Gebruiksaanwijzing /service van het product 2006 E-150 van de fabrikant Ford
Ga naar pagina of 248
Introduction 4 Instrument Cluster 12 W arning and control lights 12 Gauges 16 Entertainment Systems 18 AM/FM stereo 18 AM/FM stereo with single CD 20 AM/FM stereo with in-dash six CD 24 Climate Contro.
Seating and Safety Restraints 58 Seating 58 Safety restraints 64 Airbags 74 Child restraints 83 Tires, Wheels and Loading 99 T ire Information 101 T ire Inflation 103 V ehicle loading 116 T railer tow.
Cleaning 191 Underbody preservation 195 Maintenance and Specifications 197 Engine compartment 199 Engine oil 200 Battery 203 Engine Coolant 206 Fuel information 212 Air filter(s) 228 Part numbers 228 Refill capacities 230 Lubricant specifications 234 Accessories 241 Index 243 All rights reserved.
CALIFORNIA Proposition 65 W arning W ARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
SAFETY AND ENVIRONMENT PROTECTION W arning symbols in this guide How can you reduce the risk of personal injury to yourself or others? In this guide, answers to such questions are contained in comments highlighted by the warning triangle symbol. These comments should be read and observed.
SPECIAL NOTICES Emission warranty The New V ehicle Limited W arranty includes Bumper -to-Bumper Coverage, Safety Restraint Coverage, Corrosion Coverage, and 6.0L Power Stroke Diesel Engine Coverage. In addition, your vehicle is eligible for Emissions Defect and Emissions Performance W arranties.
Special instructions For your added safety , your vehicle is fitted with sophisticated electronic controls. Please read the section Supplemental restraint system (SRS) in the Seating and Safety Restraints chapter . Failure to follow the specific warnings and instructions could result in personal injury .
If your vehicle is equipped with the Ford Ambulance Preparation Package, it will be indicated on the Safety Compliance Certification Label. The label is located on the driver’ s side door pillar or on the rear edge of the driver’ s door .
Middle East/North Africa vehicle specific information For your particular global region, your vehicle may be equipped with features and options that are different from the ones that are described in this Owner’ s Guide; therefore, a supplement has been supplied that complements this book.
These are some of the symbols you may see on your vehicle. V ehicle Symbol Glossary Safety Alert See Owner’ s Guide Fasten Safety Belt Air Bag-Front Air Bag-Side Child Seat Child Seat Installation W.
V ehicle Symbol Glossary Power W indows Front/Rear Power W indow Lockout Child Safety Door Lock/Unlock Interior Luggage Compartment Release Symbol Panic Alarm Engine Oil Engine Coolant Engine Coolant .
W ARNING LIGHTS AND CHIMES W arning lights and gauges can alert you to a vehicle condition that may become serious enough to cause expensive repairs. A warning light may illuminate when a problem exists with one of your vehicle’ s functions. Many lights will illuminate when you start your vehicle to make sure the bulb works.
Electronic throttle control (if equipped): Illuminates when the engine has defaulted to a ’limp-home’ operation. Report the fault to a dealer at the earliest opportunity . Check fuel cap: Illuminates when the fuel cap may not be properly installed.
Air bag readiness: If this light fails to illuminate when ignition is turned to ON, continues to flash or remains on, have the system serviced immediately . A chime will also sound when a malfunction in the supplemental restraint system has been detected.
Check gauge: Illuminates when any of the following conditions has occurred: • The engine coolant temperature is high. • The engine oil pressure is low . • Flashes when Failsafe cooling mode has been activated. T urn signal: Illuminates when the left or right turn signal or the hazard lights are turned on.
GAUGES Speedometer: Indicates the current vehicle speed. Engine coolant temperature gauge: Indicates engine coolant temperature. At normal operating temperature, the needle will be in the normal range (between “H” and “C”). If it enters the red section, the engine is overheating.
T rip odometer: Registers the miles (kilometers) of individual journeys. Press the SELECT/RESET control once to switch from the odometer to the trip odometer . Press the control again to select T rip A and T rip B features. T o reset the trip, press and hold the control again until the trip reading is 0.
AUDIO SYSTEMS AM/FM stereo (if equipped) 1. Seek: Press / to find the next listenable station down/up the frequency band. 2. T une: Press / to manually adjust the radio frequency down/up.
5. Power/volume: Press to turn ON/OFF; turn to increase or decrease volume levels. 6. T one: Press TONE until the desired level — Bass, T reble, Fade appears on the display . T urn the volume control to raise/lower the levels, or to move the audio sound from the right to left or the front to back (if equipped).
Satellite Compatible AM/FM Stereo In-Dash Single CD/MP3 Radio (if equipped) 1. SEEK: Press and release SEEK / for previous/next strong station or track. 2. TEXT : The filename (Fi), song title (So), artist text (Ar) or album text (AL) may be viewed while playing an MP3 selection.
3. AUX: This function is not operational. 4. MUTE: Press to MUTE playing media; press again to return to playing media. 5. EJ: Press to eject a CD. 6. Bass: Press BASS; then press SEL / to decrease/increase the bass output. T reble: Press TREB; then press SEL / to decrease/increase the treble output.
Folder/T rack mode: In MP3 mode, press MENU until MODE appears in the display . Use SEL to toggle between FOLDER (only tracks within selected folder are accessible) or TRACK (all tracks on disc are accessible) MODE. 10. REPEA T : Repeats the current CD/MP3 track when active (ON).
19. Power/volume: Press to turn ON/OFF; turn to increase or decrease volume levels. 20. CD: Press to enter CD mode. CD units are designed to play commercially pressed 4.
Premium Satellite Compatible AM/FM Stereo In-Dash Six CD/MP3 Radio (if equipped) 1. SEEK: Press and release SEEK / for previous/next strong station or track. 2. TEXT : The filename (Fi), song title (So), artist text (Ar) or album text (AL) may be viewed while playing an MP3 selection.
3. AUX: Press to toggle between the current playing media and DVD (if equipped). 4. MUTE: Press to MUTE playing media; press again to return to playing media 5. EJ: Press to eject a CD. Press EJ and a memory preset to eject a specific disc. Press and hold to eject all loaded discs.
AM/FM1/FM2. When the six strongest stations are filled, the station stored in preset 1 will begin playing. If there are less than six strong stations, the system will store the last one in the remaining presets. Setting the clock: Press MENU until SELECT HOUR or SELECT MINUTE is displayed.
18. Memory presets: T o set a station: Select frequency , tune to a station, press and hold a preset button until sound returns. 19. Power/volume: Press to turn ON/OFF; turn to increase or decrease volume levels. 20. Load: Press to load a CD. Press LOAD and a memory preset to load to a specific disc slot.
For information regarding SIRIUS Satellite Radio, please call toll-free 888-539-SIRIUS (888-539-7474) or visit the SIRIUS website at www .siriusradio.com 24.
Don’t: • Expose discs to direct sunlight or heat sources for extended periods of time. • Insert more than one disc into each slot of the CD changer magazine. • Clean using a circular motion. CD units are designed to play commercially pressed 4.
