Gebruiksaanwijzing /service van het product 2011 Focus van de fabrikant Ford
Ga naar pagina of 301
Introduction 4 Instrument Cluster 12 W arning lights and chimes 12 Gauges 17 Message center 19 Entertainment Systems 25 AM/FM stereo with CD/MP3 25 Auxiliary input jack (Line in) 33 USB port 35 Satell.
Seating and Safety Restraints 88 Seating 88 Safety restraints 95 Airbags 110 Child restraints 125 Tires, Wheels and Loading 144 T ire information 144 T ire inflation 146 T ire Pressure Monitoring Syst.
Maintenance and Specifications 227 Engine compartment 229 Engine oil 231 Battery 233 Engine coolant 235 Fuel information 241 Air filter(s) 255 Part numbers 258 Maintenance product specifications and c.
CONGRATULATIONS Congratulations on acquiring your new Ford. Please take the time to get well acquainted with your vehicle by reading this handbook. The more you know and understand about your vehicle, the greater the safety and pleasure you will derive from driving it.
W arning symbols on your vehicle When you see this symbol, it is imperative that you consult the relevant section of this guide before touching or attempting adjustment of any kind. Protecting the environment W e must all play our part in protecting the environment.
SPECIAL NOTICES New V ehicle Limited W arranty For a detailed description of what is covered and what is not covered by your vehicle’ s New V ehicle Limited W arranty , refer to the Warranty Guide that is provided to you along with your Owner’ s Guide.
systems. In order to properly diagnose and service your vehicle, Ford Motor Company , Ford of Canada, and service and repair facilities may access or share among them vehicle diagnostic information received through a direct connection to your vehicle when diagnosing or servicing your vehicle.
T o read data recorded by an EDR, special equipment is required, and access to the vehicle or the EDR is needed. In addition to the vehicle manufacturer , other parties, such as law enforcement, that have such special equipment, can read the information if they have access to the vehicle or the EDR.
CELL PHONE USE The use of Mobile Communications Equipment has become increasingly important in the conduct of business and personal affairs. However , drivers must not compromise their own or others’ safety when using such equipment.
These are some of the symbols you may see on your vehicle. V ehicle Symbol Glossary Safety Alert See Owner’ s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat Lower Anchor Child Seat.
V ehicle Symbol Glossary Power W indows Front/Rear Power W indow Lockout Child Safety Door Lock/Unlock Interior Luggage Compartment Release Panic Alarm Engine Oil Engine Coolant Engine Coolant T emper.
W ARNING LIGHTS AND CHIMES W arning lights and gauges can alert you to a vehicle condition that may become serious enough to cause expensive repairs. A warning light may illuminate when a problem exists with one of your vehicle’ s functions. Many lights will illuminate when you start your vehicle to make sure the bulb works.
W ARNING: Under engine misfire conditions, excessive exhaust temperatures could damage the catalytic converter , the fuel system, interior floor coverings or other vehicle components, possibly causing a fire. Check fuel cap: Illuminates when the fuel cap may not be properly installed.
Airbag readiness: If this light fails to illuminate when the ignition is turned to on, continues to flash or remains on, have the system serviced immediately by your authorized dealer . A chime will sound when there is a malfunction in the indicator light.
Overdrive off (if equipped): Illuminates when the overdrive function of the transmission has been turned off, refer to the Driving chapter . If the light flashes steadily or does not illuminate, have the transmission serviced soon, or damage may occur .
Low fuel: Illuminates when the fuel level in the fuel tank is at or near empty (refer to Fuel gauge in this chapter). Door ajar: Illuminates when the ignition is on and any door , the trunk or hood is open. T urn signal: Illuminates when the left or right turn signal or the hazard lights are turned on.
GAUGES Speedometer: Indicates the current vehicle speed. Engine coolant temperature gauge: Indicates engine coolant temperature. At normal operating temperature, the needle will be in the normal range. If it enters the red section, the engine is overheating.
Odometer: Registers the total miles (kilometers) of the vehicle. If equipped with a message center , refer to Message center in this chapter on how to switch the display between Metric and English. T rip odometer: Registers the distance of individual journeys.
MESSAGE CENTER Y our vehicle’ s message center is capable of monitoring many vehicle systems and will alert you to potential vehicle problems and various conditions with an informational message followed by a long indicator chime. The message center display is located in the instrument cluster .
A VG MPG (L/100km) A verage fuel economy displays your average fuel economy in miles/gallon or liters/100 km. If you calculate your average fuel economy by dividing distance traveled by gallons of fue.
1. CHARGING SYSTEM 2. DOORS 3. TRUNK 4. BRAKE SYSTEM 5. DTE/FUEL LEVEL 6. MYKEY DIST ANCE (if programmed) 7. MYKEY(S) PROGRAMMED 8. ADMIN KEYS PROGRAMMED Note: Some systems show a message only if a condition is present. UNITS Displays the current units in English or Metric.
System warnings System warnings alert you to possible problems or malfunctions in your vehicle’ s operating systems. In the event of a multiple warning situation, the message center will cycle the display to show all warnings by displaying each one for four seconds.
CHECK BRAKE SYSTEM — Displayed when the braking system is not operating properly . If the warning stays on or continues to come on, contact your authorized dealer as soon as possible. BRAKE FLUID LEVEL LOW — Indicates the brake fluid level is low and the brake system should be inspected immediately .
VEHICLE NEAR TOP SPEED — Displayed when a MyKey™ is in use and the MyKey speed limit is on and the vehicle speed is approaching 80 mph (130 km/h). Refer to MyKey™ in the Locks and Security chapter for more information.
AUDIO SYSTEMS AM/FM/single CD satellite compatible sound system W ARNING: Driving while distracted can result in loss of vehicle control, accident and injury . Ford strongly recommends that drivers use extreme caution when using any device or feature that may take their focus off the road.
AM/FM Radio / VOL (Power/V olume): Press to turn the radio on/off. T urn the knob to increase/decrease volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a nominal listening level when the ignition switch is turned back on.
another control within those five seconds, the search will not initiate. The 10 strongest stations will be filled and the station stored in preset 1 will begin playing. If there are fewer than 10 strong stations, the system will store the last one in the remaining presets.
SEEK/TRACK: Press SEEK/TRACK to access the previous/next track. CA T (Category) / FOLD (Folder): In MP3 mode only– Press CA T/FOLD and then press SEEK/TRACK to access the previous/next folder . SCAN: Press for a brief sampling of all tracks on the current disc or MP3 folder .
Satellite Radio (if equipped) Satellite radio is available only with a valid SIRIUS radio subscription. Check with your authorized dealer for availability . SIRIUS: Press repeatedly to access satellite radio mode, if equipped. Press repeatedly to cycle through SA T1, SA T2 and SA T3 modes.
In TEXT MODE: Sometimes the display requires additional text to be displayed. When th e</>i n d i c a t o ri sa c t i v e ,p r e s s TEXT and then press SEEK/TRACK to view the additional display text. CA T (Category) / FOLD (Folder): Press to switch between turning the most recently selected satellite radio category on or off.
