Gebruiksaanwijzing /service van het product 1998 Taurus van de fabrikant Ford
Ga naar pagina of 216
Before driving Introduction 2 Instrumentation 4 Controls and features 20 Seating and safety restraints 60 Starting and driving Starting 92 Driving 98 Roadside emergencies 127 Servicing Maintenance and care 150 Capacities and specifications 200 Reporting safety defects 207 Index 208 All rights reserved.
ICONS Indicates a warning. Read the following section on W arnings for a full explanation. Indicates vehicle information related to recycling and other environmental concerns will follow . Correct vehicle usage and the authorized disposal of waste cleaning and lubrication materials are significant steps towards protecting the environment.
contents without notice and without incurring obligation. SPECIAL NOTICES Using your vehicle as a snowplow Do not use this vehicle for snowplowing. Using your vehicle as an ambulance Do not use this vehicle as an ambulance. Y our vehicle is not equipped with the Ford Ambulance Preparation package.
10 H C 20 30 40 50 60 70 80 90 100 0 0 RPMx1000 F 20•km/h LOW FUEL 40• 60 80 100 120 • • • • •140 • 1 2 3 4 5 CHECK ENGINE 4 X 4 THEFT 6 E 18 8 H L ABS + - + - 0000 000 05 0 P SRS ON OFF RES SET ACCEL COAST Headlamp control (pg. 20) T urn signal and wiper/washer control (pg.
VOL-PUSH ON AM FM BASS TREB BAL FADE AUTO SET SEEK TUNE DISCS SCAN EJ TAPE CD DOLBY 8 NR REW 1 FF 2 SIDE 1-2 3 4 COMP 5 SHUFFLE 6 ST FM 1 FM 1 FLOOR PANEL LO HI COOL WARM DEF FLR& DEF PANEL & FLOOR OFF 4H 2H A4WD 4L HI COOL WARM OFF P ANEL FLOOR DEF FLR & DEF P ANEL & FLOOR LO 4WD Control (pg.
W ARNING LIGHTS AND CHIMES Low fuel Illuminates when the fuel level is low . The lamp will also illuminate when the ignition key is turned to ON and the engine is off. Check engine Y our vehicle is equipped with a computer that monitors the engine’ s emission control system.
the engine is started, one of the engine’ s emission control systems may be malfunctioning. The light may illuminate without a driveability concern being noted.
If the Check Engine light remains on, have your vehicle serviced at the first available opportunity . Light is blinking: Engine misfire is occurring which could damage your catalytic converter . Y ou should drive in a moderate fashion (avoid heavy acceleration and deceleration) and have your vehicle serviced at the first available opportunity .
Brake system warning Momentarily illuminates when the ignition is turned on and the engine is off. Also illuminates when the parking brake is engaged. Illumination after releasing the parking brake indicates low brake fluid level. Anti-lock brake system (ABS) Momentarily illuminates when the ignition is turned on and the engine is off.
SecuriLock Y anti-theft system This light indicates the anti-theft alarm system is armed. Refer to Anti-theft system in the Controls and features chapter . Momentarily illuminates when the ignition is turned to ON/ST ART . If the light fails to illuminate, continues to flash or remains on, have the system serviced.
oil pressure gauge in this chapter for more information. Four wheel drive low (if equipped) Illuminates when four -wheel drive low is selected. Four wheel drive indicator (if equipped) Illuminates when 4x4 range is selected. Automatic four wheel drive indicator (if equipped) Illuminates when A4WD (automatic 4–wheel drive) is engaged.
Low washer fluid Illuminates when the ignition is turned to ON and when the windshield washer fluid is low . Door ajar Illuminates when the ignition switch is in the ON or ST ART position and any door is open. Fuel reset Illuminates when the ignition key is turned to the ON position and the fuel pump shut-off switch has been triggered.
Key-in-ignition warning chime Sounds when the key is left in the ignition in the OFF/LOCK or ACC position and either front door is opened. Headlamps on warning chime Sounds when the headlamps or parking lamps are on, the ignition is off (and the key is not in the ignition) and either front door is opened.
than the advertised capacity due to the reserve fuel. Speedometer Indicates the current vehicle speed. Engine coolant temperature gauge Indicates the temperature of the engine coolant. At normal operating temperature, the needle remains within the normal area (the area between the “H” and “C”).
Odometer Registers the total kilometers (miles) of the vehicle. T rip odometer Registers the kilometers (miles) of individual journeys. T o reset, depress the control. T achometer Indicates the engine speed in revolutions per minute. Driving with your tachometer pointer continuously at the top of the scale may damage the engine.
Battery voltage gauge This gauge shows the battery voltage when the ignition is in the ON position. If the pointer moves and stays outside the normal operating range (as indicated), have the vehicle’ s electrical system checked as soon as possible. Engine oil pressure gauge This shows the engine oil pressure in the system.
depending on your vehicle’ s option package, but the functions are the same. The trip computer only works when the ignition is in the ON position. T rip computer features follow: Selectable features English/metric display Press this control to change the trip computer display from metric to English units.
2. if the vehicle is started while parked on an incline. 3. if less than 30 liters (8 gallons) of fuel is added to the fuel tank. The fuel range function will flash for 5 seconds when you have approximately the following amounts of fuel left before you run out: • 80 km (50 miles) • 40 km (25 miles) • 16 km (10 miles) A verage fuel economy .
Press the MODE control one final time to turn the trip computer display off. RESET E/M MODE MILES TO EMPTY Instrumentation 19.
HEADLAMP CONTROL Rotate the headlamp control to the desired position: — OFF . — Parking lamps on. — Headlamps on. Foglamp control (if equipped) The headlamp control also operates the foglamps. The foglamps can be turned on only when the headlamps are in the position.
The Daytime Running Light (DRL) system will not illuminate the tail lamps and parking lamps. T urn on your headlamps at dusk. Failure to do so may result in a collision. P ANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel during headlight and parklamp operation.
• T o turn autolamps off, rotate the control down until it clicks. • A small LED illuminates next to the autolamp control to indicate that the headlamps have been turned on by the autolamps. • Foglamps are not controlled by the autolamps. In order to turn on the foglamps, you must turn the lamp switch to the position and pull for fog.
