Gebruiksaanwijzing /service van het product 2008 E-150 van de fabrikant Ford
Ga naar pagina of 280
Introduction 4 Instrument Cluster 12 W arning lights and chimes 12 Gauges 17 Entertainment Systems 19 AM/FM stereo 19 AM/FM stereo with single CD 21 AM/FM stereo with in-dash six CD 25 Climate Control.
Seating and Safety Restraints 69 Seating 69 Safety restraints 76 Airbags 86 Child restraints 95 Tires, Wheels and Loading 1 12 T ire information 115 T ire inflation 116 T ire Pressure Monitoring Syste.
Maintenance and Specifications 229 Engine compartment 231 Engine oil 233 Battery 236 Engine coolant 238 Fuel information 244 Air filter(s) 261 Part numbers 263 Maintenance product specifications and capacities 264 Engine data 268 Accessories 272 Index 274 All rights reserved.
CALIFORNIA Proposition 65 W arning W ARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
SAFETY AND ENVIRONMENT PROTECTION W arning symbols in this guide How can you reduce the risk of personal injury to yourself or others? In this guide, answers to such questions are contained in comments highlighted by the warning triangle symbol. These comments should be read and observed.
SPECIAL NOTICES New V ehicle Limited W arranty For a detailed description of what is covered and what is not covered by your vehicle’ s New V ehicle Limited W arranty , refer to the Warranty Guide that is provided to you along with your Owner’ s Guide.
V ehicle Modification Data Recording Some aftermarket products may cause severe engine and/or transmission damage; refer to the What is not covered section in The new vehicle limited warranty for your vehicle chapter of your vehicle’ s W arranty Guide for more information.
Using your vehicle as an ambulance If your light truck is equipped with the Ford Ambulance Preparation Package, it may be utilized as an ambulance. Ford urges ambulance manufacturers to follow the rec.
Cell phone use The use of Mobile Communications Equipment has become increasingly important in the conduct of business and personal affairs. However , drivers must not compromise their own or others’ safety when using such equipment.
These are some of the symbols you may see on your vehicle. V ehicle Symbol Glossary Safety Alert See Owner’ s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat Lower Anchor Child Seat.
V ehicle Symbol Glossary Power W indows Front/Rear Power W indow Lockout Child Safety Door Lock/Unlock Interior Luggage Compartment Release Panic Alarm Engine Oil Engine Coolant Engine Coolant T emper.
W ARNING LIGHTS AND CHIMES W arning lights and gauges can alert you to a vehicle condition that may become serious enough to cause expensive repairs. A warning light may illuminate when a problem exists with one of your vehicle’ s functions. Many lights will illuminate when you start your vehicle to make sure the bulb works.
Under engine misfire conditions, excessive exhaust temperatures could damage the catalytic converter , the fuel system, interior floor coverings or other vehicle components, possibly causing a fire. Electronic throttle control: Illuminates when the engine has defaulted to a “limp-home” operation.
Anti-lock brake system: If the ABS light stays illuminated or continues to flash, a malfunction has been detected, have the system serviced immediately by your authorized dealer . Normal braking is still functional unless the brake warning light also is illuminated.
Low tire pressure warning (if equipped): Illuminates when your tire pressure is low . If the light remains ON at start up or while driving, the tire pressure should be checked. Refer to Inflating Y our T ires in the T ires, Wheels and Loading chapter .
Overdrive off: Illuminates when the overdrive function of the transmission has been turned off, refer to the Driving chapter . If the light does not illuminate, have the transmission serviced soon, or damage may occur . Charging system: Illuminates when the battery is not charging properly .
GAUGES Speedometer: Indicates the current vehicle speed. Engine coolant temperature gauge: Indicates engine coolant temperature. At normal operating temperature, the needle will be in the normal range (between “H” and “C”). If it enters the red section, the engine is overheating.
T rip odometer: Registers the miles (kilometers) of individual journeys. Press the SELECT/RESET control once to switch from the odometer to the trip odometer . Press the control again to select T rip A and T rip B features. T o reset the trip, press and hold the control again until the trip reading is 0.
AUDIO SYSTEMS AM/FM stereo (if equipped) Driving while distracted can result in loss of vehicle control, accident and injury . Ford strongly recommends that drivers use extreme caution when using any device that may take their focus off the road. The drivers primary responsibility is the safe operation of their vehicle.
3. AM/FM: Press to choose a frequency band in radio mode. 4. Memory preset buttons: T o set a station: Select frequency band AM/FM1/FM2; tune to a station, press and hold a preset button until sound returns. 5. Power/volume: Press to turn ON/OFF; turn to increase or decrease volume levels.
Satellite Compatible AM/FM Stereo In-Dash Single CD/MP3 Radio (if equipped) Driving while distracted can result in loss of vehicle control, accident and injury . Ford strongly recommends that drivers use extreme caution when using any device that may take their focus off the road.
TEXT is also available when equipped with Satellite radio. Y our radio comes equipped with Satellite ready capability . The kit to enable Satellite reception is available through your dealer . Detailed Satellite instructions are included with the dealer installed kit.
stored in preset 1 will begin playing. If there are less than six strong stations, the system will store the last one in the remaining presets. Setting the clock: Press MENU until SELECT HOUR or SELECT MINUTE is displayed. Use SEL to manually increase ( ) or decrease ( ) the hours/minutes.
18. Memory presets: T o set a station: Select frequency band; tune to a station, press and hold a preset button until sound returns. 19. Power/volume: Press to turn ON/OFF; turn to increase or decrease volume levels. 20. CD: Press to enter CD mode. CD units are designed to play commercially pressed 4.
For information regarding SIRIUS Satellite Radio, please call toll-free 888-539-SIRIUS (888-539-7474) or visit the SIRIUS website at www .siriusradio.com 24.
2. TEXT : The filename (Fi), song title (So), artist text (Ar) or album text (AL) may be viewed while playing an MP3 selection. When MP3 selection text is shown on the message display , its corresponding text indicator (Fi, So, Ar , or AL) is shown in the elapsed time display .
Fade: Press F ADE; then press SEL / to shift sound to the rear/front speakers. 9. Menu: Press to access the following functions: Compression: Brings soft and loud CD passages together for a more consistent listening level when in CD mode. Press MENU until compression status is displayed.
14. FF (Fast forward): In CD/MP3 mode, press until desired selection is reached. 15. REW (Rewind): In CD/MP3 mode, press until desired selection is reached. 16. SA T (if equipped): Y our radio comes equipped with Satellite Ready capability . The kit to enable the Satellite reception is available through your dealer .
CD units are designed to play commercially pressed 4.75 in (12 cm) audio compact discs only . Due to technical incompatibility , certain recordable and re-recordable compact discs may not function correctly when used in Ford CD players.
FM: 87.7, 87.9–107.7, 107.9 MHz Radio reception factors: There are three factors that can affect radio reception: • Distance/strength: The further you travel from an FM station, the weaker the signal and the weaker the reception.
HEATER ONLY SYSTEM (IF EQUIPPED) 1. Fan speed adjustment: Controls the volume of air circulated in the vehicle. 2. T emperature selection: Controls the temperature of the airflow in the vehicle. 3. Air flow selections: Controls the direction of the airflow in the vehicle.
MANUAL HEATING AND AIR CONDITIONING SYSTEM (IF EQUIPPED) 1. Fan speed adjustment: Controls the volume of air circulated in the vehicle. 2. T emperature selection: Controls the temperature of the airflow in the vehicle. 3. Air flow selections: Controls the direction of the airflow in the vehicle.
T o aid in side window defogging/demisting in cold weather: 1. Select MIX. 2. Set the temperature control to maintain comfort. 3. Set the fan speed to HI. Do not place objects on top of the instrument panel as these objects may become projectiles in a collision or sudden stop.
