Gebruiksaanwijzing /service van het product 2006 Five Hundred van de fabrikant Ford
Ga naar pagina of 272
Introduction 4 Instrument Cluster 10 W arning and control lights 10 Gauges 14 Entertainment Systems 17 AM/FM stereo with CD 17 AM/FM stereo with in-dash six CD 20 Family entertainment system 25 Climat.
Seating and Safety Restraints 100 Seating 100 Safety restraints 107 Airbags 120 Child restraints 134 Tires, Wheels and Loading 146 T ire Information 146 T ire Inflation 148 V ehicle loading 160 T rail.
Maintenance and Specifications 226 Engine compartment 228 Engine oil 230 Battery 233 Engine Coolant 235 Fuel information 241 Part numbers 255 Refill capacities 256 Lubricant specifications 258 Accessories 264 Index 267 All rights reserved.
CALIFORNIA Proposition 65 W arning W ARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
SAFETY AND ENVIRONMENT PROTECTION W arning symbols in this guide How can you reduce the risk of personal injury to yourself or others? In this guide, answers to such questions are contained in comments highlighted by the warning triangle symbol. These comments should be read and observed.
SPECIAL NOTICES New V ehicle Limited W arranty For a detailed description of what is covered and what is not covered by your vehicle’ s New V ehicle Limited W arranty , refer to the Warranty Guide that is provided to you along with your Owner’ s Guide.
Please read the section Supplemental restraint system (SRS) in the Seating and Safety Restraints chapter . Failure to follow the specific warnings and instructions could result in personal injury . Front seat mounted rear -facing child or infant seats should NEVER be placed in front of an active passenger airbag.
These are some of the symbols you may see on your vehicle. V ehicle Symbol Glossary Safety Alert See Owner’ s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat Child Seat Installation.
V ehicle Symbol Glossary Power W indows Front/Rear Power W indow Lockout Child Safety Door Lock/Unlock Interior Luggage Compartment Release Symbol Panic Alarm Engine Oil Engine Coolant Engine Coolant .
W ARNING LIGHTS AND CHIMES W arning lights and gauges can alert you to a vehicle condition that may become serious enough to cause extensive repairs. A warning light may illuminate when a problem exists with one of your vehicle’ s functions. Many lights will illuminate when you start your vehicle to make sure the bulbs work.
Check fuel cap (if equipped): Illuminates when the fuel cap may not be properly installed. Continued driving with this light on may cause the Check engine warning light to come on, refer to Fuel filler cap in the Maintenance and Specification chapter .
Safety belt: Reminds you to fasten your safety belt. A chime will also sound to remind you to fasten your safety belt. Charging system: Illuminates when the battery is not charging properly . Engine oil pressure: Illuminates when the oil pressure falls below the normal range, refer to Engine oil in the Maintenance and Specifications chapter .
Speed control: Illuminates when the speed control is engaged. T urns off when the speed control system is disengaged. Low washer fluid (if equipped): Illuminates when the windshield washer fluid is low . Door ajar (if equipped): Illuminates when the ignition is in the ON position and any door or decklid is open.
GAUGES Speedometer: Indicates the current vehicle speed. Engine coolant temperature gauge: Indicates engine coolant temperature. At normal operating temperature, the needle will be in the normal range (between “H” and “C”). If it enters the red section, the engine is overheating.
Fuel gauge: Indicates approximately how much fuel is left in the fuel tank (when the ignition is in the ON position). The fuel gauge may vary slightly when the vehicle is in motion or on a grade. The FUEL icon and arrow indicates which side of the vehicle the fuel filler door is located.
• W ith Message Center T o reset with the ODO/TRIP button: • T ap on the button to toggle the display between the trip and the odometer . Holding the ODO/TRIP button for two seconds or more will reset the trip odometer to zero. T o reset with the message center buttons: • Select the TRIP function from the INFO menu.
AUDIO SYSTEMS AM/FM stereo/ single CD sound system (if equipped) Accessory delay: Y our vehicle is equipped with accessory delay . W ith this feature, the window switches and radio may be used for up to ten minutes after the ignition is turned off or either front door is opened.
Autoset: Allows you to set the strongest local radio stations without losing your original manually set preset stations for AM/FM1/FM2 . Press MENU to access. Use / / SEEK to set. When the six strongest stations are filled, the station stored in preset 1 will begin playing.
9. Repeat: Press to repeat the current CD track. 10. Fast forward: Press to manually advance in a CD track. 11. Rewind: Press to manually reverse in a CD track. 12. Memory presets: T o set a station: Select frequency band AM/FM; tune to a station, press and hold a preset button until sound returns.
19. CD slot: Insert a CD label side up. Premium/Audiophile In-Dash Six CD/MP3 Sound System (if equipped) Accessory delay: Y our vehicle is equipped with accessory delay . W ith this feature, the window switches and radio may be used for up to ten minutes after the ignition switch is turned off or until either front door is opened.
3. Menu: Press to toggle through the following modes: Autoset: Allows you to set the strongest local radio stations without losing your original manually set preset stations for AM/FM1/FM2 . Use / / SEEK to turn on/off. When the six strongest stations are filled, the station stored in preset 1 will begin playing.
Repeat: A vailable only in CD mode. Press to repeat the current CD track. RDS (A vailable on Audiophile radios only): Allows you to search RDS-equipped stations for a certain category of music format: Classic, Country , Info, Jazz/RB, Religious, Rock, Soft, T op 40.
10. Fast forward: Press to manually advance in a CD track. 11. Rewind: Press to manually reverse in a CD track. 12. Memory presets: T o set a station: Select frequency band AM/FM; tune to a station, press and hold a preset button until sound returns. 13.
20. CD slot: Insert a CD label side up. GENERAL AUDIO INFORMATION Radio frequencies: AM and FM frequencies are established by the Federal Communications Commission (FCC) and the Canadian Radio and T elecommunications Commission (CRTC). Those frequencies are: AM: 530, 540–1700, 1710 kHz FM: 87.
become jammed. It is recommended that homemade CDs be identified with permanent felt tip marker rather than adhesive labels. Ballpoint pens may damage CDs. Please contact your authorized dealer for further information. Audio system warranty and service Refer to the W arranty Guide for audio system warranty information.
• FWD — Press to advance within the active CD track or DVD chapter in play mode. Also press to move the cursor right in the menu active mode. 2. PLA Y/P AUSE control Press to playback or pause the DVD. 3. DIM control Press (+) to increase or (-) to decrease the brightness on the screen.
• Press the NEXT control to move the cursor one position upward • Press the PREV control to move the cursor one position downward • Press the REV control to move the cursor left one position •.
Enter control The ENTER control allows you to select highlighted items when in MENU mode. CD play mode Press NEXT during CD play to advance to the next track. If you press NEXT while the last track is playing, the system will wrap around to the first track and begin play .
Remote control 1. REV (REVERSE) control Press to reverse the direction of the DVD movie. 2. FWD (FOR W ARD) control Press to advance the direction of the DVD movie. 3. PLA Y/STOP control When playing, press PLA Y/STOP to stop the disc. When stopped, press PLA Y/STOP to play the disc.
In DVD playback mode, press to access the disc menu. In stop mode, press to change media types (e.g. AM, FM, C D...) 8. VOL (VOLUME) control Press (+) to increase or (-) to decrease the volume level. Dual play mode Press the radio preset controls 2 and 4 at the same time to enable or disable dual play .
