Gebruiksaanwijzing /service van het product 2005 Grand Marquis van de fabrikant Ford
Ga naar pagina of 264
Introduction 4 Instrument Cluster 10 W arning and control lights 10 Gauges 15 Entertainment Systems 20 AM/FM stereo 20 AM/FM stereo cassette 22 AM/FM stereo with CD 25 AM/FM stereo cassette with CD 28.
Seating and Safety Restraints 95 Seating 95 Safety restraints 100 Airbags 114 Child restraints 125 Tires, Wheels and Loading 136 T ire Information 136 Changing tires 141 Lug Nut T orque 147 V ehicle l.
Maintenance and Specifications 216 Engine compartment 217 Engine oil 218 Battery 222 Engine Coolant 224 Fuel information 230 Air filter(s) 244 Part numbers 245 Refill capacities 246 Lubricant specifications 247 Accessories 253 Index 255 All rights reserved.
CALIFORNIA Proposition 65 W arning W ARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
SAFETY AND ENVIRONMENT PROTECTION W arning symbols in this guide How can you reduce the risk of personal injury to yourself or others? In this guide, answers to such questions are contained in comments highlighted by the warning triangle symbol. These comments should be read and observed.
SPECIAL NOTICES Emission warranty The New V ehicle Limited W arranty includes Bumper -to-Bumper Coverage, Safety Restraint Coverage, Corrosion Coverage, and 6.0L Power Stroke Diesel Engine Coverage. In addition, your vehicle is eligible for Emissions Defect and Emissions Performance W arranties.
Special instructions For your added safety , your vehicle is fitted with sophisticated electronic controls. Please read the section Supplemental restraint system (SRS) in the Seating and Safety Restraints chapter . Failure to follow the specific warnings and instructions could result in personal injury .
These are some of the symbols you may see on your vehicle. V ehicle Symbol Glossary Safety Alert See Owner’ s Guide Fasten Safety Belt Air Bag-Front Air Bag-Side Child Seat Child Seat Installation W.
V ehicle Symbol Glossary Power W indows Front/Rear Power W indow Lockout Child Safety Door Lock/Unlock Interior Luggage Compartment Release Symbol Panic Alarm Engine Oil Engine Coolant Engine Coolant .
W ARNING LIGHTS AND CHIMES Standard instrument cluster Optional instrument cluster W arning lights and gauges can alert you to a vehicle condition that may become serious enough to cause expensive repairs. A warning light may illuminate when a problem exists with one of your vehicle’ s functions.
Maintenance and Specifications chapter . If the light is blinking, engine misfire is occurring which could damage your catalytic converter . Drive in a moderate fashion (avoid heavy acceleration and deceleration) and have your vehicle serviced immediately .
Driving a vehicle with the brake system warning light on is dangerous. A significant decrease in braking performance may occur . It will take you longer to stop the vehicle.
Never remove the coolant reservoir cap while the engine is running or hot. T raction control 娂 AdvanceT rac 威 active (if equipped): Illuminates when the T raction control 娂 system is active. It will be lit for a minimum of four seconds or for the duration of the T raction Control 娂 event, refer to the Driving chapter for more information.
T urn signal: Illuminates when the left or right turn signal or the hazard lights are turned on. If the indicators stay on or flash faster , check for a burned out bulb. High beams: Illuminates when the high beam headlamps are turned on. MESSAGE CENTER INDICATOR LIGHTS (IF EQUIPPED) Speed control: Illuminates when the speed control is activated.
Key-in-ignition warning chime: Sounds when the key is left in the ignition in the OFF/LOCK or ACCESSORY position and the driver’ s door is opened. GAUGES Standard instrument cluster gauges 2005 Crow.
Optional instrument cluster gauges Speedometer: Indicates the current vehicle speed. • Standard instrument cluster • Optional instrument cluster Engine coolant temperature gauge: • Standard inst.
• Optional instrument cluster Indicates engine coolant temperature. At normal operating temperature, the needle will be in the normal range (between “H” and “C”).
T rip odometer: Registers the miles (kilometers) of individual journeys. • Standard instrument cluster T o reset, depress the control. • Optional instrument cluster Refer to Electronic Message Center in the Driver Controls chapter for T rip A and T rip B features.
Engine oil pressure gauge (if equipped): Indicates engine oil pressure. The needle should stay in the normal operating range (between “L” and “H”). If the needle falls below the normal range, stop the vehicle, turn off the engine and check the engine oil level.
AM/FM STEREO (IF EQUIPPED) 1. Seek: Press / to find the next strong station down/up the frequency band. 2. T une: Press / to manually change radio frequency down/up.
5. Power/volume: Press to turn ON/OFF; turn to increase or decrease volume levels. 6. T one: Press TONE until the desired level — Bass, T reble, Fade appears on the display . T urn the volume control to raise/lower the levels, or to move the audio sound from the right to left or the front to back (if equipped).
AM/FM STEREO CASSETTE (IF EQUIPPED) 1. Balance: Press to shift sound to the left/right speakers. 2. Fade: Press to shift sound to the rear/front speakers. 3. CLK: T o set the hour , press and hold CLK. Then press SEEK to decrease or increase the hours.
next selection). Then, press REW (for the beginning of the current selection) or FF (to advance to the next selection). The tape MUST have a blank section of at least four seconds duration between programs. 5. Side 1–2: Press to change tape direction.
13. AM/FM: Press to choose a frequency band in radio mode. 14. Bass: Press / to decrease/increase the bass output. 15. T reble: Press / to decrease/increase the treble output. 16. EJ (Eject): Press to eject a tape. 17. Cassette door: Insert a cassette into the cassette door .
AM/FM STEREO SINGLE CD PREMIUM AUDIO SYSTEM (IF EQUIPPED) 1. CD slot: Insert a CD, label side up. W ith the ignition on, the radio will begin play when a CD is inserted. If the ignition is off, press CD prior to inserting a disc. Do not force a disc into the system as damage could result.
5. Eject: Press to eject the CD. If the disc is not removed within the allotted time, the system will automatically reload the CD and begin play . Note: The eject function will work when the ignition is turned off. 6. BASS: Press BASS; then press SEL to decrease/increase the level of bass output.
When activated, AUTOSET will momentarily appear in the display when any of the preset controls are pressed. Speed sensitive volume: Radio volume changes automatically and slightly with vehicle speed to compensate for road and wind noise. Recommended level is 1–3.
16. SCAN: Press SCAN to hear a brief sampling of radio stations or CD tracks. Press again to stop. PREMIUM/AUDIOPHILE SATELLITE COMPATIBLE AM/FM STEREO SINGLE CD/CASSETTE SYSTEM (IF EQUIPPED) 1. CD slot: Insert a CD, label side up. W ith the ignition on, the radio will begin to play a CD once inserted.
3. BASS: Press BASS; then press SEL-TEXT to decrease/increase the level of bass output. TREB (T reble): Press TREB; then press SEL-TEXT to decrease/increase the level of treble output. 4. BAL (Balance): Press BAL; then press SEL-TEXT to shift sound to the left/right speakers.
stations are independently operated and individually elect to use RDS technology to transmit station ID and program type as desired. FIND Program type: Allows you to search RDS-equipped stations for a certain category of music format: Classic, Country , Info, Jazz, Oldies, R&B, Religious, Rock, Soft, T op 40.
