Gebruiksaanwijzing /service van het product 2006 Freestar van de fabrikant Ford
Ga naar pagina of 320
Introduction 4 Instrument Cluster 10 W arning and control lights 10 Gauges 15 Entertainment Systems 18 AM/FM stereo 18 AM/FM stereo with CD 20 AM/FM stereo cassette with CD 23 AM/FM stereo with in-das.
Seating and Safety Restraints 109 Seating 109 Safety restraints 134 Airbags 148 Child restraints 162 Tires, Wheels and Loading 180 T ire Information 180 T ire Inflation 182 T ire Pressure Monitoring S.
Maintenance and Specifications 270 Engine compartment 272 Engine oil 274 Battery 277 Engine Coolant 280 Fuel information 285 Air filter(s) 302 Part numbers 302 Refill capacities 303 Lubricant specifications 304 Accessories 310 Index 312 All rights reserved.
CALIFORNIA Proposition 65 W arning W ARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
SAFETY AND ENVIRONMENT PROTECTION W arning symbols in this guide How can you reduce the risk of personal injury to yourself or others? In this guide, answers to such questions are contained in comments highlighted by the warning triangle symbol. These comments should be read and observed.
SPECIAL NOTICES New V ehicle Limited W arranty For a detailed description of what is covered and what is not covered by your vehicle’ s New V ehicle Limited W arranty , refer to the Warranty Guide that is provided to you along with your Owner’ s Guide.
T o access this information, special equipment must be directly connected to the recording modules. Ford Motor Company and Ford of Canada do not access event data recorder information without obtainin.
These are some of the symbols you may see on your vehicle. V ehicle Symbol Glossary Safety Alert See Owner’ s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat Child Seat Installation.
V ehicle Symbol Glossary Power W indows Front/Rear Power W indow Lockout Child Safety Door Lock/Unlock Interior Luggage Compartment Release Symbol Panic Alarm Engine Oil Engine Coolant Engine Coolant .
W ARNING LIGHTS AND CHIMES Standard instrument cluster Optional instrument cluster W arning lights and gauges can alert you to a vehicle condition that may become serious enough to cause extensive repairs. A warning light may illuminate when a problem exists with one of your vehicle’ s functions.
bulb works. If any light remains on after starting the vehicle, refer to the respective system warning light for additional information. Check engine: The Check Engine indicator light illuminates when the ignition is first turned to the ON position to check the bulb.
Anti-lock brake system: If the ABS light stays illuminated or continues to flash, a malfunction has been detected, have the system serviced immediately by your authorized dealer . Normal braking is still functional unless the brake warning light also is illuminated.
T raction Control 娂 or AdvanceT rac 威 active (if equipped): Illuminates when the T raction Control 娂 is active, refer to the Driving chapter for more information. Low tire pressure warning: Illuminates when your tire pressure is low . If the light remains ON at start up or while driving, the tire pressure should be checked.
Low washer fluid: Illuminates when the windshield washer fluid is low . • W ithout Message Center • W ith Message Center Door ajar: Illuminates when the ignition is in the ON position and any door is open. • W ithout Message Center • W ith Message Center Displays which door or the liftgate is open.
High beams: Illuminates when the high beam headlamps are turned on. Key-in-ignition warning chime: Sounds when the key is left in the ignition in the OFF/LOCK or ACCESSORY position and the driver’ s door is opened.
Engine coolant temperature gauge: Indicates engine coolant temperature. At normal operating temperature, the needle will be in the normal range (between “H” and “C”). If it enters the red section, the engine is overheating. Stop the vehicle as soon as safely possible, switch off the engine and let the engine cool.
• W ith Message Center T o reset, press and hold the message center RESET button for three seconds to reset. T achometer: Indicates the engine speed in revolutions per minute. Driving with your tachometer pointer continuously at the top of the scale may damage the engine.
AUDIO SYSTEMS AM/FM stereo system (if equipped) 1. / T uner: Press to manually go up or down the radio frequency . Also use in menu mode to select various settings. 2. Audio: Press to access select various settings. T reble: Press to adjust the treble setting.
3. Seek: Press to access the next/previous strong station or track. 4. Memory presets: T o set a station: Select frequency band AM/FM; tune to a station, press and hold a preset button until sound returns. 5. AM/FM: Press to select AM/FM frequency band.
AM/FM stereo/ single CD sound system (if equipped) 1. / T uner: Press to manually go up or down the radio frequency . Also use in menu mode to select various settings. 2. Phone/mute: Press to mute the playing media. Press again to return to the playing media.
T reble: Press to adjust the treble setting. Use / / SEEK . Balance: Press to adjust the audio between the left and right speakers. Use / / SEEK . Fade: Press to adjust the audio between the front and rear speakers.
10. Fast forward: Press to manually advance in a CD track. 11. Rewind: Press to manually reverse in a CD track. 12. Memory presets: T o set a station: Select frequency band AM/FM; tune to a station, press and hold a preset button until sound returns. 13.
AM/FM stereo cassette/single CD sound system (if equipped) 1. / T uner: Press to manually go up or down the radio frequency . Also use in menu mode to select various settings. 2. Seek: Press to access the next strong station or track. 3. Phone/mute: Press to mute the playing media.
Fade: Press to adjust the audio between the front and rear speakers. Use / / SEEK . Speed sensitive volume (if equipped): Radio volume automatically changes slightly with vehicle speed to compensate for road and wind noise. Press MENU to access and use / / SEEK to adjust.
10. Repeat: Press to repeat the current CD track. 11. Fast forward: Press to manually advance in a CD track or cassette. 12. Rewind: Press to manually reverse in a CD track or cassette. 13. Memory presets: T o set a station: Select frequency band AM/FM; tune to a station, press and hold a preset button until sound returns.
20. CD slot: Insert a CD label side up. 21. Seek: Press to access the previous strong station or track. 22. Scan: Press for a brief sampling of radio stations or CD tracks. Press again to stop. When this radio is used in cargo vans where no rear speakers are installed in the vehicle, fading to the rear speakers will result in no audio output.
3. Menu: Press to toggle through the following modes: T reble: Press to adjust the treble setting. Use / / SEEK . Bass: Press to adjust the bass setting. Use / / SEEK . Balance: Press to adjust the audio between the left and right speakers. Use / / SEEK .
6. T ext: In CD mode, press to display the track name, artist name and disc name (if available). 7. Shuffle: Press to play tracks in random order . 8. Comp (Compression): In CD mode, brings soft and loud CD passages together for a more consistent listening level.
17. CD: Press to enter CD mode. If a CD is already loaded into the system, CD play will begin where it ended last. 18. LOAD: Press to load a CD, then select a slot number using the radio presets 1 through 6. If you don’t select a slot within 5 seconds, the radio shall choose the first available slot for you.
5. SEEK: Press / to access the next/previous strong radio station, cassette selection or CD track. When the rear seat controls are activated, rear seat passengers can use the controls to change the playing media for all passengers (Single Play mode). In this mode, all speakers will play audio from the same media source for all passengers to hear .
W ireless headphones will not play audio from any other sources (AM, FM, tape, or Radio CD). The front and rear seat passengers cannot listen to two different radio stations at the same time.
CD/CD player care Do: • Handle discs by their edges only . Never touch the playing surface. • Inspect discs before playing. Clean only with an approved CD cleaner and wipe from the center out. Don’t: • Expose discs to direct sunlight or heat sources for extended periods of time.
MANUAL HEATING AND AIR CONDITIONING SYSTEM (IF EQUIPPED) 1. T emperature selection: Controls the temperature of the airflow in the vehicle. 2. Air flow selections: Controls the direction of the airflow in the vehicle. See the following for a brief description on each control.
Dual zone manual heating and air conditioning system with rear passenger compartment climate control (if equipped) 1. Air flow selections: Controls the direction of the airflow in the vehicle. See the following for a brief description on each control.
will be warmer or cooler than the driver airflow temperature setting when more than one rear temperature light ( REAR )i s illuminated. 5. R Rear defroster: Press to activate/deactivate rear window defroster . Refer to Rear window defroster later in this chapter for more information.
In the and modes: • Move the temperature control selector to the coldest setting. • Select A/C and recirculated air . Use with A/C to provide colder airflow . • Set the fan to the highest speed initially , then adjust to maintain passenger comfort.
DUAL ZONE AUTOMATIC TEMPERATURE CONTROL WITH REAR PASSENGER COMPARTMENT CLIMATE CONTROL (IF EQUIPPED) 1. Defrost: Distributes outside air through the windshield defroster vents.
engaged manually in any airflow selection except . Recirculated air may turn off automatically in all airflow selections. 7. A/C: Press to activate/deactivate air conditioning. Use with recirculated air to improve cooling performance and efficiency . Engages automatically in AUTO, , and .
