Gebruiksaanwijzing /service van het product 2004 Mustang van de fabrikant Ford
Ga naar pagina of 16
Introduction 2 Instrumentation 4 Servicing your vehicle 5 All rights reserved. Reproduction by any means, electronic or mechanical including photocopying, recording or by any information storage and retrieval system or translation in whole or part is not permitted without written authorization from Ford Motor Company .
ABOUT THIS SUPPLEMENT This booklet supplements your Owner Guide and is part of the owner’ s portfolio. It describes the operation of your natural gas vehicle (NGV) and how it differs from a standard gasoline powered vehicle.
COMPRESSED NATURAL GAS (CNG) FUEL SYSTEM Y our vehicle is equipped with a dedicated compressed natural gas (CNG) fuel system that is under high pressure. Depending upon the application, the CNG fuel system is rated at a pressure of 20,700 kPa (3,000 psi) at 21 ° C (70 ° F) or 24,800 kPa (3,600 psi) at 21 ° C (70 ° F).
FUEL GAUGE The fuel gauge in your NGV behaves similarly to a typical gasoline fuel gauge. However , the gauge operation is based on the pressure and temperature of the natural gas, not on the level of liquid gasoline.
CNG FUEL SYSTEM COMPONENT IDENTIFICATION The following illustrations depict the major unique components of the CNG fuel system. All of these unique components are constructed of special materials that withstand the effects of CNG.
E-450 Cutaway 1. Fuel rail sensors - An injection pressure sensor and an engine fuel temperature sensor provide engine fuel information to the powertrain control module. 2. Isolation solenoid valve - Blocks fuel flow from supply line to injection manifold when the engine is off.
9. Aft axle fuel tanks - T wo steel fuel tanks located behind the rear axle. 10. Midship fuel tank - A steel fuel tank located underbody . 11. High pressure fuel lines - Delivers high pressure fuel to the fuel tanks and fuel pressure regulator .
vehicle ’ s inertia switch. If the engine cranks but does not start after a collision, the fuel solenoid valve inertia switch may have been activated. The inertia switch is a device intended to close the fuel solenoid valve when your vehicle has been involved in a substantial jolt.
2. Isolation solenoid valve - Blocks flow from the injection manifold when the engine is off. 3. Engine - Is a modified 4.6L engine with Sequential Electronic Fuel Injection (SEFI) and increased compression ratio. 4. Engine coolant lines - Provide required heat to high pressure regulator .
ADAPTERS DO NOT use fuel receptacle adapters when refueling your vehicle. The profiles of both the natural gas vehicle receptacle and the fuel station nozzles are specified by ANSI/AGA NGV1-1994, CGA NGV1-M94. These profiles are specified for compressed natural gas vehicles and fuel stations for safety purposes.
indication that refueling is nearly complete. Also, the station compression equipment may turn on at any time during the refueling process. FUEL QUALITY Do not use liquefied natural gas (LNG) or a CNG that is derived from a process such as flashing (heating LNG).
SERVICING YOUR NATURAL GAS VEHICLE Service to the CNG fuel system should be conducted at a qualified dealership by a trained NGV technician only . Failure to do so may cause damage to components or cause bodily harm. FUELING Do not fuel your vehicle with the ignition on the ON position.
Use caution when fueling your vehicle. Make sure the engine is turned off and all flammable material is extinguished. Observe all Dispensing Equipment Safety Standards and Operating Procedures. The procedure is the same for both fast-fill and slow-fill fueling.
E-Series Cutaway 158 ” Wheelbase (3600 psi) Fueling method Standard tanks W ith Extended Range - One In-body T ank W ith Extended Range - T wo In-body T anks Slow-fill 63.2L (16.7 gallons) 96.1L (25.4 gallons) 128.7 (34.0 gallons) Fast-fill 53.8L (14.
Crown V ictoria (3600 psi) Fueling method Standard tanks W ith extended range system 1 Slow-fill 45.0L (11.9 gallons) 59.1L (15.6 gallons) Fast-fill 38.
The purpose of the inspection is to check for exterior damage to the tank which would shorten its usable life span. This inspection should only be done by qualified NGV Ford service technicians. The expiration date for the tank replacement is stated on each tank label See instructions on fuel container for inspection and service life.
Een belangrijk punt na aankoop van elk apparaat Ford 2004 Mustang (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Ford 2004 Mustang heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Ford 2004 Mustang vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Ford 2004 Mustang leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Ford 2004 Mustang krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Ford 2004 Mustang bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Ford 2004 Mustang kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Ford 2004 Mustang . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
