Gebruiksaanwijzing /service van het product 2002 Thunderbird van de fabrikant Ford
Ga naar pagina of 232
Introduction 4 Instrument Cluster 8 W arning and control lights 8 Gauges 14 Entertainment Systems 16 AM/FM stereo with CD 16 Climate Controls 30 Electronic automatic temperature control 30 Lights 43 H.
Driving 125 Starting 125 Brakes 129 T raction control 131 T ransmission operation 133 V ehicle loading 139 T railer towing 141 Roadside Emergencies 145 Getting roadside assistance 145 Hazard flasher s.
Accessories 223 Index 225 All rights reserved. Reproduction by any means, electronic or mechanical including photocopying, recording or by any information storage and retrieval system or translation in whole or part is not permitted without written authorization from Ford Motor Company .
CALIFORNIA Proposition 65 W arning W ARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
SAFETY AND ENVIRONMENT PROTECTION W arning symbols in this guide How can you reduce the risk of personal injury and prevent possible damage to others, your vehicle and its equipment? In this guide, answers to such questions are contained in comments highlighted by the warning triangle symbol.
These are some of the symbols you may see on your vehicle. V ehicle Symbol Glossary Safety Alert See Owner ’ s Guide Fasten Safety Belt Air Bag-Front Air Bag-Side Child Seat Child Seat Installation .
V ehicle Symbol Glossary Power W indows Front/Rear Power W indow Lockout Child Safety Door Lock/Unlock Interior Luggage Compartment Release Symbol Panic Alarm Engine Oil Engine Coolant Engine Coolant .
W ARNING LIGHTS AND CHIMES W arning lights and gauges can alert you to a vehicle condition that may become serious enough to cause expensive repairs. A warning light may illuminate when a problem exists with one of your vehicle ’ s functions. Many lights will illuminate when you start your vehicle to make sure the bulb works.
If the light remains on, have your vehicle serviced at the first available opportunity . Light is blinking: Engine misfire is occurring which could damage your catalytic converter . Y ou should drive in a moderate fashion (avoid heavy acceleration and deceleration) and have your vehicle serviced at the first available opportunity .
level or a brake system malfunction and the brake system should be serviced immediately by a qualified technician. Refer to Brakes in the Driving chapter for more information.
Safety belt Illuminates to remind you to fasten your safety belts. For more information, refer to the Seating and safety restraints chapter . Engine coolant temperature Illuminates when the engine coolant temperature is high. Stop the vehicle as soon as safely possible, switch off the engine and let it cool.
Low fuel Illuminates when the fuel level in the fuel tank is at or near empty , refer to Fuel gauge in this chapter for more information. Speed control Illuminates when the speed control is activated. Low washer fluid Illuminates when the windshield washer fluid is low .
Door ajar Illuminates when any door or the trunk is open. Safety belt warning chime Sounds to remind you to fasten your safety belts. BeltMinder 姟 chime Sounds intermittently to remind you to fasten your safety belts.
GAUGES Engine coolant temperature gauge Indicates the temperature of the engine coolant. At normal operating temperature, the needle remains within the normal area (the area between the “ H ” and “ C ” ); if the needle goes above the normal range, the engine is overheating.
Fuel gauge Displays approximately how much fuel is in the fuel tank. The fuel gauge may vary slightly when the vehicle is in motion or on a grade. When refueling the vehicle from an empty indication, the amount of fuel that can be added will be less than the advertised capacity due to the reserve fuel.
AUDIOPHILE AM/FM STEREO IN DASH SIX CD RADIO 1. Seek control 2. Rewind/Fast forward control 3. DSP control 4. Phone/mute control 5. Eject control 6. Bass/treble control 7. Select control 8. Balance/fade control 9. Menu control 10. Radio preset controls 11.
If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “ nominal ” listening level when the ignition switch is turned back on. Speed sensitive volume W ith this feature, radio volume changes automatically and slightly with vehicle speed to compensate for road and wind noise.
Tune adjust in radio mode • Press to move to the next frequency down the band (whether or not a listenable station is located there). Hold the control to move through the frequencies quickly . • Press to move to the next frequency up the band (whether or not a listenable station is located there).
Scan function The scan function works in radio or CD mode. Scan function in radio mode Press the SCAN control to hear a brief sampling of all listenable stations on the frequency band. Press the SCAN control again to stop the scan mode. Scan function in CD mode Press the SCAN control to hear a short sampling of all selections on the CD.
Starting autostore 1. Press and momentarily hold the AM/FM control. 2. AUTOSET will flash in the display as the frequency band is scrolled through. 3. When the six strongest stations are filled, the station stored in memory preset control 1 will start playing.
Display description Six circles are always lit in the digital display . These signify the six CD slots in the audio system. When a disc is loaded into a particular slot (1 – 6), the number inside that specific circle lights. If the circle is empty , there is no CD in that particular slot.
Eject Press the EJ control to stop and eject a CD. Y ou can choose which CD will be ejected by pressing the EJ control and the desired preset number (1 – 6). For example, to eject CD 2, press the EJ control and then press the preset 2 control. If you do not choose a specific CD, the player will eject the current CD.
Shuffle feature Press the SHUF control until the desired shuffle mode is displayed. The audio system will then engage the desired shuffle mode. When engaged, the shuffle feature has two different modes: SHUFFLE DISC and SHUFFLE TRK. SHUFFLE DISC randomly plays tracks from all the discs presently in the audio system.
Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. Press the BAL control. Use the SEL control to adjust the sound between the left and right speakers. Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers.
SELECT HOURS, SELECT MINUTES — Allows you to adjust the hours and minutes. Refer to Setting the clock. TRAFFIC ON/OFF — T raffic announcements can be programmed as local or distant. Refer to T raffic announcements. RDS ON/OFF — This feature allows your audio system to receive text information from RDS-equipped FM radio stations.
T o disengage the feature, press the MENU control until TRAFFIC ON displays. Press the SEL control. The display will read TRAFFIC OFF . T raffic announcements are not available in most U.S. markets. Program type This feature allows you to search for RDS stations selectively by their program type.
Press the DSP control to access the DSP menu. Press the SEL control to enter one of the following modes: • DSP OFF • SIGNAL MODE • OCCUP ANCY MODE Use the SEL control to select the desired signal mode (the selected mode will appear in the display).