Dual zone automatic temperature control with heated seats and rear passenger compartment climate control (if equipped) 1. Defrost: Distributes outside air through the windshield defroster vents. Can be used to clear thin ice or fog from the windshield.
7. : Distributes air through the windshield defroster vents and the floor vents. 8. : Distributes air through the floor vents. 9. : Distributes air through the instrument panel vents and the floor vents. 10. : Distributes air through the instrument panel vents.
19. REAR: Press to enable the control located in the rear seat. Press again to turn the auxiliary system off. Operating tips • T o reduce fog build up on the windshield during humid weather , place the air flow selector in the position.
AUXILIARY CLIMATE CONTROL (IF EQUIPPED) 1. Fan speed: T urn to select the desired fan speed. 2. T emperature/mode selection: The distribution of air from the overhead and floor registers is based on the temperature selected. T urn to select for comfort.
HEADLAMP CONTROL T urns the lamps off. T urns on the parking lamps, instrument panel lamps, license plate lamps and tail lamps. T urns the headlamps on.
T o program the auto lamp exit time delay: 1. Start with the ignition in the OFF position and the headlamp control in the autolamp position. 2. Deselect the auto lamps. 3. Put the ignition in RUN. 4. Put the ignition in OFF . 5. Select the autolamps. • Note: Steps 2 through 5 must be performed within a 10 second period.
Flash to pass Pull toward you slightly to activate and release to deactivate. Battery saver The battery saver will shut off the exterior lamps and interior lamps, except the hazard warning lamps if activated, 10 minutes after the ignition control has been turned off.
• In order to turn off the domelamp, rotate the thumbwheel to the left. The dome lamp will not illuminate if the control switch is in the OFF position.
5. Locate the vertical adjuster on each headlamp, then us ea#2 Phillips screwdriver to turn the adjuster either counterclockwise (to adjust up) or clockwise (to adjust down) positioning the horizontal edge of the high intensity light on the horizontal reference line.
Map lamps (if equipped) The map lamps and controls are located on the center overhead console. Press the raised portion on each lens to activate the lamps. Second row & third row dome and map lamps (if equipped) The second row dome and map lamps are located overhead, above the second row passenger seats.
door is opened. If the control is moved to the driver’ s side position, the lamp will not come on at all. The dome lamp will illuminate whenever a front door is opened. If either front door has been opened from the outside, the lamp will remain on for 20 seconds after the door is shut.
Using the right bulbs Replacement bulbs are specified in the chart below . Headlamp bulbs must be marked with an authorized “D.O.T .” for North America and an “E” for Europe to assure lamp performance, light brightness and pattern and safe visibility .
Replacing headlamp bulbs T o remove the headlamp bulb: 1. Make sure headlamp switch is in the OFF position, then open the hood. 2. Remove the two retainer pins to release the headlamp assembly and pull headlamp assembly forward to expose the back of the bulb.
3. T o remove the side marker bulb, turn the bulb socket counterclockwise, and pull the bulb straight out of the socket. 4. T o remove the parking/turn bulb, turn the socket on the bottom of the headlamp assembly counterclockwise and pull the bulb straight out of the socket.
Replacing license plate lamp bulb The license plate bulbs are located in the license plate housing assembly on the liftgate. T o change the license plate bulbs: 1. Make sure the headlamp switch is in the OFF position. 2. Remove the license lamp screw from the assembly .
MULTI-FUNCTION LEVER W indshield wiper: Rotate the end of the control away from you to increase the speed of the wipers; rotate towards you to decrease the speed of the wipers. W indshield washer: Push the end of the stalk: • briefly: causes a single swipe of the wipers without washer fluid.
TILT STEERING WHEEL T o adjust the steering wheel: 1. Pull and hold the steering wheel release control toward you. 2. Move the steering wheel up or down until you find the desired location. 3. Release the steering wheel release control. This will lock the steering wheel in position.
Conversation mirror The conversation mirror allows the driver to view the rear seating area. This does not replace the rear view mirror . Electronic compass/temperature display (if equipped) The overhead console may have an electronic compass and outside air temperature display .
Zone variation mode 1. Determine which magnetic zone you are in by referring to the zone map. 2. T urn the ignition to the ON position. 3. Press and hold the momentary push-button for approximately 4 seconds, until V AR is displayed, then release it.
Note: Look for a parking lot away from buildings, light posts, manhole covers, sewer and drainage grates and other metallic objects. Some magnetic objects may be hidden underground. Look for signs of underground utilities, water mains or other industrial structures.
Manual door operation when vehicle is stopped or parked on a downhill grade In some cases it may be necessary to have someone hold the door while rear seat passengers are entering or exiting the vehicle. The hold open mechanism will restrain the door open when the vehicle is parked on moderate downhill grades.
The Power Door Lockout Control is located in the overhead console. W ith the control in the OFF position, power operation is disabled from both PSD handles and from both second row passenger switches. The overhead console switch and remote entry transmitter will operate the power doors regardless of the position of the lockout switch.
T o power close the PSD with the inside or outside release handle: • Manually pull the door about 6 inches in the desired direction of travel. The power door assist will take over and complete the open or close operation.
Resetting the PSD The power sliding door may operate incorrectly or not at all because of the following conditions: • a low voltage or dead battery • the door is left opened for more than 6 hours • the battery is disconnected • the PSD Passenger compartment fuse panel fuse (fuse #11) is removed or blown.
T o open the sliding door when the child safety lock is on: • Unlock the sliding door and open the door from the outside. • Press the right or left hand control on the overhead console or the remote to open the door . • The second row passenger switch will still be functional to open the door .
Do not use the power point for operating the cigarette lighter element (if equipped). T o prevent the fuse from being blown, do not use the power point(s) over the vehicle capacity of 12 VDC/180W . T o prevent the battery from being discharged, do not use the power point longer than necessary when the engine is not running.
Cigar/Cigarette lighter (if equipped) Do not plug optional electrical accessories into the cigarette lighter socket. Do not hold the lighter in with your hand while it is heating, this will damage the lighter element and socket. The lighter will be released from its heating position when it is ready to be used.
Power vent windows Do not leave children unattended in the vehicle and do not let children play with the power vent windows. They may seriously injure themselves. When closing the power vent windows, you should verify they are free of obstructions and ensure that children and/or pets are not in the proximity of the window openings.
POWER SIDE VIEW MIRRORS T o adjust your mirrors: 1. Rotate the control clockwise to adjust the right mirror and rotate the control counterclockwise to adjust the left mirror . 2. Move the control in the direction you wish to tilt the mirror . 3. Return to the center position to lock mirrors in place.
Fold-away mirrors Carefully pull the outside mirrors inwards when driving through a narrow space, like an automatic car wash. POWER ADJUSTABLE FOOT PEDALS (IF EQUIPPED) The accelerator and brake pedal should only be adjusted when the vehicle is stopped and the gearshift lever is in the P (Park) position.
Setting speed control The controls for using your speed control are located on the steering wheel for your convenience. 1. Press the ON control and release it. 2. Accelerate to the desired speed. 3. Press the SET + control and release it. 4. T ake your foot off the accelerator pedal.
Increasing speed while using speed control There are two ways to set a higher speed: • Press and hold the SET + control until you get to the desired speed, then release the control. Y ou can also use the SET + control to operate the T ap-Up function.
Turning of f speed control There are two ways to turn off the speed control: • Depress the brake pedal. This will not erase your vehicle’ s previously set speed. • Press the speed control OFF control. Note: When you turn off the speed control or the ignition, your speed control set speed memory is erased.
CENTER CONSOLE (IF EQUIPPED) Y our vehicle may be equipped with a utility compartment. POSITIVE RETENTION FLOOR MA T (IF EQUIPPED) T o install floor mats that have a retention post: Position the floor mat so that the eyelet is over the pointed end of the retention post and rotate forward to lock in.
Programming Do not program HomeLink 威 with the vehicle parked in the garage. Note: Y our vehicle may require the ignition switch to be turned to the ACC position for programming and/or operation of the HomeLink 威 .
Note: If the indicator light blinks rapidly for two seconds and then turns to a continuous red, proceed with Steps 6 through 8 to complete programming of a rolling code equipped device.
Operating the HomeLink 姞 Wireless Control System T o operate, simply press and release the appropriate HomeLink 威 button. Activation will now occur for the trained product (garage door , gate operator , security system, entry door lock, or home or office lighting etc.
MESSAGE CENTER (IF EQUIPPED) W ith the ignition in the ON position, the message center , located on your instrument cluster , displays important vehicle information through a constant monitor of vehicle systems. Y ou may select display features on the message center for a display of status preceded by a brief indicator chime.
DTE is calculated using a running average fuel economy , which is based on your recent driving history of 500 miles (800 km). This value is not the same as the average fuel economy display . The running average fuel economy is reinitialized to a factory default value if the battery is disconnected.