HEATER ONLY SYSTEM (IF EQUIPPED) 1. Fan speed adjustment: Controls the volume of air circulated in the vehicle. 2. T emperature selection: Controls the temperature of the airflow in the vehicle. 3. Air flow selections: Controls the direction of the airflow in the vehicle.
MANUAL HEATING AND AIR CONDITIONING SYSTEM (IF EQUIPPED) 1. Fan speed adjustment: Controls the volume of air circulated in the vehicle. 2. T emperature selection: Controls the temperature of the airflow in the vehicle. 3. Air flow selections: Controls the direction of the airflow in the vehicle.
T o aid in side window defogging/demisting in cold weather: 1. Select MIX. 2. Set the temperature control to maintain comfort. 3. Set the fan speed to HI. Do not place objects on top of the instrument panel as these objects may become projectiles in a collision or sudden stop.
HEADLAMP CONTROL • The first position turns on the parking, tail, license plate and side marker lamps. • The outer position turns on the headlamps. Battery saver The battery saver can be set to turn off the courtesy lamps within 2 or 10 minutes if a door is left open and the key is not in the ignition.
Daytime running lamps (DRL) (if equipped) T urns the headlamps on with a reduced output. T o activate: • the ignition must be in the ON position, • the headlamp control is in the OFF or parking lamp position and • the parking brake must be disengaged.
P ANEL DIMMER CONTROL T o adjust the brightness of the instrument panel, rotate the dimmer control clockwise/counterclockwise when the headlamp control is in the parking lamp or low-beam position. T o turn on the interior lamps, rotate the dimmer control fully counterclockwise.
3. T urn on the low beam headlamps and open the hood. 4. Locate the high intensity area of the beam pattern and place the top edge of the intensity zone even with the horizontal reference line (4). If the top edge of the high intensity area is not even with the horizontal line, follow the next step to adjust it.
8. • Aerodynamic: Locate the horizontal adjuster (1) for each headlamp. T urn it clockwise or counterclockwise, to place the left edge of the high intensity area even with the vertical line corresponding to the headlamp under adjustment. • Sealed beam: Locate the horizontal adjuster (2) for each headlamp.
Third row courtesy/reading/cargo lamps The dome portion of the lamp, the center light, can be turned on when the headlamp control is rotated fully counterclockwise or when any door is opened. W ith the ignition key in the ACC or ON position, the rear dome lamp can be turned ON or OFF by sliding the control.
Function Number of bulbs T rade number Headlamps (sealed beam) 2 H5054 Headlamps (aerodynamic) 2 9007 Park lamp and turn signal (front) 2 4157K or 3157K Back-up lamps 2 3156K or 3156 License plate lam.
4. Remove the bulb retaining ring by rotating it counterclockwise, and slide the ring off the plastic base. 5. Pull the bulb straight out. Handle a halogen headlamp bulb carefully and keep out of children’ s reach. Grasp the bulb only by its plastic base and do not touch the glass.
3. Remove the four headlamp bulb retaining screws and the retaining ring. 4. Remove the headlamp. 5. Disconnect the electrical connector from the bulb and remove the bulb. T o install the new bulb, follow the removal procedures in reverse order . Replacing front parking lamp/turn signal bulbs 1.
Replacing license plate lamp bulbs 1. T urn the headlamp switch to OFF and then remove the two screws and the license plate lamp assembly from the rear door . 2. Remove bulb socket from lamp assembly by turning counterclockwise. 3. Pull the bulb out from socket and push in the new bulb.
MULTI-FUNCTION LEVER W indshield wiper: Rotate the end of the control away from you to increase the speed of the wipers; rotate towards you to decrease the speed of the wipers. W indshield washer: Push the end of the stalk: • briefly: causes a single swipe of the wipers without washer fluid.
T o prolong the life of the wiper blades, it is highly recommended to scrape off the ice on the windshield before turning on the wipers. The layer of ice has many sharp edges and can damage the micro edge of the wiper rubber element. TILT STEERING WHEEL T o adjust the steering wheel: 1.
Installing a garage door opener (if equipped) The storage compartment can be converted to accommodate a variety of aftermarket garage door openers: 1. Place VELCRO 威 hook onto side of aftermarket transmitter opposite of actuator control. 2. Place the transmitter into storage compartment, control down.
Compass The compass display is contained in the overhead console. The vehicle heading is displayed as one of N, NE, E, SE, S, SW , W and NW . The compass reading may be affected when you drive near large buildings, bridges, power lines and powerful broadcast antenna.
• Drive the vehicle slowly (less than 5 km/h [3 mph]) in circles until CAL indicator turns off in about 2–3 complete circles. • The compass is now calibrated. AUXILIARY POWER POINT (12VDC) Power outlets are designed for accessory plugs only . Do not insert any other object in the power outlet as this will damage the outlet and blow the fuse.
When closing the power windows, you should verify they are free of obstructions and ensure that children and/or pets are not in the proximity of the window openings. Press and hold the bottom part of the rocker switch to open the window . Press and hold the top part of the rocker switch to close the window .
Fold-away mirrors The mirrors can be manually folded forward or backwards for narrow spaces like driving through an automatic car wash or backing out of a garage with the trailer tow mirror . The telescoping feature (if equipped) allows the mirror to extend approximately 3.
Setting speed control The controls for using your speed control are located on the steering wheel for your convenience. 1. Press the ON control and release it. 2. Accelerate to the desired speed. 3. Press the SET ACCEL control and release it. 4. T ake your foot off the accelerator pedal.
Increasing speed while using speed control There are two ways to set a higher speed: • Press and hold the SET ACCEL control until you get to the desired speed, then release the control. Y ou can also use the SET ACCEL control to operate the T ap-Up function.
Turning of f speed control There are two ways to turn off the speed control: • Depress the brake pedal. This will not erase your vehicle’ s previously set speed. • Press the speed control OFF control. Note: When you turn off the speed control or the ignition, your speed control set speed memory is erased.
KEYS The key operates all locks on your vehicle. Y ou should always carry a second key with you in a safe place in case you require it in an emergency . Y our keys are coded to your vehicle; using a non-coded key will not permit your vehicle to start.
REMOTE ENTRY SYSTEM (IF EQUIPPED) This device complies with part 15 of the FCC rules and with RS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Locking the doors 1. Press and release to lock all the doors. 2. Press and release again within three seconds to confirm that all the doors are closed and locked. Note: The doors will lock again, and the horn will chirp once. Sounding a panic alarm Press to activate the alarm.
4. Insert the new battery . Refer to the diagram inside the remote entry transmitter for the correct orientation of the battery . Press the battery down to ensure that the battery is fully seated in the battery housing cavity . 5. Snap the two halves back together .
6. Repeat Steps 4 and 5 to program each additional remote entry transmitter (up to four transmitters). 7. T urn the ignition to the (3) OFF position after you have finished programming all of the remote entry transmitters. 8. The doors will lock, then unlock, to confirm that the programming mode has been exited.
SEATING Notes: Reclining the seatback can cause an occupant to slide under the seat’ s safety belt, resulting in severe personal injuries in the event of a collision. Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop.