Battery replacement Batteries are provided with the remote control unit. Since all batteries have a limited shelf life, replace them when the remote control fails to control the DVD player . There is a LED indicator light on the remote control that will illuminate when any control is pressed.
Wireless headphones Y our system is equipped with 2 sets of wireless headphones. (T wo AAA batteries are needed to operate the headphones.) Batteries are included. T o install the batteries, remove the screw at the bottom of the cover . Then, lightly press down on top, and slide the cover off.
Note: The volume level of the wireless headphones can only be controlled by the thumbwheel. Neither the remote control nor the rear seat controls will affect the volume output of the wireless headphones. When not using the headphones, turn them off to preserve battery life.
3. Dimmer switch. Press +/- to increase/decrease the brightness of the display . Playback and format • The DVD player of your Family Entertainment DVD System can only be used in the “playback” mode. (The DVD player does not offer a record feature.
This unit is designed to play commercially pressed 4.75 (12 cm) audio compact discs and DVDs only . Due to technical incompatibility , certain recordable and re-recordable compact discs may not function correctly when used in Ford DVD/CD players.
On-screen indicators Each time a control is pressed, the operational status of the DVD player is shown on the screen. The following are some possible indicators: 1. DVD/ CD ST A TUS (PLA Y/FWD/REV/P AUSE) 2. CD track number / DVD title 3. DVD chapter number 4.
The front glass on the flip-down liquid crystal display (LCD) may break when hit with a hard surface. If the glass breaks, do not touch the liquid crystalline material.
However , there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, (which can be determined by turning the equipment off and on), the user is encouraged to consult the dealer or an experienced radio/TV technician for help.
Cleaning compact discs Inspect all discs for contamination before playing. If necessary , clean discs only with an approved CD cleaner and wipe from the center out to the edge. Do not wipe in a circular motion. Cleaning the DVD player Clean the exterior of the DVD player with a damp cloth.
MANUAL HEATING AND AIR CONDITIONING SYSTEM (IF EQUIPPED) 1. T emperature selection: Controls the temperature of the airflow in the vehicle. 2. Air flow selections: Controls the direction of the airflow in the vehicle.
6. Fan speed adjustment: Controls the volume of air circulated in the vehicle. Operating tips • T o reduce fog build up on the windshield during humid weather , place the air flow selector in the position. • T o reduce humidity build up inside the vehicle: do not drive with the airflow selector in the O (OFF) or with recirculated air engaged.
DUAL ZONE AUTOMATIC T EMPERATURE CONTROL (IF EQUIPPED) 1. Defrost: Distributes outside air through the windshield defroster and demister vents. Can be used to clear thin ice or fog from the windshield.
8. : Distributes air through the instrument panel and floor vents. 9. : Distributes air through the instrument panel vents. 10. Manual override controls: Allows you to manually select where airflow is directed. T o return to full automatic control, press AUTO.
Dual Zone Automatic T emperature Control with heated seats (if equipped) 1. Defrost: Distributes outside air through the windshield defroster and demister vents. Can be used to clear thin ice or fog from the windshield. T o exit select another mode. 2.
7. A/C: Press to activate/deactivate air conditioning. Use with recirculated air to improve cooling performance and efficiency . Engages automatically in AUTO, defrost and floor/defrost. 8. Airflow direction control: Press to toggle through the air distribution modes listed below .
Operating tips • T o reduce fog build up on the windshield during humid weather , place the air flow selector in the position. • T o reduce humidity build up inside the vehicle: do not drive with the airflow selector in the OFF or with recirculated air engaged.
REAR WINDOW DEFROSTER R The rear defroster control is located on the climate control panel and works to clear the rear window of fog and thin ice. The ignition must be in the 3 (RUN) position to operate the rear window defroster . The rear defroster turns off automatically after 10 minutes or when the ignition is turned to the 1 (LOCK) position.
HEADLAMP CONTROL T urns the lamps off. T urns on the parking lamps, instrument panel lamps, license plate lamps and tail lamps. T urns the headlamps on. Autolamp control (if equipped) The autolamp system provides light sensitive automatic on-off control of the exterior lights normally controlled by the headlamp control.
5. W ait the desired amount of time for the exit delay you want (up to three minutes), then turn the headlamp switch to . The headlamps will turn off. High beams Pull the lever towards you, to the second detent, to activate. Pull the lever towards you again to deactivate.
Daytime running lamps (DRL) (if equipped) T urns the headlamps on with a reduced output. T o activate: • the ignition must be in the ON position, • the headlamp control is in the OFF , autolamps or parking lamp position and • the transmission must be out of the Park position.
• (1) 8 feet (2.4 meters) • (2) Center height of lamp to ground • (3) 25 feet (7.6 meters) • (4) Horizontal reference line 2. Measure the height of the headlamp bulb center from the ground and mark an 8 foot (2.5 meter) horizontal reference line on the vertical wall or screen at this height (a piece of masking tape works well).
TURN SIGNAL CONTROL • Push down to activate the left turn signal. • Push up to activate the right turn signal. INTERIOR LAMPS Dome lamps and map lamps The map lamps are located on the overhead console. Press the controls on either side of each map lamp to turn on the lamps.
“E” for Europe to assure lamp performance, light brightness and pattern and safe visibility . The correct bulbs will not damage the lamp assembly or void the lamp assembly warranty and will provide quality bulb burn time.
3. Locate the outboardmost top electrical connector and remove it by releasing the locking tab and pulling it straight down. 4. Remove the bulb socket by turning it counterclockwise and pulling it straight out. Handle a halogen headlamp bulb carefully and keep out of children’ s reach.
Replacing front parking lamp/turn signal bulbs 1. Make sure headlamp switch is in the OFF position, then open the hood. 2. Reach up from the underside of the fascia to access the bulb sockets and connectors. 3. Locate the parking/turn signal lamp electrical connector and remove it by pulling it straight off.
4. Remove the bulb socket by rotating it counterclockwise, then pulling it out of the lamp assembly . 5. Pull the bulb straight from the socket. Install new bulb(s) in reverse order . Replacing high-mount brake lamp bulbs 1. Make sure the ignition control is in the OFF position.
Replacing foglamp bulbs 1. Make sure the foglamp switch is in the OFF position. 2. Remove the bulb socket from the foglamp by turning counterclockwise.
MUL TI-FUNCTION LEVER W indshield wiper: For intermittent operation, move control up one position. Adjust the rotary control to the desired speed setting. Mist function: T o activate mist, push control down from the OFF position and release to get one wipe.
TILT STEERING WHEEL T o adjust the steering wheel: 1. Pull down and hold the steering wheel release control. 2. Move the steering wheel up or down until you find the desired location. 3. Pull the steering wheel release control up. This will lock the steering wheel in position.
CLOCK (IF EQUIPPED) Press and release the button to adjust forward. Press and hold to fast forward. INSTRUMENT PANEL STORAGE COMPARTMENT The storage compartment may be used to secure sunglasses or similar sized objects. Press the control to open the storage compartment.
The auxiliary power points are located on the instrument panel and in the center console utility compartment. Do not use the power point for operating the cigarette lighter element (if equipped). T o prevent the fuse from being blown, do not use the power point(s) over the vehicle capacity of 12 VDC/180W .
Press and pull the window switches to open and close windows. • Push down (to the first detent) and hold the switch to open. • Pull up (to the first detent) and hold the switch to close. One touch up or down This feature is present on the driver’ s window only .