4WD CONTROL (IF EQUIPPED) This control operates the Control-T rac 4WD. Refer to Control trac automatic four -wheel drive system in the Driving chapter for more information. AUDIO SYSTEM Refer to the “Audio Guide” for instructions on how to operate the audio system.
Mode selector control Controls the direction of the airflow to the inside of the vehicle. The air conditioning compressor will operate in all modes except P ANEL and FLOOR. However , the air conditioning will only function if the outside temperature is about 10°C (50°F) or above.
vehicle. It is quieter than MAX A/C but not as economical. Airflow will be from the instrument panel registers. • P ANEL-Distributes outside air through the instrument panel registers. However , the air will not be cooled below the outside temperature because the air conditioning does not operate in this mode.
• FLR & DEF-Distributes outside air through the windshield defroster ducts and the floor ducts. Heating and air conditioning capabilities are provided in this mode. For added customer comfort, the air distributed through the floor ducts will be slightly warmer than the air sent to the windshield defroster ducts.
• Remove any snow , ice or leaves from the air intake area (at the bottom of the windshield under the hood). • If your vehicle has been parked with the windows closed during hot weather , the air conditioner will do a much faster job of cooling if you drive for two or three minutes with the windows open.
Rear console climate controls (if equipped) Depending on the equipment package of your vehicle, the rear console may not be equipped with rear console audio/climate controls.
Select for air to flow through these vents: Auxiliary A/C-heater controls (if equipped) The auxiliary A/C-heater feature provides increased capacity to quickly heat or cool the vehicle.
In order for the auxiliary A/C-heater controls to function, the driver’ s auxiliary A/C-heater control must be set to REAR. The instrument panel climate controls must be on in order for the auxiliary A/C-heater to operate.
T urn the temperature control to the desired temperature. Y ou can get warm or cool air through either the overhead registers or floor vent by turning the auxiliary mode selector: • Far left for airflow to the overhead registers. • Far right for airflow to the rear floor vent.
POSITIONS OF THE IGNITION 1. ACCESSORY , allows the electrical accessories such as the radio to operate while the engine is not running. 2. LOCK, locks the steering wheel, automatic transmission gearshift lever and allows key removal. 3. OFF , shuts off the engine and all accessories without locking the steering wheel.
SPEED CONTROL T o turn speed control on • Press ON. V ehicle speed cannot be controlled until the vehicle is traveling at or above 48 km/h (30 mph). Do not use the speed control in heavy traffic or on roads that are winding, slippery , or unpaved. Do not shift the gearshift lever into N (Neutral) with the speed control on.
T o set a speed • Press SET ACC/SET ACCEL. For speed control to operate, the speed control must be ON and the vehicle speed must be greater than 48 km/h (30 mph). If you drive up or down a steep hill, your vehicle speed may vary momentarily slower or faster than the set speed.
T o set a higher set speed • Press and hold SET ACC/SET ACCEL. Release the control when the desired vehicle speed is reached or • Press and release SET ACC/SET ACCEL. Each press will increase the set speed by 1.6 km/h (1 mph) or • Accelerate with your accelerator pedal, then press and release SET ACC/SET ACCEL.
• Depress the brake pedal. When the desired vehicle speed is reached, press SET ACC/SET ACCEL. T o disengage speed control • Depress the brake pedal. Disengaging the speed control will not erase the previously programmed set speed. Pressing OFF will erase the previously programmed set speed.
T o return to a previously set speed • Press RES/RSM/RESUME. For RES/RSM/RESUME to operate, the vehicle speed must be faster than 48 km/h (30 mph). TILT STEERING Pull the tilt steering control toward you to move the steering wheel up or down. Hold the control while adjusting the wheel to the desired position, then release the control.
HAZARD FLASHER For information on the hazard flasher control, refer to Hazard lights control in the Roadside emergencies chapter . WINDSHIELD WIPER/WASHER CONTROLS Rotate the windshield wiper control to the desired interval, low or high speed position.
I N T1—T e n second interval rear wiper . OFF — Rear wiper and washer off. Speed dependent wipers When the windshield wiper control is set on the intermittent settings, speed-sensitive front wipers automatically adjust as the vehicle’ s speed increases.
Deactivating overdrive Press the transmission control at the end of the gearshift lever . The transmission control indicator light TCIL (OFF) will illuminate on the end of the gearshift lever The transmission will operate in gears one through three. T o return to normal overdrive mode, press the transmission control again.
Installing a garage door opener (if equipped) The storage compartment can be converted to accommodate a variety of aftermarket garage door openers: • Place V elcro y hook onto back side of aftermarket transmitter opposite of actuator control. • Place transmitter into storage compartment, control down.
One-touch moon roof (if equipped) • Press and release the rear portion of the moon roof control to open. • Press and hold (as desired) the front portion of the moon roof control to close. • T o halt motion at any point during one-touch opening, press the control a second time.
Usually , when something affects the compass readings, the compass will correct itself after a few days of operating your vehicle in normal conditions. If the compass still appears to be inaccurate, a manual calibration may be necessary . Refer to Compass calibration adjustment .
2. Locate the compass module mounted at the base of the mirror . 3. T urn ignition to the ON position. 4. Insert an appropriate diameter rod (paperclip) into the small hole underneath the compass module and gently press the switch for 1 to 2 seconds until ZONE and the current zone setting is displayed on the trip computer .
2. Locate the compass module mounted on the base of the mirror . 3. Insert an appropriate diameter rod (paperclip) into the switch access hole underneath the compass module. 4. Gently press the switch for 2 to 4 seconds until CAL and a direction are displayed on the trip computer .
AUTOMATIC DIMMING INSIDE REAR VIEW MIRROR (IF EQUIPPED) The electronic day/night mirror will change from the normal state to the non-glare state when bright lights (glare) reach the mirror . When the mirror detects bright light from front or behind, it will automatically adjust to minimize glare.
POWER WINDOWS Press and hold the rocker switches to open and close windows. • Press the top portion of the rocker switch to close. • Press the bottom portion of the rocker switch to open. One touch down • Press AUTO and release quickly . The window will open fully .
Window lock The window lock feature allows only the driver to operate the power windows. Accessory delay W ith accessory delay , the window switches may be used for up to ten minutes after the ignition switch is turned to the OFF position or until either door is opened.