Pull lever up to adjust seatback. Using the manual lumbar support The lumbar support control is located on the inboard side of the driver’ s seat. T urn the lumbar support control clockwise to increase firmness. T urn the lumbar support control counterclockwise to increase softness.
Press to raise or lower the rear portion of the seat cushion. Press the control to move the seat forward, backward, up or down. Quick release captains chair (7 passenger configuration second row only) T o remove the seat: 1.
Stow the tongue end of the detachable anchor . 2. Pull the seat latch handle, then pull the seat toward the right side of the vehicle to disengage four pins from the floor mount. 3. Remove the seat. T o install the seat: Check to see that the seat and seatback is latched securely in position.
REAR SEATS Accessing the 4th and 5th row seats (if equipped) T o make access to the 4th and 5th row seats easier , attach the 3rd and 4th row passenger side seat belts to the trim panel by using the snaps attached to the seat belt webbing and the trim panel.
2. Pull the LH/RH seat latch handles (located under the seat) rearward to release the latch hook ends from the front strikers. 3. Move the seat rearward and lift the seats rear hooks away from the rear strikers prior to lifting the front hooks out from the front strikers.
SAFETY RESTRAINTS Safety restraints precautions Always drive and ride with your seatback upright and the lap belt snug and low across the hips. T o reduce the risk of injury , make sure children sit in the back seat where they can be properly restrained.
Safety belts and seats can become hot in a vehicle that has been closed up in sunny weather; they could burn a small child. Check seat covers and buckles before you place a child anywhere near them.
Automatic locking mode When to use the automatic locking mode In this mode, the shoulder belt is automatically pre-locked. The belt will still retract to remove any slack in the shoulder belt. The automatic locking mode is not available on the driver safety belt.
How to disengage the automatic locking mode Disconnect the combination lap/shoulder belt and allow it to retract completely to disengage the automatic locking mode and activate the vehicle sensitive (emergency) locking mode.
Front safety belt height adjustment The driver and front seat outboard positions are equipped with a height adjuster . Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder . T o adjust the shoulder belt height, push the button and slide the height adjuster up or down.
Shorten and fasten the belt when not in use. Safety belt warning light and indicator chime The safety belt warning light illuminates in the instrument cluster and a chime sounds to remind the occupants to fasten their safety belts. Conditions of operation If.
If... Then... The driver’ s safety belt is not buckled approximately 5 seconds after the safety belt warning light has turned off... The BeltMinder 娂 feature is activated - the safety belt warning light illuminates and the warning chime sounds for 6 seconds every 30 seconds, repeating for approximately 5 minutes or until safety belt is buckled.
Reasons given... Consider ... “I was in a hurry” Prime time for an accident. BeltMinder 娂 reminds us to take a few seconds to buckle up. “Seat belts don’t work” Safety belts, when used properly , reduce risk of death to front seat occupants by 45% in cars, and by 60% in light trucks.
Deactivating/activating the BeltMinder 姟 feature Read Step s1-5t horoughly before proceeding with the deactivation/activation programming procedure. The BeltMinder 娂 feature can be deactivated/act.
light will flash 4 times per second for 3 seconds, followed by 3 seconds with the light off, then followed by the airbag warning light flashing 4 times per second for 3 seconds again. 5. After receiving confirmation, the deactivation/activation procedure is complete.
AIRBAG SUPPLEMENT AL RESTRAINT SYSTEM (SRS) Important SRS precautions The SRS is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries. Airbags DO NOT inflate slowly; there is a risk of injury from a deploying airbag.
The National Highway T raffic Safety Administration (NHTSA) recommends a minimum distance of at least 25 cm (10 inches) between an occupant’ s chest and the driver airbag module. Never place your arm over the air bag module as a deploying air bag can result in serious arm fractures or other injuries.
Children and airbags Children must always be properly restrained. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position. Failure to follow these instructions may increase the risk of injury in a collision.
The airbags inflate and deflate rapidly upon activation. After airbag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder or sodium compounds which may irritate the skin and eyes, but none of the residue is toxic.
Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a tone to indicate the condition of the system. Refer to Airbag readiness section in the Instrument Cluster chapter . Routine maintenance of the airbag is not required.
Passenger airbag ON/OFF switch (if equipped) Note : The passenger airbag ON/OFF switch is on vehicles with a gross vehicle weight rating (GVWR) greater than 8500. See V ehicle loading – with and without a trailer in the T ires, Wheels, and loading chapter .
In order to avoid inadvertent activation of the switch, always remove the ignition key from the passenger air bag ON/OFF switch. An infant in a rear -facing seat faces a high risk of serious or fatal injuries from a deploying passenger airbag.
If your vehicle has rear seats, always transport children who are 12 and younger in the rear seat. Always use safety belts and child restraints properly . If a child in a rear facing infant seat must be transported in front, the passenger airbag must be turned OFF .
• the child has a medical condition which, according to the child’ s physician, makes it necessary for the child to ride in the front seat so that the driver can constantly monitor the child’ s condition.
• the child has a medical condition that, according to the child’ s physician, makes it necessary for the child to ride in the front seat so that the driver can monitor the child’ s condition.
Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision. Always follow the instructions and warnings that come with any infant or child restraint you might use.
Do not leave children, unreliable adults, or pets unattended in your vehicle. Child booster seats Children outgrow a typical convertible or toddler seat when they weigh 40 lb.
T ypes of booster seats There are two types of belt-positioning booster seats: • Those that are backless. If your backless booster seat has a removable shield, remove the shield and use the lap/shoulder belt.
Follow all instructions provided by the manufacturer of the booster seat. Never put the shoulder belt under a child’ s arm or behind the back because it eliminates the protection for the upper part of the body and may increase the risk of injury or death in a collision.
• LA TCH lower anchors are recommended for use by children up to 48 pounds (22 kg) in a child restraint. T op tether anchors can be used for children up to 60 pounds (27 kg) in a child restraint, and to provide upper torso restraint for children up to 80 pounds (36 kg) using an upper torso harness and a belt-positioning booster .
2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together . 3. While holding the shoulder and lap belt portions together , route the tongue through the child seat according to the child seat manufacturer’ s instructions.
5. T o put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is extracted. 6. Allow the belt to retract. The belt will click as it retracts to indicate it is in the automatic locking mode.
Attaching safety seats with tether straps Children should be placed in the rear in an appropriate child safety seat that is properly secured to the vehicle.
1. Position the child safety seat on the front right-hand passenger seat. 2. Adjust the front right-hand passenger seat full forward. 3. Route the child safety seat tether strap over the back of the front right-hand passenger seat as shown. 4. Clip the tether strap hook to the seat pedestal to the location shown.
5. Adjust the front right hand passenger seat to the full rearward position. 6. Install the child safety seat tightly using the LA TCH anchors or safety belts. Follow the instructions in this chapter . 7. T ighten the child safety seat tether strap according to the manufacturer’ s instructions.
1. Position the child safety seat on the second row left hand or right hand bucket seat. 2. Route the child safety tether strap over the back of the left hand or right hand second row bucket seat. 3. Clip the tether strap hook to the seat pedestal at the location shown.