The song will appear in the display for confirmation. Press OK again and the display will read SONG DELETED. If you do not want to delete the currently listed song, press / to select either RETURN or CANCEL. Note: If there are no songs presently saved, the display will read NO SONGS.
PIN number to its initial password setting (1234). PIN RESET TO DEF AUL T PIN will be displayed. e. RETURN: Press OK when RETURN is displayed and the system will exit back to the satellite radio menu. Sound Adjustments Press SOUND repeatedly to cycle through the following features: BASS: Press SEEK/TRACK to adjust the level of bass.
OK: Y our vehicle may be equipped with special phone and media features which will require you to confirm commands by pressing OK. Refer to the SYNC 威 information included with your vehicle for further information. (Phone): If your vehicle is equipped with SYNC 威 , press to access SYNC PHONE features.
T o play your portable music player using the auxiliary input jack: 1. Begin with the vehicle parked and the radio turned off. 2. Ensure that the battery in your portable music player is new or fully charged and that the device is turned off.
location, such as the center console or the glove box, when the vehicle is in motion. The audio extension cable must be long enough to allow the portable music player to be safely stored while the vehicle is in motion. USB port (if equipped) W ARNING: Driving while distracted can result in loss of vehicle control, accident and injury .
CD/CD player care Do: • Handle discs by their edges only . (Never touch the playing surface). • Inspect discs before playing. • Clean only with an approved CD cleaner . • W ipe discs from the center out. Don’t: • Expose discs to direct sunlight or heat sources for extended periods of time.
CDs with homemade paper (adhesive) labels should not be inserted into the CD player as the label may peel and cause the CD to become jammed. It is recommended that homemade CDs be identified with permanent felt tip marker rather than adhesive labels. Ballpoint pens may damage CDs.
Sample MP3 structure If you are burning your own MP3 discs, it is important to understand how the system will read the structures you create. While various files may be present, (files with extensions other than mp3), only files with the .mp3 extension will be played.
Satellite radio reception factors: T o receive the satellite signal, your vehicle has been equipped with a satellite radio antenna located on the roof of your vehicle. The vehicle roof provides the best location for an unobstructed, open view of the sky , a requirement of a satellite radio system.
Satellite radio electronic serial number (ESN): This 12–digit Satellite Serial Number is needed to activate, modify or track your satellite radio account.
Radio Display Condition Action Required NO TEXT Song title information not available. Song title information not available at this time on this channel. The system is working properly . NO TEXT Category information not available. Category information not available at this time on this channel.
MANUAL HEATING AND AIR CONDITIONING SYSTEM 1. Fan speed adjustment: Controls the volume of air circulated in the vehicle. 2. R Rear defroster: Press to activate/deactivate the rear window defroster . Refer to Rear window defroster later in this chapter for more information.
7. : Distributes air through the instrument panel vents, floor vents, rear seat floor vents and demister vents. 8. : Distributes air through the floor vents, rear seat floor vents and demister vents. 9. T emperature control: Controls the temperature of the airflow in the vehicle.
Operating tips • T o reduce fog build-up on the windshield during humid weather , select (defrost) or (floor/defrost). • T o reduce humidity build-up inside the vehicle, do not drive with the system off or with (recirculated air) engaged and A/C off.
REAR WINDOW DEFROSTER R The rear defroster control is located on the climate control panel and works to clear the rear window of fog and thin ice. The engine must be running to operate the rear window defroster . Press R to turn the rear window defroster on.
HEADLAMP CONTROL T urns the lamps off. T urns on the parking lamps, instrument panel lamps, license plate lamps and tail lamps. T urns the low beam headlamps on. Fog lamp control (if equipped) The fog lamps can be turned on when the headlamp control is in the or position and the high beams are not turned on.
Flash-to-pass Pull toward you slightly to activate and release to deactivate. Daytime running lamps (DRL) (if equipped) T urns the headlamps on with a reduced output. T o activate: • the ignition must be in the on position and • the headlamp control is in the off or parking lamp position.
AIMING THE HEADLAMPS The headlamps on your vehicle are properly aimed at the assembly plant. If your vehicle has been in an accident, the alignment of your headlamps should be checked by your authorized dealer . V ertical aim adjustment 1. Park the vehicle directly in front of a wall or screen on a level surface, approximately 25 feet (7.
5. Locate the vertical adjuster on each headlamp, then use a Phillips #2 screwdriver or 10 mm wrench/socket to adjust the headlamp up or down. 6. Close the hood and turn off the lamps. HORIZONT AL AIM IS NOT REQUIRED FOR THIS VEHICLE AND IS NON-ADJUST ABLE.
Rear dome lamp When the lamp control is in the middle position, the rear dome lamp will come on when a door is opened or the unlock button is pressed on the remote keyless entry . If the control is moved to the driver side position, the lamp will not come on at all.
Examples of acceptable condensation are: • Presence of thin mist (no streaks, drip marks or droplets) • Fine mist covers less than 50% of the lens Examples of unacceptable moisture (usually caused.
Replacing headlamp bulbs 1. Make sure the headlamp control is in the off position and open the hood. 2. Remove four push pins from the radiator grille and pull the grille forward to access the lower screw . 3. Remove three bolts and washers from the headlamp assembly .
Replacing front parking lamp/turn signal bulbs 1. Make sure the headlamp control is in the off position and open the hood. 2. Remove four push pins from the radiator grille and pull the grille forward to access the lower screw . 3. Remove three bolts and washers from the headlamp assembly .
5. Remove the bulb socket from the lamp assembly by turning counterclockwise. 6. Pull the bulb straight out of the socket. Install the new bulb in reverse order . Be sure that the spring clip is not damaged or detached from the housing during the replacement procedure.
Replacing license plate lamp bulbs 1. Make sure the headlamp switch is in the off position. 2. Remove the two screws and the lens from the license plate lamp assembly . 3. Carefully pull the bulb straight out from the lamp assembly . Install new bulb(s) in reverse order .
MULTI-FUNCTION LEVER W indshield wiper: Rotate the end of the control away from you to increase the speed of the wipers; rotate towards you to decrease the speed of the wipers. W indshield washer: Press the end of the stalk: • briefly: causes a single swipe of the wipers without washer fluid.
TILT STEERING WHEEL T o adjust the steering wheel: 1. Pull the lever down to unlock the steering column. 2. While the lever is in the down position, move the steering wheel up or down until you find the desired position. 3. While holding the steering wheel in place, pull the lever up to its original position to lock the steering column.
Compass zone adjustment 1. Determine which magnetic zone you are in for your geographic location by referring to the zone map. 2. T urn ignition to the on position. 3. Press and hold the 7 and 9 radio preset buttons together for approximately five seconds until ZONE XX appears in the CID.
2. T o calibrate, press and hold the 7 and 9 radio preset buttons together for approximately 10 seconds until CAL appears. Release the buttons. 3. Slowly drive the vehicle in a circle (less than 3 mph [5 km/h]) until the CAL display changes to the direction value (N, S, E, W , etc.
