Gebruiksaanwijzing /service van het product 2010 Escape Hybrid van de fabrikant Ford
Ga naar pagina of 352
Introduction 4 Instrument Cluster 18 W arning lights and chimes 18 Gauges 23 Message center 25 Entertainment Systems 34 AM/FM stereo with CD/MP3 34 Auxiliary input jack (Line in) 43 USB port 45 Satell.
Seating and Safety Restraints 1 15 Seating 115 Safety restraints 127 Airbags 140 Child restraints 155 Tires, Wheels and Loading 173 T ire information 175 T ire inflation 177 T ire Pressure Monitoring .
Maintenance and Specifications 288 Engine compartment 290 Engine oil 293 Battery 296 Engine Coolant and Motor/Electronics Coolant 298 Fuel information 304 Air filter(s) 317 Part numbers 318 Maintenanc.
CONGRATULATIONS Congratulations on acquiring your new Ford Hybrid. Please take the time to get well acquainted with your vehicle by reading this handbook. The more you know and understand about your vehicle, the greater the safety and pleasure you will derive from driving it.
W arning symbols on your vehicle When you see this symbol, it is imperative that you consult the relevant section of this guide before touching or attempting adjustment of any kind. Protecting the environment W e must all play our part in protecting the environment.
Do not add friction modifier compounds or special break-in oils since these additives may prevent piston ring seating. See Engine oil in the Maintenance and Specifications chapter for more information on oil usage.
Stopping: The gas engine may shut off to conserve fuel as you come to a stop. Restarting the vehicle is not required. Simply step on the accelerator when you are ready to drive.
Engine: The engine speed in your hybrid is not directly tied to your vehicle speed. Y our vehicle’ s engine and transmission are designed to deliver the power you need at the most efficient engine speed. During heavy accelerations, your hybrid may reach high engine speeds (up to 6000 RPM).
Additional T ips: • Do not carry extra loads • Be mindful of adding external accessories that may increase aerodynamic drag • Observe posted speed limits • Perform all scheduled maintenance • There is no need to wait for your engine to “warm up”.
Question Answer After I start my car in the morning, why does it take a long time before the engine shuts down? There are several reasons the engine stays on for an extended amount of time when it is first started. One common reason is to ensure that the emissions components are warm enough to minimize tailpipe emissions.
Question Answer What does it mean when my power assist gauge moves to the right? T o the left? Electricity is coming out of the battery when the gauge moves to the right.
Question Answer How long will my high voltage battery last? Does it need maintenance? The high voltage battery system is designed to last the life of the vehicle and requires no maintenance.
Notice to owners of pickup trucks and utility type vehicles W ARNING: Utility vehicles have a significantly higher rollover rate than other types of vehicles. Before you drive your vehicle, please read this Owner’ s Guide carefully . Y our vehicle is not a passenger car .
Event Data Recording Other modules in your vehicle — event data recorders — are capable of collecting and storing data during a crash or near crash event.
information”) only to help provide you with the directions, traffic reports, or business searches you request. If you do not want Ford or its vendors to receive this information, do not activate the service. Ford Motor Company and the vendors it uses to provide you with this information do not store your vehicle travel information.
These are some of the symbols you may see on your vehicle. V ehicle Symbol Glossary Safety Alert See Owner’ s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat Lower Anchor Child Seat.
V ehicle Symbol Glossary Power W indows Front/Rear Power W indow Lockout Child Safety Door Lock/Unlock Interior Luggage Compartment Release Panic Alarm Engine Oil Engine Coolant Engine Coolant T emper.
W ARNING LIGHTS AND CHIMES W arning lights and gauges can alert you to a vehicle condition that may become serious enough to cause extensive repairs. A warning light may illuminate when a problem exists with one of your vehicle’ s functions. Many lights will illuminate when you start your vehicle to make sure the bulbs work.
W ARNING: Under engine misfire conditions, excessive exhaust temperatures could damage the catalytic converter , the fuel system, interior floor coverings or other vehicle components, possibly causing a fire.
Safety belt: Reminds you to fasten your safety belt. A Belt-Minder 威 chime will also sound to remind you to fasten your safety belt. Refer to the Seating and Safety Restraints chapter to activate/deactivate the Belt-Minder 威 chime feature.
High engine or high motor electronic coolant temperature: Illuminates when the engine coolant or motor electronics coolant temperature is high. The message center displays HIGH ENGINE TEMPERA TURE / HIGH MOTOR TEMPERA TURE when the engine coolant or motor electronics are overheating.
Low fuel: Illuminates when the fuel level in the fuel tank is at or near empty (refer to Fuel gauge in this chapter). Speed control: Illuminates when the speed control is engaged. T urns off when the speed control system is disengaged. Anti-theft system: Flashes when the SecuriLock 威 passive anti-theft system has been activated.
HEV engine off reminder chime: Sounds for 10 seconds when the PRNDL is in the P (Park) position and the Driver’ s door is ajar (open) while ignition is on.
Battery gauge: Provides information about the vehicle’ s energy usage. • ASSIST — Battery provides extra power to boost the vehicle’ s acceleration. • CHARGE — Storing extra energy in the battery when coasting or slowing down. Odometer: Registers the total miles (kilometers) of the vehicle.
MESSAGE CENTER Y our vehicle’ s message center is capable of monitoring many vehicle systems and will alert you to potential vehicle problems and various conditions with an informational message followed by a long indicator chime. The message center display is located in the instrument cluster .
A VG MPG (L/100km) A verage fuel economy displays your average fuel economy in miles/gallon or liters/100 km. If you calculate your average fuel economy by dividing distance traveled by gallons of fue.
System check and vehicle feature customization Press the SETUP button repeatedly to cycle the message center through the following features: PRESS RESET FOR ENGLISH (if in another language) When entering the setup menu and a non-English language has been selected, this message will be displayed to change back to English.
2. Press and hold the RESET button for two seconds and release to reset the oil life to 100%. Note: T o change oil life 100% miles value from 7,500 miles (12,000 km) or 12 months to another value, proceed to Step 3. 3. Once “OIL LIFE SET TO XXX%” is displayed, release and press the RESET button to change the Oil Life Start V alue.
RESET FOR CALIBRA TION For more information on the compass and compass set up, refer to Electronic compass in the Driver Controls chapter . LANGUAGE = ENGLISH / SP ANISH / FRENCH Allows you to choose which language the message center will display in. Selectable languages are English, Spanish, or French.
STOP SAFEL Y NOW — Displayed when the stop safety hazard warning lamp is illuminated. This indicates a hybrid component fault/failure that will cause the vehicle to shut down, fail to start or enter into limited operating mode. Note: If the vehicle is still running, it may soon shut down without further warning and should be stopped safely .
CHECK FUEL FILL INLET — Displayed when the fuel fill inlet may not be properly closed. Refer to Easy Fuel™ “no cap” fuel system in the Maintenance and Specifications chapter . BRAKE FLUID LEVEL LOW — Indicates the brake fluid level is low and the brake system should be inspected immediately .
VEHICLE NEAR TOP SPEED — Displayed when a MyKey™ is in use and the MyKey speed limit is on and the vehicle speed is approaching 80 mph (130 km/h). Refer to MyKey™ in the Locks and Security chapter for more information.
SP ACE FOUND PULL FOR W ARD (if equipped) — May display when using the active park assist system. See Active park assist in the Driving chapter for more information. SP ACE FOUND STOP (if equipped) — May display when using the active park assist system.
AUDIO SYSTEMS Note: If your volume is muted and MYKEY VOLUME LIMITED is displayed, refer to MyKey™ in the Locks and Security chapter for more information. AM/FM/single CD/MP3 satellite compatible sound system W ARNING: Driving while distracted can result in loss of vehicle control, accident and injury .
Setting the clock T o set the time, press CLOCK. The display will read SET TIME. Use the memory preset numbers (0–9) to enter in the desired time–hours and minutes. The clock will then begin from that time. AM/FM Radio / VOL (Power/V olume): Press to turn the radio on/off.
MEMOR Y PRESETS (0–9): When tuned to any station, press and hold a preset button until sound returns and PRESET # SA VED appears in the display . Y ou can save up to 30 stations, 10 in AM, 10 in FM1 and FM2.
CD/MP3 Player CD: Press to enter CD/MP3 mode. If a disc is already loaded into the system, CD/MP3 play will begin where it ended last. If no CD is loaded, NO DISC will appear in the display . LOAD: This control is not operational. T o load a CD, simply insert the disc, label side up, into the CD slot.
TEXT : In MP3 mode only– Press TEXT repeatedly to view Album (AL), Folder (FL), Song (SO) and Artist (AR) in the display , if available. In TEXT MODE– Sometimes the display requires additional text to be displayed. When th e</>i n d i c a t o ri sa c t i v e ,p r e s s TEXT and then press SEEK/TRACK to view the additional display text.
SEEK/TRACK: Press SEEK/TRACK to seek to the previous/next channel. If a specific category is selected, (Jazz, Rock, News, etc.), press SEEK/TRACK to seek to the previous/next channel in the selected category . Press and hold SEEK/TRACK to fast seek through the previous/next channels.
SA TELLITE RADIO MENU: Press MENU when satellite radio mode is active to access. Press OK to enter into the satellite radio menu. Press / to cycle through the following options: • CA TEGOR Y MENU- Press OK to enter category mode. Press / to scroll through the list of available SIRIUS 威 channel Categories (Pop, Rock, News, etc.
d. DISABLE ALER TS/ENABLE ALER TS: Press OK to enable/disable the satellite alert status which alerts you when your selected songs are playing on a satellite radio channel. (The system default is disabled.) SONG ALERTS ENABLED/DISABLED will appear in the display .
