Gebruiksaanwijzing /service van het product 2010 F-150 van de fabrikant Ford
Ga naar pagina of 419
Introduction 4 Instrument Cluster 12 W arning lights and chimes 12 Gauges 18 Message center 22 Entertainment Systems 40 AM/FM stereo 40 AM/FM stereo with CD/MP3 42 Auxiliary input jack (Line in) 50 US.
Locks and Security 126 Keys 126 Locks 126 Anti-theft system 138 Seating and Safety Restraints 147 Seating 147 Safety restraints 166 Airbags 185 Child restraints 199 Tires, Wheels and Loading 223 T ire.
Customer Assistance 346 Reporting safety defects (U.S. only) 352 Reporting safety defects (Canada only) 352 Cleaning 353 Maintenance and Specifications 363 Engine compartment 365 Engine oil 368 Batter.
CONGRATULATIONS Congratulations on acquiring your new Ford Motor Company product. Please take the time to get well acquainted with your vehicle by reading this handbook. The more you know and understand about your vehicle, the greater the safety and pleasure you will derive from driving it.
Protecting the environment W e must all play our part in protecting the environment. Correct vehicle usage and the authorized disposal of waste, cleaning and lubrication materials are significant steps towards this aim. Information in this respect is highlighted in this guide with the tree symbol.
SPECIAL NOTICES New V ehicle Limited W arranty For a detailed description of what is covered and what is not covered by your vehicle’ s New V ehicle Limited W arranty , refer to the Warranty Guide/Customer Information Guide that is provided to you along with your Owner’ s Guide.
NOTICE TO OWNERS OF THE F150 Note: Y our vehicle is equipped with high performance tires. When first driving the vehicle after it has been parked for a period of time, you may experience a temporary ride disturbance. This is a characteristic of the tires and should be no reason for concern.
T o access this information, special equipment must be directly connected to the recording modules. Ford Motor Company and Ford of Canada do not access event data recorder information without obtainin.
W ARNING: Driving while distracted can result in loss of vehicle control, accident and injury . Ford strongly recommends that drivers use extreme caution when using any device that may take their focus off the road. The driver’ s primary responsibility is the safe operation of their vehicle.
These are some of the symbols you may see on your vehicle. V ehicle Symbol Glossary Safety Alert See Owner’ s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat Lower Anchor Child Seat.
V ehicle Symbol Glossary Power W indows Front/Rear Power W indow Lockout Child Safety Door Lock/Unlock Interior Luggage Compartment Release Panic Alarm Engine Oil Engine Coolant Engine Coolant T emper.
W ARNING LIGHTS AND CHIMES Standard instrument cluster Platinum instrument cluster Instrument Cluster 12 2010 F-150 (f12) Owners Guide, 1st Printing USA (fus).
Harley Davidson instrument cluster W arning lights and gauges can alert you to a vehicle condition that may become serious enough to cause expensive repairs. A warning light may illuminate when a problem exists with one of your vehicle’ s functions.
Solid illumination after the engine is started indicates the On Board Diagnostics System (OBD-II) has detected a malfunction. Refer to On board diagnostics (OBD-II) in the Maintenance and Specifications chapter . If the light is blinking, engine misfire is occurring which could damage your catalytic converter .
W ARNING: Driving a vehicle with the brake system warning light on is dangerous. A significant decrease in braking performance may occur . It will take you longer to stop the vehicle.
Door ajar (R TT): Displays when the ignition is in the on position and any door is open. Engine coolant temperature (R TT): Illuminates when the engine coolant temperature is high. Stop the vehicle as soon as possible, switch off the engine and let cool.
AdvanceT rac 威 /T raction control (R TT) (if equipped): Displays when the AdvanceT rac 威 /T raction control is active. If the light remains on, have the system serviced immediately , refer to the Driving chapter for more information. 4X2 (R TT) (if equipped): Displays momentarily when two-wheel drive high is selected.
Anti-theft system: Flashes when the SecuriLock 威 Passive Anti-theft System has been activated. T urn signal: Illuminates when the left or right turn signal or the hazard lights are turned on. If the indicators stay on or flash faster , check for a burned out bulb.
Platinum instrument cluster Harley Davidson instrument cluster Instrument Cluster 19 2010 F-150 (f12) Owners Guide, 1st Printing USA (fus).
Speedometer: Indicates the current vehicle speed. Engine coolant temperature gauge: Indicates engine coolant temperature. At normal operating temperature, the needle will be in the normal range (between “H” and “C”). If it enters the red section, the engine is overheating.
T achometer (if equipped): Indicates the engine speed in revolutions per minute. Driving with your tachometer pointer continuously at the top of the scale may damage the engine. Engine oil pressure gauge: Indicates engine oil pressure. The needle should stay in the normal operating range (between “L” and “H”).
Y ellow area (warning) — the transmission fluid is higher than normal operating temperature. This can be caused by special operation conditions (i.e. snowplowing, towing or off road use). Refer to Special Operating Conditions in the scheduled maintenance information for instructions.
MYKEY MILES (km) (if programmed) For more information, refer to MyKey™ in the Locks and Security chapter . MILES (km) TO E This displays an estimate of approximately how far you can drive with the fuel remaining in your tank under normal driving conditions.
HOLD RESET FOR SETUP MENU Press and hold the SELECT/RESET stem when this message is displayed to get into the SETUP menu. The following setup items are available: OIL LIFE This displays the remaining oil life. An oil change is required whenever indicated by the message center and according to the recommended maintenance schedule.
Press the SELECT/RESET stem to turn autounlock on or off. EASY ENTR Y (if equipped) This feature automatically moves the driver’ s seat backwards for easy exit/entry from the vehicle. Press the SELECT/RESET stem to turn the easy entry/exit seat on or off.
1. XXX% OIL LIFE 2. CHARGING SYSTEM 3. DOOR ST A TUS 4. BRAKE SYSTEM 5. XX MILES TO E FUEL LEVEL XXX 6. TBC GAIN = XX.X NO TRAILER (if equipped and no trailer connected) 7. TBC GAIN = XX.X OUTPUT = ////// (if equipped and trailer connected) 8. MYKEY DIST ANCE (if programmed) 9.
REAR LEFT DOOR AJAR — Displayed when the rear left door is not completely closed. REAR RIGHT DOOR AJAR — Displayed when the rear right door is not completely closed. XXX MILES TO E FUEL LEVEL LOW — Displayed as an early reminder of a low fuel condition.
OIL CHANGE REQUIRED — Displayed when an oil change is required. XX%OIL LIFE CHANGE SOON —Displayed when an oil change will soon be required and shows the percentage of oil life left. WIRING F AUL T ON TRAILER (if equipped) — Displayed if there are certain faults in the vehicle wiring and trailer wiring/brake system.
SHIFT DELA YED PULL FOR W ARD (if equipped) — May display when shifting to or from 4X4 LOW . For more information, refer to Four -wheel drive (4WD) operation in the Driving chapter . TRAILER CONNECTED (if equipped) — Displayed when a correct trailer connection (a trailer with electric trailer brakes) is sensed during a given ignition cycle.
CHECK SPEED DRIVE SAFEL Y — Displayed when a MyKey™ is in use and the optional setting is on and the vehicle exceeds a preselected speed. Refer to MyKey™ in the Locks and Security chapter for more information.
Refer to UNITS later in this section to switch the display from Metric to English. MYKEY MILES (km) (If programmed) For more information, refer to MyKey™ in the Locks and Security chapter . MILES (km) TO E This displays an estimate of approximately how far you can drive with the fuel remaining in your tank under normal driving conditions.
For more information refer to Essentials of good fuel economy in the Maintenance and Specifications chapter . MPG (L/km) This displays instantaneous fuel economy as a bar graph ranging from ↓ poor economy to ↑ excellent economy . Y our vehicle must be moving to calculate instantaneous fuel economy .
9. MYKEY(S) PROGRAMMED 10. ADMIN KEYS PROGRAMMED OIL LIFE This displays the remaining oil life. An oil change is required whenever indicated by the message center and according to the recommended maintenance schedule. USE ONL Y RECOMMENDED ENGINE OILS.
AUTOUNLOCK This feature automatically unlocks all vehicle doors when the driver’ s door is opened within 10 minutes of the ignition being turned off. Press the RESET button to turn autounlock on or off. RUNNING BOARDS (if equipped) This feature automatically deploys the side running boards for easy entry/exit from the vehicle or for cleaning.
W aiting four seconds or pressing the RESET button cycles the message center through each of the language choices. Press the RESET button to set the language choice. System warnings System warnings alert you to possible problems or malfunctions in your vehicle’ s operating systems.
CHECK CHARGING SYSTEM — Displayed when the electrical system is not maintaining proper voltage. If you are operating electrical accessories when the engine is idling at a low speed, turn off as many of the electrical loads as soon as possible.
WIRING F AUL T ON TRAILER (if equipped) — Displayed if there are certain faults in the vehicle wiring and trailer wiring/brake system. Refer to T railer towing in the T ires, Wheels and Loading chapter for more information.
TRAIN RIGHT FRONT TIRE (if equipped) — Displayed when training the TPMS system. Refer to TPMS reset procedure in the T ires, Wheels and Loading chapter for more information. TRAIN RIGHT REAR TIRE (if equipped) — Displayed when training the TPMS system.
BUCKLE UP TO UNMUTE AUDIO — Displayed when a MyKey™ is in use and Belt-Minder 威 is activated. Refer to MyKey™ in the Locks and Security chapter for more information. ADVTRAC ON MYKEY SETTING — Displayed when a MyKey™ is in use when trying to disable the AdvanceT rac 威 system and the optional setting is on.
AUDIO SYSTEMS Note: If your volume is muted and MYKEY VOLUME LIMITED is displayed, refer to MyKey™ in the Locks and Security chapter for more information. AM/FM stereo system (if equipped) W ARNING: Driving while distracted can result in loss of vehicle control, accident and injury .
1. / : Press / to manually go up or down the radio frequency . Press and hold for a fast advance through radio frequencies. Also use in AUDIO mode to gain access to various settings. 2. AUDIO: Press AUDIO repeatedly to gain access to the following settings: BAL (Balance): Press AUDIO to reach the balance setting.
6. ON/OFF/V olume: Press VOL-PUSH to turn ON/OFF . T urn VOL-PUSH to increase/decrease volume. 7. CLK (Clock): Press CLK to toggle between displaying the radio frequency and the clock setting. Setting the clock: Press and hold CLK until the hours begin to flash.
W ARNING: Driving while distracted can result in loss of vehicle control, accident and injury . Ford strongly recommends that drivers use extreme caution when using any device that may take their focus off the road. The driver’ s primary responsibility is the safe operation of their vehicle.
SEEK: Press SEEK to access the previous/next strong radio station. SCAN: Press for a brief sampling of all strong radio stations. 0–9 (MEMOR Y PRESETS): When tuned to any station, press and hold a preset button until sound returns and PRESET # SA VED appears in the display .
CD/MP3 Player CD: Press to enter CD/MP3 mode. If a disc is already loaded into the system, CD/MP3 play will begin where it ended last. If no CD is loaded, NO DISC will appear in the display . LOAD: For a single CD system– This control is not operational.
SCAN: Press for a brief sampling of all tracks on the current disc or MP3 folder . DIRECT : In CD mode– Press DIRECT . The display will read DIRECT TRACK MODE SELECT TRACK. Enter the desired track number using the memory preset buttons (0–9). The system will then begin playing that track.
cancel your entry by pressing DIRECT . If an invalid station number is entered, INV ALID CHANNEL will appear in the display and the system will continue playing the current station. SEEK: Press SEEK to seek to the previous/next channel. If a specific category is selected, (Jazz, Rock, News, etc.
display . After a category is selected, press SEEK to search for that specific category of channels only (i.e. ROCK). Y ou may also select CA TEGORY ALL to seek all available SIRIUS categories and channels. Press OK to close and return to the main menu.