Use the SEL control to manually set the time. • Press to increase hours/minutes. • Press to decrease hours/minutes. Press the MENU control again to disengage the clock mode. CLEANING COMPACT DISCS Inspect all discs for contamination before playing.
RADIO RECEPTION FACTORS Three factors can affect radio reception: • Distance/strength. The further an FM signal travels, the weaker it is. The listenable range of the average FM station is approximately 40 km (24 miles). This range can be affected by “ signal modulation.
DUAL AUTOMATIC T EMPERATURE CONTROL (DA TC) SYSTEM 1. A/C control 2. W indshield defrost control 3. Recirculated air control 4. Passenger temperature control 5. Rear defrost control 6. Heated wiper rest/windshield control 7. W indshield and floor control 8.
Y our vehicle is equipped with a Dual Automatic T emperature Control (DA TC) system. The system will maintain a selected temperature and automatically control air flow .
Turning the DA TC system on, dual zone control Press the passenger temperature control to turn the DA TC system on in dual zone control. While in dual zone control, independent temperatures are maintained for both the driver and passenger , and both set temperatures are displayed.
When in AUTO and weather conditions require heat, the DA TC directs the majority of the airflow to the floor area. The system will allow some airflow out of the defroster , demister outlets and outer instrument panel registers in order to reduce window fogging.
When in single zone control (only driver set temperature displayed), press and hold the AUTO control for approximately two seconds to return the DA TC system to dual zone control. Independent driver and passenger temperatures will be maintained. The previous passenger set temperature and the current driver set temperature are displayed.
Passenger side temperature selection T o control the temperature, select any temperature between 19 ° C (65 ° F) and 29 ° C (85 ° F) by pressing the temperature control on the passenger side of the system.
When the fan is adjusted in the AUTO mode, the AUTO indicator will remain lit and the system will remain in auto operation. T o return to automatic fan operation, press AUTO. The fan icon and bars will disappear from the display , and the DA TC system will return to full automatic operation.
very hot conditions. Recirculated air may also help to keep undesired outside odors from reaching the vehicle interior . It is recommended to allow the DA TC system to automatically control the selection of outside or recirculated air . The recirculation control cannot be selected in the defrost mode, as interior fogging may occur .
The air conditioning compressor can operate in all modes except OFF . However , the air conditioning will only function if the outside temperature is about 2 ° C (35 ° F) or higher .
Electric window heaters (heated wiper rest) — Located at the base of the windshield, this feature heats the front glass area below the area heated by the front defroster where the windshield wipers sit in their parked position. When activated, the feature keeps the wiper blades warm and reduces the chance of ice build up on the blades.
temperatures will be displayed for 4 seconds. Following this, the outside temperature display will return to the window . The outside temperature reading is most accurate when the vehicle is moving. Higher readings may be obtained when the vehicle is not moving.
• Do not place items over the climate temperature sensor grid. This may cause improper operation of the DA TC system. • W ith the ignition in the OFF position after operating the vehicle, some vehicle sounds related to the climate control system may be heard.
REAR WINDOW DEFROSTER Press the rear window defroster control to clear the rear window of thin ice or fog. The indicator will illuminate when the rear window defroster is selected. The ignition must be in the RUN position and the engine running in order to operate the rear window defroster .
MASTER LIGHTING SWITCH Rotate the headlamp control to the first position to turn on the parking lamps. Rotate to the second position to turn on the headlamps. Autolamp control The autolamp system provides light sensitive automatic on-off control of the exterior lights normally controlled by the master lighting switch.
Always remember to turn on your headlamps at dusk or during inclement weather . The Daytime Running Light (DRL) System does not activate your tail lamps and generally may not provide adequate lighting during these conditions. Failure to activate your headlamps under these conditions may result in a collision.
HEADLAMP VERTICAL AIM ADJUSTMENT 1. Park the vehicle on a level surface approximately 7.6 meters (25 feet) from a vertical wall or screen directly in front of it. • (1) Eight feet • (2) Center height of lamp to ground • (3) T wenty five feet • (4) Horizontal reference line 2.
TURN SIGNAL CONTROL • Push down to activate the left turn signal. • Push up to activate the right turn signal. INTERIOR LAMPS Map lamps The map lamps and controls are located on the rearview mirror . Press the controls on the bottom of the mirror to activate the lamps.
Using the right bulbs Replacement bulbs are specified in the chart below . Headlamp bulbs must be marked with an authorized “ D.O.T . ” for North America and an “ E ” for Europe to assure lamp performance, light brightness, pattern and safe visibility .
Replacing headlamp bulbs T o remove the headlamp bulb: 1. Make sure headlamp switch is in OFF position, then open the hood. 2. Pry up the two retainer pins to release the headlamp assembly from the vehicle. 3. Remove the screw from the back of the headlamp and pull headlamp forward.
6. W ithout turning, remove the old bulb from the lamp assembly by pulling it straight out of the lamp assembly . T o install the new bulb: Handle a halogen headlamp bulb carefully and keep out of children ’ s reach. Grasp the bulb only by its plastic base and do not touch the glass.
Replacing front parking lamp/turn signal bulbs 1. Make sure headlamp switch is in OFF position, then open the hood. 2. Pry up the two retainer pins to release the headlamp assembly from the vehicle. 3. Remove the screw from the back of the headlamp and pull headlamp forward.
Replacing front/rear side marker bulbs 1. Make sure the headlamp switch is in the OFF position and then remove the screw and carefully pull the lamp assembly out from the bumper . 2. Rotate bulb socket counterclockwise and remove from lamp assembly . 3.
Replacing tail/brake/turn/backup lamp bulbs The tail/brake//turn/backup bulbs are located in the tail lamp assembly , one just below the other . Follow the same steps to replace either bulb: Prior to pulling the carpet away , in step 1, the trunk trim scuff plate must be removed.
Replacing license plate lamp bulbs 1. Make sure the headlamp switch is in the OFF position and then remove two screws and the license plate lamp assembly from the vehicle. 2. Rotate bulb socket counterclockwise and remove from lamp assembly . 3. Carefully pull the bulb from the socket and push in the new bulb.
WINDSHIELD WIPER/WASHER CONTROLS Rotate the windshield wiper control to the desired interval, low or high speed position. The ignition must be in the ACC or RUN position to operate the windshield wiper . The bars of varying length are for intermittent wipers.