Dolby: W orks in tape mode to reduces tape noise and hiss. Press MENU until DOLBY XX appears in the display . Press SEL-TEXT to toggle ON/OFF . The Dolby 威 noise reduction system is manufactured under license from Dolby Laboratories Licensing Corporation.
13. SCAN: Press SCAN to hear a brief sampling of radio stations, selections or CD tracks. Press again to stop. 14. SHUF (Shuffle): Press to play the tracks on the current CD in random order . Press again to stop. 15. Memory presets: T o set a station: Select frequency band, tune to a station, press and hold a preset button until sound returns.
AUDIOPHILE AM/FM STEREO IN-DASH SIX CD SOUND SYSTEM (IF EQUIPPED) 1. CD slot: T o insert a CD, press LOAD. When the system is ready , insert a CD, label side up. 2. SEEK: Press to access the next/previous radio station or CD track. Press and hold to advance/reverse in the current CD track.
4. MUTE: Press to mute the playing media. Press again to return to the playing media or turn the volume control to adjust the volume. 5. Eject: Press to eject CD(s) when the ignition is on or off. Numbers will illuminate in the display indicating which CD slots are loaded with CDs.
9. MENU: Press MENU repeatedly to access RDS on/off. Use SEL-TEXT to toggle RDS on/off. Press MENU again to access Program type mode or Show T ype mode.
Speed sensitive volume: Radio volume changes automatically and slightly with vehicle speed to compensate for road and wind noise. Recommended level is 1–3. Level 0 turns the feature off and level 7 is the maximum setting. Press MENU to access and use SEL-TEXT to adjust the volume setting.
RADIO FREQUENCIES AM and FM frequencies are established by the Federal Communications Commission (FCC) and the Canadian Radio and T elecommunications Commission (CRTC). Those frequencies are: AM - 530, 540–1700, 1710 kHz FM- 87.7, 87.9–107.7, 107.
CD/CD PLAYER CARE Do: • Handle discs by their edges only . Never touch the playing surface. • Inspect discs before playing. Clean only with an approved CD cleaner and wipe from the center out. Don’t: • Expose discs to direct sunlight or heat sources for extended periods of time.
MANUAL HEATING AND AIR CONDITIONING SYSTEM (IF EQUIPPED) 1. Fan speed adjustment: Controls the volume of air circulated in the vehicle. 2. T emperature selection: Controls the temperature of the airflow in the vehicle. 3. Air flow selections: Controls the direction of the airflow in the vehicle.
T o aid in side window defogging/demisting in cold weather: 1. Select NORM A/C. 2. Adjust the temperature control to maintain comfort. 3. Set the fan speed to HI.
3. Fan speed: T urn to manually increase or decrease fan speed. 4. Defrost: Distributes outside air through the windshield defroster vents and the side window demisters. 5. Floor/defrost: Distributes outside air through the windshield defroster vents, floor vents and the side window demisters.
• Remove any snow , ice or leaves from the air intake area at the base of the windshield. T o aid in side window defogging/demisting in cold weather: 1. Select NORM A/C. 2. Adjust the temperature control to maintain comfort. 3. Set the fan speed to HI.
HEADLAMP CONTROL T urns the lamps off. T urns on the parking lamps, instrument panel lamps, license plate lamps and tail lamps. T urns the headlamps on. Autolamp control The autolamp system provides light sensitive automatic on-off control of the exterior lights normally controlled by the headlamp control.
Always remember to turn on your headlamps at dusk or during inclement weather . The Daytime Running Light (DRL) System does not activate your tail lamps and generally may not provide adequate lighting during these conditions. Failure to activate your headlamps under these conditions may result in a collision.
Domelamp Control The panel dimmer control also controls the domelamp operation. • Rotate the thumbwheel fully to the right, past detent to activate the domelamp. • In order to turn off the domelamp, rotate the thumbwheel to the left. AIMING THE HEADLAMPS The headlamps on your vehicle are properly aimed at the assembly plant.
W ith overhead console W ith overhead console and moon roof T o turn on the map lamps, press the map lamp control. REAR COURTESY/READING LAMPS Rotate the lens to illuminate the lamp. W ith the lens in the flat position, the courtesy lamp lights when: • Any door is opened.
Replacing exterior bulbs Check the operation of all the bulbs frequently . Using the right bulbs Replacement bulbs are specified in the chart below . Headlamp bulbs must be marked with an authorized “D.O.T .” for North America and an “E” for Europe to assure lamp performance, light brightness and pattern and safe visibility .
3. Disconnect the electrical connector from the bulb by pulling rearward. 4. Remove the bulb retaining ring by rotating it counterclockwise (when viewed from the rear) to free it from the bulb socket, and slide the ring off the plastic base. Keep the ring to retain the new bulb.
5. T urn the headlamps on and make sure they work properly . If the headlamp was correctly aligned before you changed the bulb, you should not need to align it again. Replacing front parking lamp/turn signal bulbs The park/turn lamp bulbs can be replaced without removing the headlamp assembly .
1. Make sure headlamp switch is in OFF position, then open the trunk and remove plastic retainer to expose the lamp assembly hardware. 2. Carefully pull the carpet away to expose the plastic retainer . 3. Remove three nut and washer assemblies and the lamp assembly from the vehicle.
Replacing license plate lamp bulbs 1. Make sure headlamp switch is in OFF position, then remove two screws, grommets and the license plate lamp assembly from the trunk lid.
3. Carefully pull the bulb socket out of the lamp assembly . 4. Pull the bulb straight out of the socket and push in the new bulb. T o install, reverse the removal procedure. Overhead console lamps T o remove and replace the lamps in the overhead console: 1.
MULTI-FUNCTION LEVER W indshield wiper: Rotate the end of the control away from you to increase the speed of the wipers; rotate towards you to decrease the speed of the wipers. W indshield washer: Push the end of the stalk: • briefly: causes a single swipe of the wipers without washer fluid.
Poor wiper quality can sometimes be improved by cleaning the wiper blades, refer to Windows and wiper blades in the Cleaning chapter . T o prolong the life of the wiper blades, it is highly recommended to scrape off the ice on the windshield before turning on the wipers.
Slide on rod feature (if equipped) Rotate the visor towards the side window and extend it rearward for additional sunlight coverage. Note: T o stow the visor back into the headliner , visor must be retracted before moving it back towards the windshield.
3. Press and hold the MODE control until V AR appears in the display , then release. The display should show the current zone number . 4. Press the MODE control until the desired zone number appears. The display will flash and then return to normal operation.
3. From a blank display press and release the MODE button once. The directional heading will be displayed. Note: If the compass is de-calibrated, CAL will be displayed in the right corner of the display . Refer to “Calibration mode” in this section for more details.
4. Determine which magnetic zone you are in by referring to the zone map. 5. Repeatedly press and release the RESET button to scroll through the zones 1–15 until the desired zone is displayed. 6. Press the MODE button to save the new zone setting and return to the compass normal mode.