HEADLAMP CONTROL • The first position turns on the parking, tail, license plate and side marker lamps. • The outer position turns on the headlamps. Battery saver The battery saver can be set to turn off the courtesy lamps within 2 or 10 minutes if a door is left open and the key is not in the ignition.
Daytime running lamps (DRL) (if equipped) T urns the headlamps on with a reduced output. T o activate: • the ignition must be in the ON position and • the headlamp control is in the OFF or parking lamp position. Always remember to turn on your headlamps at dusk or during inclement weather .
P ANEL DIMMER CONTROL T o adjust the brightness of the instrument panel, rotate the dimmer control clockwise/counterclockwise when the headlamp control is in the parking lamp or low-beam position. T o turn on the interior lamps, rotate the dimmer control fully counterclockwise past the detent.
3. T urn on the low beam headlamps and open the hood. 4. Locate the high intensity area of the beam pattern and place the top edge of the intensity zone even with the horizontal reference line (4). If the top edge of the high intensity area is not even with the horizontal line, follow the next step to adjust it.
• (1) 8 feet (2.4 meters) • (2) Center height of lamp to ground • (3) 25 feet (7.6 meters) • (4) Horizontal reference line 2. Measure the height from the center of your headlamp (indicated by a 3.0 mm circle on the lens) to the ground and mark an 8 foot (2.
TURN SIGNAL CONTROL • Push down to activate the left turn signal. • Push up to activate the right turn signal. INTERIOR LAMPS Cargo and dome lamps with rear headliner Rear cargo lamps equipped wit.
Front and rear courtesy/reading lamps The dome portion of the lamp, the center light, can be turned on when the headlamp control is rotated fully counterclockwise or when any door is opened. The reading lamp portion, the two outer lights, can only be toggled on and off at the lamp.
Function Number of bulbs T rade number Side marker with sealed beam 2 194 Back-up lamps 2 3156K or 3156 License plate lamp 1 168 Stop/tail/turn/side marker lamp 2 3457K or 3357K High-mount brakelamp 2 912 Cargo lamp 1 211-2 Dome lamp (standard) 1 912 Map/reading lamp 2 211-2 All replacement bulbs are clear in color except where noted.
4. Remove the bulb assembly by turning it counterclockwise and pulling it straight out. Handle a halogen headlamp bulb carefully and keep out of children’ s reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hand could cause the bulb to break the next time the headlamps are operated.
Aerodynamic Sealed beam 3. Rotate the bulb socket counterclockwise and remove. 4. Carefully pull the bulb straight out of the socket. T o complete installation, follow the removal procedures in reverse order . Replacing side marker bulbs 1. Make sure the headlamp control is in the OFF position.
Sealed beam 3. Rotate the bulb socket counterclockwise and remove. 4. Carefully pull the bulb straight out of the socket. T o complete installation, follow the removal procedures in reverse order .
Replacing license plate lamp bulbs 1. T urn the headlamp switch to OFF and then remove the two screws and the license plate lamp assembly from the rear door . 2. Remove bulb socket from lamp assembly by turning counterclockwise. 3. Pull the bulb out from socket and push in the new bulb.
MULTI-FUNCTION LEVER W indshield wiper: Rotate the end of the control away from you to increase the speed of the wipers; rotate towards you to decrease the speed of the wipers. W indshield washer: Push the end of the stalk: • briefly: causes a single swipe of the wipers without washer fluid.
TILT STEERING WHEEL T o adjust the steering wheel: 1. Pull and hold the steering wheel release control toward you. 2. Move the steering wheel up or down until you find the desired location. 3. Release the steering wheel release control. This will lock the steering wheel in position.
Storage compartment (if equipped) Press the release on the door to open the storage compartment. The storage compartment may be used to secure sunglasses or a similar object. Installing a garage door opener (if equipped) The storage compartment can be converted to accommodate a variety of aftermarket garage door openers: 1.
Electronic compass/temperature display (if equipped) Outside air temperature The outside temperature display is contained in the overhead console. The temperature display can be turned off and on by pressing the SELECT control on the overhead console.
3. Press and hold the SELECT control until V AR appears in the display , then release. The display should show the current zone number . 4. Press the SELECT control until the desired zone number appears. The display will flash and then return to normal operation.
T o prevent the fuse from being blown, do not use the power point(s) over the vehicle capacity of 12 VDC/180W . If the power point or cigar lighter socket is not working, a fuse may have blown. Refer to Fuses and relays in the Roadside Emergencies chapter for information on checking and replacing fuses.
Press and hold the bottom part of the rocker switch to open the window . Press and hold the top part of the rocker switch to close the window . Accessory delay W ith accessory delay , the window switches and radio may be used for up to ten minutes after the ignition switch is turned to the OFF position, or until any door is opened.
Spotter mirror on standard mirror (if equipped) The spotter mirror only can be tilted from top to bottom. Move the lower mirror manually up/down to increase side and rear visibility . Apply pressure only in the center of the spotter mirror along the top or bottom edges to adjust the tilt feature.
The telescoping feature (if equipped) allows the mirror to extend approximately 3.15 inches (80 mm). This feature is especially useful to the driver when towing a trailer . SPEED CONTROL (IF EQUIPPED) W ith speed control set, you can maintain a set speed without keeping your foot on the accelerator pedal.
Resuming a set speed Press the RES (resume) control and release it. This will automatically return the vehicle to the previously set speed. Increasing speed while using speed control There are two ways to set a higher speed: • Press and hold the SET ACCEL control until you get to the desired speed, then release the control.
• Depress the brake pedal until the desired vehicle speed is reached, press the SET ACCEL control. Turning of f speed control There are two ways to turn off the speed control: • Depress the brake pedal. This will not erase your vehicle’ s previously set speed.
KEYS The key operates all locks on your vehicle. Y ou should always carry a second key with you in a safe place in case you require it in an emergency . If your vehicle is equipped with the SecuriLock™ Passive Anti-theft system, your keys are electronically coded to your vehicle; using a non-coded key will not permit your vehicle to start.
Deactivating/activating autolock feature Y our vehicle comes with the autolock feature disabled; there are two methods to enable/disable this feature: • Through your authorized dealer , or • by using a power door unlock/lock procedure.
Back cargo door lock (if equipped) The passenger side rear cargo door has a power door lock control mounted on the inside of the door . When this lock is pressed, all doors will lock/unlock. E-Guard Cargo Protection System™ (if equipped) The E-Guard Cargo Protection System™ insures that the cargo doors are double locked for extra security .
For vehicles equipped with manual door locks: • The front door locks can be locked by using either the key or the manual door lock. • In order to activate the E-Guard Cargo Protection System™, use the key or the manual door lock to lock the side and back cargo doors.
• The rear door handle is located in the rear door below the glass. T o open the side or back cargo doors from the inside: 1. Unlock the E-Guard Cargo Protection System™ using the emergency handle. 2. Unlatch the door using the inside release handle.
The remote entry system allows you to lock or unlock all vehicle doors without a key . Note: • The lock and unlock features work when the ignition is in any position. • The panic feature is active when the ignition is in either the 1 (ACCESSORY), 2 (LOCK) or 3 (OFF) positions.
flash twice to indicate that the vehicle has switched to one step unlocking. Repeat the procedure to switch back to two-step unlocking. Locking the doors 1. Press and release to lock all the doors. 2. Press and release again within three seconds to confirm that all the doors are closed and locked.
2. Do not wipe off any grease on the battery terminals on the back surface of the circuit board. 3. Remove the old battery . Note: Please refer to local regulations when disposing of transmitter batteries. 4. Insert the new battery . Refer to the diagram inside the remote entry transmitter for the correct orientation of the battery .
Note: Ensure the brake pedal is not depressed during this sequence. T o reprogram the remote entry transmitters: 1. Ensure the vehicle is electronically unlocked. 2. Place the key in the ignition and turn from the (2) LOCK position to (3) OFF . 3. Cycle eight times rapidly (within 10 seconds) between the (3) OFF position and (4) ON.