Setup menu Press this control for the following displays: • Language • Units (English/Metric) • System Check Language 1. Select this function from the SETUP menu for the current language to be displayed. 2. Pressing the RESET control cycles the message center through each of the language choices.
System check Selecting this function from the SETUP menu causes the message center to cycle through each of the systems being monitored. For each of the monitored systems, the message center will indicate a warning message for three seconds when there is a malfunction.
• W arning returns upon another event. This acts as a reminder that these warning conditions still exist within the vehicle. Driver’ s door ajar W arning cannot be reset Passenger door ajar Left r.
CHECK BRAKE SYSTEM. Displayed when the braking system is not operating properly . If the warning stays on or continues to come on, contact your authorized dealer as soon as possible. CHECK BRAKE LAMPS. Displayed when the brake lamps are activated and at least one is burned out.
An oil change is required whenever indicated by the message center . USE ONL Y RECOMMENDED ENGINE OILS. T o reset the oil monitoring system to 100% after each oil change [approximately 5,000 miles (8,000 km) or 180 days] perform the following: 1. Press the SETUP control to access the System Check function.
2. Press and release the RESET control to display “OIL LIFE XX% HOLD RESET NEW”. 3. Press and hold the RESET control for 2 seconds to display “IF NEW OIL HOLD RESET”.
LIFTGATE Unlock the liftgate (but not release it) with the power door lock system and remote entry transmitter . T o open the liftgate, pull the liftgate handle rearward. • Do not open the liftgate in a garage or other enclosed area with a low ceiling.
Keep the keys out of the reach of children. Do not allow children to play on or near an open or moving power liftgate. Exercise care, when power opening or closing the PLG in a garage or other enclosed area with a low ceiling or close to a wall/garage door .
T o power open the PLG with outside release handle: 1. Ensure that the Power Door Lockout Control in the overhead console is ON. 2. Ensure that the PLG is unlocked, using the remote entry transmitter or power door unlock. Refer to Remote Entry System in the Locks and security chapter .
PLG encounters an obstacle while opening, the PLG will stop when it encounters a solid obstacle. Close the liftgate manually and remove the obstruction.
CARGO AREA FEATURES Cargo net (if equipped) The cargo pouch net secures lightweight objects in the cargo area. Attach the net to the anchors provided. Do not put more than 50 lbs. (22 kg) in the net. The cargo net is not designed to restrain objects during a collision or heavy braking.
T o adjust the cross-bar (if equipped) position: 1. Loosen the thumbwheel at both ends of the cross-bar (both cross-bars are adjustable). 2. Slide the cross-bar to the desired location. 3. T ighten the thumbwheel at both ends of the cross-bar . T o remove the cross-bar assembly (if equipped): 1.
T o reinstall the cross-bar assembly (if equipped): 1. Slide the cross-bar into the rail track with the arrow facing towards the front of the vehicle. Slide the bar forward passed the retaining clip. 2. Firmly tighten the thumbscrews at both ends of the cross-bar .
KEYS The key operates all locks on your vehicle. In case of loss, replacement keys are available from your dealer . Y ou should always carry a second key with you in a safe place in case you require it in an emergency . Refer to the SecuriLock 娂 passive anti-theft system section in this chapter for more information.
Unlocking the liftgate during a battery failure In the event of a vehicle power failure affecting the liftgate latch, the liftgate can be unlocked manually . 1. Locate the liftgate trim access panel in the center of the liftgate. 2. Using your key , a small screwdriver or knife, pry off the access panel.
CHILDPROOF DOOR LOCKS • When these locks are set, the sliding doors cannot be opened with the inside handle. • The sliding doors can be opened from the outside when the doors are unlocked. The childproof lock controls are located on front edge of each sliding door and must be set separately for each door .
• 3–button remote • 5–button remote • 6–button remote The remote entry system allows you to: • lock or unlock all vehicle doors and liftgate without a key . • unlock/open a driver’ s side power sliding door and/or passenger side power sliding door (if equipped).
If there are problems with the remote entry system, make sure to take ALL remote entry transmitters with you to the authorized dealer in order to aid in troubleshooting the problem. Unlocking the doors 1. Press and release to unlock the driver’ s door .
Opening power liftgate (PLG) (if equipped) Press the control twice within three seconds to power open the power liftgate. The interior lamps will illuminate. Make sure all persons are clear of the power liftgate area before using the power liftgate controls to open or close the liftgate.
If any of the doors, the liftgate or the hood (if equipped with perimeter alarm) are not properly closed, the horn will make two quick chirps and the parklamps will not flash. Sounding a panic alarm Press to activate the alarm. The alarm will cycle the horn, the turn signals will flash, and the interior lamps will illuminate.
5. Snap the two halves back together . Note: Replacement of the battery will not cause the remote transmitter to become deprogrammed from your vehicle.
9. T urn the ignition to the 3 (OFF) position after you have finished programming all of the remote entry transmitters. 10. The doors will lock, then unlock, to confirm that the programming mode has been exited.
• Head lamps • Park lamps • T ail lamps The system will automatically turn off if: • the vehicle is locked using the remote entry system, the keyless entry keypad, or • the ignition is turned to the 4 (ON) position, or • after 25 seconds of illumination.
Press to automatically move the driver seat, side view mirrors and adjustable pedals to the desired memory position. Associating the remote transmitter with the memory feature T o activate this feature: 1. Position the driver’ s seat, side view mirrors and adjustable pedals to the positions you desire.
The keypad can be operated with the factory set 5–digit entry code; this code is located: • on the owner’ s wallet card in the glove box, • marked on the passenger compartment fuse panel (located below and to the left of the steering, near the brake pedal), • and is available from your authorized dealer .
• The factory code will work even after you have set your own personal codes. • Do not set a code that uses five of the same number . • Do not use five numbers in sequential order . Erasing personal code 1. Enter the factory set 5–digit code. 2.
Relock The autolock feature repeats when: • an “autolock” occurrence has already taken place, • the brake is depressed while vehicle speed is less than 5 mph (8 km/h), • all vehicle doors become closed again, and • then the vehicle increases to more than 5 mph (8 km/h).
5. T urn the ignition back to the 4 (ON) position. The horn will chirp. 6. Press the unlock control, then press the lock control. The horn will chirp once if autolock was deactivated or twice (one short and one long chirp) if autolock was activated. 7.
If any of these items are present, you need to prevent these objects from touching the coded key while starting the engine. These objects cannot damage the coded key , but may cause a momentary “no start” condition if they are too close to the key when starting the engine.
1. Insert the first previously programmed coded key into the ignition and turn the ignition from the 3 (OFF) position to the 4 (ON) position [maintain ignition in 4 (ON) for at least three seconds, but no more than ten seconds].
Arming the system When armed, this system will help protect your vehicle from unauthorized entry . When unauthorized entry occurs, the system will flash the turn signal lamps and side repeaters and honk the horn. The system is ready to arm whenever the key is removed from the ignition.
SEATING Notes: Reclining the seatback can cause an occupant to slide under the seat’ s safety belt, resulting in severe personal injuries in the event of a collision. Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop.
Push control to lower head restraint. Adjusting the front manual seat (if equipped) Never adjust the driver’ s seat or seatback when the vehicle is moving. Always drive and ride with your seatback upright and the lap belt snug and low across the hips.
Before returning the seatback to its original position, make sure that cargo or any objects are not trapped behind the seatback. After returning the seatback to its original position, pull on the seatback to ensure that it has fully latched. An unlatched seat may become dangerous in the event of a sudden stop or collision.
Press to raise or lower the front portion of the seat cushion. Press to raise or lower the rear portion of the seat cushion. Press the control to move the seat forward, backward, up or down. Heated seats (if equipped) T o operate the heated seats: • Push the control located on the climate control system panel once to activate high heat.
Using the manual lumbar support (if equipped) The lumbar control is located on the inboard side of the seat under the armrest. Rotate the control to change the firmness of the lumbar support.
REAR SEATS Head restraints Lift the head restraint so that it is located directly or as close as possible behind your head. The head restraints can be moved up and down by pulling up on the head restraint. Push button to lower head restraint. Seat mounted cup holders (if equipped) Deploy by pressing the button on top of the cupholder .
The cupholder is designed to detach from the seat when subjected to heavy load. The cupholder can be reinstalled by returning to the closed position. Use only soft cups in the cupholder . Hard objects can injure you in a collision. Adjusting 2nd row seats (if equipped) Lift control to adjust seat forward or backward.
• 2nd row bench seat (if equipped) Note: This seat can be moved forward to keep a child in a LA TCH child restraint attached to the LA TCH anchors at the center of the bench seat close to the front seat occupants or to increase cargo room without removing the seat.