• CHANNEL LOCKOUT MENU- Press OK to enter the Channel Lockout menu. Press the to scroll through the following options: a. LOCK/UNLOCK THIS CHANNEL: Press OK when LOCK/UNLOCK THIS CHANNEL is displayed and the display will read ENTER PIN.
Use SEEK to adjust between SPEED OFF and levels 1–7: Increasing the level from 1 (lowest setting) to 7 (highest setting) allows the radio volume to automatically change slightly with vehicle speed to compensate for road and wind noise. Recommended level is 1–3; SPEED OFF turns the feature off and level 7 is the maximum setting.
The Auxiliary Input Jack provides a way to connect your portable music player to the in-vehicle audio system. This allows the audio from a portable music player to be played through the vehicle speakers with high fidelity .
2. Do not set the portable music player’ s volume level higher than is necessary to match the volume of the CD or FM radio in your audio system as this will cause distortion and will reduce sound quality . Many portable music players have different output levels, so not all players should be set at the same levels.
GENERAL AUDIO INFORMATION Radio frequencies: AM and FM frequencies are established by the Federal Communications Commission (FCC) and the Canadian Radio and T elecommunications Commission (CRTC). Those frequencies are: AM: 530, 540–1700, 1710 kHz FM: 87.
CD units are designed to play commercially pressed 4.75 in (12 cm) audio compact discs only . Due to technical incompatibility , certain recordable and re-recordable compact discs may not function correctly when used in Ford CD players. Do not use any irregular shaped CDs or discs with a scratch protection film attached.
Sample MP3 structure If you are burning your own MP3 discs, it is important to understand how the system will read the structures you create. While various files may be present, (files with extensions other than mp3), only files with the .mp3 extension will be played.
• T errain: Hills, mountains, tall buildings, bridges, tunnels, freeway overpasses, parking garages, dense tree foliage and thunderstorms can interfere with your reception. • Station overload: When you pass a ground based broadcast repeating tower , a stronger signal may overtake a weaker one and result in an audio mute.
Radio Display Condition Action Required ACQUIRING Radio requires more than two seconds to produce audio for the selected channel. No action required. This message should disappear shortly .
Radio Display Condition Action Required NO TEXT Category information not available. Category information not available at this time on this channel. The system is working properly . NO SIGNAL Loss of signal from the SIRIUS 威 satellite or SIRIUS 威 tower to the vehicle antenna.
SINGLE ZONE CLIMATE CONTROL 1. Defrost: Distributes outside air through the windshield defroster vents and de-mister vents. Can be used to clear the windshield of fog and thin ice. The system will automatically provide outside air to reduce window fogging.
4. A/C: Press to activate/deactivate air conditioning. Use with recirculated air to improve cooling performance and efficiency . A/C engages automatically in MAX A/C, (defrost) and (floor/defrost). 5. Recirculated air: Press to activate/deactivate air recirculation in the vehicle.
• T o improve the A/C cool down, drive with the windows slightly open for 2-3 minutes after start up or until the vehicle has been “aired out.” • If you are driving during extreme high ambient.
DUAL ZONE AUTOMATIC T EMPERATURE CONTROL WITH HEATED SEATS (IF EQUIPPED) T emperature conversion: T o switch between Fahrenheit and Celsius, refer to Message center in the Instrument Cluster chapter . 1. + Fan speed control: Press to increase the fan speed.
4. A/C: Press to activate/deactivate air conditioning. Use with recirculated air to improve cooling performance and efficiency . A/C engages automatically in MAX A/C, (defrost) and (floor/defrost). 5. AUTO: Press to engage automatic temperature control.
12. – Front fan speed control: Press to decrease the fan speed. 13. A. R Rear defroster (if equipped): Press to activate/deactivate the rear window defroster . Refer to Rear window defroster later in this chapter for more information. If your vehicle is equipped with both rear defroster and heated mirrors, the same button will activate both.
3. Manual override control: Allows you to manually select where airflow is directed. T o return to full automatic control, press AUTO. When choosing to control airflow manually , press repeatedly to t.
9. P ASS TEMP: Press to engage/disengage separate passenger side temperature control. T urn to increase/decrease the air temperature on the passenger side of the vehicle. The recommended initial setting is between 72°F (22°C) and 75°F (24°C), then adjust for comfort.
DUAL ZONE AUTOMATIC T EMPERATURE CONTROL WITH HEATED AND COOLED SEATS (NAVIGATION BASED–IF EQUIPPED) T emperature conversion: T o switch between Fahrenheit and Celsius, refer to Message center in the Instrument Cluster chapter . 1. CLIMA TE: Press to control the climate control system through the touch display screen.
4. Passenger temperature: Press to activate separate passenger temperature control to increase/decrease the air temperature on the passenger side of the vehicle. 5. Passenger heated seat (if equipped): Press to control the passenger heated seat. Refer to Heated and cooled seats in the Seating and Safety Restraints chapter for more information.
of fog and thin ice. The system will automatically provide outside air to reduce window fogging. Press this button again to return to the previous air flow selection. T OUCHSCREEN FUNCTIONS T emperature conversion: T o switch between Fahrenheit and Celsius, refer to Message center in the Instrument Cluster chapter .
V OICE COMMANDS IN CLIMATE MODE Please refer to the V oice commands in climate mode section of the Navigation supplement for more information on using voice commands with the climate control system. Operating tips • T o reduce fog build up on the windshield during humid weather , select (defrost).
T o aid in side window defogging/demisting in cold weather: 1. Select . 2. Select A/C. 3. Adjust the temperature control to maintain comfort. 4. Set the fan speed to the highest setting. 5. Direct the outer instrument panel vents towards the side windows.
HEADLAMP CONTROL Rotate the headlamp control clockwise to the first position to turn on the parking lamps. Rotate clockwise to the second position to also turn on the headlamps. Autolamp control (if equipped) The autolamp system provides light sensitive automatic on-off control of the exterior lights normally controlled by the headlamp control.
At this point, the headlamps and park lamps will turn off. Fog lamp control (if equipped) The headlamp control also operates the fog lamps. The fog lamps can be turned on only when the headlamp control is in the , or position and the high beams are not turned on.
Daytime running lamps (DRL) (if equipped) T urns the headlamps on with a reduced output. In order for the DRLs to function: • the ignition must be in the on position and • the headlamp control is in the , parking lamp or autolamp position. W ARNING: Always remember to turn on your headlamps at dusk or during inclement weather .
V ertical aim adjustment 1. Park the vehicle directly in front of a wall or screen on a level surface, approximately 25 feet (7.6 meters) away . • (1) 8 feet (2.4 meters) • (2) Center height of lamp to ground • (3) 25 feet (7.6 meters) • (4) Horizontal reference line 2.
TURN SIGNAL CONTROL • Push down to activate the left turn signal. • Push up to activate the right turn signal. Push and hold up or down to the first detent to signal a lane change. INTERIOR LAMPS Front row map lamps (if equipped) T o turn on the map lamps, press the outer edge of the clear lens.
Rear dome/courtesy lamps (if equipped) The dome lamp lights when: • any door is opened. • the instrument panel dimmer switch is rotated up until the courtesy lamps come on. • any of the remote entry controls are pressed and the ignition is off. The reading portion, the two outer lights, can only be turned on and off at the lamp.
Ambient lighting (if equipped) Illuminates footwells and cupholders with a choice of several colors. The ambient lighting control is located on the floor console. T o activate, press and release the left side of the control to cycle through the color choices plus the off state.
Using the right bulbs Replacement bulbs are specified in the chart below . Headlamp bulbs must be marked with an authorized “D.O.T .” for North America and an “E” for Europe to ensure lamp performance, light brightness and pattern and safe visibility .
2. Remove the pushpin that holds the air deflector/protective cover from the upper inboard corner of the lamp. 3. Loosen the three retaining bolts (two at top of lamp, one at lower inboard corner). 4. Once the three retaining bolts have been removed, slide the headlamp assembly forward, disconnecting the two snap attachments at the fender .
Install the new bulb in reverse order . Replacing front parking lamp/turn signal/sidemarker bulbs 1. Make sure that the headlamp control is in the off position and open the hood. 2. Remove the pushpin that holds the air deflector/protective cover from the upper inboard corner of the lamp.
3. Carefully pull the lamp assembly straight rearward from the tailgate pillar to disengage two hidden snap-in retainers. (Flare side tail lamps are not equipped with snap-in retainers.) 4. Remove bulb socket from the lamp assembly by turning it counterclockwise.
Replacing exterior mounted mirror turn signal indicator lamp bulbs For bulb replacement, see your authorized dealer . Replacing license plate lamp bulbs The license plate bulbs are located behind the rear bumper . T o change the license plate lamp bulbs: 1.
MULTI-FUNCTION LEVER W indshield wiper: Rotate the end of the control away from you to increase the speed of the wipers; rotate towards you to decrease the speed of the wipers.
W indshield washer: Press the end of the stalk: • briefly: causes a single swipe of the wipers without washer fluid. • a quick press and hold: the wipers will swipe three times with washer fluid. • a long press and hold: the wipers and washer fluid will be activated for up to ten seconds.
POWER TILT STEERING (IF EQUIPPED) The steering column can be adjusted manually by moving the two-way rocker adjustment control located below the turn signal/wiper control stalk. Hold the control to adjust. The tilt function is adjusted by depressing the control up or down.
On vehicles with memory feature, to prevent damage to the steering column, the steering column is designed to set a stopping position just short of the end of the column position. If the steering column encounters an object while moving up or down, a new stopping position will be set.
CENTER CONSOLE (IF EQUIPPED) The center console offers several useful storage features. These include: 1. Cupholders 2. T issue holder in lid 3. Power point 4. Large utility compartment has coin holder slots and a cardholder located inside on the passenger side and a pen holder on the lid.
Compass zone adjustment 1. Determine which magnetic zone you are in for your geographic location by referring to the zone map. 2. T urn ignition to the on position. 3. Press and hold the 7 and 9 radio preset buttons together for approximately five seconds until ZONE XX appears in the CID.
2. T o calibrate, press and hold the 7 and 9 radio preset buttons together for approximately 10 seconds until CAL appears. Release the buttons. 3. Slowly drive the vehicle in a circle (less than 3 mph [5 km/h]) until the CAL display changes to the direction value (N, S, E, W , etc.
• do not leave battery chargers, video game adapters, computers and other devices plugged in overnight or when the vehicle is parked for extended periods. Cupholder/Ashtray (if equipped) The cupholder/ashtray is located on the instrument panel. T o open cupholder/ashtray , push in on the door and release.
Press and pull the window switches to open and close windows. • Press down (to the first detent) and hold the switch to open. • Pull up (to the first detent) and hold the switch to close. Rear W indow Buffeting: When one or both of the rear windows are open, the vehicle may demonstrate a wind throb or buffeting noise.
Power sliding back window (if equipped) Press and hold the the control to open the window all the way to the full open position. Pull and hold the control to close the window . W ARNING: When operating the power sliding back window you must ensure all rear seat occupants and/or cargo are not in the proximity of the back window .
The mirrors will automatically return to the normal state whenever the vehicle is placed in R (Reverse) to ensure a bright clear view when backing up. Do not block the sensors on the front and back of the interior rear view mirror since this may impair proper mirror performance.
Fold-away mirrors Fold the side mirrors in carefully before driving through a narrow space, like an automatic car wash. Powerfold mirrors (if equipped) W ith powerfold mirrors, you can fold the side mirrors using the power mirror switch. 1. Rotate the switch to the center/neutral position.
On vehicles not equipped with rear defrost, press the heated mirror control located on the climate control panel. For more information refer to the Climate Controls chapter . Note: If your vehicle is equipped with the Auto dimming feature, the mirror glass is thicker and will take longer to defrost.