Relock The autolock feature repeats when: • any door is opened and closed • the brake pedal is released. Deactivating/activating the autolock feature Before following the procedure, make sure that the ignition is OFF and all vehicle doors and the liftgate window are closed.
CHILDPROOF DOOR LOCKS When these locks are set, the rear doors cannot be opened from the inside. The rear doors can be opened from the outside when the doors are unlocked. The childproof locks are located on rear edge of each rear door and must be set separately for each door .
3. Return to the center position to lock mirrors in place. Heated outside mirrors Both mirrors are heated automatically to remove ice, mist and fog when the rear window defrost is activated. Do not remove ice from the mirrors with a scraper or attempt to readjust the mirror glass if it is frozen in place.
• tissue box holder • compact disc changer Use only soft cups in the cupholder . Hard objects can injure you in a collision. The auxiliary power point is located on the instrument panel. Do not plug optional electrical accessories into the cigarette lighter .
POSITIVE RETENTION FLOOR MA T (IF EQUIPPED) Position the floor mat so that the eyelet is over the pointed end of the retention post and rotate forward to lock in. Make sure that the mat does not interfere with the operation of the accelerator or the brake pedal.
Make sure that the liftgate door and/or window are closed to prevent exhaust fumes from being drawn into the vehicle. This will also prevent passengers and cargo from falling out. If you must drive with the liftgate door or window open, keep the vents open so outside air comes into the vehicle.
light will illuminate for two seconds. Repeat procedure for all new keys. If key coding fails, the THEFT indicator light will flash. Coding failure can be caused by any of the following: • The new key was not inserted into the ignition within 15 seconds.
Locking the doors Press this control to lock all doors. T o confirm all doors are closed and locked, press the control a second time within five seconds. The doors will lock again, the horn will chirp and the lamps will flash. If any of the doors are ajar , the horn will make two quick chirps, reminding you to properly close all doors.
Replacing the batteries The transmitter is powered by one coin type three-volt lithium battery CR2032 or equivalent. T ypical operating range will allow you to be up to 10 meters (33 feet) away from your vehicle.
Replacing lost transmitters T ake all your vehicle’ s transmitters to your dealer for reprogramming if: • a transmitter is lost or • you want to purchase additional transmitters (up to four may be programmed).
• any door is open. Battery saver will shut off the interior lamps 40 minutes after the last door is closed. Controls and features 59.
SEA TING Using the manual lumbar support T urn the lumbar support control counterclockwise to increase firmness. T urn the lumbar support control clockwise to increase softness. Front seats Never adjust the driver’ s seat or seatback when the vehicle is moving.
Lift handle to move seat forward or backward. Pull lever up to adjust seatback. Using the armrest (if equipped) Pull the strap to move the armrest down. T o move the armrest up, lift it until it latches in the upright position. Adjusting the front power seat (if equipped) Never adjust the driver’ s seat or seatback when the vehicle is moving.
Do not pile cargo higher than the seatbacks to avoid injuring people in a collision or sudden stop. Always drive and ride with your seatback upright and the lap belt snug and low across the hips. Press to raise or lower the front portion of the seat cushion.
REAR SEATS Head restraints Push or pull the head rests to the desired position. Rear folding bench seat (if equipped) Folding down the rear seats Ensure that no objects such as books, purses or briefcases are on the floor in front of the second row seats before folding them down.
3. Press the green control on the seatback to release the closeout panel. Rotate the panel to closeout the space in the floor . 4. Once the second row seats are in the down position, the front seats may be readjusted. Returning the seat to upright Always latch the vehicle seat to the floor , whether the seat is occupied or empty .
Reclining the seatback Locate the lever at the bottom of the seatback marked “1”. Pull the lever upwards to recline the seatback. Third row seat (if equipped) The third row seat is equipped with combination lap and shoulder belts in the outboard seating positions and a manual adjust tongue lap belt in the center seating position.
Accessing the third row seat Y our vehicle is equipped with an easy entry second row seat feature which allows ready access to the third row seat. Y ou may enter the third row seat: • through the pa.
Removing the third row seat From the rear of the vehicle, with the liftgate open: 1. Disengage the lap/shoulder belt from the floor by inserting a key or small screwdriver through the hole in the boot of the detachable anchor . Then, press the release button to separate the detachable anchor from the anchor tongue.
• Pull the seat release lever located on the lower right side of the seatback while pushing the seatback down into the seat cushion. • The seatback will latch onto the cushion. 4. Lift the seat release bar located at the center of the seat near the floor to release the floor latches.
Before installing your third row seat, ensure that the detachable anchor tongues are stowed into the floor and the loose belts are stored out of the way . For proper latching, ensure that the floor tubs are clear of debris. From the rear of the vehicle, with the liftgate open: 1.
7. V erify that the safety belts can move freely on either side of the seat. SAFETY RESTRAINTS Safety restraints precautions Always drive and ride with your seatback upright and the lap belt snug and low across the hips. T o prevent the risk of injury , make sure children sit where they can be properly restrained.
It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts.
2. T o unfasten, push the red release button and remove the tongue from the buckle. The front and rear outboard safety restraints in the vehicle are combination lap and shoulder belts.
When to use the automatic locking mode • When a tight lap/shoulder fit is desired. • Anytime a child safety seat is installed in the vehicle. Refer to Safety Restraints for Children or Safety Seats for Children later in this chapter . How to use the automatic locking mode • Buckle the combination lap and shoulder belt.
clicking sound. This indicates the safety belt is now in the automatic locking mode. How to disengage the automatic locking mode Disconnect the combination lap/shoulder belt and allow it to retract completely to disengage the automatic locking mode and activate the vehicle sensitive (emergency) locking mode.
Shorten and fasten the belt when not in use. Front and second row safety belt height adjustment Y our vehicle has safety belt height adjustments for the driver , front passenger and second row passengers. Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder .
Safety belt extension assembly If the safety belt assembly is too short, even when fully extended, 20 cm (8 inches) can be added to the safety belt assembly by adding a safety belt extension assembly (part number 611C22). Safety belt extension assemblies can be obtained from your dealer at no cost.
Conditions of operation If... Then... The driver’ s safety belt is not buckled before the ignition key is turned to ON... The safety belt warning light illuminates for one to two minutes and the warning chime sounds for four to eight seconds.