Changing the wiper blades T o replace the wiper blades: 1. Pull the wiper arm away from the windshield and lock into the service position. 2. T urn the blade at an angle from the wiper arm. Push the lock pin manually to release the blade and pull the wiper blade down toward the windshield to remove it from the arm.
During easy exit operation, the column will move to the full in and up position. When the key is inserted into the ignition switch, the column will return to the previous setting. When you remove the key , the column will move away . AUXILIARY POWER POINT The power point is an additional power source for electrical accessories.
• Press the bottom portion of the rocker switch to open. One touch down • Press AUTO completely down to the second detent. The driver ’ s window will open fully .
Proper operation of the short drop glass requires that the windows be calibrated. Though your windows will have been calibrated before your vehicle is delivered to you, it is possible for the windows to lose calibration.
LOCKABLE AND ELECTRONIC TRUNK REMOTE CONTROL The remote trunk release control is located on the driver ’ s door trim panel and can be operated at any time, except when the security system is armed. This control will not work until the vehicle is disarmed.
T o turn speed control off • Press OFF or • T urn off the vehicle ignition. Once speed control is switched off, the previously programmed set speed will be erased. T o set a speed • Press SET+ / SET−. For speed control to operate, the speed control must be ON and the vehicle speed must be greater than 48 km/h (30 mph).
T o set a higher set speed • Press and hold SET+. Release the control when the desired vehicle speed is reached or • Press and release SET + to operate the T ap-Up function. Each press will increase the set speed by 1.6 km/h (1 mph) or • Accelerate with your accelerator pedal.
T o disengage speed control • Press CANCEL, or • depress the brake pedal. Disengaging the speed control will not erase the previously programmed set speed.
T o return to a previously set speed • Press RESUME. For RESUME to operate, the vehicle speed must be faster than 48 km/h (30 mph). Indicator light This light comes on when the vehicle speed control is engaged and actively controlling vehicle speed.
In AM, FM1, or FM2 mode: • Press ⌬ or ⵜ to select preset stations within the selected radio band. In T ape mode: • Press ⌬ or ⵜ to select the next selection on the tape. In CD mode: • Press ⌬ or ⵜ to select the next selection on the CD.
Do not lower the top when the top material is wet. If you raise and lower the convertible top several times in a row , the motor will heat up, causing the thermal circuit breaker to open so that the top will stop operating. The convertible top will operate again after allowing the motor to cool several minutes.
1. Push boot rearward and engage boot under the upper back panel at the rear and the quarter panel along the sides. 2. Fasten the snaps on boot to the quarter trim panel on both sides of the vehicle and at the center . 3. T o remove unfasten the snaps.
2. Remove the tonneau cover and store it in the luggage compartment. 3. Push the two screws down into the windscreen panel of your vehicle. 4. Push the convertible top switch, holding it until the top unfolds and moves forward toward the windshield header .
8. T o fasten both clamps securely , push the clamp handles into the header on the top until they are flush with the header . Pulling down on the header at the center grip while closing the latches may assist in fastening the clamps. Use the pull cups located on either side of the convertible top handle.
REMOVABLE TOP (IF EQUIPPED) For more information see the CD Rom included with this guide. Installing the removable top The front screw fittings must be checked to see that they are firmly seated after driving a distance of approximately 50 to 60 km (30 to 40 miles).
Once per year , apply a small amount of silicone lubricant, F5AZ – 19553 – AA, to the receivers as shown. The lubricant should be sprayed directly into the hole to avoid contaminating the trim parts. 3. Lower the rear of the top into position so that the pins are placed into the bracket receivers.
6. Partially turn, 1/2 turn forward, the levers of the top (located in the rear on the left and right-hand side of the vehicle). 7. Using the mounting key , loosely screw in the two screws at the front of the top by two or three turns. The two screws are already located in the windscreen panel of your vehicle.
Removing the top It is recommended that you prepare the storage rack before removing the top. See Removable top storage rack in this section. 1. T ake the mounting key from the bag located in the trunk. 2. Using the mounting key , loosen the two screws at the front of the top.
1. Remove the storage rack from the package and place the bumper end of the uprights on the floor with the wheels facing you. 2. Locate the two chrome locking buttons on each of the two rack legs. 3. Firmly squeeze the two chrome buttons (top and bottom) on one leg and rotate the leg toward you until the leg snaps into place.
8. Place the removable top on the storage rack. Make sure the rear edge of the removable top rests on the rubber bumpers of the rack legs. This prevents damage to the painted edge and the weather -strips. 9. Buckle and tighten the retaining strap and unlock the cart wheels before moving the top and cart.
CENTER CONSOLE Y our vehicle may be equipped with a variety of console features. These include: • Utility compartment • Cellular phone (if equipped) • Cupholders • Ash tray POSITIVE RETENTION FLOOR MA T Position the driver floor mat so that the eyelet is over the pointed end of the retention post and rotate forward to lock in.
KEYS The key operates all locks on your vehicle. In case of loss, replacement keys are available from your dealer . Y ou should always carry a second key with you in a safe place in case you require it in an emergency . Refer to SecuriLock 娂 Passive Anti-Theft System for more information.
T o open the luggage compartment door (lid) from within the luggage compartment, pull the illuminated “ T ” shaped handle and push up on the trunk lid. The handle is composed of a material that will glow for hours in darkness following brief exposure to ambient light.
Changes or modifications not expressly approved by the party responsible for compliance could void the user ’ s authority to operate the equipment. Y our remote entry system contains two remote transmitters which provide remote control of several features.
Unlocking the doors Press this control to unlock the driver door and disarm the perimeter alarm (if armed). The interior lamps will illuminate. Press the control a second time within three seconds to unlock all the doors. Opening the trunk Press this control to open the trunk.
Replacing the battery The remote transmitter is powered by one coin type three-volt lithium battery CR2032 or equivalent. T ypical operating range will allow you to be up to 10 meters (33 feet) away from your vehicle.
Reprogramming transmitters It will be necessary to reprogram all the transmitters to the vehicle at the same time while performing this procedure. T o program the transmitter yourself: 1.