Press and hold the rocker control to adjust accelerator and brake pedal. • Press the right side of the control to adjust the pedals toward you. • Press the left side of the control to adjust the pedals away from you. W ARNING: Never adjust the accelerator and brake pedal with feet on the pedals while the vehicle is moving.
• When this feature is enabled (AUTO), the running boards will move back to the correct positions based off of the door positions. Bounce-back: • If an object is in the way of the moving running board, the running board will automatically bounce back in the reverse direction and move to the end of travel.
Setting speed control The controls for using your speed control are located on the steering wheel for your convenience. 1. Press the ON control and release it. 2. Accelerate to the desired speed. 3. Press the SET + or SET - control and release it. 4. T ake your foot off the accelerator pedal.
Resuming a set speed Press the RESUME control and release it. This will automatically return the vehicle to the previously set speed. Increasing speed while using speed control There are two ways to set a higher speed: • Press and hold the SET + control until you get to the desired speed, then release the control.
Turning of f speed control There are two ways to turn off the speed control: • Depress the brake pedal or the clutch pedal (if equipped). This will not erase your vehicle’ s previously set speed. • Press the speed control OFF control. Note: When you turn off the speed control or the ignition, your speed control set speed memory is erased.
In any mode: • Press VOL + or VOL - to adjust the volume. SYNC 威 system hands free control features (if equipped) Press briefly to use the voice command feature. Y ou will hear a tone and LISTENING will appear in the radio display . Press and hold to exit voice command.
For further information on the Navigation system/SYNC 威 system, refer to the Navigation and SYNC 威 supplements. MOON ROOF (IF EQUIPPED) The moon roof control is located on the overhead console. W ARNING: Do not let children play with the moon roof or leave children unattended in the vehicle.
The moon roof has a built-in sliding shade that can be manually opened or closed when the glass panel is shut. T o close the shade, pull it toward the front of the vehicle. UNIVERSAL GARAGE DOOR OPENER (IF EQUIPPED) The appearance of your vehicle’ s universal garage door opener will vary according to your option package.
Do not use the HomeLink 威 W ireless Control System with any garage door opener that lacks safety stop and reverse features as required by U.S. federal safety standards (this includes any garage door opener model manufactured before April 1, 1982).
• If the indicator light stays on constantly , programming is complete and your device should activate when the HomeLink 威 button is pressed and released.
signal has been accepted by the HomeLink 威 . The indicator light will flash slowly and then rapidly after HomeLink 威 accepts the radio frequency signal. • Proceed with Step 3 in the Programming section. Operating the HomeLink 姞 Wireless Control System T o operate, simply press and release the appropriate HomeLink 威 button.
For questions or comments, contact HomeLink 威 at www .homelink.com or 1–800–355–3515. Car2U 姞 Home Automation System (if equipped) The Car2U 威 Home Automation System is a universal transmi.
T ypes of garage door openers (rolling code and fixed code) The Car2U 威 Home Automation System may be programmed to operate rolling code and fixed code garage door openers. • Rolling code garage door openers were produced after 1996 and are code protected.
2. Go to the garage to locate the garage door opener motor and its “learn” button. Y ou may need a ladder to reach the unit and you may need to remove the unit’ s cover or light lens to locate the “learn” button.
Note: The Car2U 威 system allows for three devices to be programmed. If you need to change or replace any of the three devices after it has been initially programmed, it is necessary to erase the current settings using the Erasing the Car2U 威 Home Automation System buttons procedure and then programming all of the devices being used.
3. T o input these positions into the Car2U 威 system, simultaneously press all three Car2U 威 system buttons for a few seconds and then release to put the device into programming mode.
T o erase programming on the Car2U 威 system (individual buttons cannot be erased), use the following procedure: 1. Firmly press the two outside Car2U 威 system buttons simultaneously for approximately 20 seconds until the indicator lights begin to blink rapidly .
T ailgate removal Y our tailgate is removable to allow more room for loading. W ARNING: Always properly secure cargo to prevent shifting cargo or cargo falling from vehicle, which could result in compromised vehicle stability and serious personal injury to vehicle occupants or others.
T ailgate step (if equipped) Y our vehicle may be equipped with a feature that allows easier entry into the truck bed. T o open the tailgate step: 1. Flip down the tailgate.
Note: • Fully close and latch the tailgate step before moving the vehicle. • Never drive with the step or grab handle deployed. • Replace slip resistance tape (serviceable item) if worn out. • Replace handle molding (serviceable item) if damaged.
T o stow the box side step, with your foot, push the box side step under the truck until fully latched. Do not push on the button while stowing the box side step. Note: Do not use the box side steps to lift the vehicle when jacking. Utilize proper jacking points.
2. Open the latches to release the panels. 3. Rotate the panels toward the tailgate. Repeat Steps 1–3 for the other side of the bed extender . 4. Connect the two panels, then rotate both knobs a quarter -turn clockwise to secure the panels.
5. Ensure the latch rod is inserted into the tailgate hole and the locking pins on both sides are engaged into their holes in the pick-up box. 6. Reverse steps for storage of the bed extender . Note: When the vehicle is in motion, ensure the locking pins and knobs are fully engaged.
CARGO MANAGEMENT SYSTEM (IF EQUIPPED) The cargo management system consists of the Cargo rail package with the following as optional accessories: • Front header bar (if equipped) • Cross bars (if e.
Note: When replacing a cleat into the rail, make sure the oval embossed on the knob is not upside down. This will ensure that the cleat is properly oriented to accept accessory attachments. Front header bar: Spans the header area of the pickup box, providing the function of a header rail.
Cross bars: Aluminum cross bars with T -slot channels in all four sides, and a latch mechanism that allows the end supports to snap over the existing cleats. Cross bars are rated to hold loads up to 100 lb (45 kg) load evenly distributed between the two crossbars, and the T -slots are sized to accept industry-standard roof rack accessories.
Bed divider: This panel will keep small items up to 400 lb (180 kg) in position in the pickup box. Also includes T -slots to allow attachment of industry-standard roof rack accessories. • T o remove bed divider , lift handle on each side and lift end support shroud off of the cleat.
Side mounted tool bins: W atertight bins can be positioned at any point along the side rails and can be easily removed (even when full), and carried to wherever the contents are needed. Each bin will hold up to 60 lb (27 kg) of cargo, and has a drain plug for use as a cooler .
• T o remove the bin from the rail, open lid and pull up on both levers located on the outboard edge (next to the pickup box top rail) until the handles are all the way up (approximately 90 degrees). Once both handles are raised, the lid may be closed.
KEYS The key operates all locks on your vehicle. In case of loss, replacement keys are available from your dealer . Y ou should always carry a second key with you in a safe place in case you require it in an emergency . Refer to the SecuriLock 威 passive anti-theft system section in this chapter for more information.
Autolock The autolock feature is available on vehicles with power locking. This feature will lock all the doors when: • all the doors are closed, • the ignition is in the on position, • you shif.
6. Press the unlock control, then press the lock control. The horn will chirp once if autolock was deactivated or twice (one short and one long chirp) if autolock was activated. 7. T urn the ignition to the off position. The horn will chirp once to confirm the procedure is complete.
Deactivating/activating autounlock feature Y our vehicle comes with the autounlock features activated; there are four methods to enable/disable this feature: • Through your authorized dealer , • b.
4. Press and hold the 3 • 4. While holding the 3 • 4, press and release the 7 • 8. While still holding the 3 • 4, press and release the 7 • 8a second time. 5. Release the 3 • 4. The user should receive a horn chirp to indicate the system has been disabled or a chirp followed by a honk to indicate the system has been enabled.
The typical operating range for your remote entry transmitter is approximately 33 feet (10 meters). A decrease in operating range could be caused by: • weather conditions, • nearby radio towers, • structures around the vehicle, or • other vehicles parked next to your vehicle.
Switching from two step to one step door unlocking Y our vehicle comes with two step unlocking enabled. Unlocking can be switched between two step and one step door unlocking by pressing and holding both the and buttons simultaneously on the remote entry transmitter for approximately four seconds and release.
Activating the memory feature T o activate this feature: 1. Position the seat, power mirrors, adjustable pedals and steering column (if equipped) to the desired positions. 2. Press and hold either the 1 or 2 control on the driver’ s seat for five seconds.
T o replace the battery: 1. T wist a thin coin between the two halves of the remote entry transmitter near the key ring. DO NOT T AKE THE RUBBER COVER AND CIRCUIT BOARD OFF THE FRONT HOUSING OF THE REMOTE ENTRY TRANSMITTER. 2. Do not wipe off any grease on the battery terminals on the back surface of the circuit board.
Programming remote transmitters It is necessary to have all (maximum of four — original and/or new) of your remote transmitters available prior to beginning this procedure. If all remote entry transmitters are not present during the programming procedure, the transmitters that are not present during programming will no longer operate the vehicle.
• after 25 seconds of illumination. The dome lamp control (if equipped) must not be set to the off position for the illuminated entry system to operate. The lights will not turn off if: • they have been turned on with the dimmer control, or • any door is open.
• the control is pressed on the remote entry transmitter . • the ignition is turned from the off position to the on position, or from the on position to the off position. Programming a personal entry code T o create your own personal entry code: 1.
SECURILOCK 姞 PASSIVE ANTI-THEFT SYSTEM SecuriLock 威 passive anti-theft system is an engine immobilization system. This system is designed to help prevent the engine from being started unless a coded key programmed to your vehicle is used. The use of the wrong type of coded key may lead to a “no-start” condition.
Anti-theft indicator The anti-theft indicator is located in the instrument cluster . • When the ignition is in the off position, the indicator will flash once every two seconds to indicate the SecuriLock 威 system is functioning as a theft deterrent.
Programming spare keys A maximum of eight keys can be coded to your vehicle. Only SecuriLock 威 keys can be used. T o program a coded key yourself, you will need two previously programmed coded keys .
If not successful, the new coded key(s) will not start the vehicle’ s engine and the theft indicator will flash on and off and you may repeat Steps 1 through 5. If failure repeats, bring your vehicle to your authorized dealer to have the new spare key(s) programmed.
Create a MyKey™ T o program MyKey™ on one of the keys programmed to the vehicle, insert the key that you want to make a MyKey™ into the ignition. T urn the ignition on. Use the message center buttons to do the following: 1. Press SETUP until PRESS RESET TO CREA TE MYKEY is displayed.
Disable MyKey™ T o reset all MyKeys™ as Admin keys do the following: 1. T urn the vehicle on using the Admin key . 2. Press SETUP until PRESS RESET TO CLEAR MYKEY is displayed. 3. Press and release the RESET button. HOLD RESET TO CONFIRM CLEAR is displayed.
2. Remote start the vehicle using a remote start fob. 3. Follow steps 1-4 in the Create a MyKey™ section. Note: For all vehicles, the number of MYKEY(S) PROGRAMMED or ADMIN KEYS PROGRAMMED that is displayed in the MyKey™ System Status menus will include the remote start system as an additional key in the total count.
T roubleshooting Condition Potential Causes Can’t create a MyKey™ • Key in the ignition is already a MyKey™ • Key in the ignition is the last remaining Admin key (there always has to be at l.
Condition Potential Causes Lost any key • For programming spare keys, refer to the Programming spare keys section in this chapter . I accidentally programmed all keys as MyKeys™ • V ehicle has a remote start system that is recognized as an Admin key .
SEATING W ARNING: Reclining the seatback can cause an occupant to slide under the seat’ s safety belt, resulting in severe personal injuries in the event of a collision. W ARNING: Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop.
T o adjust the head restraint, do the following: 1. Adjust the seatback to an upright driving/riding position. 2. Raise the head restraint by pulling up on the head restraint. 3. Lower the head restraint by pressing and holding the guide sleeve adjust/release button and pushing down on the head restraint.