Accessing the third row seat with a second row bucket seat Ensure head restraint is in the full down position and seat is adjusted to full rear position (if equipped). Note: Place the front row seat in a forward position to allow the 2nd row to be fully upright.
Continuing to lift the handle will tumble the seat forward, allowing easier access to the third row seat. After entering the 3rd row seat, return the seat from the tumbled position and latch it to the floor . Operate recline control to return the seatback to the upright position.
Before returning the seatback to its original position, make sure that cargo or any objects are not trapped underneath the seatback. After returning the seatback to its original position, pull on the seatback to ensure that it has fully latched. An unlatched seat may become dangerous in the event of a sudden stop or collision.
Second row bench seat T o exit the third row , activate the easy entry system by pulling on the strap on the rear of the seat. This will cause the seatback to flip forward and the seat track latches to open. Push the seat forward to allow easier exit from the third row .
3. Place seat in tumbled position. (See Accessing 3rd row seat ) 4. From inside the vehicle, pull up on front floor release handle. 5. Rotate the seat rearward at a 30 to 45 degree angle.
6. W ith the assist handle, pull the seat rearward. 7. Remove the seat from vehicle. Second row bench seat 1. Detach the lap/shoulder belts from both sides of the seat by inserting a seat belt tongue or key into the buckle release slot, pushing upward as shown, and pulling out the mini-tongue on the end of the seat belt.
2. Find the clips attached near the ends of the lap/shoulder belts. 3. Clip the end of the belt to the stationary portion of the shoulder belt coming out of the trim panel. The end of the shoulder belt must be clipped in order to keep it from striking anything during vehicle operation.
4. Position seatback in full down position. 5. From behind seat pull straight back on the release handles located on each side of the seat, releasing the rear floor latches. 6. Lift up the seat by the release handles to clear the floor latches and then pull the seat rearward until the front hooks have come out of the floor tubs.
2. Install seat onto rear pin of front tub at a 30 to 45 degree angle. 3. Rotate the seat forward until it latches onto the front pin. 4. Rotate seat rearward until the back of the seat latches onto the floor .
5. Operate recline lever and push the seat back upright. Ensure seat is latched to vehicle floor by pushing/pulling on seat. If not latched, the seat may cause injury during a sudden stop. Before returning the seatback to its original position, make sure that cargo or any objects are not trapped behind the seatback.
3. Lower back of seat onto the rear tubs until both release controls latch into place. Be sure that the seat is locked in place both front and back. Do not place the seat front hooks on the front most pin of the front tub. Doing so will not allow the seat to fully install in vehicle.
2. If you plan to carry very large objects or items that might damage the center lap/shoulder belt, detach the belt from the seat. Use a key or seat belt tongue to release the buckle.
4. Store the belt in the housing found on the ceiling by inserting the smaller tongue in the slot provided. Note: The seat can be stowed with the safety belt connected if desired. Store the tongue of the sliding latchplate in the belt pocket to avoid potential damage to the seat.
Important: If you don’t let go of the number 1 strap before the seat back folds completely , the seat may not stow flat in the tub. Refer to the label attached to the rear of the vehicle seat. 7. Release the cushion latches by pulling the number 2 strap.
8. Pull the number 3 strap on the seat back to tumble seat all the way in to the tub in the floor . Do not use the seat anchors as cargo tie downs. Unstowing the third row seat Ensure seat latching area is free of objects. 1. Lift the seat out of the tub in the floor by pulling up on the exposed strap or handle.
2. T o return the seat back to the seating position, pull the number 1 strap, then while holding the number 1 strap, pull the number 3 strap to raise the seat back. 3. Release the number 1 strap to allow the seat to lock, then release the number 3 strap.
Reclining the seatback can cause an occupant to slide under the seat’ s safety belt, resulting in severe personal injuries in the event of a collision. T ailgate function The 3rd row seat is equipped with a tailgate function to be utilized when the vehicle is parked and engine turned off.
3. T o return the seat, ensure seat latching area is free of objects. Then, raise the seat off the liftgate scuff plate and push at the top of the seat back to rotate the seat back onto the latches. Pull up on the head restraints to raise them. Ensure seat is latched to vehicle floor by pushing/pulling on seat.
conditions. A collection of crash and occupant sensors provides information to the Restraints Control Module (RCM). During a crash, the RCM activates the safety belt pretensioners and/or either one or both stages of the dual-stage airbag supplemental restraints based on crash severity and occupant conditions.
occupants, this occurs when the occupant is not properly restrained by seat belts or child safety seats and they move forward during pre-crash braking. The most effective way to reduce the risk of unnecessary injuries is to make sure all occupants are properly restrained.
Front safety belt energy management retractors The front outboard safety belt energy management retractors allow webbing to be pulled out of the retractor in a gradual and controlled manner in response to the occupant’ s forward momentum.
Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision. All occupants of the vehicle, including the driver , should always properly wear their safety belts, even when an air bag supplemental restraint system (SRS) is provided.
Combination lap and shoulder belts 1. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) until you hear a snap and feel it latch. Make sure the tongue is securely fastened in the buckle. 2. T o unfasten, push the release button and remove the tongue from the buckle.
All safety restraints in the vehicle are combination lap and shoulder belts. All of the passenger combination lap and shoulder belts have two types of locking modes described below: V ehicle sensitive.
• Grasp the shoulder portion and pull downward until the entire belt is pulled out. • Allow the belt to retract. As the belt retracts, you will hear a clicking sound.
Position the safety belt height adjusters so that the belt rests across the middle of your shoulder . Failure to adjust the safety belt properly could reduce the effectiveness of the safety belt and increase the risk of injury in a collision.
Conditions of operation If... Then... The driver’ s safety belt is not buckled before the ignition switch is turned to the ON position... The safety belt warning light illuminates 1-2 minutes and the warning chime sounds 4-8 seconds. The driver’ s safety belt is buckled while the indicator light is illuminated and the warning chime is sounding.
If... Then... The driver’ s and front passenger’ s safety belts are buckled before the ignition switch is turned to the ON position or less than 1-2 minutes have elapsed since the ignition switch has been turned ON... The BeltMinder 娂 feature will not activate.
Reasons given... Consider ... “Belts are uncomfortable” W e design our safety belts to enhance comfort. If you are uncomfortable - try different positions for the safety belt upper anchorage and seatback which should be as upright as possible; this can improve comfort.
Do not sit on top of a buckled safety belt to avoid the BeltMinder 娂 chime. Sitting on the safety belt will increase the risk of injury in an accident. T o disable (one-time) or deactivate the BeltMinder 娂 feature please follow the directions stated below .
• Step 3 must be completed within 50 seconds after the safety belt warning light turns off. 3. For the seating position being disabled, at a moderate speed, buckle then unbuckle the safety belt 9 times, ending in the unbuckled state. (Step 3 must be completed within 50 seconds after the safety belt warning light turns off.
assemblies (if equipped), LA TCH child seat tether anchors and lower anchors (if equipped), and attaching hardware, should be inspected after a collision. Ford recommends that all safety belt assemblies in use in vehicles involved in a collision be replaced.
The airbag supplemental restraint system (SRS) is designed to work in conjunction with the safety belts to help protect the driver and front outboard passenger from certain upper body injuries. The term “supplemental restraint” means the airbags are intended as a supplement to the safety belts.
T o properly position yourself away from the airbag: • Move your seat to the rear as far as you can while still reaching the pedals comfortably . • Recline the seat slightly one or two degrees from the upright position. Do not put anything on or over the airbag module.
How does the airbag supplemental restraint system work? The airbag SRS is designed to activate when the vehicle sustains longitudinal deceleration sufficient to cause the sensors to close an electrical circuit that initiates airbag inflation.
Several air bag system components get hot after inflation. Do not touch them after inflation. If the air bag has deployed, the air bag will not function again and must be replaced immediately . If the air bag is not replaced, the unrepaired area will increase the risk of injury in a collision.
• the system determines that a small child is present in a forward-facing child restraint that is installed according to the manufacturer’ s instructions, • the system determines that a small ch.
• When the front passenger sensing system enables the front passenger frontal airbag (may inflate), the indicator will be unlit and stay unlit. If a person of adult size is sitting in the front pass.
The front passenger sensing system may detect small or medium objects placed on the seat cushion. For most objects that are in the front passenger seat, the passenger airbag will be disabled. Even though the passenger airbag is disabled, the ⬙ pass airbag off ⬙ lamp may or may not be illuminated according to the table below .
T o reduce the risk of possible serious injury: Do not stow objects in seat back map pocket (if equipped) or hang objects off seat back if a child is in the front passenger seat. Do not place objects underneath the front passenger seat or between the seat and the center console (if equipped).
If it is necessary to modify an advanced front airbag system to accommodate a person with disabilities, contact the Ford Customer Relationship Center at the phone number shown in the Customer Assistance section of this Owner’ s Guide .