Safety belt assemblies not in use during a collision should also be inspected and replaced if either damage or improper operation is noted. Failure to replace the safety belt assembly under the above conditions could result in severe personal injuries in the event of a collision.
Important supplemental restraint system (SRS) precautions The supplemental restraint system is designed to: • work with the safety belt to protect the driver and right front passenger • reduce cer.
Do not place objects or mount equipment on or near the air bag cover on the steering wheel or in front seat areas that may come into contact with a deploying air bag. Failure to follow this instruction may increase the risk of personal injury in the event of a collision.
How does the air bag supplemental restraint system work? The SRS is designed to activate when the vehicle sustains sufficient longitudinal deceleration. The fact that the air bags did not inflate in a collision does not mean that something is wrong with the system.
If the air bag is inflated, the air bag will not function again and must be replaced immediately .I ft h e air bag is not replaced, the unrepaired area will increase the risk of injury in a collision.
A difficulty with the system is indicated by one or more of the following: • The readiness light will either flash or stay lit. • The readiness light will not illuminate immediately after ignition is turned on. • A series of five beeps will be heard.
younger and who weigh 18 kg [40 lbs] or less), you must put them in safety seats made especially for children. Check your local and state or provincial laws for specific requirements regarding the safety of children in your vehicle. Never let a passenger hold a child on his or her lap while the vehicle is moving.
face or neck, the child should wear the lap and shoulder belt. Moving the child closer to the center of the vehicle may help provide a good shoulder belt fit.
edge of the seat cushion. Y ou may wish to discuss the special needs of your child with your pediatrician. SAFETY SEA TS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of the child.
capable of providing a tether anchorage. For more information on top tether straps, refer to Attaching safety seats with tether straps . Carefully follow all of the manufacturer’ s instructions included with the safety seat you put in your vehicle.
2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together . 3. While holding the shoulder and lap belt portions together , route the tongue through the child seat according to the child seat manufacturer’ s instructions.
5. T o put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is extracted and a click is heard. 6. Allow the belt to retract. The belt will click as it retracts to indicate it is in the automatic locking mode.
able to pull more belt out). If the retractor is not locked, unbuckle the belt and repeat steps two through nine. Check to make sure the child seat is properly secured before each use.
T ether anchor brackets may also be installed to the floor behind the second row seats. T ighten the anchor according to specifications. Otherwise, the safety seat may not be properly secured and the child may be injured in a sudden stop or collision.
PREP ARING T O ST ART YOUR VEHICLE Engine starting is controlled by the spark ignition system. This system meets all Canadian Interference-Causing Equipment standard requirements regulating the impulse electrical field strength of radio noise. When starting a fuel-injected engine, avoid pressing the accelerator before or during starting.
Do not start your vehicle in a closed garage or in other enclosed areas. Exhaust fumes can be toxic. Always open the garage door before you start the engine. See Guarding against exhaust fumes in this chapter for more instructions. If you smell exhaust fumes inside your vehicle, have your dealer inspect your vehicle immediately .
• Make sure the parking brake is set. • Make sure the gearshift is in P (Park). 3. T urn the key to 4 (ON) without turning the key to 5 (ST ART). BRAKE HOOD 1 2 3 4 5 Starting 94.
Make sure the corresponding lights illuminate briefly . If a light fails to illuminate, have the vehicle serviced. • If the driver’ s safety belt is fastened, the light ( ) will not illuminate. ST ARTING THE ENGINE 1. T urn the key to 5 (ST ART) without pressing the accelerator pedal and release as soon as the engine starts.
accelerator when the engine starts. 4. After idling for a few seconds, apply the brake and release the parking brake. Using the engine block heater (if equipped) An engine block heater warms the engine coolant, which improves starting, warms up the engine faster and allows the heater -defroster system to respond quickly .
If you ever smell exhaust fumes of any kind inside your vehicle, have your dealer inspect and fix your vehicle immediately . Do not drive if you smell exhaust fumes.
BRAKES Y our brakes are self-adjusting. Refer to the “Service Guide” for scheduled maintenance. Occasional brake noise is normal and often does not indicate a performance concern with the vehicle’ s brake system.
shudder while braking, felt mainly in the steering wheel, the vehicle most likely needs service. The ABS operates by detecting the onset of wheel lock up during brake applications and compensating for this tendency . The front wheels are prevented from locking even when the brakes are firmly applied.
there is sufficient space, will enable you to avoid obstacles and bring the vehicle to a controlled stop. • W e recommend that you familiarize yourself with this braking technique. However , avoid taking any unnecessary risks. Parking brake Apply the parking brake whenever the vehicle is parked.
The parking brake is not designed to stop a moving vehicle. However , if the normal brakes fail, the parking brake can be used to stop your vehicle in an emergency . Since the parking brake applies only the rear brakes, the vehicle’ s stopping distance will be adversely affected.
steering assist will decrease to improve steering feel. At lower speeds, maneuverability will be increased. If the amount of effort required to steer your vehicle changes at a constant vehicle speed, have the power steering system checked by your dealer or a qualified service technician.
The air suspension shut-off switch is located behind an access panel underneath the passenger side instrument panel. On vehicles equipped with Air Suspension, turn OFF the Air Suspension switch prior to jacking, hoisting or towing your vehicle. Normal vehicle operation does not require any action by the driver .
TRANSMISSION OPERA TION Automatic transmission operation Brake-shift interlock This vehicle is equipped with a brake-shift interlock feature that prevents the gearshift from being moved from P (Park) unless the brake pedal is depressed. If you cannot move the gearshift out of P (Park) with the brake pedal depressed: 1.
Do not rock the vehicle for more than a few minutes. The transmission and tires may be damaged or the engine may overheat. Always set the parking brake fully and make sure the gearshift is latched in P (Park). T urn off the ignition whenever you leave your vehicle.