T o remove the adjustable head restraint, do the following: 1. Pull up the head restraint until it reaches the highest adjustment position. 2. Simultaneously press and hold both the adjust/release button and the unlock/remove button, then pull up on the head restraint.
W ARNING: T o minimize the risk of neck injury in the event of a crash, head restraints must be installed properly . Front seat • Lift the track release bar to move the seat forward or rearward.
• Pull the release lever handle located on the side of the seat up to move the seatback forward or backward. Using the armrest (if equipped) • Push the release control to move the armrest up or down.
• T o gain access to the storage compartment (if equipped) in your armrest, lift the latch to open the lid. Using the manual lumbar support For more lumbar support, turn the lumbar support control toward the front of vehicle. For less lumbar support, turn the lumbar support control toward the rear of vehicle.
Using the power lumbar support (if equipped) The power lumbar control is located on the outboard side of the seat. Press the forward side of the control for additional support.
The control is located on the outboard side of the seat cushion. Move the switch in the direction of the arrows to raise or lower the front portion of the seat cushion. Move the switch in the direction of the arrows to raise or lower the rear portion of the seat cushion.
Memory seat/power mirrors/adjustable pedals/steering column (if equipped) This system allows automatic positioning of the driver seat, outside rearview mirrors, adjustable pedals, and steering column to two programmable positions. The memory seat control is located on the driver’ s seat.
The easy out feature automatically moves the driver’ s seat 2 inches (5 cm) backward when: • the transmission is in P (Park) • the key is removed from the ignition cylinder (If the seat is located less than 2 inches (5 cm) from the rear of the seat track, the seat will travel up to 1 ⁄ 4 inch (.
Heated seats (if equipped) W ARNING: Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury , medication, alcohol use, exhaustion, or other physical conditions, must exercise care when using the seat heater .
Heated seats W ARNING: Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury , medication, alcohol use, exhaustion, or other physical conditions, must exercise care when using the seat heater .
Climate controlled seats air filter replacement (if equipped) The climate controlled seat system includes air filters that must be replaced periodically . Refer to the scheduled maintenance information for more information. • There is a filter located under the rear of each front seat.
T o install a filter: • First, position the filter in it’ s housing making sure that the far forward end is all the way up in the housing. Then push in on the center of the outside edge of the filter and rotate up into the housing until it clips into position.
T o adjust the head restraint, do the following: 1. Raise the head restraint by pulling up on the head restraint. 2. Lower the head restraint by pressing and holding the guide sleeve adjust/release button and pushing down on the head restraint.
T o remove the adjustable head restraint, do the following: 1. Pull up the head restraint until it reaches the highest adjustment position. 2. Simultaneously press and hold both the adjust/release button and the unlock/remove button, then pull up on the head restraint.
W ARNING: T o minimize the risk of neck injury in the event of a crash, head restraints must be installed properly . Folding up the rear seats (SuperCab only) The rear seat has a split 60/40 cushion. Each seat cushion can be flipped up into a vertical storage position.
• Rotate seat cushion up by lifting on the corner until it locks into vertical storage position. Returning the seat to seating position W ARNING: Before returning the seat cushion to its original position, make sure that cargo or any objects are not trapped underneath the seat cushion.
T o close the cupholders: • Push the front edge back into the seat until the cupholders are fully seated. • Make sure there is nothing in the cupholders before attempting to close them. Make sure that the cupholders are fully seated before stowing the armrest.
• Push the indicated side of the control for minimum heat. • Push again to deactivate. The heated seat module resets at every ignition run cycle. While the ignition is in the on position, activating the high or low heated seat switch enables heating mode.
How does the Personal Safety System™ work? The Personal Safety System™ can adapt the deployment strategy of your vehicle’ s safety devices according to crash severity and occupant classification and conditions. A collection of crash and occupant sensors provides information to the Restraints Control Module (RCM).
in rear -facing child seats, this occurs because they are initially sitting very close to the airbag. For other occupants, this occurs when the occupant is not properly restrained by safety belts or child safety seats and they move forward during pre-crash braking.
Front outboard safety belt pretensioners The safety belt pretensioners at the front outboard seating positions are designed to tighten the safety belts firmly against the occupant’ s body during frontal collisions, and in side collisions and rollovers.
Safety restraints precautions W ARNING: Always drive and ride with your seatback upright and the lap belt snug and low across the hips. W ARNING: T o reduce the risk of injury , make sure children sit in a rear seating position where they can be properly restrained.
W ARNING: Safety belts and seats can become hot in a vehicle that has been closed up in sunny weather; they could burn a small child. Check seat covers and buckles before you place a child anywhere near them. W ARNING: Front and rear seat occupants, including pregnant women, should wear safety belts for optimum protection in an accident.
Regular Cab Center front safety belt W ARNING: Always use both lap and shoulder safety belt in the Regular Cab center seating position. If you carry large cargo behind the seat or items that might damage or soil the belt, detach the belt from the seat: • Release the mini-buckle by inserting a key or similar object into the slot.
1. T o lengthen the lap belt, pull some webbing out of the shoulder belt retractor . 2. While holding the webbing below the tongue, grasp the tip (metal portion) of the tongue so that it is parallel to the webbing and slide the tongue upward. 3. Provide enough lap belt length so that the tongue can reach the buckle.
While you are fastened in the safety belt, the combination lap/shoulder belt with a cinch tongue adjusts to your movement. However , if you brake hard, turn hard, or if your vehicle receives an impact of 5 mph (8 km/h) or more, the safety belt will become locked and help reduce your forward movement.
Shorten and fasten the belt when not in use. For long term storage, the lap belt can be placed into a pocket found on the inside lid of the storage compartment. T o store the lap belt, do the following: 1. Open the storage compartment lid. 2. Place the lap belt into the pocket found on the inside lid of the storage compartment.
Energy management retractors Y our vehicle has a safety belt system equipped with energy management retractors at the driver and front outboard passenger seating positions. An energy management retractor is a device which pays out webbing in a controlled manner .
How to use the automatic locking mode 1. Buckle the combination lap and shoulder belt. • Right front passenger seat • Rear seats (if equipped) 2. Grasp the shoulder portion and pull downward until the entire belt is extracted. 3. Allow the belt to retract.
W ARNING: After any vehicle collision, the safety belt systems at all seating positions (except the driver position, which does not have this feature) must be checked by an authorized dealer to verify that the automatic locking retractor feature for child seats is still functioning properly .
Safety belt usage sensors The driver and front outboard passenger safety belt buckles are equipped with sensors that detect if the safety belts are fastened. The sensors provide information to the Personal Safety System 威 which can then adapt the airbag deployment or safety belt pretensioner activation based upon safety belt usage.
Conditions of operation If... Then... The driver’ s safety belt is not buckled before the ignition switch is turned to the on position... The safety belt warning light illuminates 1-2 minutes and the warning chime sounds 4-8 seconds. The driver’ s safety belt is buckled while the indicator light is illuminated and the warning chime is sounding.
The Belt-Minder 威 feature uses two different warning chimes. During the first minute of activation, the warning chime will sound once every second. The remaining warning chimes will sound twice every second while the system is activated. If... Then.
The following are reasons most often given for not wearing safety belts: (All statistics based on U.S. data) Reasons given... Consider ... “Crashes are rare events” 36700 crashes occur every day . The more we drive, the more we are exposed to “rare” events, even for good drivers.
Reasons given... Consider ... “I have an airbag” Airbags offer greater protection when used with safety belts. Frontal airbags are not designed to inflate in rear and side crashes or rollovers. “I’d rather be thrown clear” Not a good idea. People who are ejected are 40 times more likely to DIE.
W ARNING: While the design allows you to deactivate your Belt-Minder 威 , this system is designed to improve your chances of being safely belted and surviving an accident. W e recommend you leave the Belt-Minder 威 system activated for yourself and others who may use the vehicle.
AIRBAG SUPPLEMENT AL RESTRAINT SYSTEM (SRS) The airbag supplemental restraint system is designed to work in conjunction with the safety belts to help protect the driver and front outboard passenger from certain upper body injuries. The term “supplemental restraint” means the airbags are intended as a supplement to the safety belts.
Important SRS precautions The SRS is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries. Airbags DO NOT inflate slowly; t h e r ei sar i s ko fi n j u r yf r o ma deploying airbag.
W ARNING: Do not attempt to service, repair , or modify the airbag supplemental restraint systems or its fuses. Contact your authorized dealer as soon as possible. W ARNING: The front passenger airbag is not designed to offer protection to an occupant in the center front seating position.
If two adults and a child occupy a Regular Cab , properly restrain the child in the center front unless doing so would interfere with driving the vehicle. This arrangement provides lap and shoulder belt protection for all occupants, and airbag protection for the adults.
internal injuries, particularly to occupants who are not properly restrained or are otherwise out of position at the time of airbag deployment. Thus, it is extremely important that occupants be properly restrained as far away from the airbag cover as possible while maintaining vehicle control.
The front passenger sensing system uses a ⬙ passenger airbag off ⬙ or ⬙ pass airbag off ⬙ indicator which will illuminate and stay lit to remind you that the front passenger frontal airbag is disabled. The indicator lamp is located in the center stack of the instrument panel just above the radio.
• If the indicator lamp remains lit even after this, the person should be advised to ride in the rear seat. Occupant Pass Airbag Off Indicator Lamp Passenger Airbag Empty seat Unlit Disabled Small c.
Objects Pass Airbag Off Indicator Lamp Passenger Airbag Small (i.e. three-ring binder , small purse, bottled water) Unlit Disabled Medium (i.e. heavy briefcase, fully packed luggage) Lit Disabled Empt.
A difficulty with the system is indicated by one or more of the following: • The readiness lights will either flash or stay lit. • The readiness lights will not illuminate immediately after ignition is turned on. • A series of five beeps will be heard.
How does the side airbag system work? The design and development of the side airbag system included recommended testing procedures that were developed by a group of automotive safety experts known as the Side Airbag T echnical W orking Group.
W ARNING: Several airbag system components get hot after inflation. Do not touch them after inflation. W ARNING: If the side airbag has deployed, the airbag will not function again. The side airbag system (including the seat) must be inspected and serviced by an authorized dealer .
Safety Canopy 姞 System W ARNING: Do not place objects or mount equipment on or near the headliner at the siderail that may come into contact with a deploying Safety Canopy 威 . Failure to follow these instructions may increase the risk of personal injury in the event of a collision.
How does the Safety Canopy 姞 system work? The design and development of the Safety Canopy 威 system included recommended testing procedures that were developed by a group of automotive safety experts known as the Side Airbag T echnical W orking Group.
The Safety Canopy 威 is mounted to roof side-rail sheet metal, behind the headliner , above each row of seats. The Safety Canopy 威 is designed to inflate between the side window area and occupants to further enhance protection provided in side impact collisions and rollover events.
If any of these things happen, even intermittently , have the SRS serviced at your authorized dealer immediately . Unless serviced, the system may not function properly in the event of a collision.
W ARNING: All children are shaped differently . The Recommendations for Safety Restraints are based on probable child height, age and weight thresholds from NHTSA and other safety organizations or are the minimum requirements of law .
Recommendations for Safety Restraints for Children Child size, height, weight, or age Recommended restraint type Larger children Children who have outgrown or no longer properly fit in a belt-positioning booster seat (generally children who are at least 4 feet 9 inches (1.
Recommendations for attaching child safety restraints for children Restraint T ype Child W eight Use any attachment method as indicated below by “X” LA TCH (lower anchors and top tether anchor) LA.
W ARNING: Always carefully follow the instructions and warnings provided by the manufacturer of any child restraint to determine if the restraint device is appropriate for your child’ s size, height, weight, or age.
training to ensure that all children ages 0 to 16 are properly restrained in the correct restraint system. Ford recommends checking with a NHTSA Certified Child Passenger Safety T echnician (CPST) and your pediatrician to make sure your seat is appropriate for your child and properly installed in the vehicle.