Sound Adjustments Press SOUND repeatedly to cycle through the following features: BASS: Press SEEK/TRACK to adjust the level of bass. TREBLE: Press SEEK/TRACK to adjust the level of treble. BALANCE: Press SEEK/TRACK to adjust the audio between the left (L) and right (R) speakers.
Extra Features AUX: Press repeatedly to cycle through LINE IN (auxiliary audio mode), and SYNC 威 (if equipped). For location and further information on auxiliary audio mode, refer to Auxiliary input jack later in this chapter .
Y our vehicle is equipped with an Auxiliary Input Jack (AIJ). The Auxiliary Input Jack provides a way to connect your portable music player to the in-vehicle audio system. This allows the audio from a portable music player to be played through the vehicle speakers with high fidelity .
7. Adjust the sound on your portable music player until it reaches the level of the FM station or CD by switching back and forth between the AUX and FM or CD controls. T roubleshooting: 1. Do not connect the audio input jack to a line level output. Line level outputs are intended for connection to a home stereo and are not compatible with the AIJ.
Y our vehicle may be equipped with a USB port located on the instrument panel. This feature allows you to plug in media playing devices, memory sticks, and also to charge devices if they support this feature.
CD/CD player care Do: • Handle discs by their edges only . (Never touch the playing surface). • Inspect discs before playing. • Clean only with an approved CD cleaner . • W ipe discs from the center out. Don’t: • Expose discs to direct sunlight or heat sources for extended periods of time.
CDs with homemade paper (adhesive) labels should not be inserted into the CD player as the label may peel and cause the CD to become jammed. It is recommended that homemade CDs be identified with permanent felt tip marker rather than adhesive labels. Ballpoint pens may damage CDs.
Sample MP3 structure If you are burning your own MP3 discs, it is important to understand how the system will read the structures you create. While various files may be present, (files with extensions other than mp3), only files with the .mp3 extension will be played.
• T errain: Hills, mountains, tall buildings, bridges, tunnels, freeway overpasses, parking garages, dense tree foliage and thunderstorms can interfere with your reception. • Station overload: When you pass a ground based broadcast repeating tower , a stronger signal may overtake a weaker one and result in an audio mute.
Radio Display Condition Action Required ACQUIRING Radio requires more than two seconds to produce audio for the selected channel. No action required. This message should disappear shortly .
Radio Display Condition Action Required NO TEXT Category information not available. Category information not available at this time on this channel. The system is working properly . NO SIGNAL Loss of signal from the SIRIUS 威 satellite or SIRIUS 威 tower to the vehicle antenna.
DUAL AUTOMATIC TEMPERATURE CONTROL 1. AUTO/Driver temperature: Press to engage full automatic operation. The system will automatically determine fan speed, airflow distribution, A/C on or off, and outside or recirculated air , to heat or cool the vehicle to reach the desired temperature.
5. Power/ : Press to activate/deactivate the climate control system. When the system is off, outside air is shut out. Press + or – to manually increase/decrease the fan speed. The manual fan speed setting will appear on the left side of the display .
14. Driver heated seat control (if equipped): Press to activate/deactivate the driver heated seat. See Heated seats in the Seating and Safety Restraints chapter . Outside temperature: The outside temperature will appear in the display and is labeled EXT TEMP .
5. Set highest fan setting initially , then adjust to maintain comfort. T o aid in side window defogging/demisting in cold weather: 1. Select . 2. Select A/C. 3. Adjust the temperature control to maintain comfort. 4. Set the fan speed to the highest setting.
HEADLAMP CONTROL Rotate the headlamp control to the first position to turn on the parking lamps. Rotate to the second position to turn on the headlamps.
2. Rotate the headlamp control to the autolamp position. 3. Rotate the headlamp control to the off position. 4. T urn the key to the on position. 5. T urn the key back to the off position. 6. T urn the headlamp control to the autolamp position (the headlights should turn on).
Flash to pass Pull toward you slightly to activate and release to deactivate. Daytime running lamps (DRL) (if equipped) T urns the lowbeam headlamps on with a reduced output. T o activate: • the ignition must be in the on position. • the headlamp control must be in the off , parking lamps or autolamp position.
Note: If the battery is disconnected, discharged, or a new battery is installed, the dimmer switch requires re-calibration. Rotate the dimmer switch from the full dim position to the full dome/on position to reset. This will ensure that your displays are visible under all lighting conditions.
5. Locate the vertical adjuster on the headlamp, then turn the adjuster either clockwise (to adjust up) or counterclockwise (to adjust down) aligning the upper edge of the light pattern to the horizontal line. 6. Move the opaque cloth to cover the right-hand headlamp and repeat Steps 4 and 5 for the left-hand headlamp.
The map lamp controls (without moon roof) are located on the dome lamp. Press the button on either side of each map lamp to illuminate the lamps. Press the button again to turn off the lamps. For models equipped with a moon roof, the map lamps are located on the moon roof control panel.
Ambient lighting (if equipped) Illuminates footwells, cupholders, the console bin and the console tray with a choice of several colors. The ambient lighting control switch is located on the floor console. T o activate, press and release the control to cycle through the color choices plus the off state.
T ake your vehicle to dealer for service if any of the above conditions of unacceptable moisture are present. Using the right bulbs Replacement bulbs are specified in the chart below .
Replacing headlamp bulbs 1. Make sure that the headlamp control is in the off position. 2. Open the hood. 3. Reach over the front bolster . 4. Remove the bulb by turning it counterclockwise and then pulling it straight out. 5. Disconnect the electrical connector from the bulb.
5. Carefully pull the bulb out of the socket and push in the new bulb. 6. Install the bulb socket into the lamp assembly and rotate clockwise. Replacing front sidemarker bulbs For bulb replacement, see your authorized dealer .
Replacing license plate lamp bulbs 1. Make sure the headlamp switch is in the off position. 2. Depress the lever and carefully pry the license plate lamp assembly (located above the license plate) from the liftgate. 3. Rotate the bulb socket counterclockwise and remove from lamp assembly .
3. Pull the bulb straight out of the socket and push in the new bulb. T o complete installation, follow the removal procedure in reverse order . Replacing fog lamp bulbs (if equipped) 1. Make sure the fog lamp switch is in the off position. 2. From underneath the vehicle, carefully disconnect the electrical connector from the bulb.
MULTI-FUNCTION LEVER W indshield wiper: Rotate the end of the control away from you to increase the speed of the wipers; rotate towards you to decrease the speed of the wipers. W indshield washer: Press the end of the stalk: • briefly: causes a single swipe of the wipers without washer fluid.
Rear window wiper/washer controls For rear wiper operation, rotate the rear window wiper and washer control to the desired position. Select: 2 — Normal speed operation of rear wiper . 1 — Intermittent operation of rear wiper . O (off) — Rear wiper and washer off.
ILLUMINATED VISOR MIRROR Lift the mirror cover to turn on the visor mirror lamps. Slide on rod feature The visor will slide back and forth on the rod for increased sunlight coverage. Rotate the visor towards the side window and extend it rearward for additional sunlight coverage.
Compass zone adjustment 1. Determine which magnetic zone you are in for your geographic location by referring to the zone map. 2. T urn ignition to the on position. 3. Start the engine. 4. Press the SETUP control to select the Update Zone function and display the current ZONE XX in the center stack display .
2. T o calibrate, press and hold the RESET control for approximately ten seconds until CAL appears. Release the control. 3. Slowly drive the vehicle in a circle (less than 3 mph [5 km/h]) until the CAL display changes to the direction value. It may take up to five circles to complete calibration.
The tray and inside bin can be removed to open up space to fit a laptop computer , MP3 players, CDs or handbags. T o remove, open the console lid and pull the bin straight up and out from the console housing. The sliding tray and inside bin can be hooked on the side or rear of the console for extra storage.
T o have full capacity usage of your power point, the engine is required to be running to avoid unintentional discharge of the battery . T o prevent the battery from being discharged: • do not use t.
defeat the safety protection design provided by the cap and twist tab. It will also cause the power point to overload due to powering multiple devices that can reach beyond the 150W load limit. The power point can switch to a fault mode when it is overloaded, overheated, or shorted.
One-touch down (AUTO) Allows the driver’ s window to open fully without holding the control down. Press the switch completely down to the second detent and release quickly . The window will open fully . Momentarily press the switch to any position to stop the window operation.
Do not block the sensors on the front and back of the interior rear view mirror since this may impair proper mirror performance. Do not clean the housing or glass of any mirror with harsh abrasives, fuel or other petroleum-based cleaning products.
Heated outside mirrors (if equipped) Both mirrors are heated automatically to remove ice, mist and fog when the rear window defrost is activated. Do not remove ice from the mirrors with a scraper or attempt to readjust the mirror glass if it is frozen in place.
3. Press the SET + control and release it. 4. T ake your foot off the accelerator pedal. 5. The indicator light on the instrument cluster will turn on.
Increasing speed while using speed control There are three ways to set a higher speed: • Press and hold the SET + control until you get to the desired speed, then release the control. • Press and release the SET + control to operate the T ap-Up function.
STEERING WHEEL CONTROLS These controls allow you to operate some audio control features. Radio control features Press MEDIA to select: • AM, FM1, FM2, or CD • SA T1, SA T2 or SA T3 (Satellite radio mode) • LINE IN (Auxiliary input jack) In Radio mode: • Press to access the next/previous preset station.
Navigation system hands free control features (if equipped) Press and hold control briefly until the voice icon appears on the navigation display to use the voice command feature. Press to complete a voice command. For further information on the navigation system, refer to the Navigation System supplement.
For further information on the Navigation system/SYNC 威 system, refer to the Navigation System and SYNC 威 supplements. MOON ROOF (IF EQUIPPED) Y ou can move the glass panel of the moon roof back to open or tilt up (from the closed position) to ventilate the vehicle.
roof reaches the bounce-back position, the moon roof will travel with no bounce-back protection. If the control is released before the moon roof reaches fully closed or the ignition is turned off (without accessory delay being active), the moon roof will stop.