Window lock The window lock feature allows only the driver to operate the power windows. T o lock out all the window controls except for the driver’ s press the right side of the control.
(darkened) state when bright lights (glare) reach the mirror . When the mirror detects bright light from behind the vehicle, it will automatically adjust (darken) to minimize glare. The mirror will automatically return to the normal state whenever the vehicle is placed in R (Reverse) to ensure a bright clear view when backing up.
Heated outside mirrors (if equipped) Both mirrors are heated automatically to remove ice, mist and fog when the rear window defrost is activated. Do not remove ice from the mirrors with a scraper or attempt to readjust the mirror glass if it is frozen in place.
Do not use the speed control in heavy traffic or on roads that are winding, slippery or unpaved. Setting speed control The controls for using your speed control are located on the steering wheel for your convenience. 1. Press the ON control and release it.
Resuming a set speed Press the RES control and release it. This will automatically return the vehicle to the previously set speed. The RES control will not work if the vehicle speed is not faster than 30 mph (48 km/h).
• Depress the brake pedal or press CNCL (Cancel) until the desired vehicle speed is reached, press the SET + control. Turning of f speed control There are two ways to turn off the speed control: • Depress the brake pedal or press CNCL (Cancel). This will not erase your vehicle’ s previously set speed.
In Radio mode: • Press SEEK to access the next/previous strong station. In CD mode: • Press SEEK to listen to the next track on the disc. In any mode: • Press VOL up or down to adjust the volume.
The moon roof has a sliding shade that can be opened or closed when the glass panel is shut. T o close the shade, pull it toward the front of the vehicle Do not let children play with the moon roof or leave children unattended in the vehicle. They may seriously hurt themselves.
transmitter of the device being programmed to HomeLink 威 for quicker training and accurate transmission of the radio-frequency signal. 1. Press and hold the two outside buttons releasing only when the indicator light begins to flash after 20 seconds.
7. Press and release the “learn” or “smart” button. (The name and color of the button may vary by manufacturer .) Note: There are 30 seconds in which to initiate Step 8. 8. Return to the vehicle and firmly press, hold for two seconds and release the HomeLink 威 button.
Operating the HomeLink 姞 Wireless Control System T o operate, simply press and release the appropriate HomeLink 威 button. Activation will now occur for the trained product (garage door , gate operator , security system, entry door lock, or home or office lighting etc.
MESSAGE CENTER (IF EQUIPPED) W ith the ignition in the ON position, the message center , located on your instrument cluster , displays important vehicle information through a constant monitor of vehicle systems. Y ou may select display features on the message center for a display of status.
DTE is calculated using a running average fuel economy , which is based on your recent driving history of 500 miles (800 km). This value is not the same as the average fuel economy display . The running average fuel economy is reinitialized to a factory default value if the battery is disconnected.
Trip elapsed drive time Select this function from the INFO menu to display a timer . T o operate the T rip Elapsed Drive T ime perform the following: 1. Press and release RESET in order to start the timer . 2. Press and release RESET to pause the timer .
Note: If message center displays the message ⬙ SLOW CIRCLES TO CALIBRA TE ⬙ , then perform the CALIBRA TION PROCEDURE. 4. Determine your magnetic zone by referring to the zone map. 5. Press and hold the RESET until the message center display changes to show the current zone setting.
Note: If message center displays the message ⬙ SLOW CIRCLES TO CALIBRA TE ⬙ , then continue with Step 4. Otherwise, if a heading is displayed, continue with Step 5.
3. Press and hold the RESET control to set the language choice. Units (English/Metric) 1. Select this function from the SETUP menu for the current units to be displayed.
The message center will display the last selected feature if there are no more warning messages. This allows you to use the full functionality of the message center after you acknowledge the warning by pressing the RESET control and clearing the warning message.
P ARK BRAKE ENGAGED. Displayed when the park brake is engaged. If the warning stays on after the park brake is off, contact your authorized dealer as soon as possible. LOW FUEL LEVEL. Displayed as an early reminder of a low fuel condition. CHECK CHARGING SYSTEM.
T o reset the oil life to 100% with system warnings CHANGE OIL SOON/OIL CHANGE REQUIRED displayed: 1. Select this function from the SETUP control for current display mode. 2. Press and release the RESET control to display “IF NEW OIL HOLD RESET”. 3.
INTERIOR TRUNK CONTROL Press the remote trunk release control on the instrument panel to the left of the steering wheel. CARGO AREA FEATURES Cargo net (if equipped) The cargo net secures lightweight objects in the cargo area. Attach the net to the anchors provided.
KEYS One key operates all the locks and starts the vehicle. Always carry a spare key with you in case of an emergency . Y our keys are programmed to your vehicle; using a non-programmed key will not permit your vehicle to start. If you lose your authorized dealer supplied keys, replacement keys are available through your authorized dealer .
1. Place the key in the ignition and turn the ignition to the 3 (RUN) position. 2. Press the power door unlock control on the door panel three times. 3. T urn the ignition from the 3 (RUN) position to the 1 (LOCK) position. 4. Press the power door unlock control on the door panel three times.
Adults are advised to familiarize themselves with the operation and location of the release handle. T o open the luggage compartment door (lid) from within the luggage compartment, pull the illuminated “T” shaped handle and push up on the trunk lid.
REMOTE ENTRY SYSTEM This device complies with part 15 of the FCC rules and with RS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
2. Press and release again within three seconds to unlock all the doors. The remote entry system activates the illuminated entry feature; this feature turns on the lamps for 25 seconds or until the ignition is turned to the 3 (RUN) position.
Press to automatically move the seat, mirrors and adjustable pedals to the desired memory position (the positions correspond to the transmitter being used).
2. Do not wipe off any grease on the battery terminals on the back surface of the circuit board. 3. Remove the old battery . Note: Please refer to local regulations when disposing of transmitter batteries. 4. Insert the new battery . Refer to the diagram inside the remote entry transmitter for the correct orientation of the battery .
T o reprogram the remote entry transmitters: 1. Ensure the vehicle is electronically unlocked. 2. Put the key in the ignition. 3. Cycle eight times rapidly (within 10 seconds) between the 1 (LOCK) position and 3 (RUN). Note: The eighth turn must end in the 3 (RUN) position.
• If the dome lamps were turned on using the panel dimmer control, the battery saver will shut off them off 30 minutes after the ignition has been turned to the 1 (LOCK) position.
2. W ithin five seconds press the 1 • 2 on the keypad. 3. Enter your personal 5-digit code. Each number must be entered within five seconds of each other .
Unlocking and locking the doors using keyless entry T o unlock the driver’ s door , enter the factory set 5-digit code or your personal code. Each number must be pressed within five seconds of each other .
Power door unlock/lock procedure Y ou must complete steps 1-5 within 30 seconds or the procedure will have to be repeated. If the procedure needs to be repeated, you must wait 30 seconds. 1. T urn the ignition to the 3 (RUN) position. 2. Press the power door unlock control three times.
Note: The SecuriLock 娂 passive anti-theft system is not compatible with non-Ford aftermarket remote start systems. Use of these systems may result in vehicle starting problems and a loss of security protection.
Replacement keys If your keys are lost or stolen and you don’t have an extra coded key , you will need to have your vehicle towed to an authorized dealer . The key codes need to be erased from your vehicle and new coded keys will need to be programmed.