4. Press the RESET button to de-calibrate the compass. The display will read CIRCLE SLOWL Y TO CALIBRA TE for a few seconds and then display a direction with CAL displayed on the right side. 5. Drive the vehicle in a tight circle in a magnetically clean area such as an open parking lot.
Programming Do not program the HomeLink 威 with the vehicle parked in the garage. Note: Some vehicles may require the ignition switch to be turned to the second (or “ACC”) position for programming and/or operation of the HomeLink 威 .
3. Simultaneously press and hold both the HomeLink 威 and hand-held transmitter button. The message CHANNEL “X” (1,2 or 3) TRAINING will appear on the display .
If the indicator light(s) underneath the house icon blink rapidly for two seconds and then turn to a continuous light, proceed with steps 6 through 8 to complete programming of a rolling code equipped device.
Operating the HomeLink 姞 Wireless Control System T o operate, simply press and release the appropriate HomeLink 威 button. Activation will now occur for the trained product (garage door , gate operator , security system, entry door lock, or home or office lighting etc.
1. Press and hold the desired HomeLink 威 button. DO NOT release the button. The display will read CHANNEL “X” (1,2 or 3) TRANSMIT 2. The display will change to CHANNEL “X” (1,2, or 3) TRAINING after 20 seconds. W ithout releasing the HomeLink 威 button, follow step 2 in the “Programming” section.
POWER WINDOWS Do not leave children unattended in the vehicle and do not let children play with the power windows. They may seriously injure themselves. When closing the power windows, you should verify they are free of obstructions and ensure that children and/or pets are not in the proximity of the window openings.
POWER SIDE VIEW MIRRORS T o adjust your mirrors: 1. Select to adjust the left mirror or to adjust the right mirror . 2. Move the control in the direction you wish to tilt the mirror .
(darkened) state when bright lights (glare) reach the mirror . When the mirror detects bright light from behind the vehicle, it will automatically adjust (darken) to minimize glare. The mirror will automatically return to the normal state whenever the vehicle is placed in R (Reverse) to ensure a bright clear view when backing up.
Setting speed control The controls for using your speed control are located on the steering wheel for your convenience. 1. Press the ON control and release it. 2. Accelerate to the desired speed. 3. Press the SET + control and release it. 4. T ake your foot off the accelerator pedal.
Resuming a set speed Press the RESUME control and release it. This will automatically return the vehicle to the previously set speed. The RESUME control will not work if the vehicle speed is not faster than 30 mph (48 km/h).
• Depress the brake pedal until the desired vehicle speed is reached, press the SET + control. Turning of f speed control There are two ways to turn off the speed control: • Depress the brake pedal. This will not erase your vehicle’ s previously set speed.
In any mode: • Press VOL + or - to adjust the volume. Climate control features • Press TEMP + or - to adjust temperature. MOON ROOF (IF EQUIPPED) T o open the moon roof: • Press and hold the control forward to raise the moon roof to the vent position (when the glass panel is closed).
Do not let children play with the moon roof or leave children unattended in the vehicle. They may seriously hurt themselves. When closing the moon roof, you should verify that it is free of obstructions and ensure that children and/or pets are not in the proximity of the moon roof opening.
1. Press and hold the two outside buttons releasing only when the indicator light begins to flash after 20 seconds. Do not repeat Step 1 to program additional hand-held transmitters to the remaining two HomeLink 威 buttons. This will erase previously programmed hand-held transmitter signals into HomeLink 威 .
7. Press and release the “learn” or “smart” button. (The name and color of the button may vary by manufacturer .) Note: There are 30 seconds in which to initiate Step 8. 8. Return to the vehicle and firmly press, hold for two seconds and release the HomeLink 威 button.
Operating the HomeLink 姞 Wireless Control System T o operate, simply press and release the appropriate HomeLink 威 button. Activation will now occur for the trained product (garage door , gate operator , security system, entry door lock, or home or office lighting etc.
ELECTRONIC MESSAGE CENTER (IF EQUIPPED) The electronic message center only works when the ignition is in the ON position. The message center allows you to: • see problems such as door ajar , air sus.
E/M Press this control to switch the electronic instrument cluster display and the message center display from metric to English units. Select Each press of the SELECT control will select a different function. • Press the right side of the control to advance the function to the right.
Message center functions DIST ANCE TO EMPTY (DTE) This function estimates approximately how far you can drive with the fuel remaining in your tank under normal driving conditions. Remember to turn the ignition OFF when refueling to allow this feature to correctly detect the added fuel.
• variations in top-off procedure from one fill-up to another • rounding of the displayed values to the nearest 0.1 gallons (liter) Press the RESET control while A VG ECON is displayed to reset the function. The average displayed is the average since the last reset.
INTERIOR TRUNK CONTROL The remote trunk release control is located on the driver’ s door trim panel and can be operated at any time. Y ou can render the switch inoperable by locking the button with your master key .
POSITIVE RETENTION FLOOR MA T Position the driver floor mat so that the eyelet is over the pointed end of the retention post and rotate forward to lock in. Make sure that the mat does not interfere with the operation of the accelerator or the brake pedal.
KEYS The vehicle is equipped with a master (black) key and valet (gray) key lock system. The master key will access doors, trunk, glove box, ignition and remote trunk release.
Childproof door locks When these locks are set, the rear doors cannot be opened from the inside. The rear doors can be opened from the outside when the doors are unlocked. The childproof locks are located on rear edge of each rear door and must be set separately for each door .
Keep vehicle doors and luggage compartment locked and keep keys and remote transmitters out of a child’ s reach. Unsupervised children could lock themselves in the trunk and risk injury . Children should be taught not to play in vehicles. On hot days, the temperature in the trunk or vehicle interior can rise very quickly .
The remote entry system allows you to lock or unlock all vehicle doors without a key . The remote entry features operate with the ignition in any position, except in the 3 (ON) , with the transmission not in either P (Park) or N (Neutral).
3. Cycle the ignition from the 4 (ON) to the 3 (OFF) position. 4. Press the power door unlock control three times. 5. T urn the ignition to the 4 (ON) position. The doors will lock and unlock. 6. W ith the ignition still in the 4 (ON) position, press the unlock control twice.
T o replace the battery: 1. T wist a thin coin between the two halves of the remote entry transmitter near the key ring. DO NOT T AKE THE RUBBER COVER AND CIRCUIT BOARD OFF THE FRONT HOUSING OF THE REMOTE ENTRY TRANSMITTER. 2. Do not wipe off any grease on the battery terminals on the back surface of the circuit board.
• Perform the following programming procedure yourself: Place the key in the ignition and cycle from 1 (OFF/LOCK) to 3 (ON) eight times in rapid succession within 10 seconds. After doors lock/unlock, press any control on all transmitters (up to four).
Autolock (if equipped) This feature automatically locks all vehicle doors when: • all doors are closed, • the ignition is in the 3 (ON) position, • the brake pedal is depressed, • you shift into any gear .
KEYLESS ENTRY SYSTEM (IF EQUIPPED) W ith the keyless entry keypad, you can: • lock or unlock the vehicle doors without using the key . • open the trunk. See also Remote entry system in this chapter for more information. Y our vehicle has a factory-set 5–digit code that operates the keyless entry system.