T o have full capacity usage of your power point, the engine is required to be running to avoid unintentional discharge of the battery . T o prevent the battery from being discharged: • do not use t.
Window lock (if equipped) The window lock feature allows only the driver to operate the power windows. T o lock out all the window controls (except for the driver’ s) press the right side of the control. Press the left side to restore the window controls.
EXTERIOR MIRRORS Power side view mirrors (if equipped) W ARNING: Do not adjust the mirror while the vehicle is in motion. T o adjust your mirrors: 1. Rotate the control clockwise to adjust the right mirror and rotate the control counterclockwise to adjust the left mirror .
Using speed control The speed controls are located on the steering wheel. The following buttons work with speed control: RESUME: Press to resume a set speed. SET +: Press to set a speed or increase a set speed. SET –: Press to decrease a set speed. OFF: Press to turn speed control off.
Increasing speed while using speed control T o set a higher speed: • Press and hold SET + until you get to the desired speed, then release. Y ou can also use SET + to operate the tap-up function. Press and release SET + to increase the vehicle set speed in 1 mph (1.
SYNC 威 hands free control feature (if equipped) Press briefly to use the voice command feature. Y ou will hear a tone and LISTENING will appear in the radio display . Press and hold to exit voice command. Press to activate phone mode or answer a phone call.
T o open the moon roof: Press and release the SLIDE control. The moon roof will open to the “comfort” position. Press and release the control again to fully open.
• Release the switch and immediately press and hold it again. The moon roof will close, open fully and then close again. Do not release the switch before the moon roof has reached the closed position for the second time. Safety mode: If the system detects a malfunction, it enters a safety mode.
KEYS One key operates all the locks and starts the vehicle. Always carry a spare key with you in case of an emergency . Y our keys are programmed to your vehicle; using a non-programmed key will not permit your vehicle to start. If you lose your authorized dealer supplied keys, replacement keys are available through your authorized dealer .
• The AdvanceT rac 威 system cannot be turned off. When this optional setting is on, the MyKey™ user will not be able to deactivate the system. Note: It may be beneficial to deactivate the AdvanceT rac 威 system if the vehicle is stuck in snow , mud or sand.
4. On any of the menus press RESET to highlight your choice with the <…>. 5. Press SETUP to enter your choice. The next optional setting will be displayed. 6. Repeat Steps 4 and 5 until you are done changing the optional settings. Clear MyKey™ T o reset all MyKeys™ as admin keys, do the following: 1.
V ehicles equipped with traditional keys: When using a Ford-approved remote start system, the default settings will recognize the remote start system as an additional admin key with its associated privileges.
T roubleshooting Condition Potential Causes Can’t create a MyKey™ • Key in the ignition is already a MyKey™. • Key in the ignition is the last remaining admin key (there always has to be at least one admin key). • Intelligent access key (if equipped) not in the backup slot — for vehicles with push button start.
Condition Potential Causes No MyKey™ function with intelligent access key (push button start) (if equipped) • An admin key is present at vehicle start • No MyKeys™ are programmed to the vehicle.
The vehicle can still be locked, with the key in the ignition, by locking the driver’ s door with a key or using the lock control on the remote entry key fob. If both front doors are closed, the vehicle can be locked from any method, regardless of whether the key is in the ignition or not.
Power door unlock/lock procedure Before starting, ensure the ignition is in the off position and all vehicle doors are closed. Y ou must complete Steps 1–5 within 30 seconds or the procedure will have to be repeated. If the procedure needs to be repeated, wait a minimum of 30 seconds before beginning again.
Deactivating/activating autounlock feature Y our vehicle comes with the autounlock features activated; there are three methods to enable/disable this feature: • Through your authorized dealer , • by using a power door unlock/lock sequence • or by using the instrument cluster message center .
CHILDPROOF DOOR LOCKS • When these locks are set, the rear doors cannot be opened from the inside. • The rear doors can be opened from the outside when the childproof door locks are set, but the doors are unlocked. The childproof locks are located on the rear edge of each rear door and must be set separately for each door .
T o open the luggage compartment door (lid) from within the luggage compartment, pull the illuminated “T” shaped handle and push up on the trunk lid. The handle is composed of a material that will glow for hours in darkness following brief exposure to ambient light.
REMOTE ENTRY SYSTEM This device complies with part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
The remote entry system activates the illuminated entry feature. This feature turns on the lamps for 25 seconds or until the ignition is turned to the on position. The dome lamp control must be set to the ON position in order for the illuminated entry feature to operate.
• Ensure that the trunk is closed and latched before driving your vehicle. Failure to properly latch the trunk may cause objects to fall out or block the driver’ s rear view . Replacing the battery The remote entry transmitter uses one coin type three-volt lithium battery CR2032 or equivalent.
How to reprogram your remote entry transmitters Y ou must have all remote entry transmitters (maximum of four) available before beginning this procedure. If all remote entry transmitters are not present during the programming procedure, the transmitters that are not present during programming will no longer operate the vehicle.
The lights will not turn off if: • they have been turned on with the dimmer control, or • any door is open. Illuminated exit • When all vehicle doors and the trunk are closed, and the key is removed from the ignition, the interior lamps and parking lamps will illuminate.
Note: Large metallic objects, electronic devices that are used to purchase gasoline or similar items, or a second coded key on the same key chain may cause vehicle starting issues. Y ou need to prevent these objects from touching the coded key while starting the engine.
Programming spare keys Y ou can program your own coded keys to your vehicle. Please read and understand the entire procedure before you begin. T ips: • A maximum of eight keys can be coded to your vehicle.
10. T urn the ignition from the 1 (off) position to the 3 (on) position. Keep the ignition in the 3 (on) position for at least one second, but no more than 10 seconds.
Disarming the system Y ou can disarm the system by any of the following actions: • Unlock the doors by pressing the control on your remote entry transmitter . • T urn the ignition to the on or start position with a programmed coded ignition key . • Press the panic control on the remote entry transmitter .
FRONT SEATING W ARNING: Reclining the seatback can cause an occupant to slide under the seat’ s safety belt, resulting in severe personal injuries in the event of a collision. W ARNING: Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop.
T o adjust the head restraint, do the following: 1. Adjust the seatback to an upright driving/riding position. 2. Raise the head restraint by pulling up on the head restraint. 3. Lower the head restraint by pressing and holding the guide sleeve adjust release button and pushing down on the head restraint.
T o remove the adjustable head restraint, do the following: 1. Pull up the head restraint until it reaches the highest adjustment position. 2. Simultaneously press and hold both the adjust/release button and the unlock/remove button, then pull up on the head restraint.
W ARNING: T o minimize the risk of neck injury in the event of a crash, head restraints must be installed properly . Adjusting the front manual seat W ARNING: Sitting improperly out of position or wit.
Pull up on the control to raise the seat and push down on the control to lower the seat. Lift the control to adjust the angle of the seatback. W ARNING: Reclining the seatback can cause an occupant to slide under the seat’ s safety belt, resulting in severe personal injuries in the event of a collision.
