODE and GROUND switches to the red preset marks: NORMAL for the MODE control and 5 for the Ground control.
6 FITTING THE DETECTOR TO THE OPERATOR 1. Start by gripping the foam hand grip and letting your arm hang comfortably by your side. 2. The length of the handle shaft and the angle of the search coil are both adjustable. Adjust the search coil angle so that it is parallel to the ground.
7 NORMAL MODE The NORMAL MODE of operation is generally used when searching for larger objects, such as manhole covers, telephone pedestals in the snow and valve boxes. The NORMAL MODE, which is marked in red, is also used for locating smaller, shallower objects.
8 HIGH MODE 1. Rest the search coil on the ground in an area you are reasonably sure is free of metal objects. 2. After going through BAT test in the NORMAL MODE, turn the MODE knob to HIGH. 3. Turn the GROUND knob to 5. 4. Push and releases the RETUNE button.
9 CONTROL PANEL On/Off GROUND Knob The ON/OFF GROUND Rejection Knob, when turned fully counterclockwise, clicks into the off position, turning the detector off.
10 HEADPHONES Jack The HEADPHONES Jack is located to the right of the RETUNE Button. A plastic plug can be inserted into this jack to keep dirt and water out when not in use. It’s a good idea to establish a systematic search pattern for your selected area.
11 HELPFUL HINTS Raising the coil vertically in the air is another method of reducing the target size (as seen by the detector) and pinpointing the target. Because the area of greatest sensitivity is in the center of the search coil, it isvery easy to pinpoint the location of any metallic object, large or small.
12 PINPOINTING Accurate pinpointing with the M-96 takes some practice but not much. With a little experience, you should be able to pinpoint buried targets in just a few seconds.
13 CHANGING BATTERIES To change the batteries, slide the side covers on the battery housing located underneath the arm rest in the direction of the arrows. Remove the battery holders one at a time. Replace all 6 AA cells, making sure that each one is inserted with polarity (+ or -) in the same direction as the ones you remove.
14 Operating Environment +33° F to +120° F (0 to 50° C) ................ with carbon zinc batteries -4° F to +120° F (-20 to 50° C) ....................... with alkaline batteries Search coil submersible in water Operating Frequency of Search Coil .
15.
QUALITY Fisher detectors are renowned for their quality. Each instrument is hand crafted in the USA with pride PERFORMANCE Our detectors are durable, dependable, and search deeper. REPUTATION Fisher produced the first patented metal detector in 1931. For over 70 years, the Fisher logo has been a mark of excellence.
Een belangrijk punt na aankoop van elk apparaat Fisher M-96 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Fisher M-96 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Fisher M-96 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Fisher M-96 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Fisher M-96 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Fisher M-96 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Fisher M-96 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Fisher M-96 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