6. T urn the ignition to the 1 (LOCK) position and remove the second previously programmed coded key from the ignition. 7. W ithin twenty seconds of turning the ignition to the 1 (LOCK) position and removing the previously programmed coded key , insert the new unprogrammed key (new key/valet key) into the ignition.
• Press the driver or passenger interior door lock control while the door is open, then close the door . • Press the 7 • 8a n d9 • 0 controls on the keyless entry pad at the same time to lock the doors (driver’ s door must be closed). There is a 20 second countdown when any of the above actions occur before the vehicle becomes armed.
SEATING Notes: Reclining the seatback can cause an occupant to slide under the seat’ s safety belt, resulting in severe personal injuries in the event of a collision. Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop.
Using the manual lumbar support (if equipped) The lumbar support control is located on the outboard side of the seatback. Move the control up or down to adjust lumbar support. Folding down the front passenger seatback The front passenger seatback can be folded to a horizontal position to make room for a long load.
Adjusting the front manual seat (if equipped) Never adjust the driver’ s seat or seatback when the vehicle is moving. Always drive and ride with your seatback upright and the lap belt snug and low across the hips. Lift handle to move seat forward or backward.
Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop. Always drive and ride with your seatback upright and the lap belt snug and low across the hips.
Press the control to move the seat forward, backward, up or down. • Driver Press the control to move the seat forward, or backward. • Passenger Press the control (if equipped) to recline the seatback forward or rearward.
Memory seats/power mirrors/adjustable pedals (if equipped) This system allows automatic positioning of the driver seat, power mirrors, and adjustable pedals to two programmable positions.
The head restraints can be moved up by pulling up on the head restraint. Push release button to lower head restraint. Split-folding rear seat One or both rear seatbacks can be folded down to provide additional cargo space.
Before returning the seatback to its original position, make sure that cargo or any objects are not trapped behind the seatback. After returning the seatback to its original position, pull on the seatback to ensure that it has fully latched. An unlatched seat may become dangerous in the event of a sudden stop or collision.
• Driver’ s seat position sensor . • Passenger occupant classification sensor • Front crash severity sensor . • Restraints Control Module (RCM) with impact and safing sensors.
levels of crash severity and modify the deployment strategy of the dual-stage airbags and safety belt pretensioners. Driver ’s seat position sensor The driver’ s seat position sensor allows your Personal Safety System 娂 to tailor the deployment level of the driver dual-stage airbag based on seat position.
allows your Personal Safety System 娂 to tailor the airbag deployment and safety belt pretensioner activation depending upon safety belt usage. Refer to Safety belt section in this chapter .
Safety belt precautions Always drive and ride with your seatback upright and the lap belt snug and low across the hips. T o reduce the risk of injury , make sure children sit where they can be properly restrained. Never let a passenger hold a child on his or her lap while the vehicle is moving.
Combination lap and shoulder belts 1. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) until you hear a snap and feel it latch. Make sure the tongue is securely fastened in the buckle. 2. T o unfasten, push the release button and remove the tongue from the buckle.
All safety restraints in the vehicle are combination lap and shoulder belts. All of the passenger combination lap and shoulder belts have two types of locking modes described below: V ehicle sensitive.
• Grasp the shoulder portion and pull downward until the entire belt is pulled out. • Allow the belt to retract. As the belt retracts, you will hear a clicking sound.
Position the safety belt height adjusters so that the belt rests across the middle of your shoulder . Failure to adjust the safety belt properly could reduce the effectiveness of the seat belt and increase the risk of injury in a collision.
Both the driver’ s and passenger’ s safety belt usages are monitored and either may activate the BeltMinder 娂 feature. The warnings are the same for the driver and the front passenger .
The following are reasons most often given for not wearing safety belts (All statistics based on U.S. data): Reasons given... Consider ... “Crashes are rare events” 36700 crashes occur every day . The more we drive, the more we are exposed to “rare” events, even for good drivers.
Do not sit on top of a buckled safety belt to avoid the BeltMinder 娂 chime. Sitting on the safety belt will increase the risk of injury in an accident. T o disable (one-time) or deactivate the BeltMinder 娂 feature please follow the directions stated below .
• Step 3 must be completed within 50 seconds after the safety belt warning light turns off. 3. For the seating position being disabled, at a moderate speed, buckle then unbuckle the safety belt 9 times, ending in the unbuckled state. (Step 3 must be completed within 50 seconds after the safety belt warning light turns off.
hardware, should be inspected after a collision. Ford Motor Company recommends that all safety belt assemblies in use in vehicles involved in a collision be replaced. However , if the collision was minor and an authorized dealer finds that the belts do not show damage and continue to operate properly , they do not need to be replaced.
Important supplemental restraint system precautions Airbags DO NOT inflate slowly or gently and the risk of injury from a deploying airbag is greatest close to the trim covering the airbag module.
Do not attempt to service, repair , or modify the airbag supplemental restraint system (SRS) or its fuses. See your authorized dealer . Modifying or adding equipment to the front end of the vehicle (including frame, bumper , front end body structure and tow hooks) may affect the performance of the airbag system, increasing the risk of injury .
How does the airbag supplemental restraint system work? The airbag SRS is designed to activate when the vehicle sustains longitudinal deceleration sufficient to cause the sensors to close an electrical circuit that initiates airbag inflation.
Several air bag system components get hot after inflation. Do not touch them after inflation. If the air bag has deployed, the air bag will not function again and must be replaced immediately . If the air bag is not replaced, the unrepaired area will increase the risk of injury in a collision.
• the system determines that a small child is present in a forward-facing child restraint that is installed according to the manufacturer’ s instructions, • the system determines that a small ch.
• T urn the vehicle off and ask the person to place the seatback in the full upright position. • Have the person sit upright in the seat, centered on the seat cushion, with the person’ s legs comfortably extended. • Restart the vehicle and have the person remain in this position for about two minutes.
passenger seat, the passenger airbag will be disabled. Even though the passenger airbag is disabled, the ⬙ pass airbag off ⬙ lamp may or may not be illuminated according to the table below . Objects Pass Airbag Off Indicator Light Passenger Airbag Small (i.
In case there is a problem with the front passenger sensing system, the airbag readiness lamp in the instrument cluster will stay lit. If the airbag readiness lamp is lit, do the following: The driver and/or adult passengers should check for any objects that may be lodged underneath the front passenger seat or cargo interfering with the seat.
A difficulty with the system is indicated by one or more of the following: • The readiness light (same light for front and side airbag system) will either flash or stay lit. • The readiness light will not illuminate immediately after ignition is turned on.
automotive safety experts known as the Side Airbag T echnical W orking Group. These recommended testing procedures help reduce the risk of injuries related to the deployment of side airbags.
Several air bag system components get hot after inflation. Do not touch them after inflation. If the side airbag has deployed, the airbag will not function again. The side airbag system (including the seat) must be inspected and serviced by an authorized dealer .
All occupants of the vehicle including the driver should always wear their safety belts even when an airbag SRS and Safety Canopy 娂 system is provided. T o reduce risk of injury , do not obstruct or place objects in the deployment path of the inflatable Safety Canopy 娂 .
The Safety Canopy 娂 system, in combination with seat belts, can help reduce the risk of severe injuries in the event of a significant side impact collision or rollover event. Children 12 years old and under should always be properly restrained in the second row seats.