2. Route the child safety tether strap over the back of 3–Passenger bench seat. 3. Clip the tether strap hook to the tether bracket mounted under rear rail of seat cushion frame. 4. Install the child safety seat tightly using the LA TCH anchors or safety belts.
Y our vehicle may be equipped with LA TCH anchors for child seat installation at the seating positions marked with the child seat symbol: • Five passenger crew van • Seven passenger wagon • Eigh.
• Fifteen passenger wagon represents LA TCH anchors. represents tether strap anchors. Never attach two LA TCH child safety seats to the same anchor . In a crash, one anchor may not be strong enough to hold two child safety seat attachments and may break, causing serious injury or death.
Each time you use the safety seat, check that the seat is properly attached to the lower anchors and tether anchor . T ry to tilt the child seat from side to side.
NOTICE TO UTILITY VEHICLE AND TRUCK OWNERS Utility vehicles and trucks handle differently than passenger cars in the various driving conditions that are encountered on streets, highways and off-road.
VEHICLE CHARACTERISTICS How your vehicle differs from other vehicles SUV and trucks can differ from some other vehicles in a few noticeable ways. Y our vehicle may be: • Higher – to allow higher load carrying capacity and to allow it to travel over rough terrain without getting hung up or damaging underbody components.
INFORMA TION ABOUT UNIFORM TIRE QUALITY GRADING New vehicles are fitted with tires that have a rating on them called T ire Quality Grades. The Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width.
The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics.
• kPa: Kilopascal, a metric unit of air pressure. • PSI: Pounds per square inch, a standard unit of air pressure. • Cold inflation pressure: The tire pressure when the vehicle has been stationary and out of direct sunlight for an hour or more and prior to the vehicle being driven for 1 mile (1.
Also inspect the tire sidewalls for cuts, bruises and other damage. If internal damage to the tire is suspected, have the tire demounted and inspected in case it needs to be repaired or replaced. For your safety , tires that are damaged should not be used because they are more likely to blow out or fail.
When weather temperature changes occur , tire inflation pressures also change. A 10° F (6° C) temperature drop can cause a corresponding drop of 1 psi (7 kPa) in inflation pressure. Check your tire pressures frequently and adjust them to the proper pressure which can be found on the Safety Compliance Certification Label.
Tire inflation information All tires with Steel Carcass Plies (if equipped): This type of tire utilizes steel cords in the sidewalls. As such, they cannot be treated like normal light truck tires.
Stay out of the trajectory (1) as indicated in the illustration. TIRE REPLACEMENT REQUIREMENTS Y our vehicle is equipped with tires designed to provide a safe ride and handling capability .
Make sure all tires and wheels on the vehicle are of the same size, type, tread design, brand, load-carrying capacity and speed rating because it can affect the safety and performance of your vehicle, which could result in an increased risk of loss of vehicle control, vehicle rollover , personal injury and death.
4. R: Indicates a “radial” type tire. 5. 15: Indicates the wheel or rim diameter in inches. If you change your wheel size, you will have to purchase new tires to match the new wheel diameter . 6. 95: Indicates the tire’ s load index. It is an index that relates to how much weight a tire can carry .
next two numbers or letters are the plant code designating where it was manufactured, the next two are the tire size code and the last four numbers represent the week and year the tire was built. For example, the numbers 317 mean the 31st week of 1997.
The tire suppliers may have additional markings, notes or warnings such as standard load, radial tubeless, etc. Additional information contained on the tire sidewall for “L T” type tires “L T” type tires have some additional information beyond those of “P” type tires; these differences are described below: 1.
Information on “T” type tires “T” type tires have some additional information beyond those of “P” type tires; these differences are described below: T145/80D16 is an example of a tire size. Note: The temporary tire size for your vehicle may be different from this example.
the road in adverse (wet, snowy , etc.) conditions. Visually check your tires for uneven wear , looking for high and low areas or unusually smooth areas. Also check for signs of tire damage. When the tread is worn down to 1/16th of an inch (2 mm), tires must be replaced to prevent your vehicle from skidding and hydroplaning.
• A void potholes and objects on the road • Do not run over curbs or hit the tire against a curb when parking If your vehicle is stuck in snow , mud, sand, etc., do not rapidly spin the tires; spinning the tires can tear the tire and cause an explosion.
Tire rotation Rotating your tires at the recommended interval (as indicated in the scheduled maintenance information that comes with your vehicle) will help your tires wear more evenly , providing better tire performance and longer tire life. Unless otherwise specified, rotate the tires approximately every 5,000 miles (8,000 km).
SNOW TIRES AND CHAINS Snow tires must be the same size and grade as the tires you currently have on your vehicle. The tires on your vehicle have all weather treads to provide traction in rain and snow . However , in some climates, you may need to use snow tires and chains.
Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be found on the T ire Label on the B-Pillar or the edge of the driver’ s door . Look for “THE COMBINED WEIGHT OF OCCUP ANTS AND CARGO SHOULD NEVER EXCEED XXX kg OR XXX lb.
Example only: Cargo W eight – includes all weight added to the Base Curb W eight, including cargo and optional equipment. When towing, trailer tongue load or king pin weight is also part of cargo weight.
GA W (Gross Axle W eight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload. GA WR (Gross Axle W eight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear).
GVWR (Gross V ehicle W eight Rating) – is the maximum allowable weight of the fully loaded vehicle (including all options, equipment, passengers and cargo). The GVWR is shown on the Safety Compliance Certification Label located on the B-Pillar or the edge of the driver’ s door .
Maximum Loaded T railer W eight – is the highest possible weight of a fully loaded trailer the vehicle can tow . It assumes a vehicle with only mandatory options, no cargo (internal or external), a tongue load of 10–15% (conventional trailer) or king pin weight of 15–25% (fifth wheel trailer), and driver only (150 lb.
5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4. 6. If your vehicle will be towing a trailer , load from your trailer will be transferred to your vehicle.
Special loading instructions for owners of pickup trucks and utility-type vehicles For important information regarding safe operation of this type of vehicle, see the Preparing to drive your vehicle section in the Driving chapter of this Owner’ s Guide .
GCWR (Gross Combined W eight Rating)/T railer W eights Engine Rear axle ratio Maximum GCWR - lb. (kg) Maximum Loaded T railer W eight - lb. (kg) Maximum frontal area of trailer - ft 2 (m 2 ) E-150 Regular V an (7000 GVWR) 4.6L 3.55 11500 (5216) 6500 (2948) 60 (5.
GCWR (Gross Combined W eight Rating)/T railer W eights Engine Rear axle ratio Maximum GCWR - lb. (kg) Maximum Loaded T railer W eight - lb. (kg) Maximum frontal area of trailer - ft 2 (m 2 ) E-250 Extended V an (7300 GVWR) 4.6L 3.73 11500 (5216) 6000 (2722) 60 (5.
GCWR (Gross Combined W eight Rating)/T railer W eights Engine Rear axle ratio Maximum GCWR - lb. (kg) Maximum Loaded T railer W eight - lb. (kg) Maximum frontal area of trailer - ft 2 (m 2 ) 6.8L 4.10 18500 (8391) 10000 (4536) 60 (5.52) E-350 Extended V an (9400 GVWR) 5.