Relock The autolock feature repeats when: • the passenger ’ s door is opened then closed while the engine is running, and • you put the vehicle in motion. Deactivating/activating the autolock/relock feature Before following the procedure, make sure that the ignition is OFF and all vehicle doors are closed.
• When the ignition is in the ON position, the indicator will glow for 3 seconds to indicate normal system functionality . If a problem occurs with the SecuriLock 娂 system, the indicator will flash rapidly or glow steadily when the ignition is in the ON position.
problem occurs, turn ignition OFF and restart the engine with all other objects on the key ring held away from the ignition key . Check to make sure the coded key is an approved Ford coded key . If your keys are lost or stolen you will need to do the following: • Use your spare key to start the vehicle.
3. W ithin ten seconds of turning the ignition to 1 (LOCK), insert the second previously programmed coded key into the ignition and turn the ignition from 1 (LOCK) to 4 (RUN) (maintain ignition in 4 (RUN) for at least one second but no more than ten seconds).
Arming the system When armed, the perimeter alarm will help protect your vehicle from unauthorized entry . When unauthorized entry occurs, the system will flash the turn signal lamps and the theft indicator lamp and will sound the horn. The system is ready to arm whenever the key is out of the ignition.
SEA TING Adjustable head restraints (if equipped) Y our vehicle ’ s seats may be equipped with head restraints which are vertically adjustable. The purpose of these head restraints is to help limit head motion in the event of a rear collision.
Using the manual lumbar support The lumbar control is located on the front of the driver ’ s seat cushion. T urn to adjust lumbar support. Using the manual recline function (if equipped) Never adjust the driver ’ s seat or seatback when the vehicle is moving.
The driver and passenger seat must be in the upright position and the lap belt must be snug and low across the hips while the vehicle is moving. Reclining the seatback can cause an occupant to slide under the seat ’ s safety belt, resulting in severe personal injuries in the event of a collision.
The driver and passenger seat must be in the upright position and the lap belt must be snug and low across the hips while the vehicle is moving. Reclining the seatback can cause an occupant to slide under the seat ’ s safety belt, resulting in severe personal injuries in the event of a collision.
It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts.
1. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) until you hear a snap and feel it latch. Make sure the tongue is securely fastened in the buckle. 2. T o unfasten, push the release button and remove the tongue from the buckle.
BEL T AND RETRACTOR ASSEMBL Y MUST BE REPLACED if the seat belt assembly “ automatic locking retractor ” feature or any other seat belt function is not operating properly when checked according to the procedures in W orkshop Manual. Failure to replace the Belt and Retractor assembly could increase the risk of injury in collisions.
• Grasp the shoulder portion and pull downward until the entire belt is extracted. • Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode. In this mode, the shoulder belt is automatically pre-locked.
BEL T AND RETRACTOR ASSEMBL Y MUST BE REPLACED if the seat belt assembly “ automatic locking retractor ” feature or any other seat belt function is not operating properly . In addition, all seat belts should be checked for proper function. Failure to replace the belt and retractor assembly could increase the risk of injury in collisions.
Conditions of operation If... Then... The driver ’ s safety belt is not buckled before the ignition switch is turned to the RUN position... The safety belt warning light illuminates 1-2 minutes and the warning chime sounds 4-8 seconds.
The purpose of the BeltMinder is to remind occasional wearers to wear safety belts all of the time. The following are reasons most often given for not wearing safety belts: (All statistics based on U.S. data) Reasons given... Consider ... “ Crashes are rare events ” 36700 crashes occur every day .
Reasons given... Consider ... “ I ’ d rather be thrown clear ” Not a good idea. People who are ejected are 40 times more likely to DIE. Safety belts help prevent ejection, WE CAN ’ T “ PICK OUR CRASH ” . Do not sit on top of a buckled safety belt to avoid the Belt Minder chime.
3. Buckle then unbuckle the safety belt three times, ending with the safety belt unbuckled. This can be done before or during BeltMinder warning activation. 4. T urn on the parklamps, turn off the parklamps. 5. Buckle then unbuckle the safety belt three times, ending with the safety belt unbuckled.
there are no nicks, tears or cuts. Replace if necessary . All safety belt assemblies, including retractors, buckles, front seat belt buckle assemblies, buckle support assemblies (slide bar -if equippe.
Important supplemental restraint system (SRS) precautions The supplemental restraint system is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries.
Modifications to the front end of the vehicle, including frame, bumper , front end body structure and tow hooks may affect the performance of the air bag sensors increasing the risk of injury .
collisions, not rollover , side-impact, or rear -impacts unless the collision causes sufficient longitudinal deceleration. The air bags inflate and deflate rapidly upon activation. After air bag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant.
The SRS consists of: • driver and passenger air bag modules (which include the inflators and air bags) • side air bags (if equipped). Refer to Side air bag system later in this chapter • safety .
Passenger front and side air bag ON/OFF switch An air bag ON/OFF switch has been installed in this vehicle. Before driving, always look at the face of the switch to be sure the switch is in the proper position in accordance with these instructions and warnings.
1. Insert the ignition key and turn the switch to ON. 2. The OFF light will briefly illuminate when the ignition is turned to ON. This indicates that the passenger front and side air bags are operational.
occupant is not properly buckled up. The most effective way to reduce the risk of unnecessary air bag injuries, without reducing the overall safety of the vehicle, is to make sure all occupants are properly restrained in the vehicle, especially in the front seat.
This vehicle has special energy management safety belts for the driver and right front passenger . These particular belts are specifically designed to work with air bags to help reduce the risk of injury in a collision.
This vehicle has special energy management safety belts for the driver and right front passenger . These particular belts are specifically designed to work with air bags to help reduce the risk of injury in a collision.
Do not place objects or mount equipment on or near the air bag cover on the side of the seatbacks of the front seats or in front seat areas that may come into contact with a deploying air bag. Failure to follow these instructions may increase the risk of personal injury in the event of a collision.
How does the side air bag system work? The side air bag system consists of the following: • An inflatable nylon bag (air bag) with a gas generator concealed behind the outboard bolster of the driver and front passenger seatbacks. • A special seat cover designed to allow air bag deployment.
Several air bag system components get hot after inflation. Do not touch them after inflation. If the side air bag has deployed, the air bag will not function again. The side air bag system (including the seat) must be inspected and serviced by a qualified technician in accordance with the vehicle service manual.