Do not use the Car2U 威 system with any garage door opener that lacks safety stop and reverse features as required by U.S. Federal Safety Standards (this includes any garage door opener manufactured before April 1, 1982).
Rolling code programming Note: Programming the rolling code garage door opener involves time-sensitive actions. Read the entire procedure prior to beginning so you will know which actions are time-sensitive. If you do not follow the time-sensitive actions, the device will time out and you will have to repeat the procedure.
3. Return to your vehicle. Press and hold the Car2U 威 system button you would like to use to control the garage door . Y ou may need to hold the button from 5–20 seconds, during which time the selected button indicator light will blink slowly . Immediately (within 1 second) release the button once the garage door moves.
1. T o program units with fixed code DIP switches, you will need the garage door hand-held transmitter , paper and a pen or pencil. 2. Open the battery cover and record the switch settings from left to right for all 8 to 12 switches. Use the figure below: When a switch is in the up, on, or + position, circle “L.
5. Press and hold the Car2U 威 system button you would like to use to control the garage door . Immediately (within 1 second) release the button once the garage door moves. During this time the selected button indicator light will blink slowly . Do not release the button until you see the garage door move.
FCC and RSS-210 Industry Canada Compliance The Car2U 威 system complies with Part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) Th.
CARGO AREA FEATURES Cargo shade (if equipped) If your vehicle has a cargo shade, you can use it to cover items in the cargo area of your vehicle. T o install the shade: • Insert the ends of the cargo shade into the mounting features located behind the rear seat on the rear trim panels.
W ARNING: When loading the roof rail crossbars, it is recommended to evenly distribute the load, as well as maintain a low center of gravity . Loaded vehicles, with higher centers of gravity , may handle differently than unloaded vehicles.
3. Use a long, flat object to depress the tongue in the endcaps on both sides of the cross-bar . 4. Slide the cross-bar assembly off the end of the rail. Be sure to check that the thumbwheels are tight each time load is added, or removed from the roof rack, and periodically while traveling.
KEYS Y our vehicle is equipped with two Integrated Keyhead T ransmitters (IKT s). The key blade functions as a programmed key which starts the vehicle and unlocks/locks all the doors. The transmitter portion functions as the remote entry transmitter .
POWER DOOR LOCKS • Press the control to unlock all doors. • Press the control to lock all doors. Door key unlocking/locking Unlocking the doors T urn the key in the door cylinder to unlock the driver’ s door only . All other doors will remain locked.
Note: The autolock feature can be activated/deactivated independently of the autounlock feature. Before following the activation or deactivation procedures, make sure that the anti-theft system is not armed, ignition is in the off position, and all vehicle doors, liftgate and liftgate window are closed.
Message center procedure For information on activating/deactivating the autolock feature using the vehicle’ s message center , refer to Message center information in the Instrument Cluster chapter .
1. Place the key in the ignition and turn the ignition to the on position. 2. Press the power door unlock control on the door panel three times. 3. T urn the ignition from the on position to the off position. 4. Press the power door unlock control on the door panel three times.
CHILDPROOF DOOR LOCKS When these locks are set, the rear doors cannot be opened from the inside. The rear doors can be opened from the outside when the doors are unlocked. The childproof locks are located on rear edge of each rear door and must be set separately for each door .
The IKT allows you to: • remotely unlock the vehicle doors. • remotely lock all the vehicle doors. • remotely open the power liftgate glass. • activate the personal alarm. • operate the illuminated entry feature. The remote entry lock/unlock feature operates in any ignition position except while the key is held in the start position.
Switching from two step to one step door unlocking Unlocking can be switched between two step and one step door unlocking by pressing and holding both and buttons simultaneously on the remote entry transmitter for approximately 4 seconds. The turn signal will flash twice to indicate that the vehicle has switched to one step unlocking.
Replacing the battery The Integrated Keyhead T ransmitter uses one coin type three-volt lithium battery CR2032 or equivalent. T o replace the battery: 1. T wist a thin coin in the slot of the IKT near the key ring in order to remove the battery cover .
The illuminated entry system will turn off the lights if: • the ignition is turned to the on position, or • the Integrated Keyhead T ransmitter lock control is pressed, or • the vehicle is locked using the keyless entry keypad (if equipped), or • after 25 seconds of illumination.
2. W ithin five seconds press the 1 • 2 on the keypad. 3. Enter your personal 5–digit code. Each number must be entered within five seconds of each other . 4. Three unique personal entry codes can be stored: • Pressing 1 • 2 assigns Driver 1 settings.
T o unlock all doors and liftgate, press the 3 • 4 control within five seconds of entering the factory set 5-digit code or your personal code. T o lock all doors and liftgate, press the 7 • 8 and the 9 • 0a tt h e same time. Note: The driver’ s door must be closed.
Anti-theft indicator The anti-theft indicator is located in the instrument panel cluster . • When the ignition is in the off position, the indicator will flash once every two seconds to indicate the SecuriLock 威 system is functioning as a theft deterrent.
keyless entry transmitter . A maximum of eight coded keys can be programmed to your vehicle; only four of these eight keys can be IKT s with remote entry functionality . If your IKT s or standard SecuriLock 威 coded keys are lost or stolen and you don’t have an extra coded key , you will need to have your vehicle towed to an authorized dealer .
4. After three seconds but within 10 seconds of turning the ignition to the 1 (off) position, insert the second previously coded key into the ignition. 5. T urn the ignition from the 1 (off) position to the 3 (on) position. Keep the ignition in the 3 (on) position for at least three seconds, but no more than 10 seconds.
MyKey™ Restricted Features Standard settings – These settings cannot be changed • The audio system will be muted whenever Belt-Minder 威 is activated until the safety belts are buckled. Refer to the Seating and Safety Restraints chapter for a detailed description of Belt-Minder 威 operation.
Note: The MyKey™ can be cleared within the same key cycle that it was created, otherwise a standard key (Administrator key) is required to disable the MyKey™ programming. T o clear all MyKeys™ go to step 2 in the Disable MyKey™ section. Programming MyKey™ Optional Settings T urn the ignition on using an Admin key .
Check MyKey™ System Status The vehicle System Check will provide the status of the following MyKey™ parameters: • MYKEY MILES — This odometer only tracks mileage when a MyKey™ is used. If mileage does not accumulate as expected, then the MyKey™ is not being used by the intended user .
Note: For all vehicles with remote start installed, it is possible to program all ’real’ keys as MyKeys™, in which case, you will need to use your remote start system to reset all MyKeys™ as Admin keys by doing the following: 1. Enter the vehicle, close all doors.
Condition Potential Causes Lost any key • For programming spare keys, refer to the Programming spare keys section in this chapter . I accidentally programmed all keys as MyKeys™ • V ehicle has a remote start system that is recognized as an Admin key .
FRONT SEATS W ARNING: Reclining the seatback can cause an occupant to slide under the seat’ s safety belt, resulting in severe personal injuries in the event of a collision. W ARNING: Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop.
T o adjust the head restraint, do the following: 1. Adjust the seatback to an upright driving/riding position. 2. Raise the head restraint by pulling up on the head restraint. 3. Lower the head restraint by pressing and holding the guide sleeve adjust/release button and pushing down on the head restraint.
T o remove the adjustable head restraint, do the following: 1. Pull up the head restraint until it reaches the highest adjustment position. 2. Simultaneously press and hold both the adjust/release button and the unlock/remove button, then pull up on the head restraint.
W ARNING: T o minimize the risk of neck injury in the event of a crash, head restraints must be installed properly . Adjusting the front manual seat (if equipped) Lift handle to move seat forward or backward.
W ARNING: Reclining the seatback can cause an occupant to slide under the seat’ s safety belt, resulting in severe personal injuries in the event of a collision.
Press the control to move the seat forward, backward, up or down. Heated seats (if equipped) W ARNING: Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury , medication, alcohol use, exhaustion, or other physical conditions, must exercise care when using the seat heater .
W ARNING: T o minimize the risk of neck injury in the event of a crash, the driver and passenger occupants should not sit in and/or operate the vehicle, until the head restraint is placed in its proper position. The driver should never adjust the head restraint while the vehicle is in motion.
Properly adjust the head restraint so that the top of the head restraint is even with the top of your head and positioned as close as possible to the back of your head. For occupants of extremely tall stature, adjust the head restraint to its full up position.
T o reinstall the adjustable head restraint, do the following: 1. Insert the two stems into the guide sleeve collars. 2. Push the head restraint down until it locks. Properly adjust the head restraint so that the top of the head restraint is even with the top of your head and positioned as close as possible to the back of your head.
3. Flip seat forward. Attach the safety belt web snap button to the quarter trim panel snap button. This will ensure that safety belt does not get caught by staying out of the seat back folding path. 4. T o release seatback, pull the seatback release lever (on top of seat) toward the front seat.
5. Rotate seatback down into load floor position. Returning the second row seats to upright position 1. Pull seatback up and into upright position making sure seatback locks into place and the red seat unlatched indicator on release paddle is not visible.
W ARNING: Make sure safety belt buckle heads are through elastic holders on seat backs. Safety belt buckles may break if they are trapped underneath the seatback as the seatback is rotated down. W ARNING: Before returning the seatback to its original position, make sure that cargo or any objects are not trapped behind the seatback.