GCWR (Gross Combined W eight Rating)/T railer W eights Engine Rear axle ratio Maximum GCWR - lb. (kg) Maximum Loaded T railer W eight - lb. (kg) Maximum frontal area of trailer - ft 2 (m 2 ) E-350 Regular W agon (8–passenger) (8600 GVWR) 5.4L 3.73 13000 (5897) 7000 (3175) 60 (5.
GCWR (Gross Combined W eight Rating)/T railer W eights Engine Rear axle ratio Maximum GCWR - lb. (kg) Maximum Loaded T railer W eight - lb. (kg) Maximum frontal area of trailer - ft 2 (m 2 ) E-350 Cutaway (138” wheelbase, dual rear wheel) (10700 GVWR) 5.
GCWR (Gross Combined W eight Rating)/T railer W eights Engine Rear axle ratio Maximum GCWR - lb. (kg) Maximum Loaded T railer W eight - lb. (kg) Maximum frontal area of trailer - ft 2 (m 2 ) E-350 Stripped Chassis (138” wheelbase) (10000 GVWR) 5.4L 4.
GCWR (Gross Combined W eight Rating)/T railer W eights Engine Rear axle ratio Maximum GCWR - lb. (kg) Maximum Loaded T railer W eight - lb. (kg) Maximum frontal area of trailer - ft 2 (m 2 ) E-450 Cutaway (176” wheelbase) (14050 GVWR) 6.8L 4.56 20000 (9072) 10000 (4536) 60 (5.
Note: Do not exceed the GVWR or the GA WR specified on the certification label. T owing trailers beyond the maximum recommended gross trailer weight exceeds the limit of the vehicle and could result in engine damage, transmission damage, structural damage, loss of vehicle control, vehicle rollover and personal injury .
Using a step bumper (if equipped) The rear bumper is equipped with an integral hitch and only requires a ball with a one inch (25.4 mm) shank diameter . The bumper has a 5,000 lb. (2,270 kg) trailer weight and 500 lb. (227 kg) tongue weight capacity .
• If you will be towing a trailer frequently in hot weather , hilly conditions, at GCW , or any combination of these factors, consider refilling your rear axle with synthetic gear lube if not already so equipped. Refer to the Maintenance and specifications chapter for the lubricant specification.
RECREATIONAL TOWING (ALL WHEELS ON THE GROUND) An example of recreational towing would be towing your vehicle on a trip behind a motorhome. Follow these guidelines if you have the need for recreational towing of your vehicle with all four wheels on the ground.
STARTING Positions of the ignition 1. ACCESSORY , allows the electrical accessories such as the radio to operate while the engine is not running. 2. LOCK, locks the automatic transmission gearshift lever and allows key removal. 3. OFF , shuts off the engine and all accessories without locking the steering wheel.
Do not park, idle, or drive your vehicle in dry grass or other dry ground cover . The emission system heats up the engine compartment and exhaust system, which can start a fire. Do not start your vehicle in a closed garage or in other enclosed areas. Exhaust fumes can be toxic.
2. Make sure the headlamps and electrical accessories are off. • Make sure the parking brake is set. • Make sure the gearshift is in P (Park). • T urn the key to 4 (ON) without turning the key to 5 (ST ART). Make sure the corresponding lights illuminate or illuminate briefly .
Starting the engine 1. T urn the key to 4 (ON) without turning the key to 5 (ST ART). 2. T urn the key to 5 (ST ART), then release the key as soon as the engine starts. Excessive cranking could damage the starter . Note: If the engine does not start within five seconds on the first try , turn the key to 3 (OFF), wait 10 seconds and try again.
BRAKES Occasional brake noise is normal. If a metal-to-metal, continuous grinding or continuous squeal sound is present, the brake linings may be worn-out and should be inspected by a qualified service technician.
Parking brake T o set the parking brake (1), press the parking brake pedal down until the pedal stops. T o release, pull the lever (2). Always set the parking brake fully and make sure that the gearshift is securely latched in P (Park). The BRAKE warning lamp will illuminate and will remain illuminated until the parking brake is released.
A high crown in the road or high crosswinds may also make the steering seem to wander/pull. T RACTION-LOK AXLE (IF EQUIPPED) This axle provides added traction on slippery surfaces, particularly when one wheel is on a poor traction surface. Under normal conditions, the T raction-Lok axle functions like a standard rear axle.
shift rearward. As a result, the van has less resistance to rollover and handles differently from other commonly driven passenger vehicles, making it more difficult to control in an emergency situation. Placing any load on the roof also raises the center of gravity and increases the potential for rollover .
• If the vehicle goes from one type of surface to another (i.e., from concrete to gravel) there will be a change in the way the vehicle responds to a maneuver (steering, acceleration or braking).
• Changing lanes on a snow-rutted road. • Entering a snow-free road from a snow-covered side street, or vice versa. • Entering a paved road from a gravel road, or vice versa.
Pressing the control will disable the AdvanceT rac 威 with RSC system and the traction enhancement feature at and below 20 mph (32 km/h). If the vehicle is stuck in snow or mud or when driving in deep sand, switching off the AdvanceT rac 威 with RSC system may be beneficial so the wheels are allowed to spin.
AUTOMATIC TRANSMISSION OPERATION Brake-shift interlock This vehicle is equipped with a brake-shift interlock feature that prevents the gearshift lever from being moved from P (Park) when the ignition is in the ON position unless brake pedal is depressed.
Understanding the gearshift positions of the 4–speed automatic transmission This vehicle is equipped with an adaptive T ransmission Shift Strategy . Adaptive Shift Strategy offers the optimal transmission operation and shift quality .
N (Neutral) W ith the gearshift lever in N (Neutral), the vehicle can be started and is free to roll. Hold the brake pedal down while in this position. (Overdrive) The normal driving position for the best fuel economy . T ransmission operates in gears one through four .
• Selecting 2 (Second) at higher speeds will cause the transmission to downshift to second gear at the appropriate vehicle speed. 1 (First) • Provides maximum engine braking. • Allows upshifts by moving gearshift lever . • W ill not downshift into 1 (First) at high speeds; allows for 1 (First) when vehicle reaches slower speeds.
T o put your vehicle in P (Park): • Come to a complete stop • Move the gearshift lever and securely latch it in P (Park) Always set the parking brake fully and make sure the gearshift is latched in P (Park). T urn the ignition to the LOCK position and remove the key whenever you leave your vehicle.
transmission is in the D (Overdrive) position; this engine braking will slow the vehicle and assist the driver in controlling the vehicle when descending a grade.
Understanding the shift positions of the 5–speed automatic transmission (if equipped - diesel engines only) P (Park) This position locks the transmission and prevents the rear wheels from turning.
D (Drive) without Overdrive D (Drive) without Overdrive can be activated by pressing the transmission control switch (TCS) on the end of the gearshift lever . • This position allows for all forward gears except overdrive. • The OFF lamp on the gearshift lever is illuminated.