Heated seats (if equipped) W ARNING: Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury , medication, alcohol use, exhaustion, or other physical conditions, must exercise care when using the seat heater .
Tip/slide front passenger seat (if equipped) Lift the control and fold the seatback forward. The seat can be slid forward to allow easier entry to the rear seats. Slide the seat back and fold back the seatback until it locks with a distinct click. Rock the seat to ensure that the catch is securely engaged.
Folding down the rear seat One or both rear seatbacks can be folded down to provide additional cargo space. T o lower the seatback(s) from inside the vehicle, do the following: 1.
• Driver’ s seat position sensor . • Front crash severity sensor . • Front passenger sensing system • “Passenger airbag off” or “pass airbag off” indicator lamp • Restraints Control Module (RCM) with impact and safing sensors. • Restraint system warning light and backup tone.
Driver ’s seat position sensor The driver’ s seat position sensor allows your Personal Safety System to tailor the deployment level of the driver dual-stage airbag based on seat position. The system is designed to help protect smaller drivers sitting close to the driver airbag by providing a lower airbag output level.
Front safety belt usage sensors The front safety belt usage sensors detect whether or not the driver and front outboard passenger safety belts are fastened. This information allows your Personal Safety System to tailor the airbag deployment and safety belt pretensioner activation depending upon safety belt usage.
If any of these things happen, even intermittently , have the Personal Safety System™ serviced at an authorized dealer immediately . Unless serviced, the system may not function properly in the event of a collision. Safety belt precautions W ARNING: Always drive and ride with your seatback upright and the lap belt snug and low across the hips.
W ARNING: When possible, all children 12 years old and under should be properly restrained in a rear seating position. W ARNING: Front and rear seat occupants, including pregnant women, should wear safety belts for optimum protection in an accident. Combination lap and shoulder belts 1.
Pregnant women should always wear their safety belt. The lap belt portion of a combination lap and shoulder belt should be positioned low across the hips below the belly and worn as tight as comfort will allow . The shoulder belt should be positioned to cross the middle of the shoulder and the center of the chest.
When to use the automatic locking mode This mode should be used any time a child safety seat, except a booster , is installed in passenger front or rear seating positions. Children 12 years old and under should be properly restrained in a rear seating position whenever possible.
W ARNING: After any vehicle collision, the safety belt system at all passenger seating positions must be checked by an authorized dealer to verify that the “automatic locking retractor” feature for child seats is still functioning properly . In addition, all safety belts should be checked for proper function.
2. Be sure the belt is not twisted. If the belt is twisted, remove the twist. 3. Insert the belt tongue into the proper buckle for your seating position until you hear a snap and feel it latch. 4. Make sure the tongue is securely fastened to the buckle by pulling on the tongue.
W ARNING: Position the safety belt height adjusters so that the belt rests across the middle of your shoulder . Failure to adjust the safety belt properly could reduce the effectiveness of the seat belt and increase the risk of injury in a collision.
Conditions of operation If... Then... The driver’ s safety belt is not buckled before the ignition switch is turned to the on position... The safety belt warning light illuminates 1-2 minutes and the warning chime sounds 4-8 seconds. The driver’ s safety belt is buckled while the indicator light is illuminated and the warning chime is sounding.
If... Then... The driver’ s and front passenger’ s safety belts are buckled before the ignition switch is turned to the on position or less than 1-2 minutes have elapsed since the ignition switch has been turned to on... The Belt-Minder 威 feature will not activate.
The following are reasons most often given for not wearing safety belts (All statistics based on U.S. data): Reasons given... Consider ... “Crashes are rare events” 36700 crashes occur every day . The more we drive, the more we are exposed to “rare” events, even for good drivers.
W ARNING: Do not sit on top of a buckled safety belt or insert a latchplate into the buckle to avoid the Belt-Minder 威 chime. T o do so may adversely affect the performance of the vehicle’ s airbag system. Deactivating/activating the Belt-Minder 姞 feature The driver and front passenger Belt-Minder 威 are deactivated/activated independently .
• Step 3 must be completed within 50 seconds after the safety belt warning light turns off. 3. For the seating position being disabled, buckle then unbuckle the safety belt nine times at a moderate speed, ending in the unbuckled state. • After Step 3, the safety belt warning light will be turned on for three seconds.
Important SRS precautions The SRS is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries.
W ARNING: Do not attempt to service, repair , or modify the airbag supplemental restraint systems or its fuses. Contact your authorized dealer as soon as possible.
The airbags inflate and deflate rapidly upon activation. After airbag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder (to lubricate the bag) or sodium compounds (e.
• safety belt pretensioners • one or more impact and safing sensors. • Front passenger sensing system. Refer to Front passenger sensing system later in this chapter . • “Passenger airbag off” or “pass airbag off” indicator lamp. Refer to Front passenger sensing system later in this chapter .
Note: When the passenger airbag off light is illuminated, the passenger (seat mounted) side airbag may be disabled to avoid the risk of airbag deployment injuries.
• Restart the vehicle and have the person remain in this position for about two minutes. This will allow the system to detect that person and enable the passenger’ s frontal airbag. • If the indicator lamp remains lit even after this, the person should be advised to ride in the rear seat.
Objects Pass Airbag Off Indicator Lamp Passenger Airbag Small (i.e. three-ring binder , small purse, bottled water) Unlit Disabled Medium (i.e. heavy briefcase, fully packed luggage) Lit Disabled Empt.
In case there is a problem with the front passenger sensing system, the airbag readiness lamp in the instrument cluster will stay lit. If the airbag readiness lamp is lit, do the following: The driver and/or adult passengers should check for any objects that may be lodged underneath the front passenger seat or cargo interfering with the seat.
A difficulty with the system is indicated by one or more of the following: • The readiness light (same light for front and side airbag system) will either flash or stay lit. • The readiness light will not illuminate immediately after ignition is turned on.
How does the side airbag system work? The design and development of the side airbag system included recommended testing procedures that were developed by a group of automotive safety experts known as the Side Airbag T echnical W orking Group.
W ARNING: Several air bag system components get hot after inflation. Do not touch them after inflation. W ARNING: If the side airbag has deployed, the airbag will not function again. The side airbag system (including the seat) must be inspected and serviced by an authorized dealer .
W ARNING: Do not attempt to service, repair , or modify the side air curtain system, its fuses, the A, B, or C pillar trim, or the headliner on a vehicle containing a side air curtain.
• T wo pressure sensors located in the front doors. • T wo crash sensors located on the rocker panel between the “B” and “C” pillars near the floor . Side air curtains and side airbags, in combination with safety belts, can help reduce the risk of severe injuries in the event of a significant side impact collision.
W ARNING: If the side air curtain has deployed, the air curtain will not function again. The side air curtain system (including the A, B and C pillar trim and headliner) must be inspected and serviced by an authorized dealer . If the air curtain is not replaced, the unrepaired area will increase the risk of injury in a collision.