T o install the second row cushion 1. Push the cushion to the inboard side of the vehicle. 2. Make sure that the hinges are locked into place. SAFETY RESTRAINTS Personal Safety System™ The Personal .
conditions. A collection of crash and occupant sensors provides information to the Restraints control module (RCM). During a crash, the RCM may activate the safety belt pretensioners and/or either one or both stages of the dual-stage airbag supplemental restraints based on crash severity and occupant conditions.
occupant is not properly restrained by safety belts or child safety seats and they move forward during pre-crash braking. The most effective way to reduce the risk of unnecessary injuries is to make sure all occupants are properly restrained.
increase the effectiveness of the safety belts. In frontal collisions, the safety belt pretensioners can be activated alone or , if the collision is of sufficient severity , together with the front airbags.
W ARNING: T o reduce the risk of injury , make sure children sit where they can be properly restrained. W ARNING: Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision.
Combination lap and shoulder belts 1. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) until you hear a snap and feel it latch. Make sure the tongue is securely fastened in the buckle. 2. T o unfasten, press the release button and remove the tongue from the buckle.
(8 km/h) or more, the combination safety belts will lock to help reduce forward movement of the driver and passengers. Automatic locking mode When to use the automatic locking mode In this mode, the shoulder belt is automatically pre-locked. The belt will still retract to remove any slack in the shoulder belt.
How to disengage the automatic locking mode Disconnect the combination lap/shoulder belt and allow it to retract completely to disengage the automatic locking mode and activate the vehicle sensitive (emergency) locking mode.
Safety belt pretensioner Y our vehicle is equipped with safety belt pretensioners at the driver and front passenger seating positions. The safety belt pretensioners activate during frontal collisions, and in side collisions and rollovers.
Conditions of operation If... Then... The driver’ s safety belt is not buckled before the ignition switch is turned to the on position... The safety belt warning light illuminates 1 minute and the warning chime sounds 6 seconds. The driver’ s safety belt is buckled while the indicator light is illuminated and the warning chime is sounding.
If... Then... The driver’ s and front passenger’ s safety belts are buckled before the ignition switch is turned to the on position or less than 1-2 minutes have elapsed since the ignition switch has been turned to on... The Belt-Minder 威 feature will not activate.
The following are reasons most often given for not wearing safety belts (All statistics based on U.S. data): Reasons given... Consider ... ⬙ Crashes are rare events ⬙ 36700 crashes occur every day . The more we drive, the more we are exposed to ⬙ rare ⬙ events, even for good drivers.
Reasons given... Consider ... ⬙ I have an airbag ⬙ Airbags offer greater protection when used with safety belts. Frontal airbags are not designed to inflate in rear and side crashes or rollovers. ⬙ I’d rather be thrown clear ⬙ Not a good idea.
1. T urn the ignition switch to the on position. DO NOT ST ART THE ENGINE. 2. W ait until the safety belt warning light turns off (Approximately 1 minute). • Step 3 must be completed within 30 seconds after the safety belt warning light turns off. 3.
Important SRS precautions The SRS is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries.
W ARNING: Do not attempt to service, repair , or modify the airbag supplemental restraint systems or its fuses. Contact your authorized dealer as soon as possible.
How does the airbag supplemental restraint system work? The airbag SRS is designed to activate when the vehicle sustains a longitudinal deceleration sufficient to cause the airbag sensors to close an electrical circuit that initiates airbag inflation.
• seat-mounted side airbags. Refer to Seat-mounted side airbag system later in this chapter • Safety Canopy 威 System. Refer to Safety Canopy 威 System later in this chapter . • one or more impact and safing sensors. • Safety belt pretensioners • a readiness light and tone.
The front passenger sensing system will disable (will not inflate) the front passenger’ s frontal airbag if: • the front passenger seat is unoccupied, or has small/medium objects in the front seat.
• When the front passenger sensing system enables the front passenger frontal airbag (may inflate), the indicator will be unlit and stay unlit. If a person of adult size is sitting in the front pass.
W ARNING: Sitting improperly out of position or with the seat back reclined too far can take off weight from the seat cushion and affect the decision of the front passenger sensing system, resulting in serious injury or death in a crash. Always sit upright against your seatback, with your feet on the floor .
W ARNING: T o reduce the risk of possible serious injury: Do not stow objects in seat back map pocket (if equipped) or hang objects off seat back if a child is in the front passenger seat. Do not place objects underneath the front passenger seat or between the seat and the center console (if equipped).
W ARNING: Any alteration/modification to the front passenger seat may affect the performance of the front passenger sensing system. Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a tone to indicate the status of the system.
W ARNING: Do not attempt to service, repair , or modify the airbag SRS, its fuses or the seat cover on a seat containing an airbag. See an authorized dealer . W ARNING: All occupants of the vehicle should always wear their safety belts even when an airbag SRS is provided.
The airbag SRS is designed to activate when the vehicle sustains lateral deceleration sufficient to cause the sensors to close an electrical circuit that initiates airbag inflation. The fact that the airbags did not inflate in a collision does not mean that something is wrong with the system.
Safety Canopy 姞 System W ARNING: Do not place objects or mount equipment on or near the headliner at the siderail that may come into contact with a deploying Safety Canopy 威 . Failure to follow these instructions may increase the risk of personal injury in the event of a collision.
How does the Safety Canopy 姞 System work? The design and development of the Safety Canopy 威 System included recommended testing procedures that were developed by a group of automotive safety experts known as the Side Airbag T echnical W orking Group.
The Safety Canopy 威 is mounted to roof side-rail sheet metal, behind the headliner , above the first and second row seats. The Safety Canopy 威 is designed to inflate between the side window area and occupants to further enhance protection provided in side impact collisions and rollover events.
A difficulty with the system is indicated by one or more of the following: • The readiness light (same light as for front airbag system) will either flash or stay lit. • The readiness light will not illuminate immediately after ignition is turned on.
Important child restraint precautions W ARNING: Always make sure your child is secured properly in a device that is appropriate for their height, age and weight.
Recommendations for Safety Restraints for Children Child size, height, weight, or age Recommended restraint type Infants or tod- dlers Children weighing 40 lb (18 kg) or less (generally age four or younger) Use a child safety seat (sometimes called an infant carrier , convertible seat, or toddler seat).
Recommendations for attaching child safety restraints for children Re- straint T ype Child W eight Use any attachment method as indicated be- low by “X” LA TCH (lower an- chors and top tether an- .
W ARNING: Always carefully follow the instructions and warnings provided by the manufacturer of any child restraint to determine if the restraint device is appropriate for your child’ s size, height, weight, or age.
training to ensure that all children ages 0 to 16 are properly restrained in the correct restraint system. Ford recommends checking with a NHTSA Certified Child Passenger Safety T echnician (CPST) and your pediatrician to make sure your seat is appropriate for your child and properly installed in the vehicle.
Airbags can kill or injure a child in a child seat. NEVER place a rear -facing child seat in front of an active airbag. If you must use a forward-facing child seat in the front seat, move the vehicle seat all the way back. Children 12 and under should be properly restrained in a rear seating position whenever possible.
Perform the following steps when installing the child seat with combination lap/shoulder belts: Note: Although the child seat illustrated is a forward facing child seat, the steps are the same for installing a rear facing child seat. 1. Position the child safety seat in a seat with a combination lap and shoulder belt.
3. While holding the shoulder and lap belt portions together , route the tongue through the child seat according to the child seat manufacturer’ s instructions.
8. Remove remaining slack from the belt. Force the seat down with extra weight, e.g., by pressing down or kneeling on the child restraint while pulling up on the shoulder belt in order to force slack from the belt.
method eliminates the need to use safety belts to attach the child seat, however the safety belt can still be used to attach the child seat. For forward-facing child seats, the top tether strap must also be attached to the proper top tether anchor , if a top tether strap has been provided with your child seat.
W ARNING: Depending on where you secure a child restraint, and depending on the child restraint design, you may block access to certain safety belt buckle assemblies and/or LA TCH lower anchors, rendering those features potentially unusable.
Combining safety belt and LA TCH lower anchors for attaching child safety seats When used in combination, either the safety belt or the LA TCH lower anchors may be attached first, provided a proper installation is achieved. Attach the tether strap afterward, if included with the child seat.
2. Locate the correct anchor for the selected seating position. There are three tether anchors located on the headliner at the rear of the vehicle. 3. Clip the tether strap to the anchor as shown. The arrow in the above graphic points toward the front of the vehicle.
around four (4) years of age. Consult your child safety seat owner guide for the weight, height, and age limits specific to your child safety seat. Keep your child in the child safety seat if it properly fits the child, remains appropriate for their weight, height and age AND if properly secured to the vehicle.
• Is the shoulder belt centered on the shoulder and chest? • Can the child stay seated like this for the whole trip? T ypes of booster seats There are generally two types of belt-positioning booster seats: backless and high back. Always use booster seats in conjunction with the vehicle lap/shoulder belt.
Children and booster seats vary in size and shape. Choose a booster that keeps the lap belt low and snug across the hips, never up across the stomach, and lets you adjust the shoulder belt to cross the chest and rest snugly near the center of the shoulder .
Follow all instructions provided by the manufacturer of the booster seat. W ARNING: Never place, or allow a child to place, the shoulder belt under a child’ s arm or behind the back because it reduces the protection for the upper part of the body and may increase the risk of injury or death in a collision.
NOTICE TO UTILITY V EHICLE AND T RUCK OWNERS Utility vehicles and trucks handle differently than passenger cars in the various driving conditions that are encountered on streets, highways and off-road.
V EHICLE CHARACTERISTICS 4WD System (if equipped) Y our vehicle may be equipped with a Four Wheel Drive (4WD) system. W ith the 4WD option, power will be delivered to the front wheels and distributed to the rear wheels as needed.
• Narrower — to provide greater maneuverability in tight spaces, particularly in off-road use. As a result of the above dimensional differences, SUV’ s and trucks often will have a higher center of gravity and a greater difference in center of gravity between the loaded and unloaded condition.
government test course. For example, a tire graded 150 would wear one and one-half (1 1 ⁄ 2 ) times as well on the government course as a tire graded 100.