Disposal of air bags and air bag equipped vehicles (including pretensioners) For disposal of air bags or air bag equipped vehicles, see your local dealership or qualified technician.
Child booster seats Children outgrow a typical convertible or toddler seat when they weigh 40 pounds and are around 4 years of age. Although the lap/shoulder belt will provide some protection, these children are still too small for lap/shoulder belts to fit properly , which could increase the risk of serious injury .
T ypes of booster seats There are two types of belt-positioning booster seats: • Those that are backless. If your backless booster seat has a removable shield, remove the shield and use the lap/shoulder belt.
Follow all instructions provided by the manufacturer of the booster seat. Never put the shoulder belt under a child ’ s arm or behind the back because it eliminates the protection for the upper part of the body and may increase the risk of injury or death in a collision.
When installing a child safety seat: • Review and follow the information presented in the Air Bag Supplemental Restraint System section in this chapter . • Use the correct safety belt buckle for that seating position. • Insert the belt tongue into the proper buckle until you hear a snap and feel it latch.
1. Position the child safety seat in a seat with a combination lap and shoulder belt. 2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together . 3. While holding the shoulder and lap belt portions together , route the tongue through the child seat according to the child seat manufacturer ’ s instructions.
4. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) for that seating position until you hear a snap and feel the latch engage.
8. Allow the safety belt to retract to remove any slack in the belt. 9. Before placing the child in the seat, forcibly move the seat forward and back to make sure the seat is securely held in place. T o check this, grab the seat at the belt path and attempt to move it side to side and forward.
2. Locate the tether anchor at the bottom back of the passenger seat. 3. Route the child safety seat tether strap under the head restraint and over the back of the seat.
5. Rotate the tether strap. 6. Clip the tether strap to the anchor on the seat frame. 7. Rotate the tether strap clip. Seating and Safety Restraints 122.
8. T ighten the child safety seat tether strap according to the manufacturer ’ s instructions. Attaching child safety seats with Lower Anchor and T ethers for Children (LA TCH) attachments for child seat anchors Some child safety seats are labeled as LA TCH or LA TCH-compatible child seats.
The lower anchors for child seat installation are located at the rear section (as viewed from the front of the seat) of the passenger seat between the cushion and seat back. Follow the child seat manufacturer ’ s instructions to properly install safety seats with LA TCH lower anchors and LA TCH-compatible attachments.
STARTING Positions of the ignition 1. LOCK, locks the gearshift lever and allows key removal. (The steering wheel will not lock after key removal.) 2. OFF , shuts off the engine and all accessories except the radio, convertible top control and the power windows if accessory delay is active.
Extended idling at high engine speeds can produce very high temperatures in the engine and exhaust system, creating the risk of fire or other damage. Do not park, idle, or drive your vehicle in dry grass or other dry ground cover . The emission system heats up the engine compartment and exhaust system, which can start a fire.
5. T urn the key to 4 (RUN) without turning the key to 5 (ST ART). Make sure the corresponding lights illuminate or illuminate briefly . If a light fails to illuminate, have the vehicle serviced. • If the driver ’ s safety belt is fastened, the light may not illuminate.
4. When the engine starts, release the key , then release the accelerator pedal gradually as the engine speeds up. 5. After idling for a few seconds, apply the brake, shift into gear and drive.
Important ventilating information If the engine is idling while the vehicle is stopped in an open area for long periods of time, open the windows at least 2.5 cm (one inch). Adjust the heating or air conditioning (if equipped) to bring in fresh air . Improve vehicle ventilation by keeping all air inlet vents clear of snow , leaves and other debris.
The ABS operates by detecting the onset of wheel lockup during brake applications and compensates for this tendency . The wheels are prevented from locking even when the brakes are firmly applied.
Parking brake Apply the parking brake whenever the vehicle is parked. T o set the parking brake, apply the brake pedal and pull the handle up as far as possible. The BRAKE warning lamp in the instrument cluster illuminates and remains illuminated (when the ignition is turned to the RUN position) until the parking brake is released.
controlling wheel spin. The system borrows many of the electronic and mechanical elements already present in the anti-lock braking system (ABS). Wheel-speed sensors allow excess rear wheel spin to be detected by the T raction Control 娂 portion of the ABS computer .
Aggressive driving in any road conditions can cause you to lose control of your vehicle increasing the risk of severe personal injury or property damage.
If you cannot move the gearshift lever out of P (Park) with ignition in the RUN position and the brake pedal depressed: 1. Apply the parking brake, turn ignition key to LOCK, then remove the key . 2. Insert the key and turn it to OFF . Apply the brake pedal and shift to N (Neutral).
durability , and provide consistent shift feel over the life of the vehicle. It is normal for a new transmission to shift firmly . This operation is considered normal and will not affect function durability of the transmission.
R (Reverse) W ith the gearshift lever in R (Reverse), the vehicle will move backward. Always come to a complete stop before shifting into and out of R (Reverse). N (Neutral) W ith the gearshift lever in N (Neutral), the vehicle can be started and is free to roll.
Drive 5 (Overdrive) The normal driving position for the best fuel economy . T ransmission operates in gears One through Five. Drive 4 (Drive) T ransmission operates in gears One through Four . Drive 4 (Drive) provides engine braking in 4th gear and is useful when: • driving with a heavy load.
3 (Third) T ransmission operates in third gear only . Selecting 3 (Third) provides engine braking. Upshifts can be made by shifting to 4 (Drive) or 5 (Overdrive). Selecting 3 (Third) at higher speeds causes the transmission to shift to a lower gear , and will shift to 3 (Third) after vehicle decelerates to the proper speed.
1 (First) Use 1 (Low) to provide maximum engine braking on steep downgrades. Upshifts can be made by shifting to 2 (Second), 3 (Third), 4 (Drive) or 5 (Overdrive). Selecting 1 (Low) at higher speeds causes the transmission to shift to a lower gear , and will shift to 1 (Low) after vehicle decelerates to the proper speed.
• GVW (Gross V ehicle W eight): Base curb weight plus payload weight. The GVW is not a limit or a specification. • GVWR (Gross V ehicle W eight Rating): Maximum permissible total weight of the base vehicle, occupants, optional equipment and cargo.
cab), the weight added should not exceed the front axle reserve capacity (F ARC). Additional frontal weight may be added to the front axle reserve capacity provided you limit your payload in other ways (i.e. restrict the number of occupants or amount of cargo carried).