The feature will continue to operate until the vehicle runs out of power . Disposal of airbags and airbag equipped vehicles (including pretensioners) Contact your authorized dealer as soon as possible. Airbags MUST BE disposed of by qualified personnel.
Recommendations for Safety Restraints for Children Child size, height, weight, or age Recommended restraint type Infants or toddlers Children weighing 40 lb (18 kg) or less (generally age four or younger) Use a child safety seat (sometimes called an infant carrier , convertible seat, or toddler seat).
Recommendations for attaching child safety restraints for children Restraint T ype Child W eight Use any attachment method as indicated below by “X” LA TCH (lower anchors and top tether anchor) LA.
W ARNING: Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision, which may result in serious injury or death. W ARNING: Never use pillows, books, or towels to boost a child.
Follow all the safety restraint and airbag precautions that apply to adult passengers in your vehicle. If the child is the proper height, age, and weight (as specified by your child safety seat or boo.
position whenever possible. If all children cannot be seated and restrained properly in a rear seating position, properly restrain the largest child in the front seat. When installing a child safety seat with combination lap/shoulder belts: • Use the correct safety belt buckle for that seating position.
2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together . 3. While holding the shoulder and lap belt portions together , route the tongue through the child seat according to the child seat manufacturer’ s instructions.
5. T o put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is pulled out. Note: The automatic locking mode is available on the front passenger and rear outboard seats only . The rear center seating position has a cinch tongue.
10. Before placing the child in the seat, forcibly move the seat forward and back to make sure the seat is securely held in place. T o check this, grab the seat at the belt path and attempt to move it side to side and forward and back. There should be no more than 1 inch (2.
2. Slide the tongue up the webbing. 3. While holding both shoulder and lap portions next to the tongue, route the tongue and webbing through the child seat according to the child seat manufacturer’ s instructions. Be sure that the belt webbing is not twisted.
5. Remove remaining slack from the belt. Force the seat down with extra weight, e.g., by pressing down or kneeling on the child restraint while pulling up on the shoulder belt in order to force slack from the belt.
equipped seating positions in your vehicle. This type of attachment method eliminates the need to use safety belts to attach the child seat, however the safety belt can still be used to attach the child seat.
W ARNING: Depending on where you secure a child restraint, and depending on the child restraint design, you may block access to certain safety belt buckle assemblies and/or LA TCH lower anchors, rendering those features potentially unusable.
Attaching child safety seats with tether straps Many forward-facing child safety seats include a tether strap which extends from the back of the child safety seat and hooks to an anchoring point called the top tether anchor . T ether straps are available as an accessory for many older safety seats.
2. Locate the correct anchor for the selected seating position. 3. Open the tether anchor cover . 4. Clip the tether strap to the anchor as shown. If the tether strap is clipped incorrectly , the child safety seat may not be retained properly in the event of a collision.
Although the lap/shoulder belt will provide some protection, children who have outgrown a typical child seat are still too small for lap/shoulder belts to fit properly , and wearing an improperly fitted vehicle safety belt could increase the risk of serious injury in a crash.
T ypes of booster seats There are generally two types of belt-positioning booster seats: backless and high back. Always use booster seats in conjunction with the vehicle lap/shoulder belt. • Backless booster seats If your backless booster seat has a removable shield, remove the shield.
Children and booster seats vary in size and shape. Choose a booster that keeps the lap belt low and snug across the hips, never up across the stomach, and lets you adjust the shoulder belt to cross the chest and rest snugly near the center of the shoulder .
Follow all instructions provided by the manufacturer of the booster seat. W ARNING: Never place, or allow a child to place, the shoulder belt under a child’ s arm or behind the back because it reduces the protection for the upper part of the body and may increase the risk of injury or death in a collision.
INFORMA TION ABOUT UNIFORM TIRE QUALITY GRADING T ire Quality Grades apply to new pneumatic passenger car tires. The Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width.
W ARNING: The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics.
Increasing the inflation pressure beyond this pressure will not increase the tire’ s load carrying capability . • kPa: Kilopascal, a metric unit of air pressure.
W ARNING: Under -inflation is the most common cause of tire failures and may result in severe tire cracking, tread separation or “blowout”, with unexpected loss of vehicle control and increased risk of injury . Under -inflation increases sidewall flexing and rolling resistance, resulting in heat buildup and internal damage to the tire.
when you get to the pump. It is normal for tires to heat up and the air pressure inside to go up as you drive. 2. Remove the cap from the valve on one tire, then firmly press the tire gauge onto the valve and measure the pressure. 3. Add enough air to reach the recommended air pressure.
Improper or inadequate vehicle maintenance can cause tires to wear abnormally . Inspect all your tires, including the spare, frequently , and replace them if one or more of the following conditions ex.
U.S. DOT Tire Identification Number (TIN) Both U.S. and Canada Federal regulations require tire manufacturers to place standardized information on the sidewall of all tires. This information identifies and describes the fundamental characteristics of the tire and also provides a U.
W ARNING: When mounting replacement tires and wheels, you should not exceed the maximum pressure indicated on the sidewall of the tire to set the beads without additional precautions listed below . If the beads do not seat at the maximum pressure indicated, re-lubricate and try again.
• Do not run over curbs or hit the tire against a curb when parking W ARNING: If your vehicle is stuck in snow , mud, sand, etc., do not rapidly spin the tires; spinning the tires can tear the tire and cause an explosion. A tire can explode in as little as three to five seconds.
• Front-wheel drive (FWD) vehicles (front tires at top of diagram) Sometimes irregular tire wear can be corrected by rotating the tires. Note: If your tires show uneven wear ask an authorized dealer to check for and correct any wheel misalignment, tire imbalance or mechanical problem involved before tire rotation.
Information on “P” type tires P215/65R15 95H is an example of a tire size, load index and speed rating. The definitions of these items are listed below . (Note that the tire size, load index and speed rating for your vehicle may be different from this example.
Note: Y ou may not find this information on all tires because it is not required by federal law . Letter rating Speed rating - mph (km/h) M 81 mph (130 km/h) N 87 mph (140 km/h) Q 99 mph (159 km/h) R .
11. Maximum Load: Indicates the maximum load in kilograms and pounds that can be carried by the tire. Refer to the Safety Compliance Certification Label, which is located on the B-Pillar or the edge of the driver’ s door , for the correct tire pressure for your vehicle.
Additional information contained on the tire sidewall for “L T” type tires “L T” type tires have some additional information beyond those of “P” type tires; these differences are described below . Note: T ire Quality Grades do not apply to this type of tire.
Information on “T” type tires “T” type tires have some additional information beyond those of “P” type tires; these differences are described below: T145/80D16 is an example of a tire size. Note: The temporary tire size for your vehicle may be different from this example.
TIRE PRESSURE MONITORING SYSTEM (TPMS) Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label.
following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. W ARNING: The tire pressure monitoring system is NOT a substitute for manually checking tire pressure.