3. Enter a second personal 5-digit code. Each number must be entered within five seconds of each other . 4. Press 3 • 4 to store the second personal code. 5. The doors will again lock then unlock to confirm programming of the new code. T o store a third personal code: 1.
• To release the trunk, enter the factory-set code or personal code (driver door unlocks) and press 5 • 6 within five seconds. After the factory-set code or personal code has been entered, you can unlock all doors (press 3 • 4) and release the trunk (press 5 • 6) as long as the controls are pressed within 5 seconds of each other .
• When the ignition is in the 3 (ON) position, the indicator will glow for 3 seconds to indicate normal system functionality . If a problem occurs with the SecuriLock 娂 system, the indicator will flash rapidly or glow steadily when the ignition is in the 3 (ON) position.
will need two previously programmed coded keys (keys that already operate your vehicle’ s engine) and the new unprogrammed key(s) readily accessible for timely implementation of each step in the procedure.
SEA TING Adjustable head restraints Y our vehicle’ s seats are equipped with head restraints which are vertically adjustable. The purpose of these head restraints is to help limit head motion in the event of a rear collision.
Lift handle to move seat forward or backward. Pull lever up to adjust seatback. Using the manual recline function (if equipped) Never adjust the driver’ s seat or seatback when the vehicle is moving. Do not pile cargo higher than the seatbacks to avoid injuring people in a collision or sudden stop.
T o adjust the front seatback using the manual recliner: • Lift and hold the handle located on the side of the seat. • Lean against the seatback to adjust it to your desired position. Y ou can recline the seat back or bring it forward. • Release the handle when the desired position has been reached.
Adjusting the power front seats – door mounted controls (if equipped) The controls for the power seats are located on the inside of each front door . Never adjust the driver’ s seat or seatback when the vehicle is moving. Do not pile cargo higher than the seatbacks to avoid injuring people in a collision or sudden stop.
Press to move the seat forward or backward. Press to move the front portion of the seat cushion up or down. Press to move the rear portion of the seat cushion up or down.
Seat mounted cup holders and armrest storage compartment (if equipped) Y our vehicle is equipped with cup holders in the rear seat armrest. T o access the cup holders, rotate armrest into use position. Use only soft cups in the cupholder . Hard objects can injure you in a collision.
How does the Personal Safety System 姟 work? The Personal Safety System 娂 can adapt the deployment strategy of your vehicle’ s safety devices according to crash severity and occupant conditions. A collection of crash and occupant sensors provides information to the Restraints control module (RCM).
in rear -facing child seats, this occurs because they are initially sitting very close to the airbag. For other occupants, this occurs when the occupant is not properly restrained by seat belts or child safety seats and they move forward during pre-crash braking.
of the safety belts and helps properly position the occupant relative to the airbag to improve protection. The safety belt pretensioners can be either activated alone or , if the collision is of sufficient severity , together with the airbags.
T o reduce the risk of injury , make sure children sit in the back seat where they can be properly restrained. Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision.
Combination lap and shoulder belts 1. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) until you hear a snap and feel it latch. Make sure the tongue is securely fastened in the buckle. 2. T o unfasten, push the release button and remove the tongue from the buckle.
Webbing extraction sensitive mode The webbing sensitive locking mode locks the webbing and prevents more belt from being pulled out if the belt is pulled out too quickly . The belt will unlock when you stop pulling on it. Automatic locking mode In this mode, the shoulder belt is pre-locked.
• Grasp the shoulder portion and pull downward until the entire belt is pulled out. • Allow the belt to retract. As the belt retracts, you will hear a clicking sound.
Position the safety belt height adjusters so that the belt rests across the middle of your shoulder . Failure to adjust the safety belt properly could reduce the effectiveness of the seat belt and increase the risk of injury in a collision.
Conditions of operation If... Then... The driver’ s safety belt is not buckled before the ignition switch is turned to the ON position... The safety belt warning light illuminates 1-2 minutes and the warning chime sounds 4-8 seconds. The driver’ s safety belt is buckled while the indicator light is illuminated and the warning chime is sounding.
If... Then... The driver’ s and front passenger’ s safety belts are buckled before the ignition switch is turned to the ON position or less than 1-2 minutes have elapsed since the ignition switch has been turned ON... The BeltMinder 娂 feature will not activate.
The following are reasons most often given for not wearing safety belts (All statistics based on U.S. data): Reasons given... Consider ... “Crashes are rare events” 36700 crashes occur every day . The more we drive, the more we are exposed to “rare” events, even for good drivers.
Reasons given... Consider ... “I have an airbag” Airbags offer greater protection when used with safety belts. Frontal airbags are not designed to inflate in rear and side crashes or rollovers. “I’d rather be thrown clear” Not a good idea. People who are ejected are 40 times more likely to DIE.
• The gearshift is in P (Park) (automatic transmission) • The ignition switch is in the OFF position • The driver and front passenger safety belts are unbuckled T o reduce the risk of injury , do not deactivate/activate the BeltMinder 娂 feature while driving the vehicle.
Do not use extensions to change the fit of the shoulder belt across the torso. Safety belt maintenance Inspect the safety belt systems periodically to make sure they work properly and are not damaged. Inspect the safety belts to make sure there are no nicks, tears or cuts.
Important SRS precautions The SRS is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries.
Do not attempt to service, repair , or modify the steering column, its adaptive module, or its fuses. See your Ford or Lincoln/Mercury dealer . T o properly position yourself away from the airbag: • Move your seat to the rear as far as you can while still reaching the pedals comfortably .
Children and airbags Children must always be properly restrained. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position. Failure to follow these instructions may increase the risk of injury in a collision.
The airbags inflate and deflate rapidly upon activation. After airbag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder (to lubricate the bag) or sodium compounds (e.
Several air bag system components get hot after inflation. Do not touch them after inflation. If the air bag has deployed, the air bag will not function again and must be replaced immediately . If the air bag is not replaced, the unrepaired area will increase the risk of injury in a collision.
Even with the front passenger sensing system, children 12 and under should be properly restrained in the back seat. When the front passenger seat is occupied and the sensing system has turned off the .
injury in a crash event. For example, if an occupant slouches, lies down, turns sideways, sits forward, leans forward or sideways, or puts one or both feet up, the chance of injury during a crash is greatly increased.
Any alteration/modification to the front passenger seat may affect the performance of the front passenger sensing system. Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a tone to indicate the condition of the system.
Do not attempt to service, repair , or modify the airbag SRS, its fuses or the seat cover on a seat containing an airbag. See your Ford or Lincoln Mercury dealer . All occupants of the vehicle should always wear their safety belts even when an airbag SRS is provided.
The fact that the airbags did not inflate in a collision does not mean that something is wrong with the system. Rather , it means the forces were not of the type sufficient to cause activation.
Disposal of airbags and airbag equipped vehicles (including pretensioners) See your local dealership or qualified technician. Airbags MUST BE disposed of by qualified personnel. SAFETY RESTRAINTS FOR CHILDREN See the following sections for directions on how to properly use safety restraints for children.
Do not leave children, unreliable adults, or pets unattended in your vehicle. Child booster seats Children outgrow a typical convertible or toddler seat when they weigh 40 lb.
