Gebruiksaanwijzing /service van het product Jerry Douglas Signature Series van de fabrikant Fishman
Ga naar pagina of 20
USER GUIDE JERR Y DOUGLAS SIGNA TURE SERIES A URA ® IMAGING PEDAL.
2 Quick start Power – Install a 9V alkaline or lithium battery (not included). Set the controls – V olume at minimum, select at #1 and blend at its mid-point. Plug in – Use standard ¼-inch shielded instrument cables. Place any other pedals after the Aura.
3 ® ACOUSTIC IMAGING.
4 About this pedal Larry Fishman developed the Signature Series Aura Pedal with a world-class team of professionals, including musician Jerry Douglas, r ecording studio engi- neer Bil V ornDick, and reknowned r esonator builder Paul Beard, to bring you the most realistic amplifi ed tone available.
5 A word from Paul Beard “In the world of resophonic guitar amplifi cation, we fi nally have resolution! The Fishman Nashville Series resophonic pickup is the r esult of new technology and innovative design. Use this pickup when playing with the Aura Imaging Pedal, select a microphone Image and turn it up.
6 Images Image Microphone T ype Distance 1 Neumann U67 Large diaphragm tube condensor 12” 2 Neumann U67 Large diaphragm tube condensor 18” 3 RCA 77 Poly-directional ribbon 12” 4 RCA 77 Poly-dire.
7 Image Microphone T ype Distance 9 Royer R-121 Figure 8 Ribbon 12” (Instrument drop tuned to CAFCAF) 10 Neumann U47 Lg. diaphragm cardioid tube condensor 12” 11 Neumann FET 47 Cardioid FET Lg. diaphragm condensor 12” 12 Neumann FET 47 Cardioid FET Lg.
8 Using effects When using your Aura Imaging Pedal with other effects devices, place the Aura Imaging Pedal fi rst in the chain after your guitar . ® ACOUSTIC IMAGING.
9 If you have a pedal tuner , place it before the Aura Imaging Pedal. ® ACOUSTIC IMAGING.
10 Left side panel Output Use a standard ¼-inch instrument cable to connect the output to your amplifi er , mixer or effects devices. Y ou can also connect this output to an unbalanced input on a recor ding system.
11 Right side panel Input Plug in your guitar here with a standar d ¼-inch instrument cable. If you have a passive undersaddle pickup (no battery onboard), always plug into the Aura Imaging Pedal fi rst, even if you use a pedal tuner . Tr i m Raise or lower the trim to optimize the input level for your pickup.
12 Control set Phase switch Use the phase switch to improve bass r esponse at low volume or to control feedback at high volume. Play your guitar and toggle the phase switch back and forth until you achieve the desired r esult. V olume For the cleanest signal, set the volume as high as possible without clipping the next device in the signal chain.
13 Select The 16 Images you can choose with the select knob are hand picked for your type of guitar . T ry all 16 and pick the ones that compliment your playing style and sound good in the room. For example, dark/deep sounding Images may add impact to a solo performance.
14 Blend (continued) Suggestions • T o fi nd a good mix of Image and pickup, turn the blend knob to about 8 o’clock, then step on the footswitch. Compare the Image/ pickup mix to the dry pickup signal. Slowly move blend clockwise and then switch between the two until you are happy with the Image/pickup blend.
15 F ootswitch Step on the footswitch to bypass the Aura effect. When you stomp, you’ll hear the dramatic differ ence between the Image blend and the dry pickup. When the light above the footswitch is on, the Image is active. Note when the effect is bypassed, your guitar signal remains buf fered.
16 Power Power may be supplied by either a 9V battery ( battery compartment under pedal ) or an approved 9V adapter . Insert a plug into the input jack, and the Aura Imaging Pedal powers up. T o conserve the battery , r emove the plug fr om the input when not in use.
17 Battery replacement The clip/batt indicator will light steadily when it is time to change the battery . Open the battery door underneath the pedal and install a fresh 9V alkaline or lithium battery . When the clip/batt LED comes on you have approximately one hour of remaining battery life.
18 Specifi cations Digital signal path: A/D, D/A conversion: 24-bit Signal processing: 32-bit Power supply: 9V alkaline battery or 9VDC adapter T ypical in-use curr ent consumption: 18mA T ypical 9V .
19.
www .fi shman.com 513-300-146 Rev A 6-07.
Een belangrijk punt na aankoop van elk apparaat Fishman Jerry Douglas Signature Series (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Fishman Jerry Douglas Signature Series heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Fishman Jerry Douglas Signature Series vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Fishman Jerry Douglas Signature Series leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Fishman Jerry Douglas Signature Series krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Fishman Jerry Douglas Signature Series bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Fishman Jerry Douglas Signature Series kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Fishman Jerry Douglas Signature Series . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