T o restore the full functionality of the tire pressure monitoring system, have the damaged road wheel/tire repaired and remounted on your vehicle. For additional information, refer to Changing tires with TPMS in this section.
Low tire pressure warning light Possible cause Customer action required Flashing warning light Spare tire in use Y our temporary spare tire is in use. Repair the damaged road wheel and re-mount it on the vehicle to restore system functionality .
SNOW TIRES AND CHAINS W ARNING: Snow tires must be the same size, load index, speed rating as those originally provided by Ford. Use of any tire or wheel not recommended by Ford can affect the safety and performance of your vehicle, which could result in an increased risk of loss of vehicle control, vehicle rollover , personal injury and death.
Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be found on the T ire Label on the B-Pillar or the edge of the driver’ s door (vehicles exported outside the US and Canada may not have a T ire Label).
Example only: Cargo W eight – includes all weight added to the Base Curb W eight, including cargo and optional equipment. GA W (Gross Axle W eight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload.
GA WR (Gross Axle W eight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Label located on the B-Pillar or the edge of the driver’ s door .
• Example only: W ARNING: Exceeding the Safety Compliance Certification Label vehicle weight rating limits could result in substandard vehicle handling or performance, engine, transmission and/or structural damage, serious damage to the vehicle, loss of control and personal injury .
W ARNING: Do not use replacement tires with lower load carrying capacities than the original tires because they may lower the vehicle’ s GVWR and GA WR limitations. Replacement tires with a higher limit than the original tires do not increase the GVWR and GA WR limitations.
you have been planning for the past 2 years. Measuring the inside of the vehicle with the rear seat folded down, you have room for 12-100 lb. (45 kg) bags of cement. Do you have enough load capacity to transport the cement to your home? If you and your friend each weigh 220 lb.
Front-wheel drive (FWD) vehicles equipped with a manual transmission: If your vehicle is equipped with a manual transmission, shifting the transmission into neutral permits “flat-towing” (all wheels on the ground) for pulling behind a motorhome. Before you tow your vehicle: • Release the parking brake.
STARTING Positions of the ignition 1. Off — locks the steering wheel, automatic transmission gearshift lever and allows key removal. This position also shuts the engine and all electrical accessories off. 2. Accessory—allows the electrical accessories such as the radio to operate while the engine is not running.
W ARNING: If you smell exhaust fumes inside your vehicle, have your dealer inspect your vehicle immediately . Do not drive if you smell exhaust fumes. Important safety precautions When the engine starts, the idle RPM runs faster to warm the engine. If the engine idle speed does not slow down automatically , have the vehicle checked.
• Make sure the gearshift is in P (Park). If starting a vehicle with a manual transmission: • Make sure the parking brake is set. • Press the clutch pedal to the floor . 3. T urn the key to 3 (on) without turning the key to 4 (start). Some warning lights will briefly illuminate.
Starting the engine 1. T urn the key to 3 (on) without turning the key to 4 (start). 2. T urn the key to 4 (start), then release the key as soon as the engine begins cranking. Y our vehicle has a computer assisted cranking system that assists in starting the engine.
which is installed in your engine block and a wire harness which allows the user to connect the system to a grounded 120 volt A/C electrical source. The block heater system is most effective when outdoor temperatures reach below 0°F (-18°C).
• Be sure that the engine block heater , heater cord and extension cord are solidly connected. A poor connection can cause the cord to become very hot and may result in an electrical shock or fire. Be sure to check for heat anywhere in the electrical hookup once the system has been operating for approximately a half hour .
Four-wheel anti-lock brake system (ABS) Y our vehicle is equipped with an anti-lock braking system (ABS). This system helps you maintain steering control during emergency stops by keeping the brakes from locking.
Parking brake T o set the parking brake (1), pull the parking brake handle up as far as possible. The BRAKE warning lamp will illuminate and will remain illuminated until the parking brake is released. T o release, press and hold the button (2), pull the handle up slightly , then push the handle down.
W ARNING: V ehicle modifications involving braking system, aftermarket roof racks, suspension, steering system, tire construction and/or wheel/tire size may change the handling characteristics of the vehicle and may adversely affect the performance of the AdvanceT rac 威 system.
The AdvanceT rac 威 system includes a stability control button on the center of the instrument panel, and a stability control light in the instrument cluster .
wheel spin by momentarily applying the brakes to the wheel that is slipping. T raction control is most active at low speeds. During TCS events, the stability control light in the instrument cluster will flash.
be beneficial because the wheels are allowed to spin. This will restore full engine power and will enhance momentum through the obstacle. T o switch off the TCS press the stability control button. Full features of the AdvanceT rac 威 system can be restored by pressing the stability control button again or by turning off and restarting the engine.
If the steering wanders or pulls, check for: • An improperly inflated tire • Uneven tire wear • Loose or worn suspension components • Loose or worn steering components • Improper steering alignment A high crown in the road or high crosswinds may also make the steering seem to wander/pull.
See your authorized dealer as soon as possible if this procedure is used. W ARNING: Do not drive your vehicle until you verify that the brake lamps are working. W ARNING: Always set the parking brake fully and make sure the gearshift is latched in P (Park).
P (Park) This position locks the transmission and prevents the front wheels from turning. T o put your vehicle in gear: 1. Start the engine 2. Press the brake pedal 3. Move the gearshift lever into the desired gear T o put your vehicle in P (Park): 1.
D (Drive) without Overdrive Overdrive can be deactivated by pressing the transmission control switch on the side of the gearshift lever . • This position allows for all forward gears (1–3) except overdrive. • Provides engine braking. • Use when driving conditions cause excessive shifting from O/D to other gears.
If your vehicle gets stuck in mud or snow If your vehicle gets stuck in mud or snow , it may be rocked out by shifting between forward and reverse gears, stopping between shifts in a steady pattern.
Recommended shift speeds Do not downshift into 1 (First) when your vehicle is moving faster than 15 mph (24 km/h). This will damage the clutch. Upshift according to the following chart: Recommended up.
DRIVING THROUGH WATER If driving through deep or standing water is unavoidable, proceed very slowly especially when the depth is not known. Never drive through water that is higher than the bottom of the wheel rims (for cars) or the bottom of the hubs (for trucks).
ROADSIDE ASSISTANCE Getting roadside assistance T o fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program.
Canadian customers refer to your W arranty Guide or visit our website at www .ford.ca for information on: Using roadside assistance Complete the roadside assistance identification card and place it in your wallet for quick reference. In the United States, this card is found in the Owner Guide portfolio in the glove compartment.
FUEL PUMP SHUT-OFF SWITCH This device stops the electric fuel pump from sending fuel to the engine when your vehicle has had a substantial jolt. After an accident, if the engine cranks but does not start, this switch may have been activated. This switch is located in the front passenger’ s footwell, behind the kick panel access cover .
Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 2A Grey Grey — — — 3A Violet Violet — — — 4A Pink Pink — — — 5A T an T an — — — 7.
The fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Protected circuits 1 30A Not used (spare) 2 15A Brake switch (high-mount brake lamp) 3 15A Not used (spare) 4 30A Not used (spare) 5.