T ypes of booster seats There are two types of belt-positioning booster seats: • Those that are backless. If your backless booster seat has a removable shield, remove the shield and use the lap/shoulder belt.
Follow all instructions provided by the manufacturer of the booster seat. Never put the shoulder belt under a child’ s arm or behind the back because it eliminates the protection for the upper part of the body and may increase the risk of injury or death in a collision.
• LA TCH lower anchors are recommended for use by children up to 48 lb. (22 kg) in a child restraint. T op tether anchors can be used for children up to 60 lb. (27 kg) in a child restraint, and to provide upper torso restraint for children up to 80 lb.
1. Position the child safety seat in a seat with a combination lap and shoulder belt. 2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together . 3. While holding the shoulder and lap belt portions together , route the tongue through the child seat according to the child seat manufacturer’ s instructions.
4. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) for that seating position until you hear a snap and feel the latch engage.
8. Allow the safety belt to retract to remove any slack in the belt. 9. Before placing the child in the seat, forcibly move the seat forward and back to make sure the seat is securely held in place. T o check this, grab the seat at the belt path and attempt to move it side to side and forward.
1. Position the child safety seat on the seat cushion. 2. Route the child safety seat tether strap over the back of the seat. For vehicles with adjustable head restraints, route the tether strap under the head restraint and between the head restraint posts, otherwise route the tether strap over the top of the seatback.
Attaching safety seats with LA TCH (Lower Anchors and T ethers for Children) attachments Some child safety seats have two rigid or webbing mounted attachments that connect to two anchors at certain seating positions in your vehicle. This type of child seat eliminates the need to use seat belts to attach the child seat.
If you install a child seat with rigid LA TCH attachments, do not tighten the tether strap enough to lift the child seat off the vehicle seat cushion when the child is seated in it. Keep the tether strap just snug without lifting the front of the child seat.
INFORMA TION ABOUT UNIFORM TIRE QUALITY GRADING New vehicles are fitted with tires that have a rating on them called T ire Quality Grades. The Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width.
The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics.
• Extra load: A class of P-metric or Metric tires designed to carry a heavier maximum load at 41 psi [43 psi (2.9 bar) for Metric tires]. Increasing the inflation pressure beyond this pressure will not increase the tire’ s load carrying capability .
tread grooves. Check for holes or cuts that may permit air leakage from the tire and make necessary repairs. Also inspect the tire sidewalls for cuts, bruises and other damage. If internal damage to the tire is suspected, have the tire demounted and inspected in case it needs to be repaired or replaced.
inflation pressure should never be set lower than the recommended pressure on the Safety Compliance Certification Label. When weather temperature changes occur , tire inflation pressures also change. A 10° F (6° C) temperature drop can cause a corresponding drop of 1 psi (7 kPa) in inflation pressure.
Only use replacement tires and wheels that are the same size and type (such as P-metric versus L T -metric or all-season versus all-terrain) as those originally provided by Ford.
When driving with the T -type/mini-spare tire do not: • Exceed 50 mph (80 km/h) • Load the vehicle beyond maximum vehicle load rating listed on the Safety Compliance Label • T ow a trailer • U.
• Use snow chains on the end of the vehicle with the dissimilar spare tire/wheel The usage of a dissimilar spare tire/wheel can lead to impairment of the following: • Handling, stability and braki.
1. Park on a level surface, activate hazard flashers and set parking brake. 2. Place gearshift lever in P (Park), turn engine OFF and block the diagonally opposite wheel.
4. Remove the lug wrench from the jack. Rotate the lug wrench socket out from the handle. 5. Locate pry off notch (if equipped) and remove the center ornament from the aluminum wheel with the tapered end of the wheel nut wrench that came with your vehicle.
• Position the jack according to the following guides and turn the jack handle clockwise until the wheel is completely off the ground. T o lessen risk of personal injury , do not put any part of your body under the vehicle while changing a tire. Do not start the engine when your vehicle is on the jack.
12. For full size spare aluminum wheel, firmly install the center ornament. If equipped with a full size spare tire/wheel assembly and lug nut retained full wheelcover , install the wheelcover by tightening the five black plastic nuts in the order shown on the wheelcover using the lug wrench with about 6.
Information on “P” type tires P215/65R15 95H is an example of a tire size, load index and speed rating. The definitions of these items are listed below . (Note that the tire size, load index and speed rating for your vehicle may be different from this example.
Note: Y ou may not find this information on all tires because it is not required by federal law . Letter rating Speed rating - mph (km/h) M 81 mph (130 km/h) N 87 mph (140 km/h) Q 99 mph (159 km/h) R .
12. T readwear , T raction and T emperature Grades • T readwear: The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course.
Additional information contained on the tire sidewall for “L T” type tires “L T” type tires have some additional information beyond those of “P” type tires; these differences are described below: 1. LT: Indicates a tire, designated by the T ire and Rim Association (T&RA), that is intended for service on light trucks.
Information on “T” type tires “T” type tires have some additional information beyond those of “P” type tires; these differences are described below: T145/80D16 is an example of a tire size. Note: The temporary tire size for your vehicle may be different from this example.
TIRE CARE Improper or inadequate vehicle maintenance can also cause tires to wear abnormally . Here are some of the important maintenance items: Tire wear Measure and inspect the tire tread on all your tires periodically . Advanced and unusual tire wear can reduce the ability of tread to grip the road in adverse (wet, snowy , etc.
Safety practices Driving habits have a great deal to do with your tire mileage and safety . • Observe posted speed limits • A void fast starts, stops and turns • A void potholes and objects on the road • Do not run over curbs or hit the tire against a curb when parking If your vehicle is stuck in snow , mud, sand, etc.
The tires should also be balanced periodically . An unbalanced tire and wheel assembly may result in irregular tire wear . Tire rotation Rotating your tires at the recommended interval (as indicated i.
• Rear Wheel Drive (RWD) vehicles/Four Wheel Drive (4WD)/ All Wheel Drive (A WD) vehicles (front tires at top of diagram) Sometimes irregular tire wear can be corrected by rotating the tires.
Follow these guidelines when using snow tires and chains: • Either cable type chains or SAE class S chains can be used. • Install chains securely , verifying that the chains do not touch any wiring, brake lines or fuel lines. • Drive cautiously .
Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be found on the Safety Compliance Certification Label on the B-Pillar or the edge of the driver’ s door . Look for “THE COMBINED WEIGHT OF OCCUP ANTS AND CARGO SHOULD NEVER EXCEED XXX kg OR XXX lb.
Example only: Cargo W eight – includes all weight added to the Base Curb W eight, including cargo and optional equipment. When towing, trailer tongue load or king pin weight is also part of cargo weight.
GA W (Gross Axle W eight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload. GA WR (Gross Axle W eight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear).