The inside lights will not turn off if: • they have been turned on with the dimmer control, or • any door is open. SECURILOCK™ PASSIVE ANTI-THEFT SYSTEM (IF EQUIPPED) SecuriLock™ passive anti-theft system is an engine immobilization system.
• When the igniton is in the 4 (ON) position, the indicator will glow for 3 seconds to indicate the engine is enabled. Automatic arming The vehicle is armed immediately after switching the ignition to the 2 (LOCK) position. Automatic disarming Switching the ignition to the 4 (ON) position with a coded key disarms the vehicle.
1. Insert the first previously programmed coded key into the ignition and turn the ignition from the 3 (OFF) position to the 4 (ON) position (maintain ignition in the 4 (ON) position for at least one second, but no more than ten seconds).
SEATING Notes: Reclining the seatback can cause an occupant to slide under the seat’ s safety belt, resulting in severe personal injuries in the event of a collision. Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop.
Pull lever up to adjust seatback. Before returning the seatback to its original position, make sure that cargo or any objects are not trapped behind the seatback. After returning the seatback to its original position, pull on the seatback to ensure that it has fully latched.
Press to raise or lower the rear portion of the seat cushion. Press the control to move the seat forward, backward, up or down. REAR SEATS Rear captains chair adjust — passenger side only Pull the lever forward to adjust the seat forward or backward.
Quick release captains chair (7 passenger configuration second row only) T o remove the seat: 1. Disengage the lap/shoulder belt from the seat by inserting a key or small screwdriver into the slot in the detachable anchor and lifting upward.
1. Position the seat to the floor mount. 2. Pull the seat latch handle downward to lock the seat in position. 3. Make sure the safety belt is not twisted, then insert the safety belt tongue into detachable anchor until you hear a “click” and feel the latch engage.
2. Find the clips attached near the ends of the lap/shoulder belts. 3. Clip the end of the belt to the stationary portion of the shoulder belt coming out of the trim panel. The end of the shoulder belt must be clipped in order to keep it from striking anything during vehicle operation.
4. W ith assistance, pull the LH/RH seat latch release straps (1) (located behind the latch mechanisms) to release the latch from the rear strikers. 5. Lift the rear end of seat upward and rearward by pushing on the seatback (2) and lifting the seat cushion (3) to disengage the front seat hook and the rear seat latch from the striker .
5. After the front LH/RH hooks are engaged to the LH/RH front striker pins, pull LH/RH seat latch release straps to allow engagement of the latch to the striker pins. Refer to the illustration in T o remove the rear seats above. 6. Pull/push seat back forward/backward to check for proper seat installation.
In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a safety belt. Each seating position in your vehicle has a specific safety belt assembly which is made up of one buckle and one tongue that are designed to be used as a pair .
• Front and rear seats All safety restraints in the vehicle are combination lap and shoulder belts. All of the passenger combination lap and shoulder belts have two types of locking modes described .
How to use the automatic locking mode • Buckle the combination lap and shoulder belt. • Grasp the shoulder portion and pull downward until the entire belt is pulled out. • Allow the belt to retract. As the belt retracts, you will hear a clicking sound.
BEL T AND RETRACTOR ASSEMBL Y MUST BE REPLACED if the safety belt assembly “automatic locking retractor” feature or any other safety belt function is not operating properly when checked by an authorized dealer . Failure to replace the Belt and Retractor assembly could increase the risk of injury in collisions.
Safety belt warning light and indicator chime The safety belt warning light illuminates in the instrument cluster and a chime sounds to remind the occupants to fasten their safety belts. Conditions of operation If... Then... The driver’ s safety belt is not buckled before the ignition switch is turned to the ON position.
If... Then... The driver’ s safety belt is not buckled approximately 5 seconds after the safety belt warning light has turned off... The Belt-Minder 威 feature is activated - the safety belt warnin.
Reasons given... Consider ... “I was in a hurry” Prime time for an accident. Belt-Minder 威 reminds us to take a few seconds to buckle up. “Safety belts don’t work” Safety belts, when used properly , reduce risk of death to front seat occupants by 45% in cars, and by 60% in light trucks.
Deactivating/activating the Belt-Minder 姞 feature Read Step s1-5 thoroughly before proceeding with the deactivation/activation programming procedure.
• This will enable the Belt-Minder 威 feature for that seating position if it is currently disabled. As confirmation, the safety belt warning light will flash four times per second for three second.
Failure to inspect and if necessary replace the safety belt assembly under the above conditions could result in severe personal injuries in the event of a collision.
Always transport children 12 years old and under in the back seat and always properly use appropriate child restraints. Never place a rear -facing child seat in front of an active airbag. If you must transport a forward-facing child in the front seat, move the seat all the way back and use appropriate restraints.
Children and airbags Children must always be properly restrained. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position. Failure to follow these instructions may increase the risk of injury in a collision.
The airbags inflate and deflate rapidly upon activation. After airbag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder or sodium compounds which may irritate the skin and eyes, but none of the residue is toxic.
Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a tone to indicate the condition of the system. Refer to Airbag readiness section in the Instrument Cluster chapter . Routine maintenance of the airbag is not required.
Passenger airbag ON/OFF switch (if equipped) Note : The passenger airbag ON/OFF switch (if equipped) may be on vehicles with no rear seats and a gross vehicle weight rating (GVWR) greater than 8500. See V ehicle loading – with and without a trailer in the T ires, Wheels and loading chapter .
In order to avoid inadvertent activation of the switch, always remove the ignition key from the passenger air bag ON/OFF switch. An infant in a rear -facing seat faces a high risk of serious or fatal injuries from a deploying passenger airbag.
If your vehicle has rear seats, always transport children who are 12 and younger in the rear seat. Always use safety belts and child restraints properly . DO NOT place a child in a rear facing infant seat in the front seat unless your vehicle is equipped with an airbag ON/OFF switch and the passenger airbag is turned OFF .
• the child has a medical condition which, according to the child’ s physician, makes it necessary for the child to ride in the front seat so that the driver can constantly monitor the child’ s condition.
• the child has a medical condition that, according to the child’ s physician, makes it necessary for the child to ride in the front seat so that the driver can monitor the child’ s condition.
Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision. Always follow the instructions and warnings that come with any infant or child restraint you might use.
Do not leave children, unreliable adults, or pets unattended in your vehicle. Child booster seats Children outgrow a typical convertible or toddler seat when they weigh 40 lb.
T ypes of booster seats There are two types of belt-positioning booster seats: • Those that are backless. If your backless booster seat has a removable shield, remove the shield and use the lap/shoulder belt.
Children and booster seats vary widely in size and shape. Choose a booster that keeps the lap belt low and snug across the hips, never up across the stomach, and lets you adjust the shoulder belt to cross the chest and rest snugly near the center of the shoulder .
Never use pillows, books, or towels to boost a child. They can slide around and increase the likelihood of injury or death in a collision. SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of the child.
Ford recommends the use of a child safety seat having a top tether strap. Install the child safety seat in a seating position with LA TCH and tether anchors. For more information on top tether straps and anchors, refer to Attaching safety seats with tether straps in this chapter .
2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together . 3. While holding the shoulder and lap belt portions together , route the tongue through the child seat according to the child seat manufacturer’ s instructions.
5. T o put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is extracted. 6. Allow the belt to retract. The belt will click as it retracts to indicate it is in the automatic locking mode.
Attaching safety seats with tether straps Children should be placed in the rear in an appropriate child safety seat that is properly secured to the vehicle.
1. Position the child safety seat on the front right-hand passenger seat. 2. Adjust the front right-hand passenger seat full forward. 3. Route the child safety seat tether strap over the back of the front right-hand passenger seat as shown. 4. Clip the tether strap hook to the seat pedestal to the location shown.