Fuse/Relay Location Fuse Amp Rating Protected circuits 11 10A Not used (spare) 12 7.5A Power mirrors 13 5A SYNC 威 14 10A Not used (spare) 15 10A Recirculated air , Air conditioning 16 15A Global pos.
Fuse/Relay Location Fuse Amp Rating Protected circuits 39 20A Radio, Center information display , Electronic finish panel 40 20A Not used (spare) 41 15A Door lock/sunroof switch illumination, Auto dimming rear view mirror , Ambient lighting 42 10A Not used (spare) 43 10A Heated seats relay 44 10A Not used (spare) 45 5A Front wipers (logic) 46 7.
T o remove a fuse, use the fuse puller tool provided on the inside of the passenger compartment fuse panel cover . The high-current fuses are coded as follows: Fuse/Relay Location Fuse Amp Rating Prot.
Fuse/Relay Location Fuse Amp Rating Protected circuits 18 20A ABS solenoid 19 — Not used 20 — A/C clutch relay 21A Rear defrost relay 21B — Not used 21C — Blower relay 21D — PCM relay 22 10A.
CHANGING THE TIRES If you get a flat tire while driving, do not apply the brake heavily . Instead, gradually decrease your speed. Hold the steering wheel firmly and slowly move to a safe place on the side of the road. Note: The tire pressure monitoring system (TPMS) indicator light will illuminate when the spare tire is in use.
A dissimilar spare tire/wheel is defined as a spare tire and/or wheel that is different in brand, size or appearance from the road tires and wheels and can be one of three types: 1. T -type mini-spare: This spare tire begins with the letter “T” for tire size and may have “T emporary Use Only” molded in the sidewall 2.
The usage of a full-size dissimilar spare tire/wheel can lead to impairment of the following: • Handling, stability and braking performance • Comfort and noise • Ground clearance and parking at .
Removing the spare tire and jack Remove the spare tire and jack by turning their tie-down bolts counterclockwise. The lug wrench is located in a bag next to, or on top of, the spare tire.
1. Block the diagonally opposite wheel. 2. If equipped with a 6-spoke wheel cover that’ s bolted on, remove the four plastic nuts by turning counterclockwise 1/4 turn for access to the lug nuts. Note: T o avoid damage to the wheel cover , the 6-spoke wheel cover cannot be removed until the tire is off the vehicle.
4. The vehicle jacking points are depicted on the yellow warning label on the jack shown here. Depending on which tire is to be changed, put the jack approximately 7 inches (18 cm) from the front wheel opening (1) or approximately 17 inches (43 cm) from the rear wheel opening (2).
WHEEL LUG NUT TORQUE SPECIFICATIONS Retighten the lug nuts to the specified torque at 500 miles (800 km) after any wheel disturbance (tire rotation, changing a flat tire, wheel removal, etc.). Bolt size Wheel lug nut torque* ft-lb N • m M12 x 1.5 100 135 * T orque specifications are for nut and bolt threads free of dirt and rust.
JUMP STARTING W ARNING: The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. W ARNING: Batteries contain sulfuric acid which can burn skin, eyes and clothing, if contacted.
Connecting the jumper cables Note: In the illustration, the vehicle on the bottom is used to designate the assisting (boosting) battery . 1. Connect the positive (+) jumper cable to the positive (+) terminal of the discharged battery . 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery .
Removing the jumper cables Remove the jumper cables in the reverse order that they were connected. Note: In the illustration, the vehicle on the bottom is used to designate the assisting (boosting) battery . 1. Remove the jumper cable from the ground metal surface.
WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or , if you are a member of a roadside assistance program, your roadside assistance service provider . It is recommended that your vehicle be towed with a wheel lift or flatbed equipment.
Emergency towing In case of a roadside emergency with a disabled vehicle (without access to wheel dollies, car hauling trailer , or flatbed transport vehicle) your vehicle (regardless of transmission .
GETTING THE SERVICES YOU NEED W arranty repairs to your vehicle must be performed by an authorized Ford, Lincoln, or Mercury dealer . While any authorized dealer handling your vehicle line will provide warranty service, we recommend you return to your selling authorized dealer who wants to ensure your continued satisfaction.
In Canada: Mailing address (Ford vehicles) Customer Relationship Centre Ford Motor Company of Canada, Limited P .O. Box 2000 Oakville, Ontario L6J 5E4 T elephone 1-800-565-3673 (FORD) Online www .ford.ca Mailing address (Lincoln vehicles) Lincoln Centre Ford Motor Company of Canada, Limited P .
In the United States, a warranty dispute must be submitted to the BBB AUTO LINE before taking action under the Magnuson-Moss W arranty Act, or to the extent allowed by state law , before pursuing replacement or repurchase remedies provided by certain state laws.
Y ou are required to submit your warranty dispute to BBB AUTO LINE before asserting in court any rights or remedies conferred by California Civil Code Section 1793.22(b). Y ou are also required to use BBB AUTO LINE before exercising rights or seeking remedies created by the Federal Magnuson-Moss W arranty Act, 15 U.
Y ou can get more information by calling BBB AUTO LINE at 1-800-955-5100, or writing to: BBB AUTO LINE 4200 W ilson Boulevard, Suite 800 Arlington, V irginia 22203–1833 BBB AUTO LINE applications can also be requested by calling the Ford Motor Company Customer Relationship Center at 1-800-392-3673.
GETTING ASSIST ANCE OUTSIDE THE U.S. AND CANADA Before exporting your vehicle to a foreign country , contact the appropriate foreign embassy or consulate. These officials can inform you of local vehicle registration regulations and where to find unleaded fuel.
If your vehicle must be serviced while you are traveling or living in the Middle East, contact the nearest authorized dealer . If the authorized dealer cannot help you, contact: Ford Middle East Customer Relationship Center P .O. Box 21470 Dubai, United Arab Emirates T elephone: +971 4 3326084 F AX: +971 4 3327299 Email: menacac@ford.
REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway T raffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company .
W ASHING THE EXTERIOR W ash your vehicle regularly with cool or lukewarm water and a neutral pH shampoo, such as Motorcraft 威 Detail W ash (ZC-3-A), which is available from your authorized dealer . • Never use strong household detergents or soap, such as dish washing or laundry liquid.
• Do not allow paint sealant to come in contact with any non-body (low-gloss black) colored trim, such as grained door handles, roof racks, bumpers, side moldings, mirror housings or the windshield cowl area. The paint sealant will “gray” or stain the parts over time.
• Do not spray a hot engine with cold water to avoid cracking the engine block or other engine components. • Spray Motorcraft 威 Engine Shampoo and Degreaser (ZC-20) on all parts that require cleaning and pressure rinse clean. In Canada, use Motorcraft 威 Engine Shampoo (CXC-66-A).
may cause squeaking or chatter noise from the blades, and streaking and smearing of the windshield. T o clean these items, follow these tips: • The windshield, rear windows and side windows may be cleaned with a non-abrasive cleaner such as Motorcraft 威 Ultra-Clear Spray Glass Cleaner (ZC-23), available from your authorized dealer .