R (Reverse) W ith the gearshift in R (Reverse), the vehicle will move backward. Always come to a complete stop before shifting into and out of R (Reverse). N (Neutral) W ith the gearshift in N (Neutral), the vehicle can be started and is free to roll.
more engine braking than (Overdrive) and is useful when: • driving with a heavy load • towing a trailer up or down steep hills • additional engine downhill braking is desired. If towing a trailer , refer to Driving while you tow in the T owing a trailer chapter .
gear , and will shift to 1 (Low) after vehicle decelerates to the proper speed. CONTROL-TRAC AUTOMA TIC FOUR-WHEEL DRIVE SYSTEM (IF EQUIPPED) Y our 4x4 features a heavy-duty Control-T rac system, including a computer -operated transfer case.
drive when above average power at reduced speeds is required. Utility and four -wheel drive vehicles are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed to perform satisfactorily under off-road conditions.
Shifting from 4H to 4L (and 4L to 4H) 1. Bring the vehicle to a stop. 2. Depress the brake. 3. Place the gearshift in N (Neutral). 4. Move the 4WD control to the 4H (or 4L) position. Shifting from A4WD to 4H Move the 4WD control from A4WD to 4H at any forward speed.
the outside. Do not grip the spokes. Drive cautiously to avoid vehicle damage from concealed objects such as rocks and stumps. Y ou should either know the terrain or examine maps of the area before driving. Map out your route before driving in the area.
accelerator slowly and avoid spinning the wheels. Mud and water If you must drive through high water , drive slowly . T raction or brake capability may be limited. When driving through water , determine the depth; avoid water higher than the bottom of the hubs (if possible) and proceed slowly .
change for the life of the vehicle. Rear axle lubricant quantities should not need to be checked unless a leak is suspected. Driving on hilly or sloping terrain When driving on a hill, avoid driving crosswise or turning on steep slopes. Y ou could lose traction and slip sideways.
ACCEL button (to resume speeds over 50 km/h (30 mph). Automatic transmission may shift frequently while driving up steep grades. Eliminate frequent shifting by shifting out of (Overdrive) into D (Drive). Driving on snow and ice A 4WD vehicle has advantages over 2WD vehicles in snow and ice but can skid like any other vehicle.
the hubs (truck)/wheel rims (car). Once through the water , always try the brakes. W et brakes do not stop the vehicle as effectively as dry brakes. Drying can be improved by moving your vehicle slowly while applying light pressure on the brake pedal.
specific to each vehicle and is listed on the Safety Compliance Label on the driver’ s door pillar . • GCWR (Gross Combined W eight Rating) : Maximum combined weight of towing vehicle (including passengers and cargo) and the trailer . The GCWR indicates the maximum loaded weight that the vehicle is allowed to tow .
Do not exceed the GVWR or the GA WR specified on the Safety Compliance Certification Label. Do not use replacement tires with lower weight capacities than the originals because they may lower the vehicle’ s GVWR and GA WR limitations. Replacement tires with a higher weight limit than the originals do not increase the GVWR and GA WR limitations.
T railer towing with your vehicle may require the use of a trailer tow option package. T railer towing puts additional loads on your vehicle’ s engine, transmission, axle, brakes, tires, and suspension. For your safety and to maximize vehicle performance, be sure to use the proper equipment while towing.
If your vehicle is equipped with the optional heavy duty trailer tow wiring, it is pre-wired for trailer towing. An electrical connector is provided under the instrument panel for installing a customer -supplied electric brake controller . Another electrical connector is provided at the hitch.
Engine Rear axle ratio T ire size Maximum GCWR T railer weight range (0 - maximum) 4x4 4.6L 3.55 40.6 cm (16 in) 5 216 kg (11 500 lbs.) 0-2 766 kg (0-6 100 lbs.) 4.6L 3.55 43.2 cm (17 in) 4 990 kg (11 000 lbs.) 0-2 494 kg (5 500 lbs.) 5.4L 3.31 40.6 cm (16 in) 5 443 kg (12 000 lbs.
is properly attached to your vehicle. See your dealer or a reliable trailer dealer if you require assistance. If your vehicle is not equipped with the factory heavy duty trailer tow option, auxiliary .
4. Attach the trailer to the vehicle and adjust the hitch equalizers so that the front bumper height is within 0–13 mm (0.5 in) of the reference point. After proper adjustment, the rear bumper should be no higher than in Step 3. 5. T urn the air suspension (if equipped) control to ON.
Do not connect a trailer’ s hydraulic brake system directly to your vehicle’ s brake system. Y our vehicle may not have enough braking power and your chances of having a collision greatly increase. Trailer lamps T railer lamps are required on most towed vehicles.
upshifting for optimum fuel economy and transmission cooling. • Anticipate stops and brake gradually . Servicing after towing If you tow a trailer for long distances, your vehicle will require more frequent service intervals. Refer to the Severe Duty Schedule in your “Service Guide” for more information.
• When stopped in traffic for long periods of time in hot weather , place the gearshift in P (Park) and increase idle speed. This aids engine cooling and air conditioner efficiency . • V ehicles with trailers should not be parked on a grade. If you must park on a grade, place wheel chocks under the trailer’ s wheels.
LUGGAGE RACK Load luggage at the front crossbar and adjust the rear crossbar as necessary . • Do not exceed 90.7 kg (200 lb) of luggage if the weight is placed directly on the crossbars. • Do not exceed 68 kg (150 lb) if the weight is resting directly on the roof.
HAZARD LIGHTS CONTROL Use only in an emergency to warn traffic of vehicle breakdown, approaching danger , etc. The hazard flashers can be operated when the ignition is off. • The hazard lights control is located on top of the steering column. • Depress hazard lights control to activate all hazard flashers simultaneously .
seconds and return the key to the OFF position. 5. Make a further check for leaks in the fuel system. The fuel pump shut-off switch is located in the passenger’ s foot well, behind the kick panel. FUSES AND RELA YS Fuses If electrical components in the vehicle are not working, a fuse may have blown.
Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire.
The fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Description 1 15A Flasher Relay 2 5A Instrument Cluster , Overhead T rip Computer (OTC) Module 3 25A Cigar Lighter 4 5A Park Lamp Re.
Fuse/Relay Location Fuse Amp Rating Description 5 15A Digital T ransmission Range (DTR) Sensor , Daytime Running Lamps (DRL) Module, Speed Control Servo/Amplifier Assembly , Heater -A/C Control Assemb.