5. Adjust the front right hand passenger seat to the full rearward position. 6. Install the child safety seat tightly using the LA TCH anchors or safety belts. Follow the instructions in this chapter . 7. T ighten the child safety seat tether strap according to the manufacturer’ s instructions.
1. Position the child safety seat on the second row left hand or right hand bucket seat. 2. Route the child safety tether strap over the back of the left hand or right hand second row bucket seat. 3. Clip the tether strap hook to the seat pedestal at the location shown.
2. Route the child safety tether strap over the back of the bench seat. 3. Clip the center tether strap hook to the tether bracket mounted under rear rail of seat cushion frame. Clip the outboard tether strap hooks to the tether bracket slot provided on the left side of each seat pedestal.
• Five passenger crew van • Seven passenger wagon • Eight passenger wagon • T welve passenger wagon 2008 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus) Seating and Safety Restraints 10.
• Fifteen passenger wagon represents LA TCH anchors. represents tether strap anchors. Never attach two LA TCH child safety seats to the same anchor . In a crash, one anchor may not be strong enough to hold two child safety seat attachments and may break, causing serious injury or death.
Each time you use the safety seat, check that the seat is properly attached to the lower anchors and tether anchor . T ry to tilt the child seat from side to side.
NOTICE TO UTILITY VEHICLE AND TRUCK OWNERS Utility vehicles and trucks handle differently than passenger cars in the various driving conditions that are encountered on streets, highways and off-road.
VEHICLE CHARACTERISTICS How your vehicle differs from other vehicles SUV and trucks can differ from some other vehicles in a few noticeable ways. Y our vehicle may be: • Higher – to allow higher load carrying capacity and to allow it to travel over rough terrain without getting hung up or damaging underbody components.
INFORMA TION ABOUT UNIFORM TIRE QUALITY GRADING T ire Quality Grades apply to new pneumatic passenger car tires. The Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width.
The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics.
• PSI: Pounds per square inch, a standard unit of air pressure. • Cold inflation pressure: The tire pressure when the vehicle has been stationary and out of direct sunlight for an hour or more and prior to the vehicle being driven for 1 mile (1.6 km).
Under -inflation is the most common cause of tire failures and may result in severe tire cracking, tread separation or ⬙ blowout ⬙ , with unexpected loss of vehicle control and increased risk of injury . Under -inflation increases sidewall flexing and rolling resistance, resulting in heat buildup and internal damage to the tire.
Note: If you have to drive a distance to get air for your tire(s), check and record the tire pressure first and add the appropriate air pressure when you get to the pump. It is normal for tires to heat up and the air pressure inside to go up as you drive.
Tire inflation information All tires with Steel Carcass Plies (if equipped): This type of tire utilizes steel cords in the sidewalls. As such, they cannot be treated like normal light truck tires.
Stay out of the trajectory (1) as indicated in the illustration. TIRE CARE Inspecting your tires Periodically inspect the tire treads for uneven or excessive wear and remove objects such as stones, nails or glass that may be wedged in the tread grooves.
Improper or inadequate vehicle maintenance can cause tires to wear abnormally . Inspect all your tires, including the spare, frequently , and replace them if one or more of the following conditions ex.
U.S. DOT Tire Identification Number (TIN) Both U.S. and Canada Federal regulations require tire manufacturers to place standardized information on the sidewall of all tires. This information identifies and describes the fundamental characteristics of the tire and also provides a U.
When mounting replacement tires and wheels, you should not exceed the maximum pressure indicated on the sidewall of the tire to set the beads without additional precautions listed below . If the beads do not seat at the maximum pressure indicated, re-lubricate and try again.
• Do not run over curbs or hit the tire against a curb when parking If your vehicle is stuck in snow , mud, sand, etc., do not rapidly spin the tires; spinning the tires can tear the tire and cause an explosion. A tire can explode in as little as three to five seconds.
• Rear Wheel Drive (RWD) vehicles/Four Wheel Drive (4WD)/ All Wheel Drive (A WD) vehicles (front tires at top of diagram) Sometimes irregular tire wear can be corrected by rotating the tires.
• DRW – Six tire rotation If your vehicle is equipped with dual rear wheels it is recommended that the front and rear tires (in pairs) be rotated only side to side. W e do not recommend splitting up the dual rear wheels. Rotate them side to side as a set/pair .
Information on “P” type tires P215/65R15 95H is an example of a tire size, load index and speed rating. The definitions of these items are listed below . (Note that the tire size, load index and speed rating for your vehicle may be different from this example.
Note: Y ou may not find this information on all tires because it is not required by federal law . Letter rating Speed rating - mph (km/h) M 81 mph (130 km/h) N 87 mph (140 km/h) Q 99 mph (159 km/h) R .
12. T readwear , T raction and T emperature Grades • T readwear: The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course.
Additional information contained on the tire sidewall for “L T” type tires “L T” type tires have some additional information beyond those of “P” type tires; these differences are described below: 1. LT: Indicates a tire, designated by the T ire and Rim Association (T&RA), that is intended for service on light trucks.
Information on “T” type tires “T” type tires have some additional information beyond those of “P” type tires; these differences are described below: T145/80D16 is an example of a tire size. Note: The temporary tire size for your vehicle may be different from this example.
TIRE PRESSURE MONITORING SYSTEM (TPMS) (IF EQUIPPED) Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label.
The T ire Pressure Monitoring System complies with part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Understanding your Tire Pressure Monitoring System (TPMS) The T ire Pressure Monitoring System measures pressure in your four road tires and sends the tire pressure readings to your vehicle. The Low T ire W arning Lamp will turn ON if the tire pressure is significantly low .
Low T ire Pressure W arning Light Possible cause Customer Action Required Solid W arning Light T ire(s) under -inflated 1. Check your tire pressure to ensure tires are properly inflated; refer to Inflating your tires in this chapter .
Low T ire Pressure W arning Light Possible cause Customer Action Required Flashing W arning Light Spare tire in use Y our temporary spare tire is in use.
tires are flat, repair as necessary . Check air pressure in the road tires. If any tire is under -inflated, carefully drive the vehicle to the nearest location where air can be added to the tires. Inflate all the tires to the recommended inflation pressure.
TPMS reset tool A special TPMS reset tool has been provided with your vehicle to reset your TPMS after tire rotation. The tool is located with your Owner’ s Guide materials. Please take the tool with the provided V elcro 威 strip on the back and mount it in the bottom right corner of your Owner’ s Guide case (as shown) for safe keeping.
3. Press and hold the brake pedal for two (2) seconds, then release. 4. T urn the ignition to OFF/LOCK ( DO NOT remove the key .) 5. Cycle the ignition from OFF/LOCK to RUN three (3) times ending in RUN.
1. Left front tire: Place the TPMS reset tool against the left front tire where the tire meets the rim, opposite from the valve stem (1) as shown. This is where the sensor is located inside the rim.
Rotation, pressure adjustment and TPMS reset example The following example describes all the major steps involved in rotating tires on a vehicle with different front and rear tire pressures. It illustrates that the TPMS reset procedure needs to follow tire rotation and pressure adjustment to avoid a possible false low tire warning.
Sensor position following tire rotation Sensor 1: 50 psi Sensor 2: 50 psi Sensor 3: 80 psi Sensor 4: 80 psi Pressure adjustment without the required TPMS reset procedure Sensor 1: 80 psi Sensor 2: 80 psi Sensor 3: 50 psi Sensor 4: 50 psi In this situation, the TPMS warning light will come on.
Rotation, pressure adjustment and successful completion of the TPMS reset procedure Sensor 1: 80 psi Sensor 2: 80 psi Sensor 3: 50 psi Sensor 4: 50 psi T ire rotation and air pressure adjustment follo.