Do not lean your head on the door . The side airbag could injure you as it deploys from the side of the seatback. Do not attempt to service, repair , or modify the airbag SRS, its fuses or the seat cover on a seat containing an airbag. See your authorized dealer .
The airbag was designed to inflate between the door panel and occupant to further enhance the protection provided occupants in side impact collisions. The airbag SRS is designed to activate when the vehicle sustains lateral deceleration sufficient to cause the sensors to close an electrical circuit that initiates airbag inflation.
Do not lean your head on the door . The Safety Canopy 娂 could injure you as it deploys from the headliner . Do not attempt to service, repair , or modify the Safety Canopy 娂 system, its fuses, the A, B, C or D pillar trim, or the headliner on a vehicle containing a Safety Canopy 娂 .
• An inflatable nylon curtain with a gas generator concealed behind the headliner and above the doors (one on each side of vehicle). • A headliner designed to flex open above the side doors to allow Safety Canopy 娂 deployment. • The same readiness airbag light, electronic control and diagnostic unit as used for the front airbags.
If the Safety Canopy 娂 system has deployed, the Safety Canopy 娂 will not function again unless replaced. The Safety Canopy 娂 system (including the A, B, C, and D pillar trim) must be inspected and serviced by an authorized dealer . If the Safety Canopy 娂 is not replaced, the unrepaired area will increase the risk of injury in a collision.
Important child restraint precautions Y ou are required by law to use safety restraints for children in the U.S. and Canada. If small children (generally children who are four years old or younger and who weigh 40 lb. [18 kg] or less) ride in your vehicle, you must put them in safety seats made especially for children.
T o improve the fit of both the lap and shoulder belt on children who have outgrown child safety seats, Ford Motor Company recommends use of a belt-positioning booster . Booster seats position a child so that safety belts fit better . They lift the child up so that the lap belt rests low across the hips and the knees bend comfortably .
• Those with a high back. If, with a backless booster seat, you cannot find a seating position that adequately supports your child’ s head, a high back booster seat would be a better choice. Both can be used in any vehicle in a seating position equipped with lap/shoulder belts if your child is over 40 lb.
Child booster seats Children outgrow a typical convertible or toddler seat when they weigh 40 lb. (18 kg) and are around 4 years of age. Although the lap/shoulder belt will provide some protection, these children are still too small for lap/shoulder belts to fit properly , which could increase the risk of serious injury .
T ypes of booster seats There are two types of belt-positioning booster seats: • Those that are backless. If your backless booster seat has a removable shield, remove the shield and use the lap/shoulder belt.
Children and booster seats vary widely in size and shape. Choose a booster that keeps the lap belt low and snug across the hips, never up across the stomach, and lets you adjust the shoulder belt to cross the chest and rest snugly near the center of the shoulder .
The importance of shoulder belts Using a booster without a shoulder belt increases the risk of a child’ s head hitting a hard surface in a collision. For this reason, you should never use a booster seat with a lap belt only . It is best to use a booster seat with lap/shoulder belts in the back seat- the safest place for children to ride.
When installing a child safety seat: • Review and follow the information presented in the Airbag Supplemental Restraint System section in this chapter . • Use the correct safety belt buckle for that seating position. • Insert the belt tongue into the proper buckle until you hear a snap and feel it latch.
Installing child safety seats with combination lap and shoulder belts Airbags can kill or injure a child in a child seat. NEVER place a rear -facing child seat in front of an active airbag. If you must use a forward-facing child seat in the front seat, move the seat all the way back.
3. While holding the shoulder and lap belt portions together , route the tongue through the child seat according to the child seat manufacturer’ s instructions.
7. Pull the lap belt portion across the child seat toward the buckle and pull up on the shoulder belt while pushing down with your knee on the child seat.
The tether anchors in your vehicle are in the positions shown: The front passenger seat with power adjustment does not have a tether anchor . The two tether anchors on the back of the second row bench.
2. Route the child safety seat tether strap over the back of the seat. If the head restraint is adjustable, route the tether strap under the head restraint and between the head restraint posts. If the top of the safety seat hits the head restraint, raise the head restraint to let the child seat fit further rearward.
If the tether strap is clipped incorrectly (as shown) the child safety seat may not be retained properly in the event of a collision. 5. Rotate the tether strap clip. 6. Install the child safety seat tightly using the LA TCH anchors or safety belts. Follow the instructions in this chapter .
Rear seating positions Follow Steps 1–7 as described above for the following available seats: • 2nd row bucket • 2nd row bench • 3rd row bench For additional important safety information on the proper use of safety belts, child seats and infant seats, please read the entire Seating and safety restraints chapter in this owner’ s guide.
Y our vehicle has LA TCH anchors for child seat installation at the seating positions marked with the child seat symbol. If your vehicle has a second row bench seat, one child seat can be placed in each outboard seating position, or one LA TCH child seat can be placed in the center of the seat only .
Follow the child seat manufacturer’ s instructions to properly install a child seat with LA TCH attachments. Attach LA TCH lower attachments of the child seat only to the anchors shown.
INFORMA TION ABOUT UNIFORM TIRE QUALITY GRADING New vehicles are fitted with tires that have a rating on them called T ire Quality Grades. The Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width.
The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics.
Increasing the inflation pressure beyond this pressure will not increase the tire’ s load carrying capability . • kPa: Kilopascal, a metric unit of air pressure.
Under -inflation is the most common cause of tire failures and may result in severe tire cracking, tread separation or ⬙ blowout ⬙ , with unexpected loss of vehicle control and increased risk of injury . Under -inflation increases sidewall flexing and rolling resistance, resulting in heat buildup and internal damage to the tire.
when you get to the pump. It is normal for tires to heat up and the air pressure inside to go up as you drive. Never “bleed” or reduce air pressure when tires are hot. 2. Remove the cap from the valve on one tire, then firmly press the tire gauge onto the valve and measure the pressure with the tire gauge.
Tire wear When the tread is worn down to 1/16th of an inch (2 mm), tires must be replaced to help prevent your vehicle from skidding and hydroplaning. Built-in treadwear indicators, or “wear bars”, which look like narrow strips of smooth rubber across the tread will appear on the tire when the tread is worn down to 1/16th of an inch (2 mm).
If your vehicle is stuck in snow , mud, sand, etc., do not rapidly spin the tires; spinning the tires can tear the tire and cause an explosion. A tire can explode in as little as three to five seconds. Never spin the tires in excess of the 35 mph (55 km/h) point indicated on the speedometer .
• Front Wheel Drive (FWD) vehicles (front tires at top of diagram) Sometimes irregular tire wear can be corrected by rotating the tires. Note: If your tires show uneven wear ask an authorized dealer to check for and correct any wheel misalignment, tire imbalance or mechanical problem involved before tire rotation.
TIRE REPLACEMENT REQUIREMENTS Y our vehicle is equipped with tires designed to provide a safe ride and handling capability . Only use replacement tires and wheels that are the same size and type (such as P-metric versus L T -metric or all-season versus all-terrain) as those originally provided by Ford.
Information on “P” type tires P215/65R15 95H is an example of a tire size, load index and speed rating. The definitions of these items are listed below . (Note that the tire size, load index and speed rating for your vehicle may be different from this example.
Note: Y ou may not find this information on all tires because it is not required by federal law . Letter rating Speed rating - mph (km/h) M 81 mph (130 km/h) N 87 mph (140 km/h) Q 99 mph (159 km/h) R .
12. T readwear , T raction and T emperature Grades • T readwear: The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course.
Additional information contained on the tire sidewall for “L T” type tires “L T” type tires have some additional information beyond those of “P” type tires; these differences are described below: 1. LT: Indicates a tire, designated by the T ire and Rim Association (T&RA), that is intended for service on light trucks.
Information on “T” type tires “T” type tires have some additional information beyond those of “P” type tires; these differences are described below: T145/80D16 is an example of a tire size. Note: The temporary tire size for your vehicle may be different from this example.
TIRE PRESSURE MONITORING SYSTEM (TPMS) Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label.
Changing tires with TPMS Each road tire is equipped with a tire pressure sensor fastened to the inside rim of the wheel. The pressure sensor is covered by the tire and is not visible unless the tire is removed. The pressure sensor is located opposite (180 degrees) from the valve stem.
wheel/tire needs to be repaired and put back on your vehicle. During this time, the low tire warning light can periodically return or stay on, depending on the state of the damaged road wheel/tire. This will include messages from the message center (if equipped).
Low T ire Pressure W arning Light Possible cause Customer Action Required Solid W arning Light T ire(s) under -inflated 1. Check your tire pressure to ensure they are properly inflated; refer to Inflating your tires in this chapter .