Fuse/Relay Location Fuse Amp Rating Description 16 20A Instrument Cluster (W/O DRL), Daytime Running Lamps (DRL) Module, Hi-Beam Headlamps (Power supplied through Multi-Function Switch) 17 10A Heated .
Fuse/Relay Location Fuse Amp Rating Description 26 10A Daytime Running Lamps (DRL) Module, Right Headlamp (Power supplied through Multi-Function Switch) 27 5A Main Light Switch, Fog Lamp Relay 28 10A .
The high-current fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Description 1 20A* T railer T ow Running Lamp Relay , T railer T ow Backup Lamp Relay 2 10A* Air Bag Diagnostic Monitor.
Fuse/Relay Location Fuse Amp Rating Description 7 15A* Main Light Switch, Park Lamp Relay 8 30A* Main Light Switch, Headlamp Relay , Multi-Function Switch 9 15A* Daytime Running Lamps (DRL) Module, Fo.
Fuse/Relay Location Fuse Amp Rating Description 27 40A** Junction Box Fuse/Relay Panel, Heated Grid Relay 28 30A** T railer Electronic Brake Controller 29 30A** Flip W indow Relay , Hybrid Cooling Fan Relay * Mini Fuses ** Maxi Fuses Relays Relays are located in the power distribution box and should be replaced by qualified technicians.
The primary battery fuses are located in the engine compartment near the battery . Ford recommends that the megafuses are serviced by a qualified service technician.
The engine mini fuses are located on the drivers side of the engine compartment. Slot Number Fuse Amperage Rating Circuits Protected 1 5 amp Powertrain Control Module (PCM) 2 20 amp T railer T ow Stop.
Spare tire information Y our vehicle is equipped with a spare tire that may be used as a spare or a regular tire. The spare is identical to the other tires on your vehicle, although the wheel cover may not match.
Removing the jack and tools 1. Locate the access panel on the interior trim. Lift and rotate the two panel retaining clips and remove the panel. 2. Un-snap the wheel lug nut wrench, instructions and work gloves from their retaining bracket. 3. Remove the jack by turning the thumbwheel counterclockwise to relieve tension against the stowage bracket.
2. Install the retainer through the wheel center and slide the wheel under the vehicle. 3. T urn the spare handle clockwise until the tire is raised to its original position underneath the vehicle. The spare handle ratchets when the tire is raised to the stowed position.
3. Block the diagonally opposite wheel. 4. Obtain the spare tire and jack from their storage locations. 5. Use the tip of the lug wrench to remove any wheel trim. 6. Loosen each wheel lug nuts one-half turn counterclockwise but do not remove them until the wheel is raised off the ground.
• Front (4x2) • Front (4x4) • Rear Roadside emergencies 143.
• Never use the front or rear differential as a jacking point. 9. Remove the lug nuts with the lug wrench. 10. Replace the flat tire with the spare tire, making sure the valve stem is facing outward. Reinstall the lug nuts until the wheel is snug against the hub.
JUMP ST ARTING YOUR VEHICLE The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. Do not push start your vehicle. Y ou could damage the catalytic converter . Batteries contain sulfuric acid which burns skin, eyes, and clothing.
4. Check all battery terminals and remove any excessive corrosion before you attach the battery cables. 5. T urn the heater fan on in both vehicles to protect any electrical surges. T urn all other accessories off. Connecting the jumper cables 1. Position the vehicles so that they do not touch one another .
Jump starting 1. Start the booster vehicle and run the engine at moderately increased speed. 2. Start the engine of the vehicle with the discharged battery . 3. Once the engine has been started, run both vehicles for a further three minutes before disconnecting the leads.
WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or , if you are a member , your roadside assistance center . On 4x2 vehicles, it is acceptable to tow the vehicle with the front wheels on the ground and the rear wheels off the ground.
When calling for a tow truck, tell the operator what kind of vehicle you have. A towing manual is available from Ford Motor Company for all authorized tow truck operators. Have your tow truck driver refer to this manual for proper hook-up and towing procedures for your vehicle.
SERVICE RECOMMENDA TIONS T o help you service your vehicle: • W e highlight do-it-yourself items in the engine compartment for easy location. • W e provide a “Service Guide” which makes tracking routine service easy . If your vehicle requires professional service, your dealership can provide necessary parts and service.
• Keep all lit cigarettes, open flames and other lit material away from the battery and all fuel related parts. If you disconnect the battery , the engine must “relearn” its idle conditions before your vehicle will drive properly , as explained in Battery in this chapter .
OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the bottom of the instrument panel. 2. Go to the front of the vehicle and release the auxiliary latch that is located under the front center of the hood. Lift the hood until the lift cylinders hold it open.
2. Automatic transmission fluid dipstick 3. Engine oil filler 4. Engine oil dipstick 5. Power steering fluid reservoir 6. Brake fluid reservoir 7. Power distribution box 8.
5. Locate and carefully remove the engine oil level indicator (dipstick). 6. W ipe the indicator clean. Insert the indicator fully , then remove it again. • If the oil level is between the MIN and MAX marks , the oil level is acceptable. DO NOT ADD OIL.
• Oil levels above the MAX mark may cause engine damage. Some oil must be removed from the engine by a service technician. 7. Put the indicator back in and ensure it is fully seated. Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the engine oil in this chapter .
Do not use supplemental engine oil additives, oil treatments or engine treatments. They are unnecessary and could, under certain conditions, lead to engine damage which is not covered by your warranty .
BRAKE FLUID Checking and adding brake fluid Brake fluid should be checked and refilled as needed at least once each year: 1. Clean the reservoir cap before removal to prevent dirt or water from entering the reservoir . 2. Visually inspect the fluid level.
WINDSHIELD WASHER FLUID Checking and adding washer fluid Check the washer fluid whenever you stop for fuel. The reservoir is highlighted with a symbol. If the level is low , add enough fluid to fill the reservoir . In very cold weather , do not fill the reservoir all the way .
eventually empty . If this occurs, add engine coolant to the coolant reservoir . For more information on engine coolant maintenance, refer to Adding engine coolant in this chapter . Automotive fluids are not interchangeable; do not use engine coolant, antifreeze or windshield washer fluid outside of its specified function and vehicle location.