V EHICLE LOADING – WITH AND WITHOUT A TRAILER This section will guide you in the proper loading of your vehicle and/or trailer , to keep your loaded vehicle weight within its design rating capability , with or without a trailer . Properly loading your vehicle will provide maximum return of vehicle design performance.
Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be found on the T ire Label on the B-Pillar or the edge of the driver’ s door (vehicles exported outside the US and Canada may not have a T ire Label).
Example only: Cargo W eight – includes all weight added to the Base Curb W eight, including cargo and optional equipment. When towing, trailer tongue load or king pin weight is also part of cargo weight. GA W (Gross Axle W eight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload.
GA WR (Gross Axle W eight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Label located on the B-Pillar or the edge of the driver’ s door .
GCW (Gross Combined W eight) – is the weight of the loaded vehicle (GVW) plus the weight of the fully loaded trailer . GCWR (Gross Combined W eight Rating) – is the maximum allowable weight of the vehicle and the loaded trailer – including all cargo and passengers – that the vehicle can handle without risking damage.
Exceeding any vehicle weight rating limitation could result in serious damage to the vehicle and/or personal injury . Steps for determining the correct load limit: 1. Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lb.
to transport the cement to your home? If you and your friend each weigh 220 lb. (99 kg), the calculation would be: 1400 - (2 x 220) - (12 x 100) = 1400 - 440 - 1200 = - 240 lb.
GCWR (Gross Combined W eight Rating)/T railer W eights Engine Rear axle ratio Maximum GCWR - lb. (kg) Maximum Loaded T railer W eight - lb. (kg) Maximum frontal area of trailer - ft 2 (m 2 ) E-150 Regular/R V V an (8520 GVWR) 4.6L 3.73 11500 (5216) 6000 (2722) 60 (5.
GCWR (Gross Combined W eight Rating)/T railer W eights Engine Rear axle ratio Maximum GCWR - lb. (kg) Maximum Loaded T railer W eight - lb. (kg) Maximum frontal area of trailer - ft 2 (m 2 ) E-250 Extended/R V V an (8900 GVWR) 4.6L 3.73 11500 (5216) 5900 (2676) 60 (5.
GCWR (Gross Combined W eight Rating)/T railer W eights Engine Rear axle ratio Maximum GCWR - lb. (kg) Maximum Loaded T railer W eight - lb. (kg) Maximum frontal area of trailer - ft 2 (m 2 ) E-350 Extended/R V V an (9500 GVWR) 5.4L 3.73 13000 (5897) 7200 (3266) 60 (5.
GCWR (Gross Combined W eight Rating)/T railer W eights Engine Rear axle ratio Maximum GCWR - lb. (kg) Maximum Loaded T railer W eight - lb. (kg) Maximum frontal area of trailer - ft 2 (m 2 ) E-350 Cutaway (158” wheelbase, dual rear wheel) (10000 GVWR) 5.
GCWR (Gross Combined W eight Rating)/T railer W eights Engine Rear axle ratio Maximum GCWR - lb. (kg) Maximum Loaded T railer W eight - lb. (kg) Maximum frontal area of trailer - ft 2 (m 2 ) E-350 Stripped Chassis (158” wheelbase, single rear wheel) (9600 GVWR) 5.
GCWR (Gross Combined W eight Rating)/T railer W eights Engine Rear axle ratio Maximum GCWR - lb. (kg) Maximum Loaded T railer W eight - lb. (kg) Maximum frontal area of trailer - ft 2 (m 2 ) E-450 Cutaway (158” wheelbase, dual rear wheel) (14050 GVWR) 5.
GCWR (Gross Combined W eight Rating)/T railer W eights Engine Rear axle ratio Maximum GCWR - lb. (kg) Maximum Loaded T railer W eight - lb. (kg) Maximum frontal area of trailer - ft 2 (m 2 ) For high altitude operation reduce GCWR by 2% per 1,000 ft. (300 meters) elevation.
If you use a rental trailer , follow the instructions that the rental agency gives to you. Do not attach safety chains to the bumper . T railer brakes Electric brakes and manual, automatic or surge-type trailer brakes are safe if installed properly and adjusted to the manufacturer’ s specifications.
• Consult your local motor vehicle speed regulations for towing a trailer . • T o eliminate excessive shifting, use a lower gear . This will also assist in transmission cooling. • Anticipate stops and brake gradually . When descending long, steep downhill grades, always use a lower gear to provide engine braking to save wear on brakes.
Launching or retrieving a boat Disconnect the wiring to the trailer before backing the trailer into the water . Reconnect the wiring to the trailer after the trailer is removed from the water . When backing down a ramp during boat launching or retrieval: • do not allow the static water level to rise above the bottom edge of the rear bumper .
STARTING Positions of the ignition 1. ACCESSORY , allows the electrical accessories such as the radio to operate while the engine is not running. 2. LOCK, locks the automatic transmission gearshift lever and allows key removal. 3. OFF , shuts off the engine and all accessories without locking the steering wheel.
If you smell exhaust fumes inside your vehicle, have your dealer inspect your vehicle immediately . Do not drive if you smell exhaust fumes. Important safety precautions When the engine starts, the idle RPM runs faster to warm the engine. If the engine idle speed does not slow down automatically , have the vehicle checked.
• T urn the key to 4 (ON) without turning the key to 5 (ST ART). Some warning lights will briefly illuminate. See W arning lights and chimes in the Instrument Cluster chapter for more information regarding the warning lights. Starting the engine 1. T urn the key to 4 (ON) without turning the key to 5 (ST ART).
Important ventilating information If the engine is idling while the vehicle is stopped for a long period of time, open the windows at least one inch (2.
• T o reduce the risk of electrical shock, do not use your heater with ungrounded electrical systems or two pronged (cheater) adapters. Also ensure that the block heater , especially the cord, is in good condition before use.
Refer to Brake system warning light in the Instrument Cluster chapter for information on the brake system warning light. Four-wheel anti-lock brake system (ABS) Y our vehicle is equipped with an Anti-lock Braking System (ABS). This system helps you maintain steering control during emergency stops by keeping the brakes from locking.
Parking brake T o set the parking brake (1), press the parking brake pedal down until the pedal stops. T o release, pull the lever (2). Always set the parking brake fully and make sure that the gearshift is securely latched in P (Park). The BRAKE warning lamp will illuminate and will remain illuminated until the parking brake is released.
Aggressive driving in any road conditions can cause you to lose control of your vehicle increasing the risk of severe personal injury or property damage.
If the AdvanceT rac 威 with RSC system is activated excessively in a short period of time, the brake portion of the system will shut down to allow the brakes to cool down. A limited AdvanceT rac 威 with RSC function using only engine power reduction will still help control the wheels from over -spinning.
• Cornering while towing a heavily loaded trailer (refer to T railer towing in the T ires, Wheels and Loading chapter .) The RSC system works in conjunction with the AdvanceT rac 威 system to further enhance the vehicle’ s overall stability during aggressive maneuvers.
vehicle is stuck in snow or mud or when driving in deep sand, switching off the AdvanceT rac 威 with RSC system may be beneficial so the wheels are allowed to spin.
• Heavy or uneven steering efforts may be caused by low power steering pump fluid level. Check for low power steering pump fluid level before seeking service by your authorized dealer . • Do not fill the power steering pump reservoir above the MAX mark on the reservoir , as this may result in leaks from the reservoir .
Loaded vehicles, with a higher center of gravity , may handle differently than unloaded vehicles. Do not overload your vehicle and use extra precautions, such as driving at slower speeds, avoiding abrupt steering changes and allowing for increased stopping distance, when driving a heavily loaded vehicle.
• In the event of an emergency stop, avoid skidding the tires and do not attempt any sharp steering wheel movements. V ehicles with a higher center of gravity such as utility and four -wheel drive vehicles handle differently than vehicles with a lower center of gravity .