Airbags can kill or injure a child in a child seat. NEVER place a rear -facing child seat in front of an active airbag. If you must use a forward-facing child seat in the front seat, move the vehicle seat all the way back. Children 12 and under should be properly restrained in a rear seating position whenever possible.
If you are using a Regular Cab center seat, see Installing child safety seats in cinch tongue combination lap and shoulder belt seating position later in this chapter for instructions.
3. While holding the shoulder and lap belt portions together , route the tongue through the child seat according to the child seat manufacturer’ s instructions.
8. Remove remaining slack from the belt. Force the seat down with extra weight, e.g., by pressing down or kneeling on the child restraint while pulling up on the shoulder belt in order to force slack from the belt.
W ARNING: Always use both lap and shoulder safety belt in the Regular Cab center seating position. 1. Position the child safety seat in the Regular Cab center front seat.
3. Slide the tongue up the webbing. 4. While holding both shoulder and lap portions next to the tongue, route the tongue and webbing through the child seat according to the child seat manufacturer’ s instructions. Be sure that the belt webbing is not twisted.
6. While pushing down with your knee on the child seat pull up on the shoulder belt portion to tighten the lap belt portion of the combination lap and shoulder belt. 7. Allow the safety belt to retract and remove any slack in the belt to securely tighten the child safety seat in the vehicle.
W ARNING: Never place a rear -facing child seat in the front center seating position of a vehicle with rear seating positions. 1. Lengthen the lap belt. T o lengthen the belt, hold the tongue so that its bottom is perpendicular to the direction of webbing while sliding the tongue up the webbing.
Y our vehicle is equipped with LA TCH lower anchors for child seat installation at the following seating positions (LA TCH is not available on F150 Regular cab) : • F150 SuperCab and SuperCrew The LA TCH anchors are located at the rear section of the rear seat between the cushion and seatback.
Use of inboard lower anchors from the outboard seating positions (center seating use) The lower anchors at the center of the second row rear seat are spaced 652 mm (25.7 inches) apart. The standardized spacing for LA TCH lower anchors is 280 mm (11 inches) center to center .
point called the top tether anchor . T ether straps are available as an accessory for many older safety seats. Contact the manufacturer of your child seat for information about ordering a tether strap, or to obtain a longer tether strap if the tether strap on your safety seat does not reach the appropriate top tether anchor in the vehicle.
Front seat tether strap attachment 1. Route the child safety seat tether strap over the back of the seat and under the head restraint. For vehicles with adjustable head restraints, route the tether strap under the head restraint and between the head restraint posts, otherwise route the tether strap over the top of the seatback.
Rear seat tether strap attachment There are three loops of webbing just above the back of the rear seat (along the bottom edge of the rear window) in the SuperCab and SuperCrew . These loops are to be used as both routing loops and anchor loops for up to three child safety seat tether straps.
3. T ighten the tether strap according to the child seat manufacturer’ s instructions. If the safety seat is not anchored properly , the risk of a child being injured in a collision greatly increases.
When children should use booster seats Children need to use booster seats from the time they outgrow the toddler seat until they are big enough for the vehicle seat and lap/shoulder belt to fit properly . Generally this is when they reach a height of at least 4 feet 9 inches (1.
• High back booster seats If, with a backless booster seat, you cannot find a seating position that adequately supports your child’ s head, a high back booster seat would be a better choice.
If the booster seat slides on the vehicle seat, placing a rubberized mesh sold as shelf or carpet liner under the booster seat may improve this condition. Do not introduce any item thicker than this under the booster seat. Check with the booster seat manufacturer’ s instructions.
W ARNING: Failure to inspect and if necessary replace the safety belt assembly or child restraint system under the above conditions could result in severe personal injuries in the event of a collision.
NOTICE TO UTILITY VEHICLE AND TRUCK OWNERS Utility vehicles and trucks handle differently than passenger cars in the various driving conditions that are encountered on streets, highways and off-road.
Power is supplied to all four wheels through a transfer case or power transfer unit. 4WD vehicles allow you to select different drive modes as necessary . Information on transfer case operation and shifting procedures can be found in the Driving chapter .
• Narrower — to provide greater maneuverability in tight spaces, particularly in off-road use. As a result of the above dimensional differences, SUV’ s and trucks often will have a higher center of gravity and a greater difference in center of gravity between the loaded and unloaded condition.
T readwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half (1 1 ⁄ 2 ) times as well on the government course as a tire graded 100.
TIRES T ires are designed to give many thousands of miles of service, but they must be maintained in order to get the maximum benefit from them. Glossary of tire terminology • T ire label: A label showing the OE (Original Equipment) tire sizes, recommended inflation pressure and the maximum weight the vehicle can carry .
INFLATING Y OUR TIRES Safe operation of your vehicle requires that your tires are properly inflated. Remember that a tire can lose up to half of its air pressure without appearing flat. Every day before you drive, check your tires. If one looks lower than the others, use a tire gauge to check pressure of all tires and adjust if required.
The cold inflation pressure should never be set lower than the recommended pressure on the Safety Compliance Certification Label or T ire Label. When weather temperature changes occur , tire inflation pressures also change. A 10°F (6°C) temperature drop can cause a corresponding drop of 1 psi (7 kPa) in inflation pressure.
TIRE CARE Inspecting your tires and wheel valve stems Periodically inspect the tire treads for uneven or excessive wear and remove objects such as stones, nails or glass that may be wedged in the tread grooves.
W ARNING: Age T ires degrade over time depending on many factors such as weather , storage conditions, and conditions of use (load, speed, inflation pressure, etc.) the tires experience throughout their lives. In general, tires should be replaced after six years regardless of tread wear .
W ARNING: Only use replacement tires and wheels that are the same size, load index, speed rating and type (such as P-metric versus L T -metric or all-season versus all-terrain) as those originally provided by Ford.
It is recommended that the two front tires or two rear tires generally be replaced as a pair . The tire pressure sensors mounted in the wheels (originally installed on your vehicle) are not designed to be used in aftermarket wheels.
Tire and wheel alignment A bad jolt from hitting a curb or pothole can cause the front end of your vehicle to become misaligned or cause damage to your tires. If your vehicle seems to pull to one side when you’re driving, the wheels may be out of alignment.
Note: If your tires show uneven wear ask an authorized dealer to check for and correct any wheel misalignment, tire imbalance or mechanical problem involved before tire rotation.
Information on “P” type tires P215/65R15 95H is an example of a tire size, load index and speed rating. The definitions of these items are listed below . (Note that the tire size, load index and speed rating for your vehicle may be different from this example.
Note: Y ou may not find this information on all tires because it is not required by federal law . Letter rating Speed rating - mph (km/h) M 81 mph (130 km/h) N 87 mph (140 km/h) Q 99 mph (159 km/h) R .
12. T readwear , T raction and T emperature Grades • T readwear: The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course.
Additional information contained on the tire sidewall for “L T” type tires “L T” type tires have some additional information beyond those of “P” type tires; these differences are described below . Note: T ire Quality Grades do not apply to this type of tire.
Information on “T” type tires “T” type tires have some additional information beyond those of “P” type tires; these differences are described below: T145/80D16 is an example of a tire size. Note: The temporary tire size for your vehicle may be different from this example.
TIRE PRESSURE MONITORING SYSTEM (TPMS) (IF EQUIPPED) Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label.
The T ire Pressure Monitoring System complies with part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Understanding your Tire Pressure Monitoring System (TPMS) The T ire Pressure Monitoring System measures pressure in your four road tires and sends the tire pressure readings to your vehicle. The Low T ire W arning Lamp will turn ON if the tire pressure is significantly low .
When you believe your system is not operating properly The main function of the T ire Pressure Monitoring System is to warn you when your tires need air .
Low T ire Pressure W arning Light Possible cause Customer Action Required Flashing W arning Light Spare tire in use Y our temporary spare tire is in use.
TPMS reset procedure The TPMS reset procedure needs to be performed after each tire rotation on vehicles that require different recommended tire pressures in the front tires as compared to the rear tires.
3. Cycle the ignition to the on position with the engine off. 4. T urn the hazard flashers on then off 3 times. This must be accomplished within ten seconds. If the reset mode has been entered successfully , the horn will sound once, the TPMS indicator will flash and the message center (if equipped) will display TRAIN LEFT FRONT TIRE .
8. Remove the valve cap from the valve stem on the right rear tire. Decrease the air pressure until the horn sounds. 9. Remove the valve cap from the valve stem on the left rear tire.
Follow these guidelines when using snow tires and chains: • Use only SAE Class S chains. • Install chains securely , verifying that the chains do not touch any wiring, brake lines or fuel lines. • Drive cautiously . If you hear the chains rub or bang against your vehicle, stop and re-tighten the chains.
Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be found on the T ire Label on the B-Pillar or the edge of the driver’ s door (vehicles exported outside the US and Canada may not have a T ire Label).
Example only: Cargo W eight – includes all weight added to the Base Curb W eight, including cargo and optional equipment. When towing, trailer tongue load or king pin weight is also part of cargo weight. GA W (Gross Axle W eight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload.
GA WR (Gross Axle W eight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Label located on the B-Pillar or the edge of the driver’ s door .
• Example only: W ARNING: Exceeding the Safety Compliance Certification Label vehicle weight rating limits could result in substandard vehicle handling or performance, engine, transmission and/or structural damage, serious damage to the vehicle, loss of control and personal injury .
GCW (Gross Combined W eight) – is the weight of the loaded vehicle (GVW) plus the weight of the fully loaded trailer . GCWR (Gross Combined W eight Rating) – is the maximum allowable weight of the vehicle and the loaded trailer – including all cargo and passengers – that the vehicle can handle without risking damage.
W ARNING: Exceeding any vehicle weight rating limitation could result in serious damage to the vehicle and/or personal injury . Steps for determining the correct load limit: 1. Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lb.
to transport the cement to your home? If you and your friend each weigh 220 lb. (99 kg), the calculation would be: 1400 - (2 x 220) - (12 x 100) = 1400 - 440 - 1200 = - 240 lb.
Y our vehicle’ s load capacity is designated by weight, not by volume, so you cannot necessarily use all available space when loading a vehicle. T owing a trailer places an additional load on your vehicle’ s engine, transmission, axle, brakes, tires and suspension.
Regular Cab 4x2 (145” wheelbase) Engine Rear axle ratio Maximum GCWR-lb. (kg) Maximum trailer weight-lb. (kg) 4.6L 2V 3.55 10600 (4808) 5500 (2495) 3.73 11100 (5035) 6000 (2722) 4.6L 3V 3.31 13100 (5942) 8000 (3629) 3.55 13600 (6169) 8400 (3810) 5.4L 3.
SuperCab 4x2 (145” wheelbase) Engine Rear axle ratio Maximum GCWR-lb. (kg) Maximum trailer weight-lb. (kg) 5.4L 3.15 14000 (6350) 8600 (3900) 3.55 15200 (6895) 9800 (4445) 3.73 16900 (7666) 11300 (5126) SuperCab 4x4 (145” wheelbase) Engine Rear axle ratio Maximum GCWR-lb.
SuperCrew 4x2 (145” wheelbase) Engine Rear axle ratio Maximum GCWR-lb. (kg) Maximum trailer weight-lb. (kg) 4.6L 2V 3.55 10600 (4808) 5200 (2359) 3.73 11100 (5035) 5700 (2585) 4.6L 3V 3.15 13000 (5897) 7500 (3402) 3.31 13500 (6123) 8100 (3674) 3.55 14900 (6759) 9400 (4264) 5.
SuperCrew 4x4 (145” wheelbase) Harley-Davidson V ersion Engine Rear axle ratio Maximum GCWR-lb. (kg) Maximum trailer weight-lb. (kg) 5.4L 3.73 11200 (5080) 5100 (2313) SuperCrew4x2 (157” wheelbase) Engine Rear axle ratio Maximum GCWR-lb. (kg) Maximum trailer weight-lb.