If your vehicle goes off the edge of the pavement • If your vehicle goes off the edge of the pavement, slow down, but avoid severe brake application, ease the vehicle back onto the pavement only after reducing your speed. Do not turn the steering wheel too sharply while returning to the road surface.
aftermarket PTO installer since the duration of operation limit for the aftermarket PTO may be less than 10 minutes. A more complete description of PTO operation is discussed in the Ford T ruck Body Builders Layout Book, found at www .fleet.ford.com/truckbbas.
ROADSIDE ASSISTANCE Getting roadside assistance T o fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program.
Using roadside assistance Complete the roadside assistance identification card and place it in your wallet for quick reference. In the United States, this card is found in the Owner Guide portfolio in the glove compartment. In Canada, the card is found in the Owner Information Guide in the glove compartment.
Note: W ith extended use, the flasher may run down your battery . FUEL PUMP SHUT-OFF SWITCH This device stops the electric fuel pump from sending fuel to the engine when your vehicle has had a substantial jolt. After an accident, if the engine cranks but does not start, this switch may have been activated.
On commercial stripped chassis vehicles, this switch is located on a bracket above the brake pedal. T o reset the switch: 1. T urn the ignition OFF . 2. Check the fuel system for leaks. 3. If no leaks are apparent, reset the switch by pushing in on the reset button.
Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 2A Grey Grey — — — 3A Violet Violet — — — 4A Pink Pink — — — 5A T an T an — — — 7.
The fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 1 5A 4–Wheel Anti–lock Brake System (4W ABS) module 2 10A Remote Keyless Entry (RKE.
Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 8 30A Radio capacitor(s), Ignition coil, Powertrain Control Module (PCM) diode, PCM power relay 9 5A Wiper control modu.
Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 32 20A Power point #1 (instrument panel) 33 10A Start relay 34 — Not used 35 — Not used 36 5A Instrument illuminati.
The high-current fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 1 — Powertrain Control Module (PCM) diode 2 — Not used 3 10A* Daytime Running Lamps (DRL) module, A/C clutch 4 5A* Heated PCV (4.6L and 6.
Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 13 20A** Fuel pump relay 14 50A** Auxiliary blower relay 15 30A** Main light switch 16 20A** Injectors (gasoline engines) 17 50A*.
Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description H — Blower motor relay J — Accessory delay relay K — Start relay * Mini fuses ** Maxi fuses Relay modules Instrument panel relay module The instrument panel relay module is located behind the radio in the center of the instrument panel.
Engine compartment relay module The engine compartment relay module is located in one of two places depending on which type of engine your vehicle is equipped with: • Gasoline engine: driver side of the engine compartment above the brake master cylinder .
Dissimilar spare tire/wheel information (if equipped) Failure to follow these guidelines could result in an increased risk of loss of vehicle control, injury or death.
Spare tire information The spare tire for your vehicle is stowed under the rear of your vehicle (except cutaway and stripped chassis models). T o remove the spare tire: 1. Open the rear doors and remove the thumb screw and anti-theft bracket. If finger pressure will not remove the thumb screw , use the lug wrench to loosen the screw .
Tire change procedure Preparing to change the tire T o help prevent the vehicle from moving when you change a tire, be sure the parking brake is set, then block (in both directions) the wheel that is diagonally opposite (other side and end of the vehicle) to the tire being changed.
6. Remove the spare tire and jack from the storage location. • the jack is located in the rear right-hand side of the cargo area. 7. Use the tapered end of the lug nut wrench to unscrew wheel ornaments attached by retaining screws. Remove any wheel trim.
2. Position the jack to raise the front or rear wheel. • Never use the front or rear differential as a jacking point. Rear axle jacking points - All models except E-350 Dual Rear Wheel (DR W) and E-.
Front axle jacking points: Place the jack under the pin on the front surface of the front axle. Do not place the jack under or on the steering linkage. • Raise the jack until the wheel is completely off the ground. (T urn jack handle clockwise if your vehicle is equipped with a screw-type jack or pump the jack if equipped with a hydraulic jack.
• 8-lug wheel Never use wheels or lug nuts different than the original equipment as this could damage the wheel or mounting system. This damage could allow the wheels to come off while the vehicle is being driven. 6. Install any wheel covers, ornaments or hub caps.
5. Repeat this tightness check procedure when servicing the spare tire pressure (every six months, as per your scheduled maintenance information), or at any time that the spare tire is disturbed through service of other components.
When a wheel is installed, always remove any corrosion, dirt or foreign materials present on the mounting surfaces of the wheel or the surface of the front disc brake hub and rotor that contacts the wheel.
4. Check all battery terminals and remove any excessive corrosion before you attach the battery cables. Ensure that vent caps are tight and level. 5. T urn the heater fan on in both vehicles to protect any electrical surges. T urn all other accessories off.
3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery . 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’ s engine, away from the battery and the carburetor/fuel injection system.
Removing the jumper cables Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the ground metal surface. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery .
3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’ s battery . 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’ s battery .
WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or , if you are a member of a roadside assistance program, your roadside assistance service provider . Ford recommends your vehicle be towed with a wheel lift or flatbed.
GETTING THE SERVICES YOU NEED At home Y ou must take your Ford vehicle to an authorized Ford dealer for warranty repairs. While any Ford dealership handling your vehicle line will provide warranty service, we recommend you return to your selling dealer who wants to ensure your continued satisfaction.
In Canada: Customer Relationship Centre Ford Motor Company of Canada, Limited P .O. Box 2000 Oakville, Ontario L6J 5E4 1-800-565-3673 (FORD) www .ford.
In the United States, a warranty dispute must be submitted to the Dispute Settlement Board before taking action under the Magnuson-Moss W arranty Act, or to the extent allowed by state law , before pursuing replacement or repurchase remedies provided by certain state laws.
THE DISPUTE SETTLEMENT BOARD (U.S. ONLY) The Dispute Settlement Board is: • an independent, third-party arbitration program for warranty disputes. • available free to owners and lessees of qualifying Ford Motor Company vehicles. The Dispute Settlement Board may not be available in all states.
Board membership The Board consists of: • Three consumer representatives • A Ford or Lincoln Mercury dealership representative Consumer candidates for Board membership are recruited and trained by an independent consulting firm.
Oral presentations If you would like to make an oral presentation, indicate YES to question 6 on the application. While it is your right to make an oral presentation before the Board, this is not a requirement and the Board will decide the case whether or not an oral presentation is made.
UTILIZING THE MEDIATION/ARBITRATION PROGRAM (CANADA ONLY) For vehicles delivered to authorized Canadian dealerships. In those cases where you continue to feel that the efforts by Ford of Canada and th.
If you did not take advantage of the Ford Extended Service Plan at the time of purchasing your vehicle, you may still be eligible. Since this information is subject to change, please ask your dealer for complete details about Ford Extended Service Plan coverage options, or visit the Ford ESP website at www .
ORDERING ADDITIONAL OWNER’S LITERA TURE T o order the publications in this portfolio, contact Helm, Incorporated at: HELM, INCORPORA TED P .O. Box 07150 Detroit, Michigan 48207 Or call: For a free publication catalog, order toll free: 1-800-782-4356 Monday-Friday 8:00 a.
W ASHING THE EXTERIOR W ash your vehicle regularly with cool or lukewarm water and a neutral pH shampoo, such as Motorcraft Detail W ash (ZC-3–A), which is available from your dealer . • Never use strong household detergents or soap, such as dish washing or laundry liquid.