Always set the parking brake fully and make sure the gearshift is latched in P (Park). T urn the ignition to the LOCK position and remove the key whenever you leave your vehicle. If the parking brake is fully released, but the brake warning lamp remains illuminated, the brakes may not be working properly .
Always set the parking brake fully and make sure the gearshift is latched in P (Park). T urn the ignition to the LOCK position and remove the key whenever you leave your vehicle. R (Reverse) W ith the gearshift lever in R (Reverse), the vehicle will move backward.
2 (Second) This position allows for second gear only . • Provides engine braking. • Use to start-up on slippery roads. • T o return to (Overdrive), move the gearshift lever into the (Overdrive) position. • Selecting 2 (Second) at higher speeds will cause the transmission to downshift to second gear at the appropriate vehicle speed.
P (Park) This position locks the transmission and prevents the rear wheels from turning. T o put your vehicle in gear: • Start the engine • Depress the brake pedal • Move the gearshift lever int.
The TOW HAUL indicator light will illuminate in the instrument cluster . T ow/Haul delays upshifts to reduce frequency of transmission shifting. T ow/Haul also provides engine braking in all forward g.
• Depress the accelerator to the floor . • Allows transmission to select an appropriate gear . Understanding the shift positions of the 5–speed automatic transmission (if equipped - diesel engines only) P (Park) This position locks the transmission and prevents the rear wheels from turning.
D (Drive) without Overdrive D (Drive) without Overdrive can be activated by pressing the transmission control switch (TCS) on the end of the gearshift lever . • This position allows for all forward gears except overdrive. • The O/D OFF lamp will illuminate in the instrument cluster .
If your vehicle goes off the edge of the pavement • If your vehicle goes off the edge of the pavement, slow down, but avoid severe brake application, ease the vehicle back onto the pavement only after reducing your speed. Do not turn the steering wheel too sharply while returning to the road surface.
T o help avoid personal injury , always use caution when in reverse and when using the RSS. This system is not designed to prevent contact with small or moving objects. The system is designed to provide a warning to assist the driver in detecting large stationary objects to avoid damaging the vehicle.
The RSS automatically turns on when the gearshift lever is placed in R (Reverse) and the ignition is ON. An RSS control allows the driver to turn the RSS on and off. T o turn the RSS off, the ignition must be ON, and the gear selector in R (Reverse). An indicator light on the control will illuminate when the system is turned off.
DRIVING THROUGH WATER If driving through deep or standing water is unavoidable, proceed very slowly especially when the depth is not known. Never drive through water that is higher than the bottom of the wheel rims (for cars) or the bottom of the hubs (for trucks).
ROADSIDE ASSISTANCE Getting roadside assistance T o fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program.
Canadian customers refer to your Customer Information Guide for information on: • coverage period • exact fuel amounts • towing of your disabled vehicle • emergency travel expense reimbursemen.
HAZARD FLASHER CONTROL The hazard flasher is located on the steering column, just behind the steering wheel. The hazard flashers will operate when the ignition is in any position or if the key is not in the ignition. Push in the flasher control and all front and rear direction signals will flash.
Except for commercial stripped chassis vehicles, this switch is located in the front passenger’ s footwell, by the kick panel. On commercial stripped chassis vehicles, this switch is located on a bracket above the brake pedal. T o reset the switch: 1.
FUSES AND RELAYS Fuses If electrical components in the vehicle are not working, a fuse may have blown. Blown fuses are identified by a broken wire within the fuse. Check the appropriate fuses before replacing any electrical components. Note: Always replace a fuse with one that has the specified amperage rating.
T o remove a fuse use the fuse puller tool provided on the fuse panel cover . The fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 1 — Not.
Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 8 15A Radio capacitor(s), Ignition coils, PCM (Powertrain Control Module) relay 9 5A W iper control module 10 20A Main .
Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 29 10A Diagnostics 30 15A Headlamps (high beam indicator), DRL 31 10A Right headlamp (low beam) 32 20A Power point #1 (.
If the battery has been disconnected and reconnected, refer to the Battery section of the Maintenance and Specifications chapter . The high-current fuses are coded as follows.
Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 10 30A** T railer tow electric brake controller 11 60A** 4-Wheel Anti-lock Brake System (4W ABS) 40A** AdvanceT rac 威 with RSC .
Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 28 — Not used A — Fuel pump relay B — Horn relay C — T railer back-up lamps relay D — T railer running lamps relay E .
The relays are coded as follows: Relay location Description 1 Interior lamps 2 Open 3 Open 4 Battery saver Engine compartment relay module The engine compartment relay module is located in one of two .
CHANGING THE TIRES If you get a flat tire while driving, do not apply the brake heavily . Instead, gradually decrease your speed. Hold the steering wheel firmly and slowly move to a safe place on the side of the road. Note: The tire pressure monitoring system (TPMS) indicator light will illuminate when the spare tire is in use.
When driving with one of the dissimilar spare tires listed above, do not: • Exceed 50 mph (80 km/h) • Load the vehicle beyond maximum vehicle load rating listed on the Safety Compliance Label • .
When driving with the full-size dissimilar spare tire/wheel additional caution should be given to: • T owing a trailer • Driving vehicles equipped with a camper body • Driving vehicles with a load on the cargo rack Drive cautiously when using a full-size dissimilar spare tire/wheel and seek service as soon as possible.
T o remove the spare tire: 1. Open the rear doors and remove the thumb screw and anti-theft bracket. If finger pressure will not remove the thumb screw , use the lug wrench to loosen the screw .
1. Block the wheel that is diagonally opposite the tire you are changing. On E-450 vehicles, the parking brake is on the transmission. Therefore, the vehicle will not be prevented from moving when a rear wheel is lifted, even if the parking brake is applied.
T o lessen the risk of personal injury , do not put any part of your body under the vehicle while changing a tire. Do not start the engine when your vehicle is on the jack. The jack is only meant for changing the tire. 2. Position the jack to raise the front or rear wheel.
Front axle jacking points: Place the jack under the pin on the front surface of the front axle. Do not place the jack under or on the steering linkage. • Raise the jack until the wheel is completely off the ground. (T urn jack handle clockwise if your vehicle is equipped with a screw-type jack or pump the jack if equipped with a hydraulic jack.
Never use wheels or lug nuts different than the original equipment as this could damage the wheel or mounting system. This damage could allow the wheels to come off while the vehicle is being driven. 6. Install any wheel covers, ornaments or hub caps.
4. Check that the tire lies flat against the frame and is properly tightened. T ry to push or pull, then turn the tire to be sure it will not move. Loosen and retighten, if necessary . Failure to properly stow the spare tire may result in failure of the winch cable and loss of the tire.
When a wheel is installed, always remove any corrosion, dirt or foreign materials present on the mounting surfaces of the wheel or the surface of the wheel hub, brake drum or brake disc that contacts the wheel. Ensure that any fasteners that attach the rotor to the hub are secured so they do not interfere with the mounting surfaces of the wheel.
Preparing your vehicle When the battery is disconnected or a new battery is installed, the automatic transmission must relearn its shift strategy . As a result, the transmission may have firm and/or soft shifts. This operation is considered normal and will not affect function or durability of the transmission.
2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery . 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery .
4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’ s engine, away from the battery and the carburetor/fuel injection system. Do not use fuel lines, engine rocker covers or the intake manifold as grounding points.
Removing the jumper cables Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the ground metal surface. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery .
3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’ s battery . 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’ s battery .
WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or , if you are a member of a roadside assistance program, your roadside assistance service provider . Ford recommends your vehicle be towed with a wheel lift or flatbed.
GETTING THE SERVICES YOU NEED At home Y ou must take your Ford vehicle to an authorized dealer for warranty repairs. While any authorized dealer handling your vehicle line will provide warranty service, we recommend you return to your selling authorized dealer who wants to ensure your continued satisfaction.