Note: Do not exceed trailer weight of 5,000 lb. (2,268 kg) when towing with bumper only . Preparing to tow Use the proper equipment for towing a trailer and make sure it is properly attached to your vehicle. Contact your authorized dealer or a reliable trailer dealer as soon as possible if you require assistance.
T railer brakes Electric brakes and manual, automatic or surge-type trailer brakes are safe if installed properly and adjusted to the manufacturer’ s specifications. The trailer brakes must meet local and Federal regulations. W ARNING: Do not connect a trailer’ s hydraulic brake system directly to your vehicle’ s brake system.
The trailer brake controller (TBC) is designed to display three items of information in the instrument cluster message center . These are: gain setting, output bar graph, and trailer connectivity status. They will appear as follows in the message center .
The GAIN should be set to provide the maximum trailer braking assistance while ensuring the trailer wheels do not lock when braking. Locked trailer wheels may lead to trailer instability . Note: This should only be performed in a traffic free environment at speeds of approximately 20–25 mph (30–40 km/h).
Note: Y our TBC can be diagnosed by your authorized dealer to determine exactly which trailer fault has occurred; however , if the fault is with the trailer this diagnosis is not covered under your Ford warranty . Points to Remember: • Remember to adjust gain setting before using the TBC for the first time.
T railer lamps T railer lamps are required on most towed vehicles. Make sure all running lights, brake lights, turn signals and hazard lights are working. Contact your authorized dealer or trailer rental agency for proper instructions and equipment for hooking up trailer lamps.
T railer towing tips • Practice turning, stopping and backing up before starting on a trip to get the feel of the vehicle trailer combination. When turning, make wider turns so the trailer wheels will clear curbs and other obstacles. • Allow more distance for stopping with a trailer attached.
Exceeding these limits may allow water to enter vehicle components: • causing internal damage to the components. • affecting driveability , emissions and reliability . Replace the rear axle lubricant any time the axle has been submerged in water .
In case of a roadside emergency with a disabled vehicle, see Wrecker towing in the Roadside Emergencies chapter . 4WD vehicles equipped with an electronic-shift transfer case: Do not tow your vehicle with any wheels on the ground, as vehicle or transmission damage may occur .
STARTING Positions of the ignition 1. Off — locks the automatic transmission gearshift lever and allows key removal. Note: The ignition key cannot be removed from the ignition unless the gearshift lever is securely latched in P (Park). 2. Accessory — allows the electrical accessories such as the radio to operate while the engine is not running.
W ARNING: Do not start your vehicle in a closed garage or in other enclosed areas. Exhaust fumes can be toxic. Always open the garage door before you start the engine.
• 6–speed transmission 4. Make sure the parking brake is set. 5. T urn the key to 3 (on) without turning the key to 4 (start). Some warning lights will briefly illuminate. See W arning lights and chimes in the Instrument Cluster chapter for more information regarding the warning lights.
Starting the engine 1. T urn the key to 3 (on) without turning the key to 4 (start). 2. T urn the key to 4 (start), then release the key as soon as the engine begins cranking. Y our vehicle has a computer assisted cranking system that assists in starting the engine.
If you should experience cold weather starting problems on E 85 ethanol, and neither an alternative brand of E 85 ethanol nor an engine block heater is available, the addition of unleaded gasoline to your tank will improve cold starting performance.
W ARNING: Failure to follow engine block heater instructions could result in property damage or physical injury . W ARNING: T o reduce the risk of electrical shock, do not use your heater with ungrounded electrical systems or two-pronged (cheater) adapters.
• Finally , have the engine block heater system checked during your fall tune-up to be sure it’ s in good working order . How to use the engine block heater Ensure the receptacle terminals are clean and dry prior to use. T o clean them, use a dry cloth.
Using ABS When hard braking is required, apply continuous force on the brake pedal; do not pump the brake pedal since this will reduce the effectiveness of the ABS and will increase your vehicle’ s stopping distance. The ABS will be activated immediately , allowing you to retain steering control during hard braking and on slippery surfaces.
W ARNING: Always set the parking brake fully and make sure that the gearshift is securely latched in P (Park) (automatic transmission) or in 1 (First) (manual transmission).
W ARNING: If a failure has been detected within the AdvanceT rac 威 with RSC 威 system, the “sliding car” icon will illuminate steadily . V erify that the AdvanceT rac 威 with RSC 威 system is not manually disabled (push the AdvanceT rac 威 with RSC 威 control button located on the center of the instrument panel).
When AdvanceT rac 威 with RSC 威 performs a normal system self-check, some drivers may notice a slight movement of the brake, and/or a rumble, grunting, or grinding noise after startup and when driving off.
Electronic stability control (ESC) Electronic stability control (ESC) may enhance your vehicle’ s directional stability during adverse maneuvers, for example when cornering severely or avoiding objects in the roadway .
The Roll Stability Control™ system may be deactivated in certain situations. See the Switching off AdvanceT rac 威 with RSC 威 section following. Switching off AdvanceT rac 威 with RSC 威 If the.
AdvanceT rac 威 with RSC 威 Features Button functions “Sliding car” icon RSC 威 ESC TCS V ehicle speed exceeds 35 mph (56 km/h) after button is pressed and held for more than five seconds Illum.
Disabling trailer sway control T railer sway control can be disabled during any key cycle. See trailer sway control under the Message center in the Instrument Cluster chapter . Note that regardless of chosen enable state, trailer sway control will be re-enabled at each new key cycle.
LIMITED-SLIP AXLE (IF EQUIPPED) This axle provides added traction on slippery surfaces, particularly when one wheel is on a poor traction surface. Under normal conditions, the Limited-slip axle functions like a standard rear axle. The axle may exhibit a slight noise or vibration in tight turns with low vehicle speed.
W ARNING: Loaded vehicles, with a higher center of gravity , may handle differently than unloaded vehicles. Do not overload your vehicle and use extra precautions, such as driving at slower speeds, avoiding abrupt steering changes and allowing for increased stopping distance, when driving a heavily loaded vehicle.
3. T urn the steering wheel one-half turn to access the slots on each side of the steering wheel. 4. Insert a flat head screwdriver into each slot to unsnap and remove the steering column cover . Rotate the column up on its hinges and pull rearward to remove the cover from the hinges.
6. Reinstall the steering column cover , start the vehicle and release the parking brake. Note: After the transmission is shifted to N (Neutral), it is easier to reinstall the cover when the column is in the middle or lower tilt position. W ARNING: Do not drive your vehicle until you verify that the brakelamps are working.
If the fuse is not blown and the brakelamps are working properly , the following procedure will allow you to move the gearshift lever from P (Park): 1.
AUTOMATIC TRANSMISSION OPERATION Understanding the gearshift positions of the 4–speed automatic transmission Y our vehicle has been designed to improve fuel economy by reducing fuel usage during coasting or deceleration.
W ARNING: Always set the parking brake fully and make sure the gearshift is latched in P (Park). T urn the ignition to the off position and remove the key whenever you leave your vehicle. R (Reverse) W ith the gearshift lever in R (Reverse), the vehicle will move backward.
• O/D (Overdrive) is automatically returned each time the key is turned off. 2 (Second) This position allows for second gear only . • Provides engine braking. • Use to start-up on slippery roads. • T o return to D (Overdrive), move the gearshift lever into the D (Overdrive) position.
P (Park) This position locks the transmission and prevents the rear wheels from turning. T o put your vehicle in gear: • Press the brake pedal • Start the engine • Move the gearshift lever into the desired gear .
• Column-shift transmission • Floor -shift transmission The TOW HAUL indicator light will illuminate in the instrument cluster . T ow/Haul delays upshifts to reduce frequency of transmission shifting.
W ARNING: Do not use the T ow/Haul feature when driving in icy or slippery conditions as the increased engine braking can cause the rear wheels to slide and the vehicle to swing around with the possible loss of vehicle control. 3 (Third) T ransmission operates in third gear only .
REVERSE SENSING SYSTEM (IF EQUIPPED) The Reverse Sensing System (RSS) sounds a tone to warn the driver of obstacles near the rear bumper when R (Reverse) is selected and the vehicle is moving at speeds less than 3 mph (5 km/h). The system is not effective at speeds above 3 mph (5 km/h) and may not detect certain angular or moving objects.
The RSS detects obstacles up to 6 feet (2 meters) from the rear bumper with a decreased coverage area at the outer corners of the bumper , (refer to the figures for approximate zone coverage areas). As you move closer to the obstacle, the rate of the tone increases.
REARVIEW CAMERA SYSTEM (IF EQUIPPED) The rearview camera system, located on the tailgate, provides a video image, which appears in the rearview mirror or the navigation system (if equipped), of the area behind the vehicle. It adds assistance to the driver while reversing or reverse parking the vehicle.
Note: The default setting for the rear camera delay is off. Press the “Settings” button found on the navigation screen (if equipped) to set the rear camera delay feature to on or off.
Servicing • If the image comes on while the vehicle is not in R (Reverse), have the system inspected by your authorized dealer . • If the image is not clear , then check if there is anything covering the lens such as dirt, mud, ice, snow , etc.
• 4X4 LOW - Illuminates when 4L is selected. • - Illuminates when the electronic locking differential (ELD) is selected (if equipped). • CHECK 4X4 - Displays when a 4X4 fault is present. Note: When a 4X4 system fault is present, the system will typically remain in whichever 4X4 mode was selected prior to the fault condition occurring.
Note: Momentarily releasing the accelerator pedal while preforming a shift will improve engagement/disengagement times. Note: Do not perform this operation if the rear wheels are slipping. Note: Some noise may be heard as the system shifts or engages; this is normal.
Using the electronic shift 4WD system (if equipped) 2H (4X2) - Power to the rear wheels only; used for street and highway driving. Provides optimal smoothness and fuel economy at high speeds. 4H (4X4 High) - Used for extra traction such as in snow or icy roads or in off-road situations.
If SHIFT DELA YED PULL FOR W ARD is displayed in the message center , transfer case gear tooth blockage is present. T o alleviate this condition, place the transmission in a forward gear , move the vehicle forward approximately 5 feet (2 meters), and shift the transmission back to neutral to allow the transfer case to complete the range shift.
Shifting between A WD (Auto) and 4H (High) Move the control from A WD to 4H at a stop or while driving at any speed. The message center will display “A WD” if A WD has been selected and “4X4 Hig.
Activating the electronic locking differential (ELD) The ELD can be turned on by pulling the knob on the 4WD control toward you while the control is in either 4H (4X4 High) or 4L (4X4 Low) mode. Once the knob is pulled, the light located on the control will blink for approximately two seconds and then it will remain solid.
Maintain steering wheel control at all times, especially in rough terrain. Since sudden changes in terrain can result in abrupt steering wheel motion, make sure you grip the steering wheel from the outside. Do not grip the spokes. Drive cautiously to avoid vehicle damage from concealed objects such as rocks and stumps.
W ARNING: V ehicles with a higher center of gravity such as utility and four -wheel drive vehicles handle differently than vehicles with a lower center of gravity .
W ARNING: V ehicles with a higher center of gravity such as utility and four -wheel drive vehicles handle differently than vehicles with a lower center of gravity .
found in the Maintenance and Specifications chapter . Y ou should become thoroughly familiar with this information before you operate your vehicle. Normal characteristics On some 4WD models, the initial shift from two-wheel drive to 4x4 while the vehicle is moving can cause some momentary clunk and ratcheting sounds.
Driving through deep water may damage the transmission. If the front or rear axle is submerged in water , the axle lubricant should be replaced. After driving through mud, clean off residue stuck to rotating driveshafts and tires. Excess mud stuck on tires and rotating driveshafts causes an imbalance that could damage drive components.