GVWR (Gross V ehicle W eight Rating) – is the maximum allowable weight of the fully loaded vehicle (including all options, equipment, passengers and cargo). The GVWR is shown on the Safety Compliance Certification Label located on the B-Pillar or the edge of the driver’ s door .
mandatory options, no cargo (internal or external), a tongue load of 10–15% (conventional trailer) or king pin weight of 15–25% (fifth wheel trailer), and driver only (150 lb. [68 kg]). Consult your dealership (or the RV and T railer T owing Guide provided by your dealership) for more detailed information.
capacity to carry you, 4 of your friends and all the golf bags? Y ou and four friends average 220 lb. (99 kg) each and the golf bags weigh approximately 30 lb. (13.5 kg) each. The calculation would be: 1400 – (5 x 220) – (5 x 30) = 1400 – 1100 – 150 = 150 lb.
T owing trailers beyond the maximum recommended gross trailer weight exceeds the limit of the vehicle and could result in engine damage, transmission damage, structural damage, loss of vehicle control, vehicle rollover and personal injury . The GCW of your vehicle and trailer should not exceed 6,600 lb.
T railer lamps T railer lamps are required on most towed vehicles. Make sure all running lights, brake lights, turn signals and hazard lights are working. See your dealer or trailer rental agency for proper instructions and equipment for hooking up trailer lamps.
Launching or retrieving a boat Disconnect the wiring to the trailer before backing the trailer into the water . Reconnect the wiring to the trailer after the trailer is removed from the water . When backing down a ramp during boat launching or retrieval: • do not allow the static water level to rise above the bottom edge of the rear bumper .
STARTING Positions of the ignition 1. OFF/LOCK, shuts off the engine and all accessories/locks the gearshift lever and allows key removal. 2. ACC, allows the electrical accessories such as the radio to operate while the engine is not running. 3. ON, all electrical circuits operational.
If you smell exhaust fumes inside your vehicle, have your dealer inspect your vehicle immediately . Do not drive if you smell exhaust fumes. Important safety precautions A computer system controls the engine’ s idle revolutions per minute (RPM). When the engine starts, the idle RPM runs higher than normal in order to warm the engine.
5. T urn the key to 3 (ON) without turning the key to 4 (ST ART). Make sure the corresponding lights illuminate or illuminate briefly . If a light fails to illuminate, have the vehicle serviced. • If the driver’ s safety belt is fastened, the light may not illuminate.
Starting the engine 1. T urn the key to 3 (ON) without turning the key to 4 (ST ART). 2. T urn the key to 4 (ST ART), then release the key as soon as the engine starts. Excessive cranking could damage the starter . Note: If the engine does not start within five seconds on the first try , turn the key to OFF , wait 10 seconds and try again.
BRAKES Y our service brakes are self-adjusting. Refer to the scheduled maintenance information for scheduled maintenance. Occasional brake noise is normal and often does not indicate a performance concern with the vehicle’ s brake system.
The ABS operates by detecting the onset of wheel lockup during brake applications and compensates for this tendency . The wheels are prevented from locking even when the brakes are firmly applied.
Parking brake with auto-release (if equipped) Apply the parking brake whenever the vehicle is parked. T o set the parking brake: 1. Move the gearshift to P (Park). 2. Push pedal downward. The BRAKE warning lamp in the instrument cluster illuminates and remains illuminated (when the ignition is turned ON) until the parking brake is fully released.
If the parking brake fails to release after completing this procedure, use the manual parking brake release lever . Pull the lever to manually release the parking brake. T RACTION CONTROL 姟 (IF EQUIPPED) Y our vehicle may be equipped with the optional T raction Control 娂 system.
During T raction Control 娂 operation you may hear an electric motor type of sound coming from the engine compartment and the engine will not “rev-up” when you push further on the accelerator .
It is also important to maintain a proper power steering fluid level in the power steering fluid reservoir: • Do not operate the vehicle with a low power steering pump fluid level (below the MIN mark on the reservoir). • Some noise is normal during operation.
This system keeps the rear of your vehicle at a constant level by automatically adding air or releasing air from the springs. If you exceed the load limit, the rear air suspension may not operate. The air suspension shut-off switch is located on the left side of the trunk.
2. Locate the access plug on the underside of the steering column cover . 3. Remove the access plug using a flat head screwdriver . Insert the screwdriver into the access hole nearest the steering wheel. Then push and hold the override button using a flat head screwdriver .
2. Insert the key and turn it to ACC. Apply the brake pedal and shift to N (Neutral) . When the key is in the ignition and in the ACC position, the automatic transmission shift lever can be moved from the P (Park) position without the brake pedal depressed.
• Depress the brake pedal • Move the gearshift lever into the desired gear T o put your vehicle in P (Park): • Come to a complete stop • Move the gearshift lever and securely latch it in P (Park) Always set the parking brake fully and make sure the gearshift is latched in P (Park).
If your vehicle is equipped with a floor -shift transmission, overdrive can be deactivated by pressing the transmission control switch on the gearshift handle. The transmission control indicator light (TCIL) will illuminate on the instrument cluster .
2 (Second) This position allows for second gear only . • Provides engine braking. • Use to start-up on slippery roads. • T o return to (Overdrive), move the gearshift lever into the (Overdrive) position. • Selecting 2 (Second) at higher speeds will cause the transmission to downshift to second gear at the appropriate vehicle speed.
DRIVING THROUGH WATER Do not drive quickly through standing water , especially if the depth is unknown. T raction or brake capability may be limited and if the ignition system gets wet, your engine may stall. W ater may also enter your engine’ s air intake and severely damage your engine.
GETTING ROADSIDE ASSISTANCE T o fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program.
Canadian customers who require roadside assistance, call 1–800–665–2006. If you need to arrange roadside assistance for yourself, Ford Motor Company will reimburse a reasonable amount. T o obtain reimbursement information, U.S. Ford or Mercury vehicles customers call 1-800-241-3673; Lincoln vehicle customers call 1–800–521–4140.
The fuel pump shut-off switch is located on the left side of the trunk behind the left rear tail light and the trunk liner . Use the following procedure to reset the fuel pump shut-off switch. 1. T urn the ignition to the OFF position. 2. Check the fuel system for leaks.
Note: Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire.
The fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 1 15A T axi, Cluster , Lighting Control Module (Interior Lighting) 2 10A Ignition (ON) .
Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 6 10A Ignition (ON) - Cluster 7 10A LCM (Park lamps, Switch illumination) 8 10A Ignition (ON) - Rear Air Suspension Mod.
Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 19 10A Left-hand low beam, DRL 20 10A Ignition (ON/ACC) - Back-up lamps 21 10A Right-hand low beam, DRL 22 10A Ignition.
Power distribution box The power distribution box is located in the engine compartment. The power distribution box contains high-current fuses that protect your vehicle’ s main electrical systems from overloads. Always disconnect the battery before servicing high current fuses.
Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 1 20A* Ignition switch (Key in, RUN 1, RUN 2) 2 25A* Ignition switch (RUN/ST ART , RUN/ACC, ST ART) 3 10A* Powertrain Control Mod.
Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 102 50A** Cooling fan 103 50A** Instrument panel (I/P) fuse box feed #1, I/P fuses 23, 25, 27 and 31 104 40A** Instrument panel (.
Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 118 50A** Rear power point or Police trunk accessory battery feed (Police vehicles only) 201 1 ⁄ 2 ISO relay A/C clutch 202 —.
Relays Relays are located in the power distribution box and should be replaced by qualified technicians. JUMP STARTING YOUR VEHICLE The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or vehicle damage.