• Do not allow paint sealant to come in contact with the sliding door electrical contact switches. Paint sealant or other contaminants could interfere with the proper operation of the power locks or radio speakers. If necessary , clean the contacts with Motorcraft Bug and T ar Remover (ZC-42) to remove any sealant.
• Do not spray a hot engine with cold water to avoid cracking the engine block or other engine components. • Spray Motorcraft Engine Shampoo and Degreaser (ZC-20) on all parts that require cleaning and pressure rinse clean. • Cover the highlighted areas to prevent water damage when cleaning the engine.
• Do not use abrasives, as they may cause scratches. • Do not use fuel, kerosene, or paint thinner to clean any parts. • W iper blades can be cleaned with isopropyl (rubbing) alcohol or windshield washer solution. Be sure to replace wiper blades when they appear worn or do not function properly .
Do not use cleaning solvents, bleach or dye on the vehicle’ s seatbelts, as these actions may weaken the belt webbing. LEATHER SEATS (IF EQUIPPED) Y our leather seating surfaces have a clear , protective coating over the leather . • T o clean, use a soft cloth with Motorcraft Deluxe Leather and Vinyl Cleaner (ZC-11–A).
Motorcraft Deluxe Leather and Vinyl Cleaner (U.S. only) (ZC-11–A) Motorcraft Detail W ash (ZC-3–A) Motorcraft Dusting Cloth (ZC-24) Motorcraft Engine Shampoo and Degreaser (U.
SERVICE RECOMMENDATIONS T o help you service your vehicle: • W e highlight do-it-yourself items in the engine compartment for easy location. • W e provide scheduled maintenance information which makes tracking routine service easy . If your vehicle requires professional service, your dealership can provide the necessary parts and service.
OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the bottom left corner of the instrument panel. 2. Go to the front of the vehicle and release the auxiliary latch that is located in the center top of the grill. 3. Lift the hood and secure it with the prop rod.
IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT Engine compartment component locations Refer to the 6.0 Liter Power Stroke Direct Injection T urbo Diesel Owner’ s Guide Supplement for diesel engine component locations. 1. W indshield washer fluid reservoir 2.
WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if the level is low . In very cold weather , do not fill the reservoir completely . Only use a washer fluid that meets Ford specification WSB-M8B16–A2. Refer to Lubricant specifications in this chapter .
5. Locate and carefully remove the engine oil level indicator (dipstick). 6. W ipe the indicator clean. Insert the indicator fully , then remove it again.
• Do not overfill the engine with oil. Oil levels above this mark may cause engine damage. If the engine is overfilled, some oil must be removed from the engine by a qualified service technician. 7. Put the indicator back in and ensure it is fully seated.
economy requirements of the International Lubricant Standardization and Approval Committee (ILSAC), comprised of U.S. and Japanese automobile manufacturers. T o protect your engine’ s warranty use Motorcraft SAE 5W -20 or an equivalent 5W -20 oil meeting Ford specification WSS-M2C930-A.
If the electrolyte level in the battery is low , you can add plain tap water to the battery , as long as you do not use hard water (water with a high mineral or alkali content). If possible, however , try to only fill the battery cells with distilled water .
Keep batteries out of reach of children. Batteries contain sulfuric acid. A void contact with skin, eyes or clothing. Shield your eyes when working near the battery to protect against possible splashing of acid solution.
If the battery has been disconnected or a new battery has been installed, the clock and radio settings must be reset once the battery is reconnected. • Always dispose of automotive batteries in a responsible manner . Follow your local authorized standards for disposal.
When the engine is cold, check the level of the engine coolant in the reservoir . • The engine coolant should be at the “FULL COLD” level or within the “COLD FILL RANGE” as listed on the engine coolant reservoir (depending upon application).
Do not add engine coolant when the engine is hot. Steam and scalding liquids released from a hot cooling system can burn you badly . Also, you can be burned if you spill coolant on hot engine parts. Do not put engine coolant in the windshield washer fluid container .
coolant degas system with a pressurized cap, or if it is necessary to remove the coolant pressure relief cap on the radiator of a vehicle with an overflow system, follow these steps to add engine coolant. T o reduce the risk of personal injury , make sure the engine is cool before unscrewing the coolant pressure relief cap.
Used engine coolant should be disposed of in an appropriate manner . Follow your community’ s regulations and standards for recycling and disposing of automotive fluids. Coolant refill capacity T o find out how much fluid your vehicle’ s cooling system can hold, refer to Refill capacities in this section.
What you should know about fail-safe cooling (if equipped) If the engine coolant supply is depleted, this feature allows the vehicle to be driven temporarily before incremental component damage is incurred. The “fail-safe” distance depends on ambient temperatures, vehicle load and terrain.
Never remove the coolant reservoir cap while the engine is running or hot. 5. Re-start the engine and take your vehicle to a service facility . Driving the vehicle without repairing the engine problem increases the chance of engine damage. T ake your vehicle to a service facility as soon as possible.
Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materials and any open flames before refueling your vehicle. • Always turn off the vehicle before refueling. • Automotive fuels can be harmful or fatal if swallowed.
Refueling Fuel vapor burns violently and a fuel fire can cause severe injuries. T o help avoid injuries to you and others: • Read and follow all the instructions on the pump island; • T urn off yo.
If you must replace the fuel filler cap, replace it with a fuel filler cap that is designed for your vehicle. The customer warranty may be void for any damage to the fuel tank or fuel system if the correct genuine Ford or Motorcraft fuel filler cap is not used.
Do not be concerned if your engine sometimes knocks lightly . However , if it knocks heavily under most driving conditions while you are using fuel with the recommended octane rating, see your dealer or a qualified service technician to prevent any engine damage.
Fuel Filter For fuel filter replacement, see your dealer or a qualified service technician. Refer to scheduled maintenance information for the appropriate intervals for changing the fuel filter . Replace the fuel filter with an authorized Motorcraft part.
• Always use fuel with the recommended octane rating. • Use a known quality gasoline, preferably a national brand. • Use the same side of the same pump and have the vehicle facing the same direction each time you fill up. • Have the vehicle loading and distribution the same every time.
• Slow down gradually . • Driving at reasonable speeds (traveling at 55 mph [88 km/h] uses 15% less fuel than traveling at 65 mph [105 km/h]). • Revving the engine before turning it off may reduce fuel economy . • Using the air conditioner or defroster may reduce fuel economy .
• T ransmissions give their best fuel economy when operated in the top cruise gear and with steady pressure on the gas pedal. • Close windows for high speed driving. EP A window sticker Every new vehicle should have the EP A window sticker . Contact your dealer if the window sticker is not supplied with your vehicle.
Illumination of the indicator , charging system warning light, fluid leaks, strange odors, smoke or loss of engine power , could indicate that the emission control system is not working properly . Exhaust leaks may result in entry of harmful and potentially lethal fumes into the passenger compartment.
Readiness for Inspection/Maintenance (I/M) testing In some localities, it may be a legal requirement to pass an I/M test of the on-board diagnostics system. If your Check engine/Service engine soon light is on, refer to the description in the W arning lights and chimes section of the Instrument Cluster chapter .