Low T ire Pressure W arning Light Possible cause Customer Action Required Flashing W arning Light (flashes for 20 to 30 seconds either at start-up or while driving) Spare tire in use Y our temporary spare tire is in use. Repair the damaged road wheel and re-mount it on the vehicle to restore system functionality .
How temperature affects your tire pressure The T ire Pressure Monitoring System (TPMS) monitors tire pressure in each pneumatic tire. The pressure in each tire is dependent upon several factors, one of them being the contained air temperature (temperature of the air inside the tire).
Follow these guidelines when using snow tires and chains: • Use only cable type SAE Class “S” chains. Conventional link or other type chains may cause damage to your vehicle’ s wheelhouse and/or underbody . • These cable type chains should only be applied to the front wheels.
Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be found on the T ire Label on the B-Pillar or the edge of the driver’ s door (vehicles exported outside the US and Canada may not have a T ire Label).
Example only: Cargo W eight – includes all weight added to the Base Curb W eight, including cargo and optional equipment. When towing, trailer tongue load or king pin weight is also part of cargo weight.
GA W (Gross Axle W eight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload. GA WR (Gross Axle W eight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear).
GVWR (Gross V ehicle W eight Rating) – is the maximum allowable weight of the fully loaded vehicle (including all options, equipment, passengers and cargo). The GVWR is shown on the Safety Compliance Certification Label located on the B-Pillar or the edge of the driver’ s door .
mandatory options, no cargo (internal or external), a tongue load of 10–15% (conventional trailer) or king pin weight of 15–25% (fifth wheel trailer), and driver only (150 lb. [68 kg]). Consult your authorized dealer (or the RV and T railer T owing Guide provided by your authorized dealer) for more detailed information.
capacity to carry you, 4 of your friends and all the golf bags? Y ou and four friends average 220 lb. (99 kg) each and the golf bags weigh approximately 30 lb. (13.5 kg) each. The calculation would be: 1400 – (5 x 220) – (5 x 30) = 1400 – 1100 – 150 = 150 lb.
A new underbody wiring harness (14406) will be a component to this kit and will need to be installed, if applicable, per instructions located in the service kit. If your vehicle has the optional trailer tow package it comes with heavy duty cooling fans, auxiliary transmission fluid cooler , an auxiliary engine oil cooler (4.
V ehicle towing capability/ T railer hitch requirement T railer Model/ Engine GCWR - lb. (kg) Hitch type required T railer W eight range - lb. (kg) T ongue load V an, 3.9L 7000 (3175) Class I Non- Equalizing W eight Carrying 0-2000 (0–907) 10–15% of TW (200 lb.
T ongue Load section in the trailer towing chart earlier in this section for range details on a specific trailer load. Safety chains Always connect the trailer’ s safety chains to the hook retainers on the hitch. T o connect the trailer’ s safety chains, cross the chains under the trailer tongue and allow slack for turning corners.
• T urn off the speed control. The speed control may shut off automatically when you are towing on long, steep grades. • Consult your local motor vehicle speed regulations for towing a trailer . • T o eliminate excessive shifting, use a lower gear .
RECREATIONAL TOWING Follow these guidelines for your specific powertrain combination to tow your vehicle with all four wheels on the ground (such as behind a recreational vehicle). These guidelines are designed to ensure that your transmission is not damaged due to insufficient lubrication.
STARTING Positions of the ignition 1. ACCESSORY , allows the electrical accessories such as the radio to operate while the engine is not running. 2. LOCK, locks the steering wheel, automatic transmission gearshift lever and allows key removal. 3. OFF , shuts off the engine and all accessories without locking the steering wheel.
Do not park, idle, or drive your vehicle in dry grass or other dry ground cover . The emission system heats up the engine compartment and exhaust system, which can start a fire. Do not start your vehicle in a closed garage or in other enclosed areas. Exhaust fumes can be toxic.
• T urn the key to 4 (ON) without turning the key to 5 (ST ART). Some warning lights will briefly illuminate. See W arning lights and chimes in the Instrument Cluster chapter for more information regarding the warning lights. Starting the engine Note: Whenever you start your vehicle, release the key as soon as the engine starts.
Important ventilating information If the engine is idling while the vehicle is stopped for a long period of time, open the windows at least one inch (2.
ABS warning lamp The ABS lamp in the instrument cluster momentarily illuminates when the ignition is turned on. If the light does not illuminate during start up, remains on or flashes, the ABS may be disabled and may need to be serviced. Even when the ABS is disabled, normal braking is still effective.
Parking brake T o set the parking brake, pull the handle up as far as possible. The BRAKE warning lamp will illuminate and will remain illuminated until the parking brake is released. T o release, press and hold the button, pull the handle up slightly , then push the handle down.
• Maneuvering quickly to avoid an accident, pedestrian or obstacle • Hitting a patch of ice • Changing lanes on a snow-rutted road • Entering a snow-free road from a snow-covered side street, .
• A slight deceleration of the vehicle • The TRAC ACTIVE indicator light will illuminate • If your foot is on the brake pedal, you will feel a vibration in the pedal. • If the driving condition is severe and your foot is not on the brake, the brake pedal will move to apply higher brake forces.
If the steering wanders or pulls, check for: • an improperly inflated tire • uneven tire wear • loose or worn suspension components • loose or worn steering components • improper steering alignment A high crown in the road or high crosswinds may also make the steering seem to wander/pull.
Do not drive your vehicle until you verify that the brakelamps are working. Always set the parking brake fully and make sure the gearshift is latched in P (Park). T urn the ignition to the LOCK position and remove the key whenever you leave your vehicle.
T o put your vehicle in gear: • Start the engine • Depress the brake pedal • Move the gearshift lever into the desired gear T o put your vehicle in P (Park): • Come to a complete stop • Move the gearshift lever and securely latch it in P (Park) Always set the parking brake fully and make sure the gearshift is latched in P (Park).
When parking, do not use the gearshift in place of the parking brake. Always set the parking brake fully and make sure that the gearshift is securely latched in Park (P). T urn off the ignition whenever you leave your vehicle. Never leave your vehicle unattended while it is running.
This system is not designed to prevent contact with small or moving objects. The system is designed to provide a warning to assist the driver in detecting large stationary objects to avoid damaging the vehicle. The system may not detect smaller objects, particularly those close to the ground.
The RSS is automatically enabled when the gear selector is placed in R (Reverse) and the ignition is ON. The park aid disable switch allows the driver to disable the RSS only when the ignition is ON, and the gear selector is in R (Reverse). The OFF indicator remains illuminated when the system is disabled.
ROADSIDE ASSISTANCE Getting roadside assistance T o fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program.
U.S. Ford or Mercury vehicle customers who require roadside assistance, call 1–800–241–3673; Lincoln vehicle customers call 1–800–521–4140. Canadian customers who require roadside assistance, call 1–800–665–2006. If you need to arrange roadside assistance for yourself, Ford Motor Company will reimburse a reasonable amount.
This switch is located behind the service panel on the right side of the cargo area. T o reset the switch: 1. T urn the ignition OFF . 2. Check the fuel system for leaks. 3. If no leaks are apparent, reset the switch by pushing in on the reset button.
Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 2A Grey Grey — — — 3A Violet Violet — — — 4A Pink Pink — — — 5A T an T an — — — 7.
The fuses are coded as follows: Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 1 Relay Accessory delay relay 1 2 Relay Accessory delay relay 2 3 10A Front wiper motor.
Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 12 5A Brake-Shift Interlock (BSI) Run feed, Climate control system Run feed 13 5A Compass/Driver heated seat/Passenger .
Power distribution box The power distribution box is located in the engine compartment. The power distribution box contains high-current fuses that protect your vehicle’ s main electrical systems from overloads. Always disconnect the battery before servicing high current fuses.
Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 3 30A** Left cooling fan 4 30A** Starter solenoid 5 30A** Right-hand power sliding door 6 30A** SJB accessory #2 (driver power wi.
Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 40 15A* Engine #1 (A/C relay coil, IMRC, HEGO sensors, Canister purge, T ransmission module) 41 25A* Horn 42 10A* A/C clutch 43 1.
Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 61 — Not used 62 30A* SJB #3 – Right cornering/auxiliary lamps, Right low beam, Left front park/turn lamps, Left rear park/st.
Auxiliary relay box (cooling fans) The relay box is located in the engine compartment by the radiator . Fuse/Relay location Fuse amp rating Description 1 — Cooling fan relay #4 2 — Cooling fan rel.
The use of tire sealants may damage your tires. The use of tire sealants may also damage your T ire Pressure Monitoring System and should not be used. Y our vehicle is equipped with a Tire Pressure Monitoring System. Refer to T ire Pressure Monitoring System (TPMS) in the T ires, Wheels and Loading chapter for important information.
• ground clearance and parking at curbs • W inter driving capability Dissimilar spare tire/wheel information Failure to follow these guidelines could result in an increased risk of loss of vehicle control, injury or death. If you have a dissimilar spare tire/wheel, then it is intended for temporary use only .