If the Safety Canopy 娂 system has deployed, the Safety Canopy 娂 will not function again unless replaced. The Safety Canopy 娂 system (including the A, B, and C pillar trim) must be inspected and serviced by an authorized dealer . If the Safety Canopy 娂 is not replaced, the unrepaired area will increase the risk of injury in a collision.
must put them in safety seats made especially for children. Many states require that children use approved booster seats until they are eight years old. Check your local and state or provincial laws for specific requirements regarding the safety of children in your vehicle.
bend comfortably . Booster seats also may make the shoulder belt fit better and more comfortably , but make sure that the belt is approximately centered on the shoulder .
• Those with a high back. If, with a backless booster seat, you cannot find a seating position that adequately supports your child’ s head, a high back booster seat would be a better choice. Either type can be used at any seating position equipped with lap/shoulder belts if your child is over 40 lb.
Move a child to a different seating location if the shoulder belt does not stay positioned on the shoulder during use. Follow all instructions provided by the manufacturer of the booster seat.
• Place seat back in upright position. • Put the safety belt in the automatic locking mode. Refer to Automatic locking mode. • LA TCH lower anchors are recommended for use by children up to 48 lb (22 kg) in a child restraint.
1. Position the child safety seat in a seat with a combination lap and shoulder belt. 2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together . 3. While holding the shoulder and lap belt portions together , route the tongue through the child seat according to the child seat manufacturer’ s instructions.
4. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) for that seating position until you hear a snap and feel the latch engage.
8. Allow the safety belt to retract to remove any slack in the belt. 9. Before placing the child in the seat, forcibly move the seat forward and back to make sure the seat is securely held in place. T o check this, grab the seat at the belt path and attempt to move it side to side and forward.
2. Route the child safety seat tether strap over the back of the seat. For vehicles with adjustable head restraints, route the tether strap under the head restraint and between the head restraint posts, otherwise route the tether strap over the top of the seatback.
Attaching safety seats with LA TCH (Lower Anchors and T ethers for Children) attachments for child seat anchors Some child safety seats have two rigid or webbing mounted attachments that connect to two anchors at certain seating positions in your vehicle.
Attach LA TCH lower attachments of the child seat only to the anchors shown. If you install a child seat with rigid LA TCH attachments, do not tighten the tether strap enough to lift the child seat off the vehicle seat cushion when the child is seated in it.
INFORMA TION ABOUT UNIFORM TIRE QUALITY GRADING New vehicles are fitted with tires that have a rating on them called T ire Quality Grades. The Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width.
The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics.
Increasing the inflation pressure beyond this pressure will not increase the tire’ s load carrying capability . • kPa: Kilopascal, a metric unit of air pressure.
gauges may be inaccurate. Ford Motor Company recommends the use of a digital or dial-type tire pressure gauge rather than a stick-type tire pressure gauge. Use the recommended cold inflation pressure for optimum tire performance and wear . Under -inflation or over -inflation may cause uneven treadwear patterns.
T o check the pressure in your tire(s): 1. Make sure the tires are cool, meaning they are not hot from driving even a mile. Note: If you have to drive a distance to get air for your tire(s), check and record the tire pressure first and add the appropriate air pressure when you get to the pump.
internal damage to the tire is suspected, have the tire demounted and inspected in case it needs to be repaired or replaced. For your safety , tires that are damaged or show signs of excessive wear should not be used because they are more likely to blow out or fail.
U.S. DOT T ire Identification Number (TIN): This begins with the letters “DOT” and indicates that the tire meets all federal standards. The next two numbers or letters are the plant code designating where it was manufactured, the next two are the tire size code and the last four numbers represent the week and year the tire was built.
Tire and wheel alignment A bad jolt from hitting a curb or pothole can cause the front end of your vehicle to become misaligned or cause damage to your tires. If your vehicle seems to pull to one side when you’re driving, the wheels may be out of alignment.
• Rear Wheel Drive (RWD) vehicles/Four Wheel Drive (4WD)/ All Wheel Drive (A WD) vehicles (front tires at top of diagram) Sometimes irregular tire wear can be corrected by rotating the tires.
Only use replacement tires and wheels that are the same size and type (such as P-metric versus L T -metric or all-season versus all-terrain) as those originally provided by Ford.
2. 215: Indicates the nominal width of the tire in millimeters from sidewall edge to sidewall edge. In general, the larger the number , the wider the tire. 3. 65: Indicates the aspect ratio which gives the tire’ s ratio of height to width. 4. R: Indicates a “radial” type tire.
Letter rating Speed rating - mph (km/h) Y 186 mph (299 km/h) Note: For tires with a maximum speed capability over 149 mph (240 km/h), tire manufacturers sometimes use the letters ZR. For those with a maximum speed capability over 186 mph (299 km/h), tire manufacturers always use the letters ZR.
• T emperature: The temperature grades are A (the highest), B and C, representing the tire’ s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel.
Information on “T” type tires “T” type tires have some additional information beyond those of “P” type tires; these differences are described below: T145/80D16 is an example of a tire size. Note: The temporary tire size for your vehicle may be different from this example.
The tires on your vehicle have all weather treads to provide traction in rain and snow . However , in some climates, you may need to use snow tires and chains. Follow these guidelines when using snow tires and chains: • Use only SAE class “S” cables or equivalent on the front axle for P215/60R17 equipped vehicles.
V ehicle Curb W eight – is the weight of your new vehicle when you picked it up from your authorized dealer plus any aftermarket equipment. Payload – is the combined weight of cargo and passengers that the vehicle is carrying.
Example only: Cargo W eight – includes all weight added to the Base Curb W eight, including cargo and optional equipment. When towing, trailer tongue load or king pin weight is also part of cargo weight.
GA W (Gross Axle W eight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload. GA WR (Gross Axle W eight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear).
GVWR (Gross V ehicle W eight Rating) – is the maximum allowable weight of the fully loaded vehicle (including all options, equipment, passengers and cargo). The GVWR is shown on the Safety Compliance Certification Label located on the B-Pillar or the edge of the driver’ s door .
mandatory options, no cargo (internal or external), a tongue load of 10–15% (conventional trailer) or king pin weight of 15–25% (fifth wheel trailer), and driver only (150 lb. [68 kg]). Consult your authorized dealer (or the RV and T railer T owing Guide provided by your authorized dealer) for more detailed information.
capacity to carry you, 4 of your friends and all the golf bags? Y ou and four friends average 220 lb. (99 kg) each and the golf bags weigh approximately 30 lb. (13.5 kg) each. The calculation would be: 1400 – (5 x 220) – (5 x 30) = 1400 – 1100 – 150 = 150 lb.
T owing trailers beyond the maximum recommended gross trailer weight exceeds the limit of the vehicle and could result in engine damage, transmission damage, structural damage, loss of vehicle control, vehicle rollover and personal injury .
authorized dealer or trailer rental agency for proper instructions and equipment for hooking up trailer lamps. Driving while you tow When towing a trailer: • T urn off the speed control. The speed control may shut off automatically when you are towing on long, steep grades.
In case of roadside emergency with a disabled vehicle, please refer to the Wrecker towing section in the Driving chapter . These guidelines are designed to ensure that your transmission is not damaged due to insufficient lubrication.
STARTING Positions of the ignition 1. LOCK, locks the automatic transaxle gearshift lever and allows key removal. This position also shuts the engine and all electrical accessories off without locking the steering wheel. T o lock the steering wheel, remove the key then turn the steering wheel.