Never remove the coolant recovery cap while the engine is running or hot. If you must remove the coolant recovery cap, follow these steps to avoid personal injury: 1. Before you remove the cap, turn the engine off and let it cool. 2. When the engine is cool, wrap a thick cloth around the cap.
may void your warranty of your vehicle’ s engine cooling system. Recycled engine coolant Ford Motor Company recommends that Ford and Lincoln-Mercury dealers use recycled engine coolant produced by Ford-approved processes.
container to ensure the coolant concentration in your vehicle is such that the coolant will not freeze at the temperature level in which you drive during winter months. Never increase the engine coolant concentration above 60%. Leave a 50/50 mixture of engine coolant and water in your vehicle year -round in non-extreme climates.
no air conditioning capability . Continued operation will increase engine temperature and cause the engine to completely shut down. The vehicle will coast to a stop. As the engine temperature cools, the engine may be re-started. T ake your vehicle to a service facility as soon as possible to minimize engine damage.
2. While the engine idles, turn the steering wheel left and right several times. 3. T urn the engine off. 4. Check the fluid level in the reservoir . It should be between the MIN and MAX lines.
Capacities and specifications chapter . An overfill condition of transmission fluid may cause shift and/or engagement concerns and/or possible damage. Do not drive the vehicle if the fluid level is be.
The transmission fluid should be in this range if at room temperature (10°C-35°C [50°F-95°F]) (see figure to the right). If your vehicle has been operated for an extended period at high speeds, in.
7. If necessary , add fluid in .25L (1/2 pint) increments through the filler tube until the level is correct. 8. If an overfill occurs, excess fluid should be removed by a qualified technician. An overfill condition of transmission fluid may cause shift and/or engagement concerns and/or possible damage.
BA TTER Y Y our vehicle may be equipped with a Motorcraft maintenance-free battery . If the original equipment battery needs replacing, it may be replaced with a low-maintenance battery . The low-maintenance battery normally does not require additional water during its life of service.
cleaning them, and apply a small quantity of grease to the top of each battery terminal to help prevent corrosion. If your battery has a cover/shield, make sure it is reinstalled after the battery is replaced.
• Always dispose of automotive batteries in a responsible manner . Follow your communities standards for disposal. Call your local recycling center to find out more about recycling automotive batteries. AIR CLEANER FILTER MAINTENANCE Refer to the “Service Guide” for the appropriate intervals for changing the air cleaner filter .
For information on replacement air filter elements, refer to the Capacities and specifications chapter . WINDSHIELD WIPER BLADES Check the wiper blades at least twice a year or when they seem less effective. Substances such as tree sap and some hot wax treatments used by commercial car washes reduce the effectiveness of wiper blades.
1. Pull the wiper arm away from the windshield and lock into the service position. 2. T urn the blade at an angle from the wiper arm. Push the lock pin with a screwdriver to release the blade and pull the wiper blade down toward the windshield to remove it from the arm.
U.S. Department of T ransportation-T ire quality grades: The U.S. Department of T ransportation requires Ford to give you the following information about tire grades exactly as the government has written it.
T emperature A B C The temperature grades are A (the highest), B, and C, representing the tire’ s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel.
has been parked for at least one hour or has been driven less than 5 km (3 miles). • Adjust tire pressure to recommended specifications found on the Safety Compliance Certification Label. Improperly inflated tires can affect vehicle handling and can fail suddenly , possibly resulting in loss of vehicle control.
Replacing the tires Replace the tires when the wear band is visible through the tire treads. Failure to follow these precautions may adversely affect the handling of the vehicle and make it easier to lose control and roll over .
or equivalent. SAE class “S” or other conventional link type chains may contact and cause damage to the vehicle’ s wheel house and/or body . • Install chains securely , verifying that the chains do not touch any wiring, brake lines or fuel lines.
If you do not use the proper fuel cap, the pressure in the fuel tank can damage the fuel system or cause it to work improperly in a collision. The fuel system may be under pressure. If the fuel cap is venting vapor or if you hear a hissing sound, wait until it stops before completely removing the cap.
promptly remove contaminated clothing and wash skin thoroughly with soap and water . • If fuel is splashed in the eyes, remove contact lenses, flush with water for 15 minutes and seek medical attention. • Be particularly careful if you are taking “Antabuse” or other forms of disulfiram for the treatment of alcoholism.
control devices and systems may be adversely affected. Repair of damage caused by using a fuel that your vehicle was not designed for may not be covered by your warranty . Octane recommendations Y our vehicle is designed to use regular unleaded with an (R+M)/2 octane rating of 87.
recommend the use of gasolines that meet the AAMA specification if they are available. It should not be necessary to add any aftermarket products to your fuel tank if you continue to use a high-quality fuel.
• T o help reduce early nozzle shut off and fuel spillage, park your vehicle so the fuel filler door is level. • A void excessively fast fuel dispensing rates (over 38 L [10 gallons] per minute). • If you spill fuel on the body of your vehicle, clean it off immediately .
3. After at least three to five fuel tank fill-ups, fill the fuel tank and record the current mileage reading. 4. Use one of the following equations to calculate fuel economy . Liters used x 100 4 T otal kilometers traveled T otal miles traveled 4 T otal gallons used Keep a record for at least one month.
Guide” are required because they are considered essential to the life and performance of your vehicle and to its emissions system. If other than Ford, Motorcraft or Ford authorized parts are used fo.
who manufactures, repairs, services, sells, leases, trades vehicles, or supervises a fleet of vehicles are not permitted to intentionally remove an emission control device or prevent it from working. Information about your vehicle’ s emission system is on the V ehicle Emission Control Information Decal located on or near the engine.
• First, at least 10 minutes of driving on an expressway or highway . • Next, at least 20 minutes driving in stop and go, city type traffic with at least four idle periods. Allow the vehicle to sit for at least eight hours without starting the engine.
Replacing headlamp bulbs Handle a halogen headlamp bulb carefully and keep out of children’ s reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hand could cause the bulb to break the next time the headlamps are operated.
8. Insert the glass end of the new bulb into the headlamp assembly socket. When the grooves in the plastic base are aligned, push the bulb into the socket until the plastic base contacts the rear of the socket. 9. Slip bulb retaining ring over the plastic base and lock the ring into the socket by turning it clockwise until you feel a “stop.