Do not exceed the maximum loads listed on the Certification label. For load specification terms found on the label, refer to V ehicle loading in this chapter . Remember to figure in the tongue load of your loaded trailer when figuring the total weight.
The braking system of the tow vehicle is rated for operation at the GVWR not GCWR. Trailer lamps T railer lamps are required on most towed vehicles. Make sure your trailer lamps conform to local and Federal regulations. See your dealer or trailer rental agency for proper instructions and equipment for hooking up trailer lamps.
Launching or retrieving a boat Disconnect the wiring to the trailer before backing the trailer into the water . Reconnect the wiring to the trailer after the trailer is removed from the water . When backing down a ramp during boat launching or retrieval: • do not allow the static water level to rise above the bottom edge of the rear bumper .
GETTING ROADSIDE ASSISTANCE T o fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program.
Canadian customers who require roadside assistance, call 1 – 800 – 665 – 2006. If you need to arrange roadside assistance for yourself, Ford Motor Company will reimburse a reasonable amount.
The fuel pump shut-off switch is located in the driver ’ s foot well, behind the kick panel. The reset button (RED) for the fuel pump shut-off switch is accessible through an opening in the kick panel. Use the following procedure to reset the fuel pump shut-off switch.
Note: Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire.
The fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 1 5A Starter relay coil 2 5A Radio start signal 3 5A ABS module 4 5A PCM coil, Cluster .
Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 13 5A Cluster 14 10A Air bag, V ehicle ID 15 5A Not used (spare) 16 5A Not used (spare) 17 5A Alternator and air bag wa.
Front power distribution box The front power distribution box is located in the engine compartment. The power distribution box contains high-current fuses that protect your vehicle ’ s main electrical systems from overloads. Always disconnect the battery before servicing high current fuses.
The high-current fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 1 10A* A/C clutch 2 15A* Heated wiper park 3 10A* Park lamp 4 15A* Horn 5 20A* Fuel .
Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 14 30A** ABS module power 15 — Not used 16 30A** Blower motor 17 — Not used 18 40A** PCM 19 — Not used 20 — Not used 21 3.
Rear power distribution box The rear power distribution box is located in the luggage compartment under the spare tire well cover . The power distribution box contains high-current fuses that protect your vehicle ’ s main electrical systems from overloads.
The high-current fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 1 15A* Decklid solenoid 2 5A* License plate lamp 3 10A* Left rear turn and stop lamp.
Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 31 — Not used 32 30A** SSP2 Relay 001 Full ISO SSP1 Relay 002 Full ISO SSP4 Relay 003 Full ISO Rear defroster Relay 004 Full IS.
• tow a trailer • use tire chains • drive through an automatic car wash, because of the vehicle ’ s reduced ground clearance • try to repair the temporary spare tire or remove it from its wh.
3. Lift the trunk cargo cover and remove the spare tire, jack and tool bag with lug wrench. 4. Loosen each wheel lug nut one-half turn counterclockwise but do not remove them until the wheel is raised off the ground.
5. Put the jack in the jack notch next to the tire you are changing. T urn the jack handle clockwise until the wheel is completely off the ground. Never use the rear differential as a jacking point. T o lessen the risk of personal injury , do not put any part of your body under the vehicle while changing a tire.
9. Remove the jack and fully tighten the lug nuts in the order shown. Note: The jack cannot be properly stowed when a full size tire is placed here. Secure the jack and the temporary spare tire as shown after the flat tire has been fixed. 10. Put flat tire, jack away .
T o remove the anti-theft lug nut: 1. Insert the key over the locking lug nut. Make sure you hold the key square to the lug nut. If you hold the key at an angle, you could damage the key and the lug nut. 2. Place the lug nut wrench over the lug nut key and apply pressure on the key with the wrench.
3. Park the booster vehicle close to the trunk of your disabled vehicle making sure the two vehicles do not touch. Set the parking brake on both vehicles and stay clear of the engine cooling fan and other moving parts. 4. Check all battery terminals and remove any excessive corrosion before you attach the battery cables.
3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery . 4. Make the final connection of the negative (-) cable to the spare tire tie-down stud. (Y our vehicle may be equipped with a plastic cap on top of the tire tie-down stud.
Do not connect the end of the second cable to the negative (-) terminal of the battery to be jumped. A spark may cause an explosion of the gases that surround the battery . 5. Ensure that the cables are clear of fan blades, belts, moving parts of both engines, or any fuel delivery system parts.
2. Remove the jumper cable on the negative (-) connection of the booster vehicle ’ s battery . 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle ’ s battery .
4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle ’ s battery . After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle conditions.
WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or , if you are a member of a roadside assistance program, your roadside assistance service provider . It is recommended that your vehicle be towed with a wheel lift or flatbed equipment.
GETTING THE SERVICES YOU NEED At home Ford Motor Company and Ford of Canada have authorized dealerships to service your vehicle. It is preferred that you return to the authorized dealer where your vehicle was purchased when warranty repairs are needed.
In Canada: Customer Relationship Centre Ford Motor Company of Canada, Limited P .O. Box 2000 Oakville, Ontario L6J 5E4 1-800-565-3673 (FORD) www .ford.
In some states (in the U.S.) you must directly notify Ford in writing before pursuing remedies under your state ’ s warranty laws. Ford is also allowed a final repair attempt in some states.
THE DISPUTE SETTLEMENT BOARD (U.S. ONLY) The Dispute Settlement Board is: • an independent, third-party arbitration program for warranty disputes. • available free to owners and lessees of qualifying Ford Motor Company vehicles. The Dispute Settlement Board may not be available in all states.
Board membership The Board consists of: • Three consumer representatives • A Ford or Lincoln Mercury dealership representative Consumer candidates for Board membership are recruited and trained by an independent consulting firm.
Oral presentations If you would like to make an oral presentation, indicate YES to question 6 on the application. While it is your right to make an oral presentation before the Board, this is not a requirement and the Board will decide the case whether or not an oral presentation is made.
UTILIZING THE MEDIATION/ARBITRATION PROGRAM (CANADA ONLY) In those cases where you continue to feel that the efforts by Ford and the dealer to resolve a factory-related vehicle service concern have be.