Do not park, idle, or drive your vehicle in dry grass or other dry ground cover . The emission system heats up the engine compartment and exhaust system, which can start a fire. Do not start your vehicle in a closed garage or in other enclosed areas. Exhaust fumes can be toxic.
• Make sure the gearshift lever is in P (Park). 3. T urn the key to 3 (RUN) without turning the key to 4 (ST ART). Some warning lights will briefly illuminate. See W arning lights and chimes in the Instrument Cluster chapter for more information regarding the warning lights.
Guarding against exhaust fumes Carbon monoxide is present in exhaust fumes. T ake precautions to avoid its dangerous effects. If you smell exhaust fumes inside your vehicle, have your dealer inspect your vehicle immediately . Do not drive if you smell exhaust fumes.
keeping the brakes from locking. Noise from the ABS pump motor and brake pedal pulsation may be observed during ABS braking and the brake pedal may suddenly travel a little farther as soon as ABS braking is done and normal brake operation resumes. These are normal characteristics of the ABS and should be no reason for concern.
The BRAKE warning lamp in the instrument cluster illuminates and remains illuminated (when the ignition is turned ON) until the parking brake is released. Always set the parking brake fully and make sure that the gearshift is securely latched in P (Park).
The T raction Control 娂 system will allow your vehicle to make better use of available traction on slippery surfaces. The system is a driver aid which makes your vehicle easier to handle primarily on snow and ice covered roads. During T raction Control 娂 operation the engine will not “rev-up” when you push further on the accelerator .
If the power steering system breaks down (or if the engine is turned off), you can steer the vehicle manually , but it takes more effort. If the steering wanders or pulls, check for: • an improperly.
3. Locate the white plastic cover at the front driver side of the gearshift lever . Locate the screw which attaches this cover and remove using a screwdriver . Remove the cover by tilting forward while pulling up and out of the gearshift assembly . 4.
decreasing engine RPM which causes a slight energy loss as the gears change. The gear changes can be felt by the driver . W ith the CVT , there is no energy transfer loss from shifting because there is no gear shifting up or down. Acceleration up to vehicle operating speed is smooth and continuous; uninterrupted by gear shifting.
R (Reverse) W ith the gearshift lever in R (Reverse), the vehicle will move backward. Always come to a complete stop before shifting into and out of R (Reverse). N (Neutral) W ith the gearshift lever in N (Neutral), the vehicle can be started and is free to roll.
• Move the gearshift lever and securely latch it in P (Park) Always set the parking brake fully and make sure the gearshift is latched in P (Park). T urn the ignition to the LOCK position and remove the key whenever you leave your vehicle. R (Reverse) W ith the gearshift lever in R (Reverse), the vehicle will move backward.
This system is not designed to prevent contact with small or moving objects. The system is designed to provide a warning to assist the driver in detecting large stationary objects to avoid damaging the vehicle. The system may not detect smaller objects, particularly those close to the ground.
indicator light on the control will illuminate when the system is turned off. If the indicator light illuminates when the RSS is not turned off, it may indicate a failure in the RSS. Keep the RSS sensors (located on the rear bumper/fascia) free from snow , ice and large accumulations of dirt (do not clean the sensors with sharp objects).
Basic operating principles • Drive slower in strong crosswinds which can affect the normal steering characteristics of your vehicle. • Be extremely careful when driving on pavement made slippery by loose sand, water , gravel, snow or ice.
If the parking brake is fully released, but the brake warning lamp remains illuminated, the brakes may not be working properly . See your authorized dealer . Do not spin the wheels at over 35 mph (56 km/h). The tires may fail and injure a passenger or bystander .
gear and drive steadily through the terrain. Apply the accelerator slowly and avoid spinning the wheels. If your vehicle is equipped with a 6–speed transmission: When driving at slow speeds in deep sand under high outside temperatures, use L (Low) gear when possible.
“T read Lightly” is an educational program designed to increase public awareness of land-use regulations and responsibilities in our nations wilderness areas.
Driving on snow and ice Note: Excessive tire slippage can cause transaxle damage. A WD vehicles have advantages over 2WD vehicles in snow and ice but can skid like any other vehicle. Should you start to slide while driving on snowy or icy roads, turn the steering wheel in the direction of the slide until you regain control.
DRIVING THROUGH WATER If driving through deep or standing water is unavoidable, proceed very slowly especially when the depth is not known. Never drive through water that is higher than the bottom of the wheel rims (for cars) or the bottom of the hubs (for trucks).
ROADSIDE ASSISTANCE Getting roadside assistance T o fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program.
U.S. Ford or Mercury vehicle customers who require roadside assistance, call 1–800–241–3673; Lincoln vehicle customers call 1–800–521–4140. Canadian customers who require roadside assistance, call 1–800–665–2006. If you need to arrange roadside assistance for yourself, Ford Motor Company will reimburse a reasonable amount.
The fuel pump shut-off switch is located in the front passenger footwell area in the right upper corner . T o reset the switch: 1. T urn the ignition OFF . 2. Check the fuel system for leaks. 3. If no leaks are apparent, reset the switch by pushing in on the reset button.
Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 5A T an T an — — — 7.
The fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description F1 20A High beams F2 15A Interior lamps (Courtesy and demand lamps), Delayed accessory .
Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description F17 30A Rear defroster F18 10A PCM relay coil, Shifter Brake-Shift Interlock (BSI), Passive Anti-Theft System (P A TS) .
If the battery has been disconnected and reconnected, refer to the Battery section of the Maintenance and Specifications chapter . The high-current fuses are coded as follows: Fuse/Relay Location Fuse.
Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 13 — Not used 14 — Not used 15 15A** T raction Control Module (TCM) 16 20A** Power point (Console) 17 10A** Alternator 18 40A.
Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 40 1A Diode A/C clutch 41 1 ⁄ 2 ISO relay Fog lamps 42 — Not used 43 1 ⁄ 2 ISO relay A/C clutch 44 1 ⁄ 2 ISO relay Fuel p.
The use of tire sealants is not recommended and may damage your tires. Dissimilar spare tire/wheel information Failure to follow these guidelines could result in an increased risk of loss of vehicle control, injury or death. If you have a dissimilar spare tire/wheel, then it is intended for temporary use only .
• Ground clearance and parking at curbs • W inter weather driving capability • W et weather driving capability For vehicles equipped with 4WD, it is not recommended that the vehicle be operated in 4WD modes with a temporary emergency spare tire.
Removing the spare tire and jack 1. Lift the trunk cargo cover , and remove the wing nut that secures the spare tire by turning it counterclockwise. 2. Lift and remove the spare tire from the trunk. 3. Remove the second wing nut that secures the jack retention bracket by turning it counterclockwise, remove the jack kit from the vehicle.
T o help prevent the vehicle from moving when you change a tire, be sure to place the transaxle in P (Park), set the parking brake and block (in both directions) the wheel that is diagonally opposite (other side and end of the vehicle) to the tire being changed.
4. Put the jack in the jack notch next to the tire you are changing. T urn the jack handle clockwise until the wheel is completely off the ground. 5. Remove the lug nuts with the lug wrench. 6. Replace the flat tire with the spare tire, making sure the valve stem is facing outward.
Stowing the tire and jack 1. Fully collapse the jack, fold the lug wrench socket into the handle and place the jack and wrench into the felt bag as shown. T ake care to position the jack as shown to ensure that the locating holes in the jack base can be placed on the locating tabs of the jack mounting bracket in the spare tire tub.
