Gebruiksaanwijzing /service van het product G4815 van de fabrikant Fisher-Price
Ga naar pagina of 16
G4815 Instructions Bounce ‘n Go ™ Coupe Please read these instructions carefully and identify all parts before assembly . Refer to the parts and fasteners pages for identification. Keep this instruction sheet for future reference, as it contains important information.
2 Parts Handle/Canopy Notes: • Some parts shown are assembled to both sides of the coupe. • Please save all packaging material until assembly is complete to ensure that no parts are discarded. • Please wipe each part with a clean, dry cloth before assembling this product.
3 W arning and Caution CA UTION W ARNING T o av oid serious injury: • Adult supervision required. • Never use near cars and other motor vehi- cles, near streets, steps, sloped driveways, hills, roadways, alleys, swimming pools, or other bodies of water .
4 1 • Place the frame upside down on a flat surface. Make sure the steering linkage assembly is fitted to the front end of the frame. • Remove the tape holding the front axles to the frame. Rotate the front axles out. 2 • Push the front axles down into the groove in each end of the steering linkage.
5 5 • Fit an axle cover over the cap nuts and to the front end of the frame. Push down on the axle covers to “snap” them into place. Hint: Y ou may need to carefully tap the axle covers with a hammer to secure in place. Axle Covers 6 • Slide a 5 / 16 " washer onto a front axle.
6 9 • Fit a .354" cap nut onto the end of the front axle. • Cover the cap nut with the assembly tool. T ap the cap nut assembly tool with a hammer to secure the cap nut to the front axle. • Pull on the small, front wheel to be sure it is secure on the front axle.
7 13 • Slide the smooth end of the rear axle into the hole in one side of the bouncer base/spoiler , a frame bushing, the frame, the other frame bushing and out through the hole in the other side of the bouncer base/spoiler .
8 17 • Fit an axle cover to the large, rear wheel, as shown. • Push the axle cover to “snap” it into place. Hint: Y ou may need to carefully tap the axle cover with a hammer to secure in place. • Repeat assembly steps 13-17 to assemble an axle bushing, large, rear wheel, wheel bushing, .
9 Assembly 21 • Lift the front end of the vehicle. • Insert the straight end of the steering column up through the hole in the frame. 23 • Fit the steering wheel onto the turn signal and the steering column. 24 • Fit a .354" cap nut onto the end of the steering column.
10 26 • Fit the sound box inside the center of the steering wheel. Assembly 27 • Fit the top edge of the sound box cover into the groove in the steering wheel. • “Snap” the sound box cover into the center of the steering wheel. Sound Box Sound Box Cover • Loosen the screws in the sound box battery compartment door .
11 Assembly 30 • Insert the upper post into the lower post. 31 • Fit the grip halves to the post assembly , over the latch halves. • Insert three #6 x 1 / 2 " screws into the grip halves to join all three parts together . Tighten the screws.
12 32 • Position the post so that the lower bend is toward the front end of the coupe. • Insert the post into the column on the back of the coupe. 33 • Insert the #10 x 2 1 / 8 " bolt into the column on the back of the coupe. • Tighten the bolt.
13 Seat Adjustment • Place the seat onto the coupe into either of two positions – front or back . • Have your child sit on the seat and check the distance between your child’s feet and the pedals. Now , move the seat closer to or further from the pedals .
14 • Locate the sliding latches inside the bouncing base/spoiler . While lifting both sliding latches on the bouncing base/spoiler , rotate the bouncing base/spoiler down . Continue to rotate the bouncing base/spoiler down until it “snaps” into place.
15 • Locate the sliding latches inside the bouncing base/spoiler . While pushing both sliding latches on the bouncing base/spoiler down , rotate the bouncing base/spoiler up . Continue to rotate the bouncing base/spoiler up until it “snaps” into place.
Care • Wipe this toy with a clean cloth dampened with a mild soap and water solution. Do not immerse this toy . • Do not leave this toy outside in the rain. W ater inside the soundbox could cause it to malfunction. • This toy has no consumer replaceable parts.
Een belangrijk punt na aankoop van elk apparaat Fisher-Price G4815 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Fisher-Price G4815 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Fisher-Price G4815 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Fisher-Price G4815 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Fisher-Price G4815 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Fisher-Price G4815 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Fisher-Price G4815 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Fisher-Price G4815 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