• T ire Identification Number (TIN): A number on the sidewall of each tire providing information about the tire brand and manufacturing plant, tire size and date of manufacture. Also referred to as DOT code. • Inflation pressure: A measure of the amount of air in a tire.
At least once a month and before long trips, inspect each tire and check the tire pressure with a tire gauge (including spare, if equipped). Inflate all tires to the inflation pressure recommended by Ford Motor Company . Y ou are strongly urged to buy a reliable tire pressure gauge, as automatic service station gauges may be inaccurate.
T o check the pressure in your tire(s): 1. Make sure the tires are cool, meaning they are not hot from driving even a mile. If you are checking tire pressure when the tire is hot, (i.e. driven more than 1 mile [1.6 km]), never “bleed” or reduce air pressure.
the valve stem. Inspect the tire sidewalls for cracking, cuts, bruises and other signs of damage or excessive wear . If internal damage to the tire is suspected, have the tire demounted and inspected in case it needs to be repaired or replaced.
U.S. DOT Tire Identification Number (TIN) Both U.S. and Canada Federal regulations require tire manufacturers to place standardized information on the sidewall of all tires. This information identifies and describes the fundamental characteristics of the tire and also provides a U.
W ARNING: When mounting replacement tires and wheels, you should not exceed the maximum pressure indicated on the sidewall of the tire to set the beads without additional precautions listed below . If the beads do not seat at the maximum pressure indicated, re-lubricate and try again.
Safety practices Driving habits have a great deal to do with your tire mileage and safety . • Observe posted speed limits • A void fast starts, stops and turns • A void potholes and objects on the road • Do not run over curbs or hit the tire against a curb when parking W ARNING: If your vehicle is stuck in snow , mud, sand, etc.
Wheel misalignment in the front or the rear can cause uneven and rapid treadwear of your tires and should be corrected by an authorized dealer . Front wheel drive (FWD) vehicles and those with an independent rear suspension (if equipped) may require alignment of all four wheels.
• Rear Wheel Drive (RWD) vehicles/Four Wheel Drive (4WD)/All Wheel Drive (A WD) vehicles (front tires at top of diagram) Sometimes irregular tire wear can be corrected by rotating the tires.
Information on “P” type tires P215/65R15 95H is an example of a tire size, load index and speed rating. The definitions of these items are listed below . (Note that the tire size, load index and speed rating for your vehicle may be different from this example.
Note: Y ou may not find this information on all tires because it is not required by federal law . Letter rating Speed rating - mph (km/h) M 81 mph (130 km/h) N 87 mph (140 km/h) Q 99 mph (159 km/h) R .
11. Maximum Load: Indicates the maximum load in kilograms and pounds that can be carried by the tire. Refer to the Safety Compliance Certification Label, which is located on the B-Pillar or the edge of the driver’ s door , for the correct tire pressure for your vehicle.
Additional information contained on the tire sidewall for “L T” type tires “L T” type tires have some additional information beyond those of “P” type tires; these differences are described below . Note: T ire Quality Grades do not apply to this type of tire.
Information on “T” type tires “T” type tires have some additional information beyond those of “P” type tires; these differences are described below: T145/80D16 is an example of a tire size. Note: The temporary tire size for your vehicle may be different from this example.
TIRE PRESSURE MONITORING SYSTEM (TPMS) Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label.
following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. W ARNING: The T ire Pressure Monitoring System is NOT a substitute for manually checking tire pressure.
T o restore the full functionality of the Tire Pressure Monitoring System, have the damaged road wheel/tire repaired and remounted on your vehicle. For additional information, refer to Changing tires with TPMS in this section.
Low T ire Pressure W arning Light Possible cause Customer Action Required Flashing W arning Light Spare tire in use Y our temporary spare tire is in use.
SNOW TIRES AND CABLES W ARNING: Snow tires must be the same size, load index, speed rating as those originally provided by Ford. Use of any tire or wheel not recommended by Ford can affect the safety and performance of your vehicle, which could result in an increased risk of loss of vehicle control, vehicle rollover , personal injury and death.
V EHICLE LOADING – WITH AND WITHOUT A TRAILER This section will guide you in the proper loading of your vehicle and/or trailer , to keep your loaded vehicle weight within its design rating capability , with or without a trailer . Properly loading your vehicle will provide maximum return of vehicle design performance.
Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be found on the T ire Label on the B-Pillar or the edge of the driver’ s door (vehicles exported outside the US and Canada may not have a T ire Label).
Example only: Cargo W eight – includes all weight added to the Base Curb W eight, including cargo and optional equipment. When towing, trailer tongue load or king pin weight is also part of cargo weight. GA W (Gross Axle W eight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload.
GA WR (Gross Axle W eight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Label located on the B-Pillar or the edge of the driver’ s door .
• Example only: W ARNING: Exceeding the Safety Compliance Certification Label vehicle weight rating limits could result in substandard vehicle handling or performance, engine, transmission and/or structural damage, serious damage to the vehicle, loss of control and personal injury .
GCW (Gross Combined W eight) – is the weight of the loaded vehicle (GVW) plus the weight of the fully loaded trailer . GCWR (Gross Combined W eight Rating) – is the maximum allowable weight of the vehicle and the loaded trailer – including all cargo and passengers – that the vehicle can handle without risking damage.
W ARNING: Exceeding any vehicle weight rating limitation could result in serious damage to the vehicle and/or personal injury . Steps for determining the correct load limit: 1. Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lb.
cement to your home? If you and your friend each weigh 220 lb. (99 kg), the calculation would be: 1400 - (2 x 220) - (12 x 100) = 1400 - 440 - 1200 = - 240 lb. No, you do not have enough cargo capacity to carry that much weight. In metric units, the calculation would be: 6 3 5k g-( 2x9 9k g )-( 1 2x4 5k g )=6 3 5-1 9 8-5 4 0=- 1 0 3k g .
Follow these guidelines to ensure safe towing procedure: • Stay within your vehicle’ s load limits. • Thoroughly prepare your vehicle for towing. Refer to Preparing to tow in this chapter . • Use extra caution when driving while trailer towing.
4WD GCWR (Gross Combined W eight Rating)/T railer W eights Engine Maximum GCWR - lb (kg) T railer W eight Range - lb (kg) Maximum frontal area of trailer - ft 2 (m 2 ) 2.5L 5040 (2286) 1000 (454) 24 (2.2) Notes: For high altitude operation, reduce GCW by 2% per 1000 ft.
Safety chains Always connect the trailer’ s safety chains to hook retainers on the vehicle. T o connect the trailer’ s safety chains, cross the chains under the trailer tongue and allow slack for turning corners. If you use a rental trailer , follow the instructions that the rental agency gives to you.
• Consult your local motor vehicle speed regulations for towing a trailer . • Anticipate stops and brake gradually . • Do not exceed the GCWR rating or transmission damage may occur . Servicing after towing If you tow a trailer for long distances, your vehicle will require more frequent service intervals.
Exceeding these limits may allow water to enter vehicle components: • causing internal damage to the components. • affecting driveability , emissions and reliability . Replace the rear axle lubricant any time the axle has been submerged in water .
STARTING Positions of the ignition 1. Off— locks the gearshift lever and allows key removal. 2. Accessory— allows the electrical accessories such as the radio to operate while the vehicle is not running. 3. On— all electrical circuits operational and warning lights will illuminate.
Important safety precautions A computer system controls the engine’ s idle revolutions per minute (RPM). When the engine starts, the idle RPM runs higher than normal in order to warm the engine. If the engine idle speed does not slow down automatically , have the vehicle checked.
3. T urn the key to 3 (on) without turning the key to 4 (start). Some warning lights will briefly illuminate. See W arning lights and chimes in the Instrument Cluster chapter for more information regarding the warning lights. Starting the vehicle 1. T urn the key to 3 (on) without turning the key to 4 (start).
Note: After starting the vehicle, the engine may stop running to conserve fuel after it is warmed-up and the high voltage battery is sufficiently charged. Note: If the vehicle does not start, put the gearshift lever into P (Park), turn the ignition off, then attempt to start the vehicle again.
W ARNING: T o reduce the risk of electrical shock, do not use your heater with ungrounded electrical systems or two-pronged (cheater) adapters. Prior to using the engine block heater , follow these re.
How to use the engine block heater Ensure the receptacle terminals are clean and dry prior to use. T o clean them, use a dry cloth. Depending on the type of factory installed equipment, your engine block heater will use .4 to 1.0 kilowatt-hours of energy per hour of use.
Using ABS When hard braking is required, apply continuous force on the brake pedal; do not pump the brake pedal since this will reduce the effectiveness of the ABS and will increase your vehicle’ s stopping distance. The ABS will be activated immediately , allowing you to retain steering control during hard braking and on slippery surfaces.
Regenerative braking does not take the place of the standard friction brakes; it only assists them. Regenerative braking has also been designed to interact with the anti-lock brake system (ABS). Regenerative braking is disabled when the ABS is activated or the battery is fully charged.
Pull the release lever to release the brake. Driving with the parking brake on will cause the brakes to wear out quickly and reduce fuel economy . ADVANCET RAC 姞 WITH ROLL STABILITY CONTROL™ (RSC .
W ARNING: If a failure has been detected within the AdvanceT rac 威 with RSC 威 system, the “sliding car” icon will illuminate steadily . V erify that the AdvanceT rac 威 with RSC 威 system is not manually disabled (press the AdvanceT rac 威 with RSC 威 button located on the center of the instrument panel).