If you are stowing the temporary spare tire, place the tire over the jack and secure it with the large wing nut. WHEEL LUG NUT TORQUE SPECIFICATIONS Retighten the lug nuts to the specified torque at 100 miles (160 km) after any wheel disturbance (tire rotation, changing a flat tire, wheel removal, etc.
Do not attempt to push-start your vehicle. Automatic transmissions do not have push-start capability; doing so may damage the catalytic converter . Preparing your vehicle When the battery is disconnected or a new battery is installed, the transmission must relearn its shift strategy .
2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery . 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery .
4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’ s engine, away from the battery and the carburetor/fuel injection system. Do not use fuel lines, engine rocker covers or the intake manifold as grounding points.
Removing the jumper cables Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the ground metal surface. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery .
3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’ s battery . 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’ s battery .
WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or , if you are a member of a roadside assistance program, your roadside assistance service provider . It is recommended that your vehicle be towed with a wheel lift or flatbed equipment.
In case of a roadside emergency with a disabled vehicle (without access to wheel dollies, flatbed transport vehicle or a car hauling trailer) your vehicle can be flat towed (all wheels on the ground) only under the following conditions: • The ambient temperature is above 32°F (0°C) • Place the automatic transaxle in N (Neutral).
GETTING THE SERVICES YOU NEED At home Y ou must take your Ford vehicle to an authorized dealer for warranty repairs. While any authorized dealer handling your vehicle line will provide warranty service, we recommend you return to your selling authorized dealer who wants to ensure your continued satisfaction.
In Canada: Customer Relationship Centre Ford Motor Company of Canada, Limited P .O. Box 2000 Oakville, Ontario L6J 5E4 1-800-565-3673 (FORD) www .ford.
In some states (in the U.S.) you must directly notify Ford in writing before pursuing remedies under your state’ s warranty laws. Ford is also allowed a final repair attempt in some states.
THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM (U.S. ONLY) Y our satisfaction is important to Ford Motor Company and to your dealer . Experience has shown that our customers have been very successful in achieving satisfaction by following the three-step procedure outlined on the front page of the W arranty Guide.
authorized dealer to resolve a factory-related vehicle service concern have been unsatisfactory , Ford of Canada participates in an impartial third party mediation/arbitration program administered by the Canadian Motor V ehicle Arbitration Plan (CAMV AP).
GETTING ASSIST ANCE OUTSIDE THE U.S. AND CANADA Before exporting your vehicle to a foreign country , contact the appropriate foreign embassy or consulate. These officials can inform you of local vehicle registration regulations and where to find unleaded fuel.
For a free publication catalog, order toll free: 1-800-782-4356 Monday-Friday 8:00 a.m. - 6:00 p.m. EST Helm, Incorporated can also be reached by their website: www .helminc.com. (Items in this catalog may be purchased by credit card, check or money order .
W ASHING THE EXTERIOR W ash your vehicle regularly with cool or lukewarm water and a neutral pH shampoo, such as Motorcraft Detail W ash (ZC-3–A), which is available from your authorized dealer . • Never use strong household detergents or soap, such as dish washing or laundry liquid.
• Remove particles such as bird droppings, tree sap, insect deposits, tar spots, road salt and industrial fallout before repairing paint chips. • Always read the instructions before using the products. ALUMINUM WHEELS AND WHEEL COVERS Aluminum wheels and wheel covers are coated with a clearcoat paint finish.
• 3.0L Duratec engine • Never wash or rinse the engine while it is running; water in the running engine may cause internal damage. PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products are available from your authorized dealer .
• The wiper blades can be cleaned with isopropyl (rubbing) alcohol or Motorcraft Premium W indshield W asher Concentrate (ZC-32–A), available from your authorized dealer .
• Remove light stains and soil with Motorcraft Professional Strength Carpet & Upholstery Cleaner (ZC-54). • If grease or tar is present on the material, spot-clean the area first with Motorcraft Spot and Stain Remover (ZC-14).
quality products have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and appearance of your vehicle. Each product is made from high quality materials that meet or exceed rigid specifications.
SERVICE RECOMMENDATIONS T o help you service your vehicle: • W e highlight do-it-yourself items in the engine compartment for easy location. • W e provide scheduled maintenance information which makes tracking routine service easy .
OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the bottom of the instrument panel near the steering column. 2. Go to the front of the vehicle and release the auxiliary latch that is located under the front center of the hood.
IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 3.0L DOHC V6 DURATEC ENGINE 1. Engine coolant reservoir 2. Power steering fluid reservoir 3. Engine coolant bleed plug 4. Brake fluid reservoir 5. Battery 6. Power distribution box 7. Air filter assembly 8.
WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if the level is low . In very cold weather , do not fill the reservoir completely . Only use a washer fluid that meets Ford specification WSB-M8B16–A2. Do not use any special washer fluid such as windshield water repellent type fluid or bug wash.
T o prolong the life of the wiper blades, it is highly recommended to scrape off the ice on the windshield before turning on the wipers. The layer of ice has many sharp edges and can damage the micro edge of the wiper rubber element.
• If the oil level is within this range, the oil level is acceptable. DO NOT ADD OIL. • If the oil level is below this mark, engine oil must be added to raise the level within the normal operating range. • If required, add engine oil to the engine.
4. Install the indicator and ensure it is fully seated. 5. Fully install the engine oil filler cap by turning the filler cap clockwise until it stops. T o avoid possible oil loss, DO NOT operate the vehicle with the engine oil level indicator and/or the engine oil filler cap removed.
BATTERY Y our vehicle is equipped with a Motorcraft maintenance-free battery which normally does not require additional water during its life of service. However , for severe usage or in high temperature climates, check the battery electrolyte level. Refer to scheduled maintenance information for the service interval schedules.
When lifting a plastic-cased battery , excessive pressure on the end walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery . Lift the battery with a battery carrier or with your hands on opposite corners.
• Always dispose of automotive batteries in a responsible manner . Follow your local authorized standards for disposal. Call your local authorized recycling center to find out more about recycling automotive batteries.
When the engine is cold, check the level of the engine coolant in the reservoir . • The engine coolant should be at the “FULL COLD” level or within the “COLD FILL RANGE” as listed on the engine coolant reservoir (depending upon application).
Do not add engine coolant when the engine is hot. Steam and scalding liquids released from a hot cooling system can burn you badly . Also, you can be burned if you spill coolant on hot engine parts. Do not put engine coolant in the windshield washer fluid container .
1. Before you begin, turn the engine off and let it cool. 2. When the engine is cool, wrap a thick cloth around the coolant pressure relief cap on the coolant reservoir (an opaque plastic bottle). Slowly turn cap counterclockwise (left) until pressure begins to release.
8. Add coolant/water mixture through the thermostat housing opening until full at housing opening. 9. Install the thermostat housing bleed plug. Install metal pin by pushing into the slot. After any coolant has been added, check the coolant concentration, refer to Checking engine coolant section.
If you have to add more than 1.0 quart (1.0 liter) of engine coolant per month, have your authorized dealer check the engine cooling system. Y our cooling system may have a leak. Operating an engine with a low level of coolant can result in engine overheating and possible engine damage.