Connecting the jumper cables 1. Connect the positive (+) jumper cable to the positive (+) terminal of the discharged battery . Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery . 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery .
3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery . 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’ s engine, away from the battery and the carburetor/fuel injection system.
3. Once the disabled vehicle has been started, run both engines for an additional three minutes before disconnecting the jumper cables. Removing the jumper cables Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the ground metal surface.
3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’ s battery . 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’ s battery .
WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or , if you are a member of a roadside assistance program, your roadside assistance service provider . It is recommended that your vehicle be towed with a wheel lift or flatbed equipment.
GETTING THE SERVICES YOU NEED At home Y ou must take your Ford vehicle to an authorized Ford dealer for warranty repairs. While any Ford dealership handling your vehicle line will provide warranty service, we recommend you return to your selling dealer who wants to ensure your continued satisfaction.
In Canada: Customer Relationship Centre Ford Motor Company of Canada, Limited P .O. Box 2000 Oakville, Ontario L6J 5E4 1-800-565-3673 (FORD) www .ford.
In some states (in the U.S.) you must directly notify Ford in writing before pursuing remedies under your state’ s warranty laws. Ford is also allowed a final repair attempt in some states.
THE DISPUTE SETTLEMENT BOARD (U.S. ONLY) The Dispute Settlement Board is: • an independent, third-party arbitration program for warranty disputes. • available free to owners and lessees of qualifying Ford Motor Company vehicles. The Dispute Settlement Board may not be available in all states.
Board membership The Board consists of: • Three consumer representatives • A Ford or Lincoln Mercury dealership representative Consumer candidates for Board membership are recruited and trained by an independent consulting firm.
Oral presentations If you would like to make an oral presentation, indicate YES to question 6 on the application. While it is your right to make an oral presentation before the Board, this is not a requirement and the Board will decide the case whether or not an oral presentation is made.
dealer to resolve a factory-related vehicle service concern have been unsatisfactory , Ford of Canada participates in an impartial third party mediation/arbitration program administered by the Canadian Motor V ehicle Arbitration Plan (CAMV AP).
information is subject to change, please ask your dealer for complete details about Ford Extended Service Plan coverage options, or visit the Ford ESP website at www .ford-esp.com. GETTING ASSIST ANCE OUTSIDE THE U.S. AND CANADA Before exporting your vehicle to a foreign country , contact the appropriate foreign embassy or consulate.
Or call: For a free publication catalog, order toll free: 1-800-782-4356 Monday-Friday 8:00 a.m. - 6:00 p.m. EST Helm, Incorporated can also be reached by their website: www .helminc.com. (Items in this catalog may be purchased by credit card, check or money order .
W ASHING THE EXTERIOR W ash your vehicle regularly with cool or lukewarm water and a neutral pH shampoo, such as Motorcraft Detail W ash (ZC-3–A), which is available from your dealer . • Never use strong household detergents or soap, such as dish washing or laundry liquid.
• Remove particles such as bird droppings, tree sap, insect deposits, tar spots, road salt and industrial fallout before repairing paint chips. • Always read the instructions before using the products. ALUMINUM WHEELS AND WHEEL COVERS Aluminum wheels and wheel covers are coated with a clearcoat paint finish.
• Cover the highlighted areas to prevent water damage when cleaning the engine. • Never wash or rinse the engine while it is running; water in the running engine may cause internal damage. PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts.
• Do not use abrasives, as they may cause scratches. • Do not use fuel, kerosene, or paint thinner to clean any parts. • W iper blades can be cleaned with isopropyl (rubbing) alcohol or windshield washer solution. Be sure to replace wiper blades when they appear worn or do not function properly .
• If a ring forms on the fabric after spot cleaning, clean the entire area immediately (but do not oversaturate) or the ring will set. • Do not use household cleaning products or glass cleaners, which can stain and discolor the fabric and affect the flame retardant abilities of the seat materials.
vehicle. Each product is made from high quality materials that meet or exceed rigid specifications. For best results, use the following products or products of equivalent quality: Motorcraft Bug and T.
SERVICE RECOMMENDATIONS T o help you service your vehicle: • W e highlight do-it-yourself items in the engine compartment for easy location. • W e provide scheduled maintenance information which makes tracking routine service easy . If your vehicle requires professional service, your dealership can provide the necessary parts and service.
OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the instrument panel. 2. Go to the front of the vehicle and release the auxiliary latch that is located under the front of the hood. 3. Lift the hood until the lift cylinders hold it open.
5. Power steering fluid reservoir 6. Engine coolant reservoir 7. Battery 8. Power distribution box 9. Engine oil filler cap 10. Automatic transmission fluid dipstick WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if the level is low . In very cold weather , do not fill the reservoir completely .
2. T urn the engine off and wait up to 10 minutes for the oil to drain into the oil pan. 3. Set the parking brake and ensure the gearshift is securely latched in P (Park). 4. Open the hood. Protect yourself from engine heat. 5. Locate and carefully remove the engine oil level indicator (dipstick).
• If required, add engine oil to the engine. Refer to Adding engine oil in this chapter . • Do not overfill the engine with oil. Oil levels above this mark may cause engine damage. If the engine is overfilled, some oil must be removed from the engine by a qualified service technician.
Engine oil and filter recommendations Look for this certification trademark. Use SAE 5W -20 engine oil. Only use oils “Certified For Gasoline Engines” by the American Petroleum Institute (API).
BATTERY Y our vehicle is equipped with a Motorcraft maintenance-free battery which normally does not require additional water during its life of service. However , for severe usage or in high temperature climates, check the battery electrolyte level. Refer to scheduled maintenance information for the service interval schedules.
When lifting a plastic-cased battery , excessive pressure on the end walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery . Lift the battery with a battery carrier or with your hands on opposite corners.
• Always dispose of automotive batteries in a responsible manner . Follow your local authorized standards for disposal. Call your local authorized recycling center to find out more about recycling automotive batteries.
When the engine is cold, check the level of the engine coolant in the reservoir . • The engine coolant should be at the “FULL COLD” level or within the “COLD FILL RANGE” as listed on the engine coolant reservoir (depending upon application).
Do not add engine coolant when the engine is hot. Steam and scalding liquids released from a hot cooling system can burn you badly . Also, you can be burned if you spill coolant on hot engine parts. Do not put engine coolant in the windshield washer fluid container .
coolant degas system with a pressurized cap, or if it is necessary to remove the coolant pressure relief cap on the radiator of a vehicle with an overflow system, follow these steps to add engine coolant. T o reduce the risk of personal injury , make sure the engine is cool before unscrewing the coolant pressure relief cap.
Used engine coolant should be disposed of in an appropriate manner . Follow your community’ s regulations and standards for recycling and disposing of automotive fluids. Coolant refill capacity T o find out how much fluid your vehicle’ s cooling system can hold, refer to Refill capacities in this section.
What you should know about fail-safe cooling If the engine coolant supply is depleted, this feature allows the vehicle to be driven temporarily before incremental component damage is incurred. The “fail-safe” distance depends on ambient temperatures, vehicle load and terrain.