If your vehicle must be serviced while you are traveling or living in Central or South America, the Caribbean, or the Middle East, contact the nearest Ford dealership. If the dealership cannot help you, write or call: FORD MOTOR COMP ANY WORLDWIDE DIRECT MARKET OPERA TIONS 1555 Fairlane Drive Fairlane Business Park #3 Allen Park, Michigan 48101 U.
IN CALIFORNIA (U.S. ONLY) California Civil Code Section 1793.2(d) requires that, if a manufacturer or its representative is unable to repair a motor vehicle to conform to the vehicle ’ s applicable .
REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway T raffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company .
W ASHING THE EXTERIOR W ash your vehicle regularly with cool or lukewarm water and a neutral Ph shampoo, such as Motorcraft Detail W ash (ZC-3 – A), which is available from your dealer . • Never use strong household detergents or soap, such as dish washing or laundry liquid.
PAINT CHIPS Y our dealer has touch-up paint and sprays to match your vehicle ’ s color . T ake your color code (printed on a sticker in the driver ’ s door jam) to your dealer to ensure you get the correct color .
• Cover the highlighted areas to prevent water damage when cleaning the engine. • Never wash or rinse the engine while it is running; water in the running engine may cause internal damage. PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts.
• Do not use abrasives, as they may cause scratches. • Do not use fuel, kerosene, or paint thinner to clean any parts. • W iper blades can be cleaned with isopropyl (rubbing) alcohol or windshield washer solution. Be sure to replace wiper blades when they appear worn or do not function properly .
INTERIOR For fabric, carpets, cloth seats, safety belts and seats equipped with side air bags: • Remove dust and loose dirt with a vacuum cleaner . • Remove light stains and soil with Ford Extra Strength Upholstery Cleaner (E8AZ-19523 – AA).
FORD, LINCOLN AND MERCURY CAR CARE PRODUCTS Y our Ford, Lincoln or Mercury dealer has many quality products available to clean your vehicle and protect its finishes. These quality products have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and appearance of your vehicle.
SERVICE RECOMMENDATIONS T o help you service your vehicle: • W e highlight do-it-yourself items in the engine compartment for easy location. • W e provide a scheduled maintenance guide which makes tracking routine service easy . If your vehicle requires professional service, your dealership can provide the necessary parts and service.
Working with the engine on 1. Set the parking brake and ensure the gearshift is securely latched in P (Park). 2. Block the wheels to prevent the vehicle from moving unexpectedly . Note: Do not start your engine with the air cleaner removed and do not remove it while the engine is running.
IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 3.9L – 4V V8 engine 1. Engine oil filler cap 2. Engine oil dipstick 3. Brake fluid reservoir 4. Engine coolant reservoir 5. Power steering fluid reservoir 6. Air filter assembly 7. W indshield washer fluid reservoir 8.
Check the washer fluid whenever you stop for fuel. The reservoir is highlighted with a symbol. Add fluid to fill the reservoir if the level is low . In very cold weather , do not fill the reservoir completely . Only use a washer fluid that meets Ford specification ESR-M17P5 – A.
5. Locate and carefully remove the engine oil level indicator (dipstick). 6. W ipe the indicator clean. Insert the indicator fully , then remove it again. • If the oil level is between the MIN and MAX marks, the oil level is acceptable. DO NOT ADD OIL.
2. If the engine oil level is not within the normal range, add only certified engine oil of the recommended viscosity . Remove the engine oil filler cap and use a funnel to pour the engine oil into the opening. 3. Recheck the engine oil level. Make sure the oil level is not above the MAX mark on the engine oil level indicator (dipstick).
BATTERY Y our vehicle is equipped with a Motorcraft maintenance-free battery which is located in the luggage compartment, next to the spare tire. Y our battery is designed to purge any battery gases to the outside of the vehicle by means of a vent hose.
When lifting a plastic-cased battery , excessive pressure on the end walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery . Lift the battery with a battery carrier or with your hands on opposite corners.
If the battery has been disconnected or a new battery has been installed, the short drop glass, clock and the preset radio stations must be reset once the battery is reconnected. • Always dispose of automotive batteries in a responsible manner . Follow your local authorized standards for disposal.
When the engine is cold, check the level of the engine coolant in the reservoir . • The engine coolant should be at the “ cold fill level ” or within the “ cold fill range ” as listed on the engine coolant reservoir (depending upon application).
Do not add engine coolant when the engine is hot. Steam and scalding liquids released from a hot cooling system can burn you badly . Also, you can be burned if you spill coolant on hot engine parts. Do not put engine coolant in the windshield washer fluid container .
• Do not add extra inhibitors or additives to the coolant. These can be harmful and compromise the corrosion protection of the engine coolant. • Do not mix with recycled coolant unless from a Ford-approved recycling process (see Use of Recycled engine coolant section).
If you have to add more than 1.0 liter (1.0 quart) of engine coolant per month, have your dealer check the engine cooling system. Y our cooling system may have a leak. Operating an engine with a low level of coolant can result in engine overheating and possible engine damage.
What you should know about fail-safe cooling If the engine coolant supply is depleted, this feature allows the vehicle to be driven temporarily before incremental component damage is incurred. The “ fail-safe ” distance depends on ambient temperatures, vehicle load and terrain.
4. Check the coolant level and replenish if low . Never remove the coolant reservoir cap while the engine is running or hot. 5. Re-start the engine and take your vehicle to a service facility . Driving the vehicle without repairing the engine problem increases the chance of engine damage.
WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELS Important safety precautions Do not overfill the fuel tank. The pressure in an overfilled tank may cause leakage and lead to fuel spray and fire.
• A void getting fuel liquid in your eyes. If fuel is splashed in the eyes, remove contact lenses (if worn), flush with water for 15 minutes and seek medical attention. Failure to seek proper medical attention could lead to permanent injury . • Fuels can also be harmful if absorbed through the skin.
Fuel Filler Cap Y our fuel tank filler cap has an indexed design with a 1/8 turn on/off feature. When fueling your vehicle: 1. T urn the engine off. 2. Carefully turn the filler cap counterclockwise 1/8 of a turn until it stops. 3. Pull to remove the cap from the fuel filler pipe.
Octane recommendations Y our vehicle is designed to use “ Premium ” unleaded gasoline with an (R+M)/2 octane rating of 91 or higher for optimum performance.