• Do not allow air fresheners and hand sanitizers to spill on interior surfaces. If a spill occurs, wipe off immediately . Damage may not be covered by your warranty . W ARNING: Do not use chemical solvents or strong detergents when cleaning the steering wheel or instrument panel to avoid contamination of the airbag system.
W ARNING: Do not use cleaning solvents, bleach or dye on the vehicle’ s safety belts, as these actions may weaken the belt webbing. W ARNING: On vehicles equipped with seat-mounted airbags, do not use chemical solvents or strong detergents.
Cleaning For dirt, use a vacuum cleaner then use a clean, damp cloth or soft brush. For routine cleaning, wipe the surface with a soft, damp cloth. For more thorough cleaning, wipe the surface with a mild soap and water solution. • Clean spills as quickly as possible.
FORD AND LINCOLN MERCURY CAR CARE PRODUCTS Y our Ford or Lincoln Mercury authorized dealer has many quality products available to clean your vehicle and protect its finishes. These quality products have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and appearance of your vehicle.
SERVICE RECOMMENDATIONS T o help you service your vehicle, we provide scheduled maintenance information which makes tracking routine service easy . If your vehicle requires professional service, your authorized dealer can provide the necessary parts and service.
W ARNING: T o reduce the risk of vehicle damage and/or personal burn injuries, do not start your engine with the air cleaner removed and do not remove it while the engine is running. OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the instrument panel.
IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 1. Engine oil filler cap 2. Brake/Clutch fluid reservoir 3. Power distribution box 4. Battery 5. Air filter 6. Automatic transmission fluid dipstick (if equipped) 7. Engine oil dipstick 8. Power steering fluid reservoir 9.
WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if the level is low . In very cold weather , do not fill the reservoir completely . Only use a washer fluid that meets Ford specifications. Do not use any special washer fluid such as windshield water repellent type fluid or bug wash.
T o prolong the life of the wiper blades, it is highly recommended to scrape off the ice on the windshield before turning on the wipers. The layer of ice has many sharp edges and can damage the micro edge of the wiper rubber element.
2. If the engine oil level is not within the normal range, add only certified engine oil of the recommended viscosity . Remove the engine oil filler cap and use a funnel to pour the engine oil into the opening. 3. Recheck the engine oil level. Make sure the oil level is not above the MAX mark on the engine oil level dipstick.
Change your engine oil and filter according to the appropriate schedule listed in the scheduled maintenance information. Ford production and Motorcraft 威 replacement oil filters are designed for added engine protection and long life.
W ARNING: When lifting a plastic-cased battery , excessive pressure on the end walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery . Lift the battery with a battery carrier or with your hands on opposite corners.
this, the transmission may shift firmly when first driven. This operation is considered normal and will fully update transmission operation to its optimum shift feel. If the battery has been disconnected or a new battery has been installed, the clock and the preset radio stations must be reset once the battery is reconnected.
When the engine is cold, check the level of the engine coolant in the reservoir . • The engine coolant should be at the FULL COLD level, or within the COLD FILL or MIN / MAX range as listed on the engine coolant reservoir (depending upon application).
and new (unused) coolant together in the vehicle. Mixing of engine coolants may harm your engine’ s cooling system. The use of an improper coolant may harm engine and cooling system components and may void the warranty . Refer to Maintenance product specifications and capacities in this chapter .
5. Fill the coolant reservoir slowly with the proper coolant mixture, to within the COLD FILL RANGE or the FULL COLD level on the reservoir . If you removed the radiator cap in an overflow system, fill the radiator until the coolant is visible and radiator is almost full.
• A coolant concentration of 60% will provide freeze point protection down to -62°F [-52°C]. Increased engine coolant concentrations above 60% will decrease the overheat protection characteristics of the engine coolant and may cause engine damage.
When this occurs the vehicle will still operate. However: • The engine power will be limited. • The air conditioning system will be disabled. Continued operation will increase the engine temperature: • The engine will completely shut down. • Steering and braking effort will increase.
WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELS Important safety precautions W ARNING: Do not overfill the fuel tank. The pressure in an overfilled tank may cause leakage and lead to fuel spray and fire.
• A void getting fuel liquid in your eyes. If fuel is splashed in the eyes, remove contact lenses (if worn), flush with water for 15 minutes and seek medical attention. Failure to seek proper medical attention could lead to permanent injury . • Fuels can also be harmful if absorbed through the skin.
Use the following guidelines to avoid electrostatic charge build-up when filling an ungrounded fuel container: • Place approved fuel container on the ground. • DO NOT fill a fuel container while it is in the vehicle (including the cargo area). • Keep the fuel pump nozzle in contact with the fuel container while filling.
W ARNING: The fuel system may be under pressure. If the fuel filler cap is venting vapor or if you hear a hissing sound, wait until it stops before completely removing the fuel filler cap.
Do not be concerned if your engine sometimes knocks lightly . However , if it knocks heavily under most driving conditions while you are using fuel with the recommended octane rating, see your authorized dealer to prevent any engine damage.
• The service engine soon indicator may come on. For more information on the service engine soon indicator , refer to W arning lights and chimes in the Instrument Cluster chapter . ESSENTIALS OF GOOD FUEL ECONOMY Measuring techniques Y our best source of information about actual fuel economy is you, the driver .
Y our results will be most accurate if your filling method is consistent. Calculating fuel economy 1. Fill the fuel tank completely and record the initial odometer reading (in miles or kilometers). 2. Each time you fill the tank, record the amount of fuel added (in gallons or liters).
• Revving the engine before turning it off may reduce fuel economy . • Using the air conditioner or defroster may reduce fuel economy . • Y ou may want to turn off the speed control in hilly terrain if unnecessary shifting between the top gears occurs.
EMISSION CONTROL SYSTEM Y our vehicle is equipped with various emission control components and a catalytic converter which will enable your vehicle to comply with applicable exhaust emission standards. T o make sure that the catalytic converter and other emission control components continue to work properly: • Use only the specified fuel listed.
Do not make any unauthorized changes to your vehicle or engine. By law , vehicle owners and anyone who manufactures, repairs, services, sells, leases, trades vehicles, or supervises a fleet of vehicles are not permitted to intentionally remove an emission control device or prevent it from working.
Readiness for Inspection/Maintenance (I/M) testing Some state/provincial and local governments may have Inspection/Maintenance (I/M) programs to inspect the emission control equipment on your vehicle. Failure to pass this inspection could prevent you from getting a vehicle registration.
POWER STEERING FLUID Check the fluid. Refer to scheduled maintenance information. 1. Start the engine and let it run until it reaches normal operating temperature. 2. T urn the steering wheel left and right several times. 3. T urn the engine off. 4. Check the fluid level.
(approximately 20 miles [30 km]). If your vehicle has been operated for an extended period at high speeds, in city traffic during hot weather or pulling a trailer , the vehicle