In Canada: Customer Relationship Centre Ford Motor Company of Canada, Limited P .O. Box 2000 Oakville, Ontario L6J 5E4 1-800-565-3673 (FORD) www .ford.
In the United States, a warranty dispute must be submitted to the BBB AUTO LINE before taking action under the Magnuson-Moss W arranty Act, or to the extent allowed by state law , before pursuing replacement or repurchase remedies provided by certain state laws.
THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM (U.S. ONLY) Y our satisfaction is important to Ford Motor Company and to your dealer . Experience has shown that our customers have been very successful in achieving satisfaction by following the three-step procedure outlined on the front page of the W arranty Guide.
UTILIZING THE MEDIATION/ARBITRATION PROGRAM (CANADA ONLY) For vehicles delivered to authorized Canadian dealers. In those cases where you continue to feel that the efforts by Ford of Canada and the au.
If you did not take advantage of the Ford Extended Service Plan at the time of purchasing your vehicle, you may still be eligible. Since this information is subject to change, please ask your authorized dealer for complete details about Ford Extended Service Plan coverage options, or visit the Ford ESP website at www .
ORDERING ADDITIONAL OWNER’S LITERA TURE T o order the publications in this portfolio, contact Helm, Incorporated at: HELM, INCORPORA TED P .O. Box 07150 Detroit, Michigan 48207 Or call: For a free publication catalog, order toll free: 1-800-782-4356 Monday-Friday 8:00 a.
T o contact NHTSA, you may call the V ehicle Safety Hotline toll-free at 1–888–327–4236 (TTY : 1–800–424–9153); go to http://www.safercar .gov; or write to: Administrator NHTSA 400 Seventh Street, SW W ashington, D.C. 20590 Y ou can also obtain other information about motor vehicle safety from http://www.
W ASHING THE EXTERIOR W ash your vehicle regularly with cool or lukewarm water and a neutral pH shampoo, such as Motorcraft Detail W ash (ZC-3-A), which is available from your authorized dealer . • Never use strong household detergents or soap, such as dish washing or laundry liquid.
• After polishing chrome bumpers, apply a coating of Motorcraft Premium Liquid W ax (ZC-53-A), available from your authorized dealer , or an equivalent quality product to help protect from environmental effects.
• Some automatic car washes may cause damage to the finish on your wheel rims or covers. Chemical-strength cleaners, or cleaning chemicals, in combination with brush agitation to remove brake dust and dirt, could wear away the clearcoat finish over time.
PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products are available from your authorized dealer . • For routine cleaning, use Motorcraft Detail W ash (ZC-3-A). • If tar or grease spots are present, use Motorcraft Bug and T ar Remover (ZC-42).
INSTRUMENT PANEL/INTERIOR TRIM AND CLUSTER LENS Clean the instrument panel, interior trim areas and cluster lens with a clean and damp white cotton cloth, then with a clean and dry white cotton cloth; you may also use Motorcraft Dash & Vinyl Cleaner (ZC-38-A) on the instrument panel and interior trim areas.
• If a ring forms on the fabric after spot cleaning, clean the entire area immediately (but do not oversaturate) or the ring will set. • Do not use household cleaning products or glass cleaners, which can stain and discolor the fabric and affect the flame retardant abilities of the seat materials.
Motorcraft Multi-Purpose Cleaner (Canada only) (CXC-101) Motorcraft Custom Bright Metal Cleaner (ZC-15) Motorcraft Custom Clear Coat Polish (ZC-8-A) Motorcraft Custom Vinyl Protectant (U.S. only) (ZC-40-A) Motorcraft Dash and Vinyl Cleaner (ZC-38-A) Motorcraft Deluxe Leather and Vinyl Cleaner (U.
SERVICE RECOMMENDATIONS T o help you service your vehicle, we provide scheduled maintenance information which makes tracking routine service easy . If your vehicle requires professional service, your authorized dealer can provide the necessary parts and service.
OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the bottom left corner of the instrument panel. 2. Go to the front of the vehicle and push the auxiliary latch, located in the center top of the grill, to the left to release the hood.
IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT Engine compartment component locations Refer to the 6.0L and 6.4L Power Stroke Direct Injection T urbo Diesel Owner’ s Guide Supplement for diesel engine component locations. 1. W indshield washer fluid reservoir 2.
WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if the level is low . In very cold weather , do not fill the reservoir completely . Only use a washer fluid that meets Ford specification WSB-M8B16-A2. Do not use any special washer fluid such as windshield water repellent type fluid or bug wash.
Poor wiper quality can be improved by cleaning the wiper blades and the windshield, refer to Windows and wiper blades in the Cleaning chapter . T o prolong the life of the wiper blades, it is highly recommended to scrape off the ice on the windshield before turning on the wipers.
• If the oil level is below the lower hole or the MIN mark, add enough oil to raise the level within the lower and upper holes or within the MIN-MAX range. • Oil levels above the upper hole or the MAX mark may cause engine damage. Some oil must be removed from the engine by an authorized dealer .
Engine oil and filter recommendations Look for this certification trademark. Use SAE 5W -20 engine oil Only use oils “Certified For Gasoline Engines” by the American Petroleum Institute (API).
BATTERY Y our vehicle is equipped with a Motorcraft maintenance-free battery which normally does not require additional water during its life of service. If your battery has a cover/shield, make sure it is reinstalled after the battery has been cleaned or replaced.
When lifting a plastic-cased battery , excessive pressure on the end walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery . Lift the battery with a battery carrier or with your hands on opposite corners.
If the battery has been disconnected or a new battery has been installed, the clock and radio settings must be reset once the battery is reconnected. • Always dispose of automotive batteries in a responsible manner . Follow your local authorized standards for disposal.
When the engine is cold, check the level of the engine coolant in the reservoir . • The engine coolant should be at the “FULL COLD” level or within the “COLD FILL RANGE” as listed on the engine coolant reservoir (depending upon application).
Do not add engine coolant when the engine is hot. Steam and scalding liquids released from a hot cooling system can burn you badly . Also, you can be burned if you spill coolant on hot engine parts. Do not put engine coolant in the windshield washer fluid container .
coolant degas system with a pressurized cap, or if it is necessary to remove the coolant pressure relief cap on the radiator of a vehicle with an overflow system, follow these steps to add engine coolant. T o reduce the risk of personal injury , make sure the engine is cool before unscrewing the coolant pressure relief cap.
Recycled engine coolant Ford Motor Company does NOT recommend the use of recycled engine coolant in vehicles originally equipped with Motorcraft Premium Gold Engine Coolant since a Ford-approved recycling process is not yet available. Used engine coolant should be disposed of in an appropriate manner .
• Refer to the chart on the coolant container to ensure the coolant concentration in your vehicle will provide adequate protection at the temperatures in which you drive. V ehicles driven year -round in non-extreme climates should use a 50/50 mixture of engine coolant and distilled water for optimum cooling system and engine protection.
When fail-safe mode is activated Y ou have limited engine power when in the fail-safe mode, so drive the vehicle with caution. The vehicle will not be able to maintain high-speed operation and the engine will run rough. Remember that the engine is capable of completely shutting down automatically to prevent engine damage, therefore: 1.
If you do not use the proper fuel filler cap, excessive vacuum in the fuel tank may damage the fuel system or cause the fuel cap to disengage in a collision, which may result in possible personal injury . Automotive fuels can cause serious injury or death if misused or mishandled.
• Be particularly careful if you are taking “Antabuse” or other forms of disulfiram for the treatment of alcoholism. Breathing gasoline vapors, or skin contact could cause an adverse reaction. In sensitive individuals, serious personal injury or sickness may result.
Fuel Filler Cap Y our fuel tank filler cap has an indexed design with a 1/4 turn on/off feature. When fueling your vehicle: 1. T urn the engine off. 2. Carefully turn the filler cap counterclockwise 1/4 of a turn until it stops. 3. Pull to remove the cap from the fuel filler pipe.