Running out of fuel A void running out of fuel because this situation may have an adverse affect on powertrain components. If you have run out of fuel: • Y ou may need to cycle the ignition from OFF to ON several times after refueling, to allow the fuel system to pump the fuel from the tank to the engine.
The amount of usable fuel in the empty reserve varies and should not be relied upon to increase driving range. When refueling your vehicle after the fuel gauge indicates empty , you might not be able to refuel the full amount of the advertised capacity of the fuel tank due to the empty reserve still present in the tank.
Driving style — good driving and fuel economy habits Give consideration to the lists that follow and you may be able to change a number of variables and improve your fuel economy . Habits • Smooth, moderate operation can yield up to 10% savings in fuel.
Conditions • Heavily loading a vehicle or towing a trailer may reduce fuel economy at any speed. • Carrying unnecessary weight may reduce fuel economy (approximately 0.
• Do not turn off the ignition while your vehicle is moving, especially at high speeds. • Have the items listed in your scheduled maintenance guide performed according to the specified schedule.
If the vehicle ’ s powertrain system or its battery has just been serviced, the on-board diagnostics system is reset to a “ not ready for I/M test ” condition.
BRAKE FLUID Checking and adding brake fluid Brake fluid should be checked and refilled as needed. Refer to the scheduled maintenance guide for the service interval schedules. 1. Clean the reservoir cap before removal to prevent dirt or water from entering the reservoir .
T RANSMISSION FLUID Checking automatic transmission fluid The 5R55N transmission does not have a transmission fluid dipstick. Refer to your scheduled maintenance guide for scheduled intervals for fluid checks and changes. Y our transmission does not consume fluid.
Changing the air filter element 1. Loosen the hose clamp on the outlet tube at the air filter housing. 2. Release the two clamps that secure the cover to the air filter housing and place the cover aside.
3. Remove the air filter element from the air filter housing. 4. W ipe the air filter housing and cover clean to remove any dirt or debris and to ensure good sealing. 5. Install a new air filter element. Be careful not to crimp the filter element edges between the air filter housing and cover .
T readwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half (1 1/2) times as well on the government course as a tire graded 100.
SERVICING YOUR TIRES Checking the tire pressure • Use an accurate tire pressure gauge. • Check the tire pressure when tires are cold, after the vehicle has been parked for at least one hour or has been driven less than 5 km (3 miles).
Replacing the tires Replace the tires when the wear band is visible through the tire treads. When replacing full size tires, never mix radial bias-belted, or bias-type tires. Use only the tire sizes that are listed on the Certification or T ire Label.
The use of snow cables is not recommended for this vehicle, as damage to your vehicle may occur under extreme handling or rough road conditions. However , if you choose to operate the vehicle with snow cables, avoid these conditions and follow the manufacturer ’ s recommendations.
Fluid Ford Part Name Application Capacity Engine coolant 2 Motorcraft Premium Engine Coolant (green-colored) or Motorcraft Premium Gold Engine Coolant (yellow-colored) 3.
be changed any time the rear axle has been submerged in water . Fill 6 mm to 14 mm (1/4 inch to 9/16 inch) below bottom of fill hole. 4 Ensure the correct automatic transmission fluid is used. MERCON 威 and MERCON 威 V are not interchangeable. DO NOT MIX MERCON 威 and MERCON 威 V .
Item Ford part name Ford part number Ford specification Engine oil Motorcraft SAE 5W -20 Premium Synthetic Blend Motor Oil XO-5W20-QSP WSS-M2C153-H with API Certification Mark Lock cylinders Motorcraf.
ENGINE DATA Engine 3.9L-4V V8 engine Displacement 3 949 cc (241 cid) Required fuel 91 octane Firing order 1-5-4-2-6-3-7-8 Spark plug gap 0.99-1.09 mm (0.039-0.043 inch) Ignition system Coil on plug Compression ratio 10.55:1 VEHICLE DIMENSIONS V ehicle dimensions mm (in) (1) Overall length 4732mm (186.
IDENTIFYING YOUR VEHICLE Certification label The National Highway T raffic Safety Administration Regulations require that a Certification label be affixed to a vehicle and prescribe where the Certification label may be located. The Certification label is located on the front door latch pillar on the driver ’ s side.
V ehicle identification number (VIN) The vehicle identification number is attached to a metal tag and is located on the driver side instrument panel. (Please note that in the graphic XXXX is representative of your vehicle identification number .) 1. W orld manufacturer identifier 2.
FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of genuine Ford accessories are available for your vehicle through your local authorized Ford, Lincoln, Mercury or Ford of Canada dealer .
Carpet floor mats First aid kit Front end cover Highway safety kit Locking gas cap For maximum vehicle performance, keep the following information in mind when adding accessories or equipment to your .
A ABS (see Brakes) ..................... 129 Accessory delay .......................... 57 Air bag supplemental restraint system ........................ 100 – 101, 109 and child safety seats ............ 102 description ......................101, 109 disposal .
attaching with tether straps ....................................... 120 in front seat ............................ 117 in rear seat .............................. 117 LA TCH ..................................... 123 Cleaning your vehicle engine compartment .
idle speed control ................... 190 lubrication specifications .................. 218, 220 refill capacities ........................ 216 service points .......................... 186 starting after a collision ......... 146 Engine block heater .
replacing bulbs ......................... 48 turning on and off .................... 43 warning chime .......................... 13 Heating heating and air conditioning system ....................................... 30 Hood ...........................
Lumbar support, seats ............... 88 M Manual transmission fluid capacities ........................ 216 lubricant specifications .......... 220 Master lighting switch ................ 43 Mirrors side view mirrors (power) .......58 Motorcraft parts .
Spark plugs, specifications ..................... 216, 220 Specification chart, lubricants ...........................218, 220 Speed control ..............................59 Speedometer ............................... 15 Starting your vehicle ........
231.
232.
Een belangrijk punt na aankoop van elk apparaat Ford 2002 Thunderbird (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Ford 2002 Thunderbird heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Ford 2002 Thunderbird vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Ford 2002 Thunderbird leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Ford 2002 Thunderbird krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Ford 2002 Thunderbird bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Ford 2002 Thunderbird kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Ford 2002 Thunderbird . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