POWER STEERING FLUID Check the power steering fluid. Refer to the scheduled maintenance guide for the service interval schedules. If adding fluid is necessary , use only MERCON 威 AT F . Check the fluid level when it is at ambient temperature, 20° – 80° F (-7° – 25° C): 1.
6. If the fluid is low , add fluid in small amounts, continuously checking the level until it reaches the FULL COLD range. Be sure to put the dipstick back in the reservoir . BRAKE FLUID The fluid level will drop slowly as the brakes wear , and will rise when the brake components are replaced.
4. Latch the gearshift lever in P (Park) and leave the engine running. 5. Remove the dipstick, wiping it clean with a clean, dry lint free rag. If necessary , refer to Identifying components in the engine compartment in this chapter for the location of the dipstick.
Adjusting automatic transmission fluid levels Before adding any fluid, make sure the correct type is used. The type of fluid used is normally indicated on the dipstick and also in the Lubricant specifications section in this chapter . Use of a non-approved automatic transmission fluid may cause internal transmission component damage.
Automatic transmission fluid filter (if equipped) The T orqShift automatic transmission is equipped with a serviceable external fluid filter mounted on the driver’ s side of the transmission. Refer to the scheduled maintenance information for service intervals.
Changing the air filter element 1. Disconnect the fresh air inlet tube from the radiator support. 2. Open the clamp that secures the two halves of the air filter housing together . 3. Carefully separate the two halves of the air filter housing. 4. Remove the air filter element from the housing.
Component 1 4.6L V8 engine 5.4L V8 engine 6.8L V10 engine Oil filter FL-820-S FL-820-S FL-820-S PCV valve 2 Spark plugs 3 Automatic transmission filter 4 — FT -145 FT -145 1 Refer to the Power Stroke Direct Injection T urbo Diesel Owner’ s Guide Supplement for Motorcraft diesel engine service part numbers.
REFILL CAPACITIES Fluid Ford Part Name Application Capacity Brake Fluid Motorcraft High Performance DOT 3 Motor V ehicle Brake Fluid All Fill to line on reservoir Engine oil-gasoline engine (includes filter change) 8 Motorcraft SAE 5W -20 Premium Synthetic Blend Motor Oil (US) Motorcraft SAE 5W -20 Super Premium Motor Oil (Canada) All 6.
Fluid Ford Part Name Application Capacity Power steering fluid Motorcraft MERCON 威 AT F All Keep in FULL range on dipstick Rear axle SAE 75W -140 Synthetic Rear Axle Lubricant 2 , 4 Visteon 8.8/9.75 inch conventional and T raction-Lok 5.5 pints (2.6L) 3 Dana M70 (M248) E-350 conventional and Limited Slip 6.
Fluid Ford Part Name Application Capacity Fuel T ank N/A All regular and extended length vans and wagons 35.0 gallons (132.4L) 138 inch wheelbase (except E-Super Duty) 37.0 gallons (140.0L) 158 inch wheelbase (except E-Super Duty) 37.0 gallons (140.0L) 5 176 inch wheelbase (except E-Super Duty) 37.
3 Fill Dana rear axles to 1/4 inch to 9/16 inch (6 mm to 14 mm) below bottom of fill hole. Fill Visteon axles 1/4 inch to 9/16 inch (6 mm to 14 mm) below bottom of fill hole. 4 Visteon T raction-Lok axles require 4 oz. (118 ml) of Additive Friction Modifier XL–3 or equivalent.
LUBRICANT SPECIFICATIONS Item Ford part name Ford part number Ford specification Brake fluid Motorcraft High Performance DOT 3 Motor V ehicle Brake Fluid PM-1 ESA-M6C25-A or WSS-M6C62–A Door weatherstrips Silicone Lubricant XL-6 ESR-M13P4-A Engine coolant Motorcraft Premium Gold Engine Coolant (yellow-colored) VC-7-A (U.
Item Ford part name Ford part number Ford specification Automatic transmission (4R70/75 E) 1 Motorcraft MERCON 威 V AT F XT -5-QM MERCON 威 V Automatic transmission T orqShift (5–speed) 1 Motorcra.
Item Ford part name Ford part number Ford specification Dana conventional axles M60 (M248) E-250/350 M70FF (M267FF) E-350 M70HD (M273HD) E-450 SAE 80W -90 Premium Rear Axle Lubricant XY -80W90–QL WS.
ENGINE DATA Engine * 4.6L V8 engine 5.4L V8 engine 6.8L V10 engine Cubic inches 281 330 415 Required fuel 87 octane 87 octane 87 octane Firing order 1-3-7-2-6-5-4-8 1-3-7-2-6-5-4-8 1-6-5-10-2-7-3-8-4-9 Ignition system C o i lo np l u g C o i lo np l u g C o i lo np l u g Spark plug gap 0.
4 5 2006 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus) Maintenance and Specifications 238.
Cutaway/commercial stripped chassis models E-350 – inches (mm) E-450 – inches (mm) (1) Overall height Refer to Body Builder for specifications. (2) T rack front/rear Cutaway: 69.4 (1763) SRW : 72.1 (1831) DRW : 73.2 (1860) Stripped Chassis: 69.4 (1763) SRW : 72.
Certification label for incomplete vehicles On completed derivations of incomplete vehicles, the certification label is affixed at a location determined by a subsequent stage manufacturer of the completed vehicle. In these cases the completed vehicle is manufactured in two or more stages by two or more separate manufacturers.
GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for your vehicle through your local authorized Ford or Ford of Canada dealer .
Lifestyle Mobile-ease hands-free communication system T railer hitches, wiring harnesses and accessories Peace of mind First aid and highway safety kits Keyless entry keypad Remote start V ehicle secu.
A Accessory delay .......................... 48 AdvanceT rac .............................. 143 Air cleaner filter ............... 227–228 Airbag supplemental restraint system .......................................... 74 and child safety seats ....
wiper blades ............................ 193 Climate control (see Air conditioning or Heating) ......30, 32 Clock adjust 6-CD in dash .......................21, 26 AM/FM ....................................... 19 Compass, electronic .................
F Fail safe cooling ........................ 211 Fluid capacities ......................... 230 Four -Wheel Drive vehicles preparing to drive your vehicle ..................................... 141 Fuel ............................................ 212 calculating fuel economy .
interior lamps ........................... 37 replacing bulbs ................... 38–42 Lane change indicator (see T urn signal) ........................ 37 Lights, warning and indicator .... 12 anti-lock brakes (ABS) .......... 139 Load limits ....
Spare tire (see Changing the T ire) ........... 169 Spark plugs, specifications .....................228, 237 Special notice ................................ 8 ambulance conversions .............. 7 diesel-powered vehicles ............. 7 utility-type vehicles .
248.
Een belangrijk punt na aankoop van elk apparaat Ford 2006 E-150 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Ford 2006 E-150 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Ford 2006 E-150 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Ford 2006 E-150 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Ford 2006 E-150 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Ford 2006 E-150 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Ford 2006 E-150 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Ford 2006 E-150 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.