• W inter weather driving capability • W et weather driving capability For vehicles equipped with 4WD, it is not recommended that the vehicle be operated in 4WD modes with a temporary emergency spare tire. If 4WD operation is necessary , do not operate above speeds of 10 mph (16 km/h) or for distances above 50 miles (80 km).
Have a flat tire serviced by an authorized dealer in order to prevent damage to the TPMS sensor , refer to T ire Pressure Monitoring System (TPMS) in the T ires, Wheels and Loading chapter . Replace the spare tire with a road tire as soon as possible.
2. T urn the wrench counterclockwise until cable is slack and tire can be slid rearward. 3. Remove the primary retainer from the center of the tire. Note: Do not stow the full size tire or any flat tire under the vehicle.
1. Park on a level surface, activate hazard flashers and set parking brake. 2. Place gearshift lever in P (Park), turn engine off, and block the diagonally opposite wheel.
If Ford Accessory Running Boards have been installed, use the jack adapters supplied with the running boards as described on the inside of the jack storage area. 6. Locate the jack notch next to the door closest to the tire you are changing, then place the jack on the frame rail directly behind the notch.
11. Remove the jack and fully tighten the lug nuts in the order shown. Refer to Wheel lug nut torque specifications later in this chapter for the proper lug nut torque specification.
3. Lay the tire flat and secure the cable with wing screw by installing it on the wing screw retainer in the floor and turning the wing screw clockwise. Y ou will hear an audible click when the tire is properly secured. 4. Check that the flat tire is properly secured.
WHEEL LUG NUT TORQUE SPECIFICATIONS Retighten the lug nuts to the specified torque at 500 miles (800 km) after any wheel disturbance (rotation, flat tire, wheel removal, etc.). Bolt size Wheel lug nut torque* lb.ft. N • m 1 ⁄ 2 x 20 100 135 * T orque specifications are for nut and bolt threads free of dirt and rust.
2. Do not disconnect the battery of the disabled vehicle as this could damage the vehicle’ s electrical system. 3. Park the booster vehicle close to the hood of the disabled vehicle making sure the two vehicles do not touch. Set the parking brake on both vehicles and stay clear of the engine cooling fan and other moving parts.
2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery . 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery .
4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’ s engine, away from the battery and the carburetor/fuel injection system. Do not use fuel lines, engine rocker covers or the intake manifold as grounding points.
Removing the jumper cables Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the ground metal surface. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery .
3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’ s battery . 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’ s battery .
WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or , if you are a member of a roadside assistance program, your roadside assistance service provider . It is recommended that your vehicle be towed by wheel lift or flatbed equipment.
If the vehicle is towed by other means or incorrectly , vehicle damage may occur . Ford Motor Company produces a towing manual for all authorized tow truck operators. Have your tow truck operator refer to this manual for proper hook-up and towing procedures for your vehicle.
GETTING THE SERVICES YOU NEED At home Y ou must take your Ford vehicle to an authorized dealer for warranty repairs. While any authorized dealer handling your vehicle line will provide warranty service, we recommend you return to your selling authorized dealer who wants to ensure your continued satisfaction.
In Canada: Customer Relationship Centre Ford Motor Company of Canada, Limited P .O. Box 2000 Oakville, Ontario L6J 5E4 1-800-565-3673 (FORD) www .ford.
In some states (in the U.S.) you must directly notify Ford in writing before pursuing remedies under your state’ s warranty laws. Ford is also allowed a final repair attempt in some states.
THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM (U.S. ONLY) Y our satisfaction is important to Ford Motor Company and to your dealer . Experience has shown that our customers have been very successful in achieving satisfaction by following the three-step procedure outlined on the front page of the W arranty Guide.
trucks which are within the terms of any applicable written new vehicle warranty are eligible for review , except those involving: • a non-Ford product • a non-authorized dealership • sales disp.
Y our application is reviewed and, if it is determined to be eligible, you will receive an acknowledgment indicating: • The file number assigned to your application. • The toll-free phone number of the DSB’ s independent administrator . Y our authorized dealer and a Ford Motor Company representative will then be asked to submit statements.
After a case is reviewed, the Board mails you a decision letter and a form on which to accept or reject the Board’ s decision. The decisions of the Board are binding on Ford (and, in some cases, on the authorized dealer) but not on consumers who are free to pursue other remedies available to them under state or federal law .
CAMV AP services are available in all territories and provinces. For more information, without charge or obligation, call your CAMV AP Provincial Administrator directly at 1-800-207-0685. FORD EXTENDED SERVICE PLAN Y ou can get more protection for your new car or light truck by purchasing Ford Extended Service Plan (Ford ESP) coverage.
If your vehicle must be serviced while you are traveling or living in Central America, the Caribbean, or the Middle East, contact the nearest authorized dealer . If the authorized dealer cannot help you, write or call: FORD MOTOR COMP ANY WORLDWIDE DIRECT MARKET OPERA TIONS 1555 Fairlane Drive Fairlane Business Park #3 Allen Park, Michigan 48101 U.
REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway T raffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company .
W ASHING THE EXTERIOR W ash your vehicle regularly with cool or lukewarm water and a neutral pH shampoo, such as Motorcraft Detail W ash (ZC-3–A), which is available from your authorized dealer . • Never use strong household detergents or soap, such as dish washing or laundry liquid.
• Remove particles such as bird droppings, tree sap, insect deposits, tar spots, road salt and industrial fallout before repairing paint chips. • Always read the instructions before using the products. ALUMINUM WHEELS AND WHEEL COVERS Aluminum wheels and wheel covers are coated with a clearcoat paint finish.
• Cover the highlighted areas to prevent water damage when cleaning the engine. • Never wash or rinse the engine while it is running; water in the running engine may cause internal damage. PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts.
• The wiper blades can be cleaned with isopropyl (rubbing) alcohol or Motorcraft Premium W indshield W asher Concentrate (ZC-32–A), available from your authorized dealer .
• Remove light stains and soil with Motorcraft Professional Strength Carpet & Upholstery Cleaner (ZC-54). • If grease or tar is present on the material, spot-clean the area first with Motorcraft Spot and Stain Remover (ZC-14).
quality products have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and appearance of your vehicle. Each product is made from high quality materials that meet or exceed rigid specifications.
SERVICE RECOMMENDATIONS T o help you service your vehicle: • W e highlight do-it-yourself items in the engine compartment for easy location. • W e provide scheduled maintenance information which makes tracking routine service easy .
OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the bottom left corner of the instrument panel. 2. Go to the front of the vehicle and release the auxiliary latch that is located under the front center of the hood. 3.
IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 3.9L/4.2L V6 engines 1. Brake fluid reservoir 2. Air filter assembly 3. Power distribution box 4. Battery 5. Automatic transmission fluid dipstick 6. Engine oil dipstick 7. Engine oil filler cap 8. W indshield washer fluid reservoir 9.
WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if the level is low . In very cold weather , do not fill the reservoir completely . Only use a washer fluid that meets Ford specification WSB-M8B16–A2. Do not use any special washer fluid such as windshield water repellent type fluid or bug wash.
CHANGING THE WIPER BLADES T o replace the wiper blades: 1. Pull the wiper arm away from the windshield and lock into the service position. 2. T urn the blade at an angle from the wiper arm. Push the lock pin manually to release the blade and pull the wiper blade down toward the windshield to remove it from the arm.
5. Locate and carefully remove the engine oil level indicator (dipstick). 6. W ipe the indicator clean. Insert the indicator fully , then remove it again.
• Do not overfill the engine with oil. Oil levels above this mark may cause engine damage. If the engine is overfilled, some oil must be removed from the engine by an authorized dealer . 7. Put the indicator back in and ensure it is fully seated. Adding engine oil 1.
economy requirements of the International Lubricant Standardization and Approval Committee (ILSAC), comprised of U.S. and Japanese automobile manufacturers. T o protect your engine’ s warranty use Motorcraft SAE 5W -20 or an equivalent 5W -20 oil meeting Ford specification WSS-M2C930-A.
If your battery has a cover/shield, make sure it is reinstalled after the battery has been cleaned or replaced. For longer , trouble-free operation, keep the top of the battery clean and dry . Also, make certain the battery cables are always tightly fastened to the battery terminals.
installed, the transaxle must relearn its adaptive strategy . Optimal shifting will resume within a few hundred kilometers (miles) of operation. Because your vehicle’ s engine is electronically controlled by a computer , some control conditions are maintained by power from the battery .
• Always dispose of automotive batteries in a responsible manner . Follow your local authorized standards for disposal. Call your local authorized recycling center to find out more about recycling automotive batteries.