If you do not use the proper fuel filler cap, excessive vacuum in the fuel tank may damage the fuel system or cause the fuel cap to disengage in a collision, which may result in personal injury . Choosing the right fuel Use only UNLEADED fuel or UNLEADED fuel blended with a maximum of 10% ethanol.
Fuel quality If you are experiencing starting, rough idle or hesitation driveability problems, try a different brand of unleaded gasoline. “Premium” unleaded gasoline is not recommended for vehicles designed to use “Regular” unleaded gasoline because it may cause these problems to become more pronounced.
ESSENTIALS OF GOOD FUEL ECONOMY Measuring techniques Y our best source of information about actual fuel economy is you, the driver . Y ou must gather information as accurately and consistently as possible. Fuel expense, frequency of fill-ups or fuel gauge readings are NOT accurate as a measure of fuel economy .
Calculating fuel economy 1. Fill the fuel tank completely and record the initial odometer reading (in miles or kilometers). 2. Each time you fill the tank, record the amount of fuel added (in gallons or liters). 3. After at least three to five tank fill-ups, fill the fuel tank and record the current odometer reading.
• Y ou may want to turn off the speed control in hilly terrain if unnecessary shifting between the top gears occurs. Unnecessary shifting of this type could result in reduced fuel economy . • W arming up a vehicle on cold mornings is not required and may reduce fuel economy .
The EP A window sticker should be your guide for the fuel economy comparisons with other vehicles. It is important to note the box in the lower left corner of the window sticker . These numbers represent the Range of MPG (L/100 km) expected on the vehicle under optimum conditions.
Exhaust leaks may result in entry of harmful and potentially lethal fumes into the passenger compartment. Do not make any unauthorized changes to your vehicle or engine.
If the Service engine soon indicator remains on, have your vehicle serviced at the first available opportunity . Although some malfunctions detected by the OBD-II may not have symptoms that are appare.
POWER STEERING FLUID Check the power steering fluid. Refer to the scheduled maintenance guide for the service interval schedules. Check the fluid level when it is at ambient temperature, 20° – 80° F (-7° – 25° C): 1. Check the fluid level on the dipstick.
BRAKE FLUID • E-150–E-350 Single Rear Wheel • E-350–E-450 Dual Rear Wheel The fluid level will drop slowly as the brakes wear , and will rise when the brake components are replaced. Fluid levels between the “MIN” and “MAX” lines are within the normal operating range; there is no need to add fluid.
T RANSMISSION FLUID Checking automatic transmission fluid (if equipped) Refer to your scheduled maintenance information for scheduled intervals for fluid checks and changes. Y our transmission does not consume fluid. However , the fluid level should be checked if the transmission is not working properly , i.
Low fluid level Do not drive the vehicle if the fluid level is at the bottom of the dipstick and the ambient temperature is above 50°F (10°C). Correct fluid level The transmission fluid should be checked at normal operating temperature 150°F-170°F (66°C-77°C) on a level surface.
The transmission fluid should be in this range if at ambient temperature (50°F-95°F [10°C-35°C]). High fluid level Fluid levels above the safe range may result in transmission failure. An overfill condition of transmission fluid may cause shift and/or engagement concerns and/or possible damage.
If an overfill occurs, excess fluid should be removed by an authorized dealer . An overfill condition of transmission fluid may cause shift and/or engagement concerns and/or possible damage. Do not use supplemental transmission fluid additives, treatments or cleaning agents.
When changing the air filter element, use only the Motorcraft air filter element listed. Refer to Motorcraft part numbers in this chapter . T o reduce the risk of vehicle damage and/or personal burn injuries do not start your engine with the air cleaner removed and do not remove it while the engine is running.
MOTORCRAFT PART NUMBERS Component 1 4.6L V8 engine 5.4L V8 engine 6.8L V10 engine Air filter element F A-1632 F A-1632 F A-1632 Battery- standard / (auxiliary) BXT -65-650 / (BXT -65-750) BXT -65-650 .
MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIES Item Capacity Ford part name Ford part number / Ford specification Brake fluid Between MIN and MAX on reservoir Motorcraft High Performance DOT 3 Moto.
Item Capacity Ford part name Ford part number / Ford specification Cooling system stop leak pellets — Motorcraft Cooling System Stop Leak Pellets VC-6 / WSS-M99B37-B6 Engine oil 6.
Item Capacity Ford part name Ford part number / Ford specification Dana Limited Slip Axle fluid M60 (M248) E250/E350 5.9 pints (2.8L) 5,7 SAE 90 Hypoid Gear Oil XY–90–GL / ESW -M2C105-E Dana Limited Slip Axle fluid M70FF (M267FF) E-350 6.6 pints (3.
Item Capacity Ford part name Ford part number / Ford specification Fuel tank–all regular and extended length vans and wagons 35.0 gallons (132.4L) —— Fuel tank–138 inch wheelbase (except E-Super Duty) 37.0 gallons (140.0L) Fuel tank–158 inch wheelbase (except E-Super Duty) 37.
ENGINE DATA Engine * 4.6L V8 engine 5.4L V8 engine 6.8L V10 engine Cubic inches 281 330 415 Required fuel 87 octane 87 octane 87 octane Firing order 1-3-7-2-6-5-4-8 1-3-7-2-6-5-4-8 1-6-5-10-2-7-3-8-4-9 Ignition system Coil on plug Coil on plug Coil on plug Spark plug gap 0.
• 4.6L V8 and 5.4L V8 Engines with A/C • 6.8L V10 Engine V EHICLE IDENTIFICATION NUMBER Complete Ford built vehicles The vehicle identification number is attached to your vehicle in the following places: • The top of the instrument panel on the driver’ s side.
• On the certification label. This label is required by the National Highway T raffic Safety Administration and is made of special material. If it is tampered with, it will be destroyed or a destruction pattern will appear . The V ehicle Identification Number (VIN) contains the following information: 1.
T RANSMISSION/T RANSAXLE CODE DESIGNATIONS Y ou can find a transmission/transaxle code on the Safety Compliance Certification Label. The following table tells you which transmission or transaxle each code represents.
GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for your vehicle through your local Ford or Ford of Canada dealer .
Peace of mind Mobile-Ease™ hands-free communication system Remote start V ehicle security systems For maximum vehicle performance, keep the following information in mind when adding accessories or e.
A Accessory delay .......................... 52 AdvanceT rac .............................. 168 Air cleaner filter ............... 261–263 Airbag supplemental restraint system .......................................... 86 and child safety seats ....
safety belts .............................. 226 washing .................................... 222 waxing ..................................... 223 wheels ...................................... 223 wiper blades ............................ 225 Climate control (see Air conditioning or Heating) .
Exhaust fumes .......................... 163 F Fail safe cooling ........................ 243 Fluid capacities ......................... 264 Four -Wheel Drive vehicles preparing to drive your vehicle ..................................... 172 Fuel ....
positions of the ignition ......... 161 L Lamps bulb replacement specifications chart .................. 40 daytime running light ...............35 headlamps ................................. 34 headlamps, flash to pass .......... 35 instrument panel, dimming .
Belt-Minder 威 ............................. 81 extension assembly .................. 85 for adults ............................. 77–79 for children ......................... 95–96 safety belt maintenance ........... 85 warning light and chime ..
W asher fluid .............................. 232 W ater , Driving through ............. 185 W indows power ......................................... 51 W indshield washer fluid and wipers .......................................... 46 checking and adding fluid .
280.
Een belangrijk punt na aankoop van elk apparaat Ford 2008 E-150 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Ford 2008 E-150 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Ford 2008 E-150 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Ford 2008 E-150 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Ford 2008 E-150 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Ford 2008 E-150 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Ford 2008 E-150 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Ford 2008 E-150 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