Replacing parking lamp/turn signal bulbs 1. Remove screw from the top of lamp assembly . 2. Disengage lamp assembly (it has a snap fit). 3. Remove the electrical connector from the bulb by grasping the wire and pulling it rearward. 4. Remove bulb retainer ring by turning it counterclockwise about 1/4 turn, then slide the ring off the plastic base.
9. Align top and bottom ribs of parking lamp assembly with corresponding slots on front of vehicle. 10. Push gently until parking lamp assembly seats (you will hear a snap). 11. Replace screw removed in step 1. Replacing foglamp bulbs 1. Disconnect the electrical connector from the back of the foglamp assembly .
1. Remove the four screws that secure the high-mount brakelamp lens. 2. Carefully remove the lens. 3. Each of the three bulbs may be removed with a 1 ⁄ 4 turn counterclockwise and a careful pull. 4. Replace the bulbs as needed and replace the high-mount brakelamp lens.
Replacing license plate lamp bulbs The license plate bulbs are located under and behind the rear bumper . T o change the license plate lamp bulbs: 1. Reach under and behind the rear bumper to locate the bulb connector . 2. T wist the connector counterclockwise 1 ⁄ 4 turn and carefully pull to remove it.
REPLACING THE INTERIOR BULBS Check the operation of the following interior bulbs frequently: • interior overhead lamp • map lamp Map lamps T o change the map lamp bulbs: 1. Use a small screwdriver to remove the map lamp lens. 2. T o remove the old bulb, twist 1 ⁄ 4 turn and pull it out.
CLEANING AND CARING FOR YOUR VEHICLE Refer to the “Customer Assistance Guide” for a list of Ford-approved cleaners, polishes and waxes. W ashing your vehicle W ash your vehicle regularly with cold or lukewarm water . Never use strong detergents or soap.
any bugs and tar before waxing vehicle. Use cleaning fluid or alcohol with a clean cloth to remove. Use tar remover to remove any tar spots. Repairing paint chips Minor scratches or paint damage from road debris may be repaired with touch-up, paint repair foil or aerosol paint spray from the Ford accessory line.
• Do not spray with cold water to avoid cracking the engine block or other engine components. • Cover the highlighted areas to prevent water damage when cleaning the engine. • Never wash or rinse the engine while it is running; water in the running engine may cause internal damage.
T o avoid scratching the lamps, do not use a dry paper towel, chemical solvents or abrasive cleaners. Cleaning the wiper blades If the wiper blades do not wipe properly , clean the windshield and wiper blades with undiluted windshield wiper solution or a mild detergent.
Check the safety belt system periodically to make sure there are no nicks, wear or cuts. If your vehicle has been involved in an accident, refer to the Safety belt maintenance section in the Seating and safety restraints chapter . Cleaning leather seats For routine cleaning, wipe the surface with a soft, damp cloth.
products can damage the leather . In some instances, color or dye transfer can occur when wet clothing (wool, denim, leathers or other non-colorfast garments) comes in contact with leather upholstery . If this occurs, the leather should be cleaned immediately to avoid permanent staining.
MOTORCRAFT P ART NUMBERS Component 4.6L engine 5.4L engine Air filter F A-1632 F A-1632 Fuel filter FG-872 FG-872 Battery (standard) BXT -59 BXT -59 Battery (optional) BXT -65-750 BXT -65-750 Oil filt.
Fluid Ford Part Name Application Capacity W indshield washer fluid Ultra-Clear W indshield Concentrate All 4.1L (4.5 quarts) Engine coolant Ford Premium Cooling System Fluid 4.6L engine with 2 row radiator 17.9 L (19.9 quarts) 4.6L engine with 1 row radiator 17.
inch) below the bottom of the filler hole. LUBRICANT SPECIFICA TIONS Item Ford part name Ford part number Ford specification W indshield washer fluid reservoir Ultra-Clear W indshield W asher Concentr.
Item Ford part name Ford part number Ford specification Engine oil Motorcraft 5W30 Super Premium Motor Oil XO-5W30-QSP WSS-M2C153-G with API Certification Mark 4x4 front wheel bearings, 4x4 spindle ne.
complete refill of Ford T raction-Lok rear axles. ENGINE DA T A Engine 4.6L engine 5.4L engine Cubic inches 281 330 Horsepower 215 @ 4400 rpm 230 @ 4250 rpm T orque 290 lb. ft. @ 3250 rpm 325 lb. ft. @ 3000 rpm Required fuel grade 87 octane 87 octane Firing order 1-3-7-2-6-5-4-8 1-3-7-2-6-5-4-8 Spark plug gap 1.
4 1 3 5 2 Capacities and specifications 205.
IDENTIFYING YOUR VEHICLE Safety compliance label The National Highway T raffic Safety Administration Regulations require that a Safety Compliance Certification Label be affixed to a vehicle and prescribe where the Safety Compliance Certification Label may be located.
REPORTING SAFETY DEFECTS (U.S. ONL Y) If you believe that your vehicle has a defect that could cause a crash, or could cause injury or death, you should immediately inform the National Highway T raffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company .
Aiming headlamps .................... 193 Air bag supplemental restraint system .......................................... 78 and child safety seats .............. 80 description ................................ 79 disposal ...........................
Fuel calculating fuel economy ....... 182 improving fuel economy ........ 126 octane rating ...........................180 quality ...................................... 180 safety information relating to automotive fuels ..................... 177 Fuel gauge .
Relays .................................128,136 Remote entry system ................. 55 illuminated entry ...................... 58 locking/unlocking doors ...... 55,56 replacement/additional transmitters ............................... 58 replacing the batteries .
W indshield washer fluid and wipers checking and adding fluid ..... 158 checking and replacing wiper blades ...................................... 171 operation .
212.
213.
214.
215.
Recommended fuel Unleaded fuel only - 87 octane Fuel tank capacity-4x2 without air suspension 98.0L (26 gallons) Fuel tank capacity-4x2 vehicles with air suspension and 4x4 vehicles 114.
Een belangrijk punt na aankoop van elk apparaat Ford 1998 Taurus (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Ford 1998 Taurus heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Ford 1998 Taurus vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Ford 1998 Taurus leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Ford 1998 Taurus krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Ford 1998 Taurus bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Ford 1998 Taurus kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Ford 1998 Taurus . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