When the engine is cold, check the level of the engine coolant in the reservoir . • The engine coolant should be at the “FULL COLD” level or within the “COLD FILL RANGE” as listed on the engine coolant reservoir (depending upon application).
Do not add engine coolant when the engine is hot. Steam and scalding liquids released from a hot cooling system can burn you badly . Also, you can be burned if you spill coolant on hot engine parts. Do not put engine coolant in the windshield washer fluid container .
coolant degas system with a pressurized cap, or if it is necessary to remove the coolant pressure relief cap on the radiator of a vehicle with an overflow system, follow these steps to add engine coolant. T o reduce the risk of personal injury , make sure the engine is cool before unscrewing the coolant pressure relief cap.
Used engine coolant should be disposed of in an appropriate manner . Follow your community’ s regulations and standards for recycling and disposing of automotive fluids. Coolant refill capacity T o find out how much fluid your vehicle’ s cooling system can hold, refer to Refill capacities in this section.
FUEL FILTER For fuel filter replacement, see your authorized dealer . Refer to scheduled maintenance information for the appropriate intervals for changing the fuel filter .
Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materials and any open flames before refueling your vehicle. • Always turn off the vehicle before refueling. • Automotive fuels can be harmful or fatal if swallowed.
Refueling Fuel vapor burns violently and a fuel fire can cause severe injuries. T o help avoid injuries to you and others: • Read and follow all the instructions on the pump island; • T urn off yo.
If you must replace the fuel filler cap, replace it with a fuel filler cap that is designed for your vehicle. The customer warranty may be void for any damage to the fuel tank or fuel system if the correct genuine Ford or Motorcraft fuel filler cap is not used.
Octane recommendations Y our vehicle is designed to use “Regular” unleaded gasoline with pump (R+M)/2 octane rating of 87. W e do not recommend the use of gasolines labeled as “Regular” that are sold with octane ratings of 86 or lower in high altitude areas.
• The indicator may come on. For more information on the “Check Engine” or the “Service engine soon” indicator , refer to W arning lights and chimes in the Instrument Cluster chapter . ESSENTIALS OF GOOD FUEL ECONOMY Measuring techniques Y our best source of information about actual fuel economy is you, the driver .
• Have the vehicle loading and distribution the same every time. Y our results will be most accurate if your filling method is consistent. Calculating fuel economy 1. Fill the fuel tank completely and record the initial odometer reading (in miles or kilometers).
• Revving the engine before turning it off may reduce fuel economy . • Using the air conditioner or defroster may reduce fuel economy . • Y ou may want to turn off the speed control in hilly terrain if unnecessary shifting between third and fourth gear occurs.
EP A window sticker Every new vehicle should have the EP A window sticker . Contact your authorized dealer if the window sticker is not supplied with your vehicle. The EP A window sticker should be your guide for the fuel economy comparisons with other vehicles.
Exhaust leaks may result in entry of harmful and potentially lethal fumes into the passenger compartment. Do not make any unauthorized changes to your vehicle or engine.
the description in the W arning lights and chimes section of the Instrument Cluster chapter . Y our vehicle may not pass the I/M test with the indicator on. If the vehicle’ s powertrain system or its battery has just been serviced, the on-board diagnostics system is reset to a “not ready for I/M test” condition.
BRAKE FLUID The fluid level will drop slowly as the brakes wear , and will rise when the brake components are replaced. Fluid levels between the “MIN” and “MAX” lines are within the normal operating range; there is no need to add fluid.
7. Remove the dipstick and inspect the fluid level. The fluid should be in the designated areas for normal operating temperature. Low fluid level Do not drive the vehicle if the fluid level is at the bottom of the dipstick and the outside temperatures are above 50°F (10°C).
Do not use supplemental transmission fluid additives, treatments or cleaning agents. The use of these materials may affect transmission operation and result in damage to internal transmission components. AIR FILTER Refer to scheduled maintenance information for the appropriate intervals for changing the air filter element.
2. Loosen the hose clamp located closest to the air cleaner . 3. Remove the air cleaner assembly from the vehicle. 4. Release the two clamps that secure the cover to the air filter housing and place the cover aside. 5. Remove the air filter element from the air filter housing.
7. Install a new air filter element. Be careful not to crimp the filter element edges between the air filter housing and cover . 8. Replace the air filter housing cover and secure the clamps. Be sure all the tabs on the bottom edge are properly aligned.
10. Ensure the pads on the bottom of the air cleaner assembly are properly seated. 11. Reconnect the outlet tube to the air cleaner assembly and tighten the clamp. 12. Reconnect the Mass Air Flow Sensor electrical connector to the outlet tube. Make sure the locking tab on the connector is in “locked” position.
MOTORCRAFT PART NUMBERS Component 3.9L OHV V6 engine 4.2L OHV V6 engine Air filter element F A-1679 F A-1679 Battery BXT -59 BXT -59 BXT -65-750 BXT -65-750 Fuel filter FG-986B FG-986B Oil filter FL-400S FL-400S PCV valve 1 Spark plugs 2 1 The PCV valve is a critical emission component.
REFILL CAPACITIES Fluid Ford Part Name Application Capacity Brake fluid Motorcraft High Performance DOT 3 Motor V ehicle Brake Fluid 1 All Fill to MAX line on reservoir Engine oil (includes filter change) 3 Motorcraft SAE 5W -20 Premium Synthetic Blend Motor Oil (US) Motorcraft SAE 5W -20 Super Premium Motor Oil (Canada) 3.
LUBRICANT SPECIFICATIONS Item Ford part name Ford part number Ford specification Brake fluid Motorcraft High Performance DOT 3 Motor V ehicle Brake Fluid 1 PM-1 ESA-M6C25-A Door weatherstrips Silicone Spray Lubricant XL-6 ESR-M13P4-A Engine coolant Motorcraft Premium Gold Engine Coolant (yellow colored) VC-7-A (U.
Item Ford part name Ford part number Ford specification Door latch, hood latch, auxiliary hood latch, door and liftgate hinges, striker plates, seat tracks, sliding door both sides (upper and lower track) and fuel filler door hinge.
Item Ford part name Ford part number Ford specification W indshield washer fluid Motorcraft Premium W indshield W asher Concentrate ZC-32–A WSB-M8B16–A2 1 Use only brake fluids certified to meet Ford specifications. DOT 3 fluid is recommended. However , if DOT 3 is not available, DOT 4 fluid can be used.
1 4 2006 Freestar (win) Owners Guide (post-2002-fmt) USA (fus) Maintenance and Specifications 307.
IDENTIFYING YOUR VEHICLE Certification label The National Highway T raffic Safety Administration Regulations require that a Safety Compliance Certification Label be affixed to a vehicle and prescribe where the Safety Compliance Certification Label may be located.
The V ehicle Identification Number (VIN) contains the following information: 1. W orld manufacturer identifier 2. Brake type and Gross V ehicle W eight Rating (GVWR) 3. V ehicle line, series, body type 4. Engine type 5. Check digit 6. Model year 7. Assembly plant 8.
GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for your vehicle through your local authorized Ford or Ford of Canada dealer .
Rear seat entertainment systems - DVD Ash cup/coin holder T railer hitches, wiring harnesses and accessories Roof carriers Peace of mind First aid and safety kits Full vehicle covers Locking gas cap R.
A Accessory delay .......................... 65 AdvanceT rac .............................. 217 Air cleaner filter ...............298, 302 Air filter , cabin ............................ 42 Airbag supplemental restraint system ................148–149, 157, 159 and child safety seats .
wheels ...................................... 265 wiper blades ............................ 266 Clock ............................................ 63 Compass, electronic ....................56 calibration ................................. 57 set zone adjustment .
cap ........................................... 287 capacity ................................... 303 choosing the right fuel ........... 288 comparisons with EP A fuel economy estimates ................. 293 detergent in fuel ..................... 289 filling your vehicle with fuel .
headlamps, flash to pass .......... 45 instrument panel, dimming ..... 45 interior lamps ..................... 47–49 replacing bulbs ............. 49, 51–53 Lane change indicator (see T urn signal) ........................ 47 Liftgate ............
Safety belts (see Safety restraints) ..........134, 137, 139–141 Safety Canopy ........................... 159 Safety defects, reporting .......... 263 Safety restraints ........... 134, 137, 139–141 belt minder ............................. 143 extension assembly .
T urn signal .................................. 47 V V ehicle dimensions ................... 306 V ehicle Identification Number (VIN) .......................................... 308 V ehicle loading .......................... 200 V entilating your vehicle .
318.
319.
320.
Een belangrijk punt na aankoop van elk apparaat Ford 2006 Freestar (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Ford 2006 Freestar heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Ford 2006 Freestar vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Ford 2006 Freestar leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Ford 2006 Freestar krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Ford 2006 Freestar bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Ford 2006 Freestar kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Ford 2006 Freestar . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