• Decreased engine coolant concentrations below 40% will decrease the freeze protection characteristics of the engine coolant and may cause engine damage. • Refer to the chart on the coolant container to ensure the coolant concentration in your vehicle will provide adequate protection at the temperatures in which you drive.
Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materials and any open flames before refueling your vehicle. • Always turn off the vehicle before refueling. • Automotive fuels can be harmful or fatal if swallowed.
Refueling Fuel vapor burns violently and a fuel fire can cause severe injuries. T o help avoid injuries to you and others: • Read and follow all the instructions on the pump island; • T urn off yo.
If you must replace the fuel filler cap, replace it with a fuel filler cap that is designed for your vehicle. The customer warranty may be void for any damage to the fuel tank or fuel system if the correct genuine Ford or Motorcraft fuel filler cap is not used.
Octane recommendations Y our vehicle is designed to use “Regular” unleaded gasoline with pump (R+M)/2 octane rating of 87. W e do not recommend the use of gasolines labeled as “Regular” that are sold with octane ratings of 86 or lower in high altitude areas.
• The indicator may come on. For more information on the “Check Engine” or the “Service engine soon” indicator , refer to W arning lights and chimes in the Instrument Cluster chapter . ESSENTIALS OF GOOD FUEL ECONOMY Measuring techniques Y our best source of information about actual fuel economy is you, the driver .
• Have the vehicle loading and distribution the same every time. Y our results will be most accurate if your filling method is consistent. Calculating fuel economy 1. Fill the fuel tank completely and record the initial odometer reading (in miles or kilometers).
• Revving the engine before turning it off may reduce fuel economy . • Using the air conditioner or defroster may reduce fuel economy . • Y ou may want to turn off the speed control in hilly terrain if unnecessary shifting between third and fourth gear occurs.
• Close windows for high speed driving. EP A window sticker Every new vehicle should have the EP A window sticker . Contact your authorized dealer if the window sticker is not supplied with your vehicle. The EP A window sticker should be your guide for the fuel economy comparisons with other vehicles.
Exhaust leaks may result in entry of harmful and potentially lethal fumes into the passenger compartment. Do not make any unauthorized changes to your vehicle or engine.
the description in the W arning lights and chimes section of the Instrument Cluster chapter . Y our vehicle may not pass the I/M test with the indicator on. If the vehicle’ s powertrain system or its battery has just been serviced, the on-board diagnostics system is reset to a “not ready for I/M test” condition.
BRAKE FLUID The fluid level will drop slowly as the brakes wear , and will rise when the brake components are replaced. Fluid levels between the “MIN” and “MAX” lines are within the normal operating range; there is no need to add fluid.
If your transaxle does not engage normally , do not attempt to drive. The vehicle should be towed to your authorized dealer for evaluation. Checking 6–speed automatic transmission fluid (if equipped) Refer to your scheduled maintenance information for scheduled intervals for fluid checks and changes.
Checking automatic transmission fluid at cool temperature (32°F-81°F [17°C-27°C]) If a fluid check is necessary at a low fluid temperature (32°F-81°F [17°C-27°C]), perform the check using the cold range on the dipstick. However , the fluid must be re-checked at the proper fluid temperature.
If an overfill occurs, excess fluid should be removed by an authorized dealer . An overfill condition of transmission fluid may cause shift and/or engagement concerns and/or possible damage. Do not use supplemental transmission fluid additives, treatments or cleaning agents.
REFILL CAPACITIES Fluid Ford Part Name Application Capacity Brake fluid Motorcraft High Performance DOT 3 Motor V ehicle Brake Fluid All Between MAX and MIN on reservoir Engine coolant 1 Motorcraft Premium Gold Engine Coolant (yellow-colored) 3.0L engine 11.
Fluid Ford Part Name Application Capacity Automatic transaxle Motorcraft Continuously V ariable Chain T ype T ransmission Fluid 3 CVT automatic transaxle 10.0 quarts (9.5L) 4 Premium Automatic T ransmission Fluid 3 6–speed automatic transaxle 7.4 quarts (7.
4 Approximate dry fill capacity . Actual amount may vary during fluid changes. LUBRICANT SPECIFICATIONS Items Ford Part Name or equivalent Ford Part Number Ford Specification Brake fluid Motorcraft Hi.
Items Ford Part Name or equivalent Ford Part Number Ford Specification Coupler fluid V olvo T ransmission Oil, Clutch 1161641 — Power T ransfer Unit Motorcraft SAE 75W -90 Fuel Efficient High Perfor.
ENGINE DATA Engine 3.0L-DOHC V6 engine Displacement 183 cubic inches Required fuel 87 octane Firing order 1–4–2–5–3–6 Spark plug gap (0.052–0.056 inch) 1.32–1.42 mm Ignition system Coil on plug Compression ratio 10.0:1 ENGINE DRIVEBELT ROUTING • 3.
5 2 3 2006 Five Hundred (500) Owners Guide (post-2002-fmt) USA (fus) Maintenance and Specifications 261.
IDENTIFYING YOUR VEHICLE Certification label The National Highway T raffic Safety Administration Regulations require that a Safety Compliance Certification Label be affixed to a vehicle and prescribe where the Safety Compliance Certification Label may be located.
The V ehicle Identification Number (VIN) contains the following information: 1. W orld manufacturer identifier 2. Brake type and Gross V ehicle W eight Rating (GVWR) 3. V ehicle line, series, body type 4. Engine type 5. Check digit 6. Model year 7. Assembly plant 8.
GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for your vehicle through your local authorized Ford or Ford of Canada dealer .
Interior style Electrochromic compass/temperature/Homelink options Floor mats Scuff plates Lifestyle Engine block heaters Interior cargo organization and management Smoker’ s pack Peace of mind Firs.
• T o avoid interference with other vehicle functions, such as anti-lock braking systems, amateur radio users who install radios and antennas onto their vehicle should not locate the Amateur Radio Antennas in the area of the driver’ s side hood.
A Accessory delay .......................... 63 Air cleaner filter ....................... 255 Air conditioning ....................42, 44 Airbag supplemental restraint system ................120–121, 129, 131 and child safety seats ............ 122 description .
waxing ..................................... 220 wheels ...................................... 221 wiper blades ............................ 222 Climate control (see Air conditioning or Heating) ......42, 44 Clock .....................................
specifications .................. 258, 260 Exhaust fumes .......................... 173 F Fluid capacities ......................... 256 Foglamps ..................................... 49 Four -Wheel Drive vehicles driving off road ....................
K Keyless entry system ................. 92 autolock ..................................... 94 Keys positions of the ignition ......... 170 L Lamps autolamp system ....................... 48 bulb replacement specifications chart .................. 52 daytime running light .
Relays ........................................ 192 Remote entry system ................. 87 illuminated entry ................ 91–92 opening the trunk ..................... 88 Reverse sensing system ........... 181 Roadside assistance .............
T ransaxle fluid, checking and adding (automatic) ..................... 252–253 fluid, refill capacities .............. 256 lubricant specifications .......... 260 T ransmission ............................. 177 brake-shift interlock (BSI) .... 177 lubricant specifications .
Een belangrijk punt na aankoop van elk apparaat Ford 2006 Five Hundred (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Ford 2006 Five Hundred heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Ford 2006 Five Hundred vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Ford 2006 Five Hundred leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Ford 2006 Five Hundred krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Ford 2006 Five Hundred bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Ford 2006 Five Hundred kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Ford 2006 Five Hundred . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