When AdvanceT rac 威 with RSC 威 performs a normal system self-check, some drivers may notice a rumble, grunting, or grinding noise after startup and when driving off.
or avoiding objects in the roadway . The ESC system operates by applying brakes to one or more of the wheels individually and, if necessary , reducing engine power if the system detects that the vehicle is about to skid or slide laterally . During ESC events the “sliding car” icon in the instrument cluster will flash.
AdvanceT rac 威 with RSC 威 button. Full features of the AdvanceT rac 威 with RSC 威 system can be restored by pressing the AdvanceT rac 威 with RSC 威 button again or by turning off and restarting the engine. If you switch off the traction control, the “sliding car” icon will illuminate steadily .
• loose or worn steering components. • improper steering alignment. A high crown in the road or high crosswinds may also make the steering seem to wander/pull. PREPARING TO DRIVE W ARNING: Utility vehicles have a significantly higher rollover rate than other types of vehicles.
If you cannot move the gearshift lever out of P (Park) with ignition in the on position and the brake pedal pressed, it is possible that a fuse has blown or the vehicle’ s brake lamps are not operating properly . Refer to Fuses and relays in the Roadside Emergencies chapter .
AUTOMATIC TRANSMISSION OPERATION Understanding the gearshift positions of the electronically-controlled Continuously V ariable T ransmission (eCVT) P (Park) This position locks the transmission and prevents the front wheels from turning. T o put your vehicle in gear: 1.
D (Drive) The normal driving position for the best fuel economy . L (Low) • Provides maximum engine braking. • The transmission may be shifted into L (Low) at any vehicle speed. W ARNING: When parking, do not use the gearshift in place of the parking brake.
W ARNING: T o help avoid personal injury , always use caution when in reverse and when using the RSS. W ARNING: This system is not designed to prevent contact with small or moving objects. The system is designed to provide a warning to assist the driver in detecting large stationary objects to avoid damaging the vehicle.
Note: If the system cannot be turned off, refer to MyKey™ in the Locks and Security chapter for more information. Keep the RSS sensors (located on the rear bumper/fascia) free from snow , ice and large accumulations of dirt (do not clean the sensors with sharp objects).
Image delay if displayed through the rearview mirror: When shifting out of R (Reverse) and into any other gear , the image in the rearview mirror will remain on for a few seconds before it shuts off to assist in parking or trailer hookup.
Night time and dark area use At night time or in dark areas, the camera relies on the reverse lamp lighting to produce an image. Therefore it is necessary that both reverse lamps are operating in order to get a clear image in the dark.
Automatic Search for Parking Space T o start, press the AP A control switch (on the instrument panel). The message center will display ACTIVE P ARK SEARCHING. T o designate what side of the street to search on, use the turn signal. The arrow symbols >> and << in the message center indicate on which side of the vehicle AP A will park.
Automatic Steering into Parking Space Automatic steering is activated when you stop the vehicle, remove your hands from the steering wheel and select the R (Reverse) gear .
AP A Finished When Active Park Assist has completed the automated steering, the message center displays ACTIVE P ARK FINISHED followed by a chime. The driver is responsible to assess and correct as necessary the final parking position and put the vehicle in P (Park).
T roubleshooting Why isn’ t APA searching for a parking space? • Y ou may have deactivated the AdvanceT rac 威 system. • One of the doors (except the driver’ s door) may not be securely closed. Why doesn’ t APA of fer a particular parking space? • Something may be contacting the front bumper or side sensors.
• One of the parked vehicles has a high altitude attachment (i.e. salt sprayer , snow plow , moving truck high bed, etc.) High altitude attachments may not be detected by the system. • The parking space length or parked objects position have changed after the vehicle has passed the parking space.
Driving with blind spot mirrors Before a lane change, check the main mirror first, then check the blind spot mirror . If no vehicles are present in the blind spot mirror and the traffic in the adjacent lane is at a safe distance, signal that you are going to change lanes.
Driving off-road with truck and utility vehicles 4WD vehicles are specially equipped for driving on sand, snow , mud and rough terrain and have operating characteristics that are somewhat different from conventional vehicles, both on and off the road.
• It often may be less risky to strike small objects, such as highway reflectors, with minor damage to your vehicle rather than attempt a sudden return to the pavement which could cause the vehicle to slide sideways out of control or roll over . Remember , your safety and the safety of others should be your primary concern.
Emergency maneuvers • In an unavoidable emergency situation where a sudden sharp turn must be made, remember to avoid “over -driving” your vehicle, i.e., turn the steering wheel only as rapidly and as far as required to avoid the emergency . Excessive steering will result in less vehicle control, not more.
Mud and water If you must drive through high water , drive slowly . T raction or brake capability may be limited. When driving through water , determine the depth; avoid water higher than the bottom of the hubs (if possible) and proceed slowly . If the ignition system gets wet, the vehicle may stall.
slopes or hills . A danger lies in losing traction, slipping sideways and possibly rolling over . Whenever driving on a hill, determine beforehand the route you will use. Do not drive over the crest of a hill without seeing what conditions are on the other side.
A void sudden braking as well. Although a 4WD vehicle may accelerate better than a two-wheel drive vehicle in snow and ice, it won’t stop any faster , because as in other vehicles, braking occurs at all four wheels. Do not become overconfident as to road conditions.
DRIVING THROUGH WATER If driving through deep or standing water is unavoidable, proceed very slowly especially when the depth is not known. Never drive through water that is higher than the bottom of the wheel rims (for cars) or the bottom of the hubs (for trucks).
ROADSIDE ASSISTANCE Getting roadside assistance T o fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program.
Canadian customers refer to your Customer Information Guide for information on: • coverage period • exact fuel amounts • towing of your disabled vehicle • emergency travel expense reimbursemen.
HAZARD FLASHER CONTROL The hazard flasher is located on the steering column, just behind the steering wheel. The hazard flashers will operate when the ignition is in any position or if the key is not in the ignition. Press in the flasher control and all front and rear direction signals will flash.
The fuel pump shut-off switch is located in the front passenger’ s footwell, behind a flip-up cover . The high voltage shut-off switch is located in the cargo area on the passenger side of the vehicle in the jack compartment, behind the jack access door .
If you see or smell fuel, do not reset the fuel pump shut-off or try to start your vehicle; you could injure yourself or others. Have all the passengers get out of the vehicle and call the local fire department or a towing service. FUSES AND RELAYS Fuses If electrical components in the vehicle are not working, a fuse may have blown.
Passenger compartment fuse panel The fuse panel is located on the right-hand side of the center console, by the instrument panel. Remove the panel cover to access the fuse cover .
The fuses are coded as follows: Fuse/Relay Location Fuse Amp Rating Protected Circuits 1 30A 110V inverter 2 15A Brake on/off switch 3 15A SYNC 威 module 4 30A Moon roof 5 10A Brake-shift i nterlock .
Fuse/Relay Location Fuse Amp Rating Protected Circuits 27 20A Ignition switch 28 5A Radio 29 5A Instrument panel cluster 30 5A Not used (spare) 31 10A Restraints control module 32 10A Rear video camer.
Power distribution box The power distribution box is located in the engine compartment. The power distribution box contains high-current fuses that protect your vehicle’ s main electrical systems from overloads. W ARNING: Always disconnect the low voltage (underhood) battery before servicing high current fuses.
Fuse/Relay Location Fuse Amp Rating Protected Circuits 4 40A** Electric vacuum pump 5 10A* Powertrain control module (PCM) – keep alive power , PCM relay , T ransmission control module, Canister ven.
Fuse/Relay Location Fuse Amp Rating Protected Circuits 28 15A* Universal exhaust gas oxygen (UEGO) sensor , PCM – emission related powertrain components malfunction indicator lamp 29 15A* PCM power .
Auxiliary relay box The relay box is located in the engine compartment on the radiator support bracket. Fuse/Relay location Fuse amp rating Description Relay — Electric vacuum pump (solid state) 1 .
CHANGING A FLAT TIRE If you get a flat tire while driving: • do not brake heavily . • gradually decrease the vehicle’ s speed. • hold the steering wheel firmly .
and type as the road tires and wheels that were originally provided by Ford. If the dissimilar spare tire or wheel is damaged, it should be replaced rather than repaired.
The usage of a full-size dissimilar spare tire/wheel can lead to impairment of the following: • Handling, stability and braking performance • Comfort and noise • Ground clearance and parking at .
Removing the jack and tools The jack and tools are located in the right rear of the cargo area behind an access panel. T o remove jack from vehicle: 1. Release the thumbscrew on the bracket. 2. Release the retention clip on the upper part of the jack bracket.
Removing the spare tire or spare tire and tether (if equipped) 1. Insert the lug wrench through the access hole in the rear bumper . 2. T urn the handle counterclockwise and lower the spare tire until it can be slid rearward and the cable is slack. 3.
6. If not replacing the spare or flat tire to the underbody storage area, raise winch up into the installed position. 7. Use the attached fastener strap (2) to tie the tether end to the winch actuator shaft (if equipped).
2. Loosen each wheel lug nut one-half turn counterclockwise but do not remove them until the wheel is raised off the ground. Before placing the jack under the vehicle, NOTE the jack locations: • Front View shown from rear of front tire. Position the jack directly below the protruding bolt.
• Rear View shown from forward of rear tire. Position the jack directly below the stud on the rear trailing arm. 3. Position the jack according to the guides and turn the jack handle clockwise until the tire is a maximum of 1 inch (25 mm) off the ground.
Never use the differentials as a jacking point. W ARNING: T o lessen the risk of personal injury , do not put any part of your body under the vehicle while changing a tire. Do not start the engine when your vehicle is on the jack. The jack is only meant for changing the tire.
• guide the jack bottom first in the trim opening and position in the bracket (3), • secure the retention clip on the upper part of the jack (2), and • close the thumbscrew (1). Make sure the jack is fastened so it does not rattle when you drive.