Descend a hill in the same gear you would use to climb up the hill to avoid excessive brake application and brake overheating. Do not descend in neutral; instead, disengage overdrive or manually shift to a lower gear . When descending a steep hill, avoid sudden hard braking as you could lose control.
W ARNING: If you are driving in slippery conditions that require tire chains or cables, then it is critical that you drive cautiously . Keep speeds down, allow for longer stopping distances and avoid aggressive steering to reduce the chances of a loss of vehicle control which can lead to serious injury or death.
Once through the water , always dry the brakes by moving your vehicle slowly while applying light pressure on the brake pedal. W et brakes do not stop the vehicle as quickly as dry brakes. SNOWPLOWING For F-150 snowplow applications, Ford recommends the F-150 4x4 Regular Cab and SuperCab equipped with the 5.
• Front wheel toe may require re-adjustment to prevent premature uneven tire wear . Specifications are found in the Ford W orkshop Manual. • Headlight aim may require re-adjustment. • The tire air pressures recommended for general driving are found on the vehicle’ s Safety Certification Label.
W ARNING: Do not attempt to service, repair , or modify the air bag supplemental restraint system (SRS) or its fuses. See your Ford or Lincoln Mercury dealer . Transmission operation while plowing • Shift transfer case to 4L (4WD Low) when plowing in small areas at speeds below 5 mph (8 km/h).
Factory installed snow plow prep package vehicles already have been programmed with the unique power train control strategy to provide proper cooling. If the vehicle is being upgraded to the equivalen.
ROADSIDE ASSISTANCE Getting roadside assistance T o fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program.
Canadian customers refer to your Customer Information Guide for information on: • coverage period • exact fuel amounts • towing of your disabled vehicle • emergency travel expense reimbursemen.
Note: W ith extended use, the flasher may run down your battery . FUEL PUMP SHUT-OFF In the event of a moderate to severe collision, this vehicle is equipped with a fuel pump shut-off feature that stops the flow of fuel to the engine. Not every impact will cause a shut-off.
Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 2A Grey Grey — — — 3A Violet Violet — — — 4A Pink Pink — — — 5A T an T an — — — 7.
T o reinstall the fuse box cover , place the top part of the cover on the fuse panel, then push the bottom part of the cover until you hear it click shut.
Fuse/Relay Location Fuse Amp Rating Protected Circuits 9 15A Interior courtesy lights, Cargo lamps 10 15A Backlighting, Puddle lamps 11 10A GPS module 12 7.
Fuse/Relay Location Fuse Amp Rating Protected Circuits 33 10A T railer brake controller 34 5A Electronic locking differential indicator 35 10A Rear park assist 36 5A Passive anti-theft system transcei.
W ARNING: T o reduce risk of electrical shock, always replace the cover to the Power Distribution Box before reconnecting the battery or refilling fluid reservoirs. If the battery has been disconnected and reconnected, refer to the Battery section of the Maintenance and Specifications chapter .
Fuse/Relay Location Fuse Amp Rating Protected Circuits 11 30A** Power running board motors 12 40A** Electric fan 13 30A** Starter relay 14 30A** Passenger power seats 15 40A** Electric fan 16 — Not .
Fuse/Relay Location Fuse Amp Rating Protected Circuits 39 — Back up lamps relay 40 — Electric fan relay 41 15A* Heated mirror 42 — Not used 43 20A* Backup lamp relay 44 15A* Upfitter 3 45 20A* T.
Fuse/Relay Location Fuse Amp Rating Protected Circuits 67 — Not used 68 20A** 4x4 module 69 30A** Passenger heated/cooled seats 70 — Not used 71 — Not used 72 20A** Auxiliary power point (Rear) .
CHANGING THE TIRES If you get a flat tire while driving, do not apply the brake heavily . Instead, gradually decrease your speed. Hold the steering wheel firmly and slowly move to a safe place on the side of the road. Note: The tire pressure monitoring system (TPMS) indicator light will illuminate when the spare tire is in use.
2. Full-size dissimilar spare with label on wheel: This spare tire has a label on the wheel that states: “THIS TIRE AND WHEEL FOR TEMPORARY USE ONL Y” When driving with one of the dissimilar spare.
• W et weather driving capability • All-Wheel driving capability (if applicable) • Load leveling adjustment (if applicable) When driving with the full-size dissimilar spare tire/wheel additional.
T o remove the jack on SuperCrew models: 1. Lift both rear seat cushions. 2. Remove the insert containing the Easy Fuel ™ funnel from the driver’ s side. 3. Remove the two small wing nuts on the passenger side. 4. Slide the plastic box toward the driver’ s side and remove.
W ARNING: Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. Note: Passengers should not remain in the vehicle when the vehicle is being jacked.
• Front Note: Use the frame rail as the jacking location point, NOT the control arm. Note: For F-150 SVT Raptor , you must always use the jack saddle extension.
6. Remove the lug nuts with the lug wrench. 7. Replace the flat tire with the spare tire, making sure the valve stem is facing outward. Reinstall the lug nuts until the wheel is snug against the hub. Do not fully tighten the lug nuts until the wheel has been lowered.
3. T urn the jack handle clockwise until the tire is raised to its stowed position underneath the vehicle. The effort to turn the jack handle increases significantly and the spare tire carrier ratchets or slips when the tire is raised to the maximum tightness.
Note: Inspect the wheel pilot hole prior to installation. If there is visible corrosion in wheel pilot hole, remove loose particles by wiping with clean rag and apply grease. Apply grease only to the wheel pilot hole surface by smearing a “dime” (1 square cm) sized glob of grease around the wheel pilot surface (1) with end of finger .
Preparing your vehicle When the battery is disconnected or a new battery is installed, the automatic transmission must relearn its shift strategy . As a result, the transmission may have firm and/or soft shifts. This operation is considered normal and will not affect function or durability of the transmission.
2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery . 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery .
4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’ s engine, away from the battery and the carburetor/fuel injection system. Note: Do not attach the negative (-) cable to fuel lines, engine rocker covers, the intake manifold or electrical components as grounding points.
Removing the jumper cables Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the ground metal surface. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery .
3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’ s battery . 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’ s battery .
WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or , if you are a member of a roadside assistance program, your roadside assistance service provider . Ford recommends your vehicle be towed with a wheel lift or flatbed.
Emergency towing In case of a roadside emergency with a disabled vehicle (without access to wheel dollies, car hauling trailer , or flatbed transport vehicle) your vehicle (regardless of transmission .
GETTING THE SERVICES YOU NEED W arranty repairs to your vehicle must be performed by an authorized Ford, Lincoln, or Mercury dealer . While any authorized dealer handling your vehicle line will provide warranty service, we recommend you return to your selling authorized dealer who wants to ensure your continued satisfaction.
In Canada: Mailing address (Ford vehicles) Customer Relationship Centre Ford Motor Company of Canada, Limited P .O. Box 2000 Oakville, Ontario L6J 5E4 T elephone 1-800-565-3673 (FORD) Online www .ford.ca Mailing address (Lincoln vehicles) Lincoln Centre Ford Motor Company of Canada, Limited P .
In the United States, a warranty dispute must be submitted to the BBB AUTO LINE before taking action under the Magnuson-Moss W arranty Act, or to the extent allowed by state law , before pursuing replacement or repurchase remedies provided by certain state laws.
THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM (U.S. ONLY) Y our satisfaction is important to Ford Motor Company and to your dealer . If a warranty concern has not been resolved using the three-step procedure outlined on the first page of the Customer Assistance section, you may be eligible to participate in the BBB AUTO LINE program.
UTILIZING THE MEDIATION/ARBITRATION PROGRAM (CANADA ONLY) For vehicles delivered to authorized Canadian dealers. In those cases where you continue to feel that the efforts by Ford of Canada and the au.
If your vehicle must be serviced while you are traveling or living in Central America, the Caribbean, or the Middle East, contact the nearest authorized dealer . If the authorized dealer cannot help you, contact: FORD MOTOR COMP ANY FORD EXPORT OPERA TIONS 1555 Fairlane Drive Fairlane Business Park #3 Allen Park, Michigan 48101 U.
REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway T raffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company .
W ASHING THE EXTERIOR W ash your vehicle regularly with cool or lukewarm water and a neutral pH shampoo, such as Motorcraft 威 Detail W ash (ZC-3-A), which is available from your authorized dealer . • Never use strong household detergents or soap, such as dish washing or laundry liquid.
• After polishing chrome bumpers, apply a coating of Motorcraft 威 Premium Liquid W ax (ZC-53-A), available from your authorized dealer , or an equivalent quality product to help protect from environmental effects. W AXING • W ash the vehicle first.
ENGINE Engines are more efficient when they are clean because grease and dirt buildup keep the engine warmer than normal. When washing: • T ake care when using a power washer to clean the engine. The high-pressure fluid could penetrate the sealed parts and cause damage.
5.4L ENGINE PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products are available from your authorized dealer . • For routine cleaning, use Motorcraft 威 Detail W ash (ZC-3-A). • If tar or grease spots are present, use Motorcraft 威 Bug and T ar Remover (ZC-42).
• The wiper blades can be cleaned with isopropyl (rubbing) alcohol or Motorcraft 威 Premium W indshield W asher Concentrate (ZC-32-A), available from your authorized dealer .
For removal of fine scuffs and scratches, use Scotch-Brite 威 Microfiber Cloth or cheese cloth along with Motorcraft Premium Liquid W ax (ZC-53-A), Motorcraft Paint Sealant (ZC-45), or Motorcraft Custom Clear Coat Polish (ZC-8-A).
be completely cleaned by this method, the area may be cleaned using a commercially available cleaning product designed for automotive interiors. 3. If necessary , apply more soap and water solution or cleaning product to a clean, white, cotton cloth and press the cloth onto the soiled area–allow this to set at room temperature for 30 minutes.
• If the leather cannot be completely cleaned using a mild soap and water solution, the leather may be cleaned using a commercially available cleaning product designed for automotive interiors.
Scratches Natural Markings - Because the leather in the seat comes from genuine steer hides, there will be evidence of naturally occurring markings, such as small scars. These markings give character to the seating covers and should be considered as proof of a genuine leather product.
FORD AND LINCOLN MERCURY CAR CARE PRODUCTS Y our Ford or Lincoln Mercury authorized dealer has many quality products available to clean your vehicle and protect its finishes. These quality products have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and appearance of your vehicle.
SERVICE RECOMMENDATIONS T o help you service your vehicle, we provide scheduled maintenance information which makes tracking routine service easy . If your vehicle requires professional service, your authorized dealer can provide the necessary parts and service.
OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the bottom of the instrument panel. 2. Go to the front of the vehicle and release the auxiliary latch that is located on the front bumper under the grill. 3. Lift the hood until the lift cylinders hold it open.
IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 4.6L V8 1. W indshield washer fluid reservoir 2. T ransmission fluid dipstick (4.6L 2V only) 3. Brake fluid reservoir 4. Engine coolant reservoir 5. Air filter assembly 6. Power steering fluid reservoir 7.
5.4L V8 1. W indshield washer fluid reservoir 2. Engine oil dipstick 3. Brake fluid reservoir 4. Engine coolant reservoir 5. Air filter assembly 6. Power steering fluid reservoir 7.
WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if the level is low . In very cold weather , do not fill the reservoir completely . Only use a washer fluid that meets Ford specification WSB-M8B16-A2. Do not use any special washer fluid such as windshield water repellent type fluid or bug wash.
CHANGING THE WIPER BLADES 1. Pull the wiper arm away from the vehicle. T urn the blade at an angle from the wiper arm. Press the lock tab to release the blade and pull the wiper blade down toward the windshield to remove it from the arm. 2. Attach the new wiper to the wiper arm and press it into place until a click is heard.