• The engine power will be limited. • The air conditioning system will be disabled. Continued operation will increase the engine temperature: • The engine will completely shut down, causing steering and braking effort to increase. Once the engine temperature cools, the engine can be re-started.
If you do not use the proper fuel filler cap, excessive pressure or vacuum in the fuel tank may damage the fuel system or cause the fuel cap to disengage in a collision, which may result in possible personal injury . Automotive fuels can cause serious injury or death if misused or mishandled.
splashed on the skin, promptly wash skin thoroughly with soap and water . Consult a physician immediately if you experience an adverse reaction. When refueling always shut the engine off and never allow sparks or open flames near the filler neck. Never smoke while refueling.
When fueling your vehicle: 1. T urn the engine off. 2. Carefully turn the filler cap counterclockwise 1/4 of a turn until it stops. 3. Pull to remove the cap from the fuel filler pipe. 4. T o install the cap, align the tabs on the cap with the notches on the filler pipe.
Repairs to correct the effects of using a fuel for which your vehicle was not designed may not be covered by your warranty . Octane recommendations Y our vehicle is designed to use “Regular” unleaded gasoline with pump (R+M)/2 octane rating of 87.
If you have run out of fuel: • Y ou may need to cycle the ignition from OFF to ON several times after refueling, to allow the fuel system to pump the fuel from the tank to the engine. • Y our “Check Engine” indicator may come on. For more information on the “Check Engine” indicator , refer to the Instrument Cluster chapter .
For consistent results when filling the fuel tank: • T urn the engine/ignition switch to the off position prior to refueling, an error in the reading will result if the engine is left running. • Use the same filling rate setting (low — medium — high) each time the tank is filled.
Habits • Smooth, moderate operation can yield up to 10% savings in fuel. • Steady speeds without stopping will usually give the best fuel economy . • Idling for long periods of time (greater than one minute) may waste fuel. • Anticipate stopping; slowing down may eliminate the need to stop.
• Adding certain accessories to your vehicle (for example bug deflectors, rollbars/light bars, running boards, ski/luggage racks) may reduce fuel economy . • Using fuel blended with alcohol may lower fuel economy . • Fuel economy may decrease with lower temperatures during the first 8–10 miles (12–16 km) of driving.
emission control, such non-Ford parts should be equivalent to genuine Ford Motor Company parts in performance and durability . Do not park, idle, or drive your vehicle in dry grass or other dry ground cover . The emission system heats up the engine compartment and exhaust system, which can start a fire.
These temporary malfunctions can be corrected by filling the fuel tank with good quality fuel and/or properly tightening the fuel cap. After three driving cycles without these or any other temporary malfunctions present, the Check engine/Service engine soon light should turn off.
2. While the engine idles, turn the steering wheel left and right several times. 3. T urn the engine off. 4. Check the fluid level in the reservoir . It should be between the MIN and MAX lines.
weather or pulling a trailer , the vehicle should be turned off for about 30 minutes to allow fluid to cool before checking. 1. Drive the vehicle 20 miles (30 km) or until it reaches normal operating temperature. 2. Park the vehicle on a level surface and engage the parking brake.
The transmission fluid should be in this range if at normal operating temperature (150°F-170°F [66°C-77°C]). The transmission fluid should be in this range if at ambient temperature (50°F-95°F [10°C-35°C]). High fluid level Fluid levels above the safe range may result in transmission failure.
If an overfill occurs, excess fluid should be removed by a qualified technician. An overfill condition of transmission fluid may cause shift and/or engagement concerns and/or possible damage. Do not use supplemental transmission fluid additives, treatments or cleaning agents.
Note: Failure to use the correct air filter element may result in severe engine damage. The customer warranty may be voided for any damage to the engine if the correct air filter element is not used.
REFILL CAPACITIES Fluid Ford Part Name Capacity Engine oil (includes filter change) 6 Motorcraft SAE 5W -20 Premium Synthetic Blend Motor Oil (US) Motorcraft SAE 5W -20 Super Premium Motor Oil (Canada) 6.
5 Rear axles are considered lubricated for life when the vehicle is used for normal service. See your scheduled maintenance information for Severe Duty requirements.
Item Ford part name Ford part number Ford specification Hinges, latches, striker plates, fuel filler door hinge and seat tracks Multi-Purpose Grease XG-4 or XL-5 ESB-M1C93-B Lock cylinders Motorcraft .
ENGINE DATA Engine 4.6L V8 engine Cubic inches 281 Required fuel 87 octane Firing order 1-3-7-2-6-5-4-8 Ignition system Coil on plug Spark plug gap 0.052–0.056 inch (1.32–1.42mm) Compression ratio 9.4:1 V EHICLE DIMENSIONS (AT CURB MASS) V ehicle dimensions Inches (mm) (1) Overall length 213.
IDENTIFYING YOUR VEHICLE Certification label The National Highway T raffic Safety Administration Regulations require that a Safety Compliance Certification Label be affixed to a vehicle and prescribe where the Safety Compliance Certification Label may be located.
V ehicle identification number (VIN) The vehicle identification number is attached to a metal tag and is located on the driver side instrument panel. (Please note that in the graphic XXXX is representative of your vehicle identification number .) The V ehicle Identification Number (VIN) contains the following information: 1.
T ransmission/T ransaxle code designations Y ou can find a transmission/transaxle code on the Safety Compliance Certification Label . The following table tells you which transmission or transaxle each code represents.
GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for your vehicle through your local authorized Ford or Ford of Canada dealer .
Peace of mind First aid and safety kits Full vehicle covers Locking gas cap Remote start V ehicle security systems Mobile-Ease 娂 hands-free communication system For maximum vehicle performance, keep.
A ABS (see Brakes) ..................... 171 Air cleaner filter ............... 244–245 Air conditioning .......................... 40 Air suspension ...........................176 description .............................. 176 Airbag supplemental restraint system .
Climate control (see Air conditioning or Heating) ............40 Clock adjust 6-CD in dash ............................. 36 AM/FM ....................................... 21 AM/FM/Cassette ........................ 22 AM/FM/CD ..........................
recommendations ................... 221 refill capacities ........................ 246 specifications .................. 247, 249 Exhaust fumes .......................... 170 F Fail safe cooling ........................ 229 Floor mats ................
K Keyless entry system ................. 90 autolock ..................................... 89 keypad ....................................... 90 programming entry code ......... 90 Keys ....................................... 82, 93 positions of the ignition .
Rear window defroster ...............42 Relays ................................ 186, 195 Remote entry system ................. 84 illuminated entry ......................88 locking/unlocking doors ........... 85 opening the trunk .....................
T owing ....................................... 163 recreational towing ................. 166 trailer towing .......................... 163 wrecker .................................... 200 T raction control ........................ 174 T raction-lok rear axle .
261.
262.
263.
264.
Een belangrijk punt na aankoop van elk apparaat Ford 2005 Grand Marquis (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Ford 2005 Grand Marquis heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Ford 2005 Grand Marquis vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Ford 2005 Grand Marquis leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Ford 2005 Grand Marquis krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Ford 2005 Grand Marquis bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Ford 2005 Grand Marquis kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Ford 2005 Grand Marquis . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