4. Slide the wheel partially under the vehicle and install the retainer through the center of the wheel. 5. T urn the jack handle clockwise until the tire is raised to its original position underneath the vehicle. The effort to turn the jack handle increases significantly as the tire contacts the frame.
Note: Inspect the wheel pilot hole prior to installation. If there is visible corrosion in wheel pilot hole, remove loose particles by wiping with clean rag and apply grease. Apply grease only to the wheel pilot hole surface by smearing a “dime” (1 square cm) sized glob of grease around the wheel pilot surface (1) with end of finger .
Preparing your vehicle If your low voltage (underhood) battery becomes disconnected or disabled for any reason, the vehicle controller must relearn the engine’ s operating characteristics in order to operate it at maximum efficiency . This relearning process occurs the first time the vehicle is driven after reconnecting the low voltage battery .
Connecting the jumper cables 1. Connect the positive (+) jumper cable to the positive (+) terminal of the discharged battery . Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery . 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery .
3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery . 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’ s engine, away from the battery and the carburetor/fuel injection system.
Jump starting 1. Start the engine of the booster vehicle and run the engine at moderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for an additional three minutes before disconnecting the jumper cables.
3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’ s battery . 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’ s battery .
WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or , if you are a member of a roadside assistance program, your roadside assistance service provider . It is recommended that your vehicle be towed with a wheel lift and dollies or flatbed equipment.
Ford Motor Company produces a towing manual for all authorized tow truck operators. Have your tow truck operator refer to this manual for proper hook-up and towing procedures for your vehicle. If the vehicle is towed by other means or incorrectly , vehicle damage may occur .
GETTING THE SERVICES YOU NEED W arranty repairs to your vehicle must be performed by an authorized Ford, Lincoln, or Mercury dealer . While any authorized dealer handling your vehicle line will provide warranty service, we recommend you return to your selling authorized dealer who wants to ensure your continued satisfaction.
In Canada: Mailing address (Ford vehicles) Customer Relationship Centre Ford Motor Company of Canada, Limited P .O. Box 2000 Oakville, Ontario L6J 5E4 T elephone 1-800-565-3673 (FORD) Online www .ford.ca Mailing address (Lincoln vehicles) Lincoln Centre Ford Motor Company of Canada, Limited P .
In the United States, a warranty dispute must be submitted to the BBB AUTO LINE before taking action under the Magnuson-Moss W arranty Act, or to the extent allowed by state law , before pursuing replacement or repurchase remedies provided by certain state laws.
THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM (U.S. ONLY) Y our satisfaction is important to Ford Motor Company and to your dealer . If a warranty concern has not been resolved using the three-step procedure outlined on the first page of the Customer Assistance section, you may be eligible to participate in the BBB AUTO LINE program.
UTILIZING THE MEDIATION/ARBITRATION PROGRAM (CANADA ONLY) For vehicles delivered to authorized Canadian dealers. In those cases where you continue to feel that the efforts by Ford of Canada and the au.
If your vehicle must be serviced while you are traveling or living in Central America, the Caribbean, or the Middle East, contact the nearest authorized dealer . If the authorized dealer cannot help you, contact: FORD MOTOR COMP ANY FORD EXPORT OPERA TIONS 1555 Fairlane Drive Fairlane Business Park #3 Allen Park, Michigan 48101 U.
Obtaining a French Owner ’ s Guide French Owner’ s Guides can be obtained from your authorized dealer or by writing to: Ford Motor Company of Canada, Limited Service Publications CHQ202 The Canadian Road P .O. Box 2000 Oakville, ON, Canada L6J 5E4 REPORTING SAFETY DEFECTS (U.
W ASHING THE EXTERIOR W ash your vehicle regularly with cool or lukewarm water and a neutral pH shampoo, such as Motorcraft 威 Detail W ash (ZC-3-A), which is available from your authorized dealer . • Never use strong household detergents or soap, such as dish washing or laundry liquid.
W AXING • W ash the vehicle first. • Do not use waxes that contain abrasives; use Motorcraft 威 Premium Liquid W ax (ZC-53-A), which is available from your authorized dealer , or an equivalent quality product.
ENGINE Engines are more efficient when they are clean because grease and dirt buildup keep the engine warmer than normal. When washing: • T ake care when using a power washer to clean the engine. The high-pressure fluid could penetrate the sealed parts and cause damage.
PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products are available from your authorized dealer . • For routine cleaning, use Motorcraft 威 Detail W ash (ZC-3-A). • If tar or grease spots are present, use Motorcraft 威 Bug and T ar Remover (ZC-42).
• A void cleaners or polishes that increase the gloss of the upper portion of the instrument panel. The dull finish in this area helps protect the driver from undesirable windshield reflection.
• If a ring forms on the fabric after spot cleaning, clean the entire area immediately (but do not oversaturate) or the ring will set. • Do not use household cleaning products or glass cleaners, which can stain and discolor the fabric and affect the flame retardant abilities of the seat materials.
FORD AND LINCOLN MERCURY CAR CARE PRODUCTS Y our Ford or Lincoln Mercury authorized dealer has many quality products available to clean your vehicle and protect its finishes. These quality products have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and appearance of your vehicle.
SERVICE RECOMMENDATIONS T o help you service your vehicle, we provide scheduled maintenance information which makes tracking routine service easy . If your vehicle requires professional service, your authorized dealer can provide the necessary parts and service.
1. High voltage connector shield 2. Service disconnect 3. High voltage battery case Working with the engine off 1. Set the parking brake and ensure the gearshift is securely latched in P (Park). 2. T urn off the engine and remove the key . 3. Block the wheels to prevent the vehicle from moving unexpectedly .
OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the bottom of the instrument panel. 2. At the front of the vehicle, lift up on the auxiliary latch handle located in the center between the hood and the grille. 3. Lift the hood open and secure it with the prop rod.
WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if the level is low . In very cold weather , do not fill the reservoir completely . Only use a washer fluid that meets Ford specifications. Do not use any special washer fluid such as windshield water repellent type fluid or bug wash.
Checking and adding washer fluid for the liftgate W asher fluid for the liftgate is supplied by the same reservoir as the windshield. CHANGING THE WIPER BLADES 1. Pull the wiper blade and arm away from the glass. 2. Squeeze the locking tabs to release the blade from the arm and pull the blade away from the arm to remove it.
Changing rear window wiper blade The rear wiper arm is designed without a service position. This reduces the risk of damage to the blade in an automatic car wash. T o replace the wiper blade: 1. Grab the wiper arm with one hand close to the arm/blade joint and pull it as far away from the glass as possible.
5. Locate and carefully remove the engine oil level dipstick. 6. W ipe the dipstick clean. Insert the dipstick fully , then remove it again. • If the oil level is within the lower and upper holes/lines, the oil level is acceptable.
3. Recheck the engine oil level. Make sure the oil level is not above the full mark on the engine oil level dipstick. 4. Install the dipstick and ensure it is fully seated. 5. Fully install the engine oil filler cap by turning the filler cap clockwise 1/4 of a turn until it is seated.
and may result in severe engine damage. The customer warranty may be void for any damage to the engine if the O-rings are not replaced. Ford production and Motorcraft 威 replacement oil filters are designed for added engine protection and long life.
W ARNING: When lifting a plastic-cased battery , excessive pressure on the end walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery . Lift the battery with a battery carrier or with your hands on opposite corners.
If the battery has been disconnected or a new battery has been installed, the clock and the preset radio stations must be reset once the battery is reconnected. • Always dispose of automotive batteries in a responsible manner . Follow your local authorized standards for disposal.
Checking engine coolant The concentration and level of engine coolant should be checked at the intervals listed in scheduled maintenance information . The coolant concentration should be maintained at 50/50 coolant and distilled water , which equates to a freeze point of -34°F (-36°C).
Checking motor/electronics (M/E) coolant The M/E coolant reservoir is located behind the engine coolant reservoir . Refer to the following engine coolant sections for all information, instructions and warnings related to cooling systems.
If the engine coolant has not been checked at the recommended interval, the engine coolant reservoir may become low or empty . If the reservoir is low or empty , add engine coolant to the reservoir .
For vehicles with overflow coolant systems with a non-pressurized cap on the coolant recovery system, add coolant to the coolant recovery reservoir when the engine is cool.
Y our cooling system may have a leak. Operating an engine with a low level of coolant can result in engine overheating and possible engine damage. Recycled engine coolant Ford Motor Company does NOT recommend the use of recycled engine coolant since a Ford-approved recycling process is not yet available.
• Refer to the chart on the coolant container to ensure the coolant concentration in your vehicle will provide adequate protection at the temperatures in which you drive. V ehicles driven year -round in non-extreme climates should use a 50/50 mixture of engine coolant and distilled water for optimum cooling system and engine protection.
• Automotive fuels can be harmful or fatal if swallowed. Fuel such as gasoline is highly toxic and if swallowed can cause death or permanent injury . If fuel is swallowed, call a physician immediately , even if no symptoms are immediately apparent. The toxic effects of fuel may not be visible for hours.
Refueling W ARNING: Fuel vapor burns violently and a fuel fire can cause severe injuries. T o help avoid injuries to you and others: • Read and follow all the instructions on the pump island; • T .
Note: A fuel spillage concern may occur if overfilling the fuel tank. Do not overfill the tank to the point that the fuel is able to bypass the fuel filler nozzle. The overfilled fuel may run down the drain located below and in front of the fuel filler door .
Y our vehicle was not designed to use fuel or fuel additives with metallic compounds, including manganese-based additives. Note: Use of any fuel other than those recommended may cause powertrain damage, a loss of vehicle performance, and repairs may not be covered under warranty .