5. Locate and carefully remove the engine oil level dipstick. 6. W ipe the dipstick clean. Insert the dipstick fully , then remove it again. • If the oil level is between the lower and upper holes or between the MIN and MAX marks (depending on application), the oil level is acceptable.
Engine oil and filter recommendations Look for this certification trademark. Use SAE 5W -20 engine oil Only use oils “Certified For Gasoline Engines” by the American Petroleum Institute (API).
BATTERY Y our vehicle is equipped with a Motorcraft 威 maintenance-free battery which normally does not require additional water during its life of service. If your battery has a cover/shield, make sure it is reinstalled after the battery has been cleaned or replaced.
W ARNING: Keep batteries out of reach of children. Batteries contain sulfuric acid. A void contact with skin, eyes or clothing. Shield your eyes when working near the battery to protect against possible splashing of acid solution.
If the battery has been disconnected or a new battery has been installed, the clock and radio settings must be reset once the battery is reconnected. • Always dispose of automotive batteries in a responsible manner . Follow your local authorized standards for disposal.
When the engine is cold, check the level of the engine coolant in the reservoir . • The engine coolant should be at the FULL COLD level or within the COLD FILL RANGE as listed on the engine coolant reservoir (depending upon application). • Refer to scheduled maintenance information for service interval schedules.
• Do not mix coolants. Add the coolant type originally equipped in your vehicle. Refer to Maintenance product specifications and capacities in this chapter . Note: Do not use stop leak pellets or cooling system sealants/additives as they can cause damage to the engine cooling and/or heating systems.
4. When you are sure that all the pressure has been released, use the cloth to turn it counterclockwise and remove the cap. 5. Fill the coolant reservoir slowly with the proper coolant mixture, to within the COLD FILL RANGE or the FULL COLD level on the reservoir .
• NEVER increase the coolant concentration above 60%. • Increased engine coolant concentrations above 60% will decrease the overheat protection characteristics of the engine coolant and may cause engine damage.
• The light will illuminate. If the engine reaches a preset over -temperature condition, the engine will automatically switch to alternating cylinder operation. Each disabled cylinder acts as an air pump and cools the engine. When this occurs the vehicle will still operate.
WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELS Important safety precautions W ARNING: Do not overfill the fuel tank. The pressure in an overfilled tank may cause leakage and lead to fuel spray and fire.
• Fuels can also be harmful if absorbed through the skin. If fuel is splashed on the skin and/or clothing, promptly remove contaminated clothing and wash skin thoroughly with soap and water . Repeated or prolonged skin contact with fuel liquid or vapor causes skin irritation.
W ARNING: When refueling always shut the engine off and never allow sparks or open flames near the filler neck. Never smoke while refueling. Fuel vapor is extremely hazardous under certain conditions. Care should be taken to avoid inhaling excess fumes.
When fueling your vehicle: 1. T urn the engine off. 2. Open the fuel filler door . 3. Slowly insert the fuel filler nozzle fully into the fuel system. Pump fuel as normal. 4. After you are done pumping fuel, slowly remove the fuel filler nozzle—allow about five seconds after pumping fuel before removing the fuel filler nozzle.
Flex Fuel V ehicle (FFV) fuel fill inlet If your vehicle is flex fuel capable, it will have a yellow bezel placed over the fuel fill inlet. Choosing the right fuel If your vehicle is a flexible fuel vehicle (FFV), use only UNLEADED FUEL and FUEL ETHANOL (Ed75–Ed85).
Do not be concerned if your engine sometimes knocks lightly . However , if it knocks heavily under most driving conditions while you are using fuel with the recommended octane rating, see your authorized dealer to prevent any engine damage.
Cleaner air Ford endorses the use of reformulated “cleaner -burning” gasolines to improve air quality , per the recommendations in the Choosing the right fuel section. Running out of fuel A void running out of fuel because this situation may have an adverse effect on powertrain components.
1. Locate the white plastic funnel. It is located under the second row driver side seat near the spare tire tool box. 2. Slowly insert the funnel into the Easy Fuel™ system. 3. Fill the vehicle with fuel from the portable fuel container . 4. When done, clean the funnel or properly dispose of it.
vehicle after the fuel gauge indicates empty , you might not be able to refuel the full amount of the advertised capacity of the fuel tank due to the empty reserve still present in the tank.
Habits • Smooth, moderate operation can yield up to 10% savings in fuel. • Steady speeds without stopping will usually give the best fuel economy . • Idling for long periods of time (greater than one minute) may waste fuel. • Anticipate stopping; slowing down may eliminate the need to stop.
• Adding certain accessories to your vehicle (for example bug deflectors, rollbars/light bars, running boards, ski/luggage racks) may reduce fuel economy . • T o maximize the fuel economy , drive with the tonneau cover installed (if equipped). • Using fuel blended with alcohol may lower fuel economy .
If other than Ford, Motorcraft 威 or Ford-authorized parts are used for maintenance replacements or for service of components affecting emission control, such non-Ford parts should be equivalent to genuine Ford Motor Company parts in performance and durability .
2. Poor fuel quality or water in the fuel—the engine may misfire or run poorly . 3. The fuel fill inlet may not have been properly closed. See Easy Fuel™ “no cap” fuel system in this chapter . 4. Driving through deep water—the electrical system may be wet.
The OBD-II system is designed to check the emission control system during normal driving. A complete check may take several days. If the vehicle is not ready for I/M testing, the following driving cyc.
BRAKE FLUID The fluid level will drop slowly as the brakes wear , and will rise when the brake components are replaced. Fluid levels between the MIN and MAX lines are within the normal operating range; there is no need to add fluid.
7. Remove the dipstick and inspect the fluid level. The fluid should be in the designated area for normal operating temperature or ambient temperature. Low fluid level Do not drive the vehicle if the fluid level is at the bottom of the dipstick and the ambient temperature is above 50°F (10°C).
Adjusting automatic transmission fluid levels Before adding any fluid, make sure the correct type is used. The type of fluid used is normally indicated on the dipstick. Refer to Maintenance product specifications and capacities in this chapter . Use of a non-approved automatic transmission fluid may cause internal transmission component damage.
T RANSFER CASE FLUID (IF EQUIPPED) 1. Clean the filler plug. 2. Remove the filler plug and inspect the fluid level. 3. Add only enough fluid through the filler opening so that the fluid level is at the bottom of the opening. Use only fluid that meets Ford specifications.
Changing the air filter element 1. Locate the mass air flow sensor electrical connector on the air outlet tube. This connector will need to be unplugged. 2. Reposition the locking clip on the connector (connector shown from below for clarity), squeeze the connector and pull it off of the air outlet tube.
5. Release the three clamps that secure the cover to the air filter housing. Push the air filter cover toward the center of the vehicle and up slightly to release it. 6. Remove the air filter element from the air filter housing. 7. Install a new air filter element.
10. Reconnect the mass air flow sensor electrical connector to the outlet tube. Make sure the locking tab on the connector is in the “locked” position (connector shown from below for clarity). Note: Failure to use the correct air filter element may result in severe engine damage.
MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIES Item Capacity Ford part name or equivalent Ford part number / Ford specification Brake fluid Between MIN/MAX on brake fluid reservoir Motorcraft 威 High Performance DOT 3 Motor V ehicle Brake Fluid PM-1-C / WSS-M6C62-A or WSS-M6C65-A1 4.
Item Capacity Ford part name or equivalent Ford part number / Ford specification Cooling system stop leak pellets — Motorcraft 威 Cooling System Stop Leak Pellets VC-6 / WSS-M99B37-B6 Front axle (4X4) 3.5 pints (1.8L) Motorcraft 威 SAE 80W -90 Premium Rear Axle Lubricant XY -80W -90-QL / WSP-M2C197-A Rear 8.
Item Capacity Ford part name or equivalent Ford part number / Ford specification Automatic transmission fluid (6R80) 12.1 quarts (11.4L) 6 (4.6L 3V engine) Motorcraft 威 MERCON 威 LV AT F 7 XT -10-QL V / MERCON 威 LV 13.1 quarts (12.4L) (5.4L engine) W indshield washer fluid 4.
Item Capacity Ford part name or equivalent Ford part number / Ford specification Fuel tank Reg. Cab 8’ box / SuperCab 6.5’ box / SuperCab 8’ box 26.0 gallons (98.4L) Standard 36.0 gallons (136.2L) Optional —— 1 Use of synthetic or synthetic blend motor oil is not mandatory .
ENGINE DATA Engine 4.6L 2V V8 engine 4.6L 3V V8 engine 5.4L V8 engine Cubic inches 281 281 330 Fuel 87 octane 87 octane 87 octane or Ethanol (E85) Firing order 1-3-7-2-6-5-4-8 1-3-7-2-6-5-4-8 1-3-7-2-6-5-4-8 Ignition system Coil on plug Coil on plug Coil on plug Spark plug gap 0.
Engine drivebelt routing IDENTIFYING YOUR VEHICLE Safety Compliance Certification Label The National Highway T raffic Safety Administration Regulations require that a Safety Compliance Certification Label be affixed to a vehicle and prescribe where the Safety Compliance Certification Label may be located.
V ehicle identification number (VIN) The vehicle identification number is located on the driver side instrument panel. Please note that in the graphic, XXXX is representative of your vehicle identification number . The V ehicle Identification Number (VIN) contains the following information: 1.
T RANSMISSION CODE DESIGNATIONS Y ou can find a transmission code on the Safety Compliance Certification Label. The following table tells you which transmission each code represents.
GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for your vehicle through your local Ford or Ford of Canada dealer .
Bed side step Interior cargo organization and management T ruck bed cargo organization and management T owing mirrors T railer hitches, wiring harnesses and accessories Peace of mind Keyless entry key.
FORD ESP EXTENDED SERVICE PLANS More than 30 million Ford, Lincoln, and Mercury owners have discovered the powerful protection of Ford ESP . It is the only extended service plan backed by Ford Motor Company , and provides “peace of mind” protection beyond the New V ehicle Limited W arranty coverage.
Ford ESP Can Quickly Pay for Itself One service bill – the cost of parts and labor – can easily exceed the price of your Ford ESP Service Contract.
Ford Extended Service Plan 412 2010 F-150 (f12) Owners Guide, 1st Printing USA (fus).
A Accessory delay .......................... 93 AdvanceT rac .............................. 279 Air cleaner filter ....... 396–397, 399 Air conditioning ........59, 62, 64, 67 manual heating and air conditioning system ................. 59 Airbag supplemental restraint system .
Child safety seats ......................204 attaching with tether straps .. 214 in front seat .................... 205, 211 in rear seat ...................... 205, 211 LA TCH ..................................... 212 recommendations ................
coolant ..................................... 373 fail-safe cooling ....................... 377 idle speed control ................... 371 lubrication specifications ....... 400 refill capacities ........................ 400 service points ...........
Heating heating and air conditioning system ..................... 59, 62, 64, 67 Homelink wireless control system ........................................ 104 Hood .......................................... 364 I Ignition ....................... 271, 404–405 Illuminated visor mirror .
MyKey ........................................ 141 N Navigation system ....................... 58 O Octane rating .................... 383–384 Oil (see Engine oil) .................. 368 P Parental MyKey programming ............................. 141 Parking brake .
Safety restraints - LA TCH anchors ...................................... 212 Safety seats for children .......... 204 Safety Compliance Certification Label .................... 405 Satellite Radio (if equipped) .....42 Satellite Radio Information ...
T ransmission ............................. 291 brake-shift interlock (BSI) ................................287, 289 fluid, checking and adding (automatic) ..................... 393, 395 fluid, refill capacities .............. 400 lubricant specifications .
Een belangrijk punt na aankoop van elk apparaat Ford 2010 F-150 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Ford 2010 F-150 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Ford 2010 F-150 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Ford 2010 F-150 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Ford 2010 F-150 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Ford 2010 F-150 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Ford 2010 F-150 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Ford 2010 F-150 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