Running out of fuel A void running out of fuel because this situation may have an adverse effect on powertrain components. If you have run out of fuel: • Y ou may need to cycle the ignition from off to on several times after refueling to allow the fuel system to pump the fuel from the tank to the engine.
1. Locate the white plastic funnel. It is attached to the inside of the rear passenger side cargo compartment access door . 2. Slowly insert the funnel into the Easy Fuel™ system. 3. Fill the vehicle with fuel from the portable fuel container . 4. When done, clean the funnel or properly dispose of it.
Filling the tank When the fuel gauge indicates empty , there is still a small reserve of fuel in the fuel system. When refueling your vehicle after the fuel gauge indicates empty , you might not be able to refuel the full amount of the advertised capacity of the fuel tank due to the empty reserve still present in the tank.
Driving style — good driving and fuel economy habits Since it is able to operate in electric mode and to collect braking energy , your hybrid vehicle may get better fuel economy in city driving than on the highway . This is contrary to conventional vehicles.
Conditions • Heavily loading a vehicle or towing a trailer may reduce fuel economy at any speed. • Carrying unnecessary weight may reduce fuel economy (approximately 1 mpg [0.
W ARNING: Do not park, idle, or drive your vehicle in dry grass or other dry ground cover . The emission system heats up the engine compartment and exhaust system, which can start a fire.
3. The fuel fill inlet may not have been properly closed. See Easy Fuel™ “no cap” fuel system in this chapter . 4. Driving through deep water—the electrical system may be wet.
vehicle is not ready for I/M testing, the following driving cycle consisting of mixed city and highway driving may be performed: 15 minutes of steady driving on an expressway/highway followed by 20 minutes of stop-and-go driving with at least four 30-second idle periods.
AIR FILTER Refer to scheduled maintenance information for the appropriate intervals for changing the air filter element. When changing the air filter element, use only the air filter element listed. Refer to Motorcraft 威 part numbers in this chapter .
MOTORCRAFT PART NUMBERS Component 2.5L I4 engine Oil filter FL-910 Spark plugs 1 Engine air filter element F A-1772 2 Cabin air filter FP-66 Low voltage (underhood) battery BXT -96R 1 For spark plug replacement, see your authorized dealer .
MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIES Item Capacity Ford Part Name or equivalent Ford Part Number / Ford Specification Brake fluid Between MIN and MAX lines on reservoir Motorcraft 威 Hig.
Item Capacity Ford Part Name or equivalent Ford Part Number / Ford Specification Engine oil 5.3 quarts (5.0L) • Motorcraft 威 SAE 5W -20 Premium Synthetic Blend Motor Oil (US) • Motorcraft 威 SA.
Item Capacity Ford Part Name or equivalent Ford Part Number / Ford Specification W indshield washer fluid 4.7 quarts (4.5L) Motorcraft 威 Premium W indshield W asher Concentrate ZC-32-A / WSB-M8B16-A2 Fuel tank 15 gallons (56.8L) —— 1 Add the coolant type originally equipped in your vehicle.
ENGINE DATA Engine 2.5L I4 engine Cubic inches 152 Required fuel 87 octane Firing order 1-3-4-2 Ignition system Coil on plug Spark plug gap 0.049–0.053 inch (1.
IDENTIFYING YOUR VEHICLE Safety Compliance Certification Label The National Highway T raffic Safety Administration Regulations require that a Safety Compliance Certification Label be affixed to a vehicle and prescribe where the Safety Compliance Certification Label may be located.
The V ehicle Identification Number (VIN) contains the following information: 1. W orld manufacturer identifier 2. Brake system / Gross V ehicle W eight Rating (GVWR) / Restraint Devices and their location 3. Make, vehicle line, series, body type 4. Engine type 5.
GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for your vehicle through your local Ford or Ford of Canada dealer .
Peace of mind Keyless entry keypad Wheel locks For maximum vehicle performance, keep the following information in mind when adding accessories or equipment to your vehicle: • When adding accessories.
GENERAL MAINTENANCE INFORMATION Why maintain your vehicle? This guide describes the scheduled maintenance required for your vehicle. Carefully following this schedule helps protect against major repair expenses resulting from neglect or inadequate maintenance and may also help to increase the value of your vehicle when you sell or trade it.
Ford strongly recommends the use of genuine Ford replacement parts. Parts other than Ford, Motorcraft 威 or Ford authorized remanufactured parts that are used for maintenance replacement or for the service of components affecting emission control must be equivalent to genuine Ford Motor Company parts in performance and durability .
Genuine Ford Parts and Service When planning your maintenance services, consider your Ford and Lincoln Mercury dealership for all your vehicle’ s needs.
WHICH MAINTENANCE SCHEDULE SHOULD Y OU FOLLOW? Owner Checks and Services Refer to Mileage Intervals for Additional Checks and Services Certain basic maintenance checks and inspections should be performed by the owner or a service technician at the intervals indicated.
Multi-point Inspection In order to keep your vehicle running right, it is important that you have the systems on your vehicle checked regularly . This can help identify any potential issue before there are any problems.
U.S. AND CANADIAN SCHEDULE 5,000 miles (8,000 km) ❑ Inspect tires for wear and measure tread depth ❑ Rotate tires D EALER V ALIDATION : RO#: P&A C ODE : D ATE :M ILEAGE : 10,000 miles (16,000 .
30,000 miles (48,000 km) ❑ Change engine oil and replace oil filter ❑ Inspect tires for wear and measure tread depth ❑ Rotate tires ❑ Inspect wheel ends for end play and noise ❑ Replace engi.
60,000 miles (96,000 km) ❑ Change engine oil and replace oil filter ❑ Inspect tires for wear and measure tread depth ❑ Rotate tires ❑ Inspect wheel ends for end play and noise ❑ Inspect brak.
90,000 miles (144,000 km) ❑ Change engine oil and replace oil filter ❑ Inspect tires for wear and measure tread depth ❑ Rotate tires ❑ Inspect wheel ends for end play and noise ❑ Replace eng.
120,000 miles (192,000 km) ❑ Change engine oil and replace oil filter ❑ Inspect tires for wear and measure tread depth ❑ Rotate tires ❑ Inspect wheel ends for end play and noise ❑ Inspect br.
SPECIAL OPERATING CONDITIONS T owing a trailer or using a camper or car-top carrier Every 5,000 miles, 6 months or 200 hours of engine operation (whichever comes first) Change engine oil and replace f.
Operating in dusty conditions such as unpaved or dusty roads Every 5,000 miles, 6 months or 200 hours of engine operation (whichever comes first) Change engine oil and replace filter Inspect tires and.
Special Operating Conditions Log D EALER V ALIDATION : RO#: P&A C ODE : D ATE :M ILEAGE : D EALER V ALIDATION : RO#: P&A C ODE : D ATE :M ILEAGE : D EALER V ALIDATION : RO#: P&A C ODE : D .
Special Operating Conditions Log D EALER V ALIDATION : RO#: P&A C ODE : D ATE :M ILEAGE : D EALER V ALIDATION : RO#: P&A C ODE : D ATE :M ILEAGE : D EALER V ALIDATION : RO#: P&A C ODE : D .
Current mileage goes here => Add 50,000 miles to the current miles + 50,000 Next change due at this mileage => Or T oday’s date goes here => Add 3 years + 00 / 00 / 03 Date of next change => whichever comes first Dealer Stamp P & A CODE R.
Current mileage goes here => Add 50,000 miles to the current miles + 50,000 Next change due at this mileage => Or T oday’s date goes here => Add 3 years + 00 / 00 / 03 Date of next change => whichever comes first Dealer Stamp P & A CODE R.
FORD ESP EXTENDED SERVICE PLANS More than 30 million Ford, Lincoln, and Mercury owners have discovered the powerful protection of Ford ESP . It is the only extended service plan backed by Ford Motor Company , and provides “peace of mind” protection beyond the New V ehicle Limited W arranty coverage.
Ford ESP Can Quickly Pay for Itself One service bill – the cost of parts and labor – can easily exceed the price of your Ford ESP Service Contract.
Ford Extended Service Plan 345 2010 Escape Hybrid (ehv) Owners Guide, 1st Printing USA (fus).
A Accessory delay .......................... 77 Active Park Assist .....................229 AdvanceT rac .............................. 217 Air cleaner filter ............... 317–318 Air conditioning automatic temperature control system ............
Child safety seats ......................160 attaching with tether straps ....................................... 167 in front seat ............................ 161 in rear seat .............................. 161 LA TCH ...............................
filter , specifications ........295, 318 recommendations ................... 295 refill capacities ........................ 319 specifications .......................... 319 Event data recording .................. 14 Exhaust fumes ....................
J Jump-starting your vehicle ......266 K Keyless entry system autolock ............................... 96, 98 keypad ..................................... 104 locking and unlocking doors ........................................ 105 programming entry code .
Parts (see Motorcraft 威 parts) ........... 318 Passenger Occupant Classification Sensor ................. 128 Power distribution box (see Fuses) ............................... 251 Power door locks ........................ 96 Power mirrors .........
SecuriLock passive anti-theft system ........................................ 106 Servicing your vehicle .............. 288 Setting the clock ......................... 34 Snowplowing ............................... 13 SOS Post Crash Alert ............
W W arning lights (see Lights) ....... 18 W asher fluid .............................. 291 W ater , Driving through ............. 242 W indows power ......................................... 76 rear wiper/washer ..................... 70 W indshield washer fluid and wipers .
Een belangrijk punt na aankoop van elk apparaat Ford 2010 Escape Hybrid (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Ford 2010 Escape Hybrid heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Ford 2010 Escape Hybrid vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Ford 2010 Escape Hybrid leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Ford 2010 Escape Hybrid krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Ford 2010 Escape Hybrid bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Ford 2010 Escape Hybrid kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Ford 2010 Escape Hybrid . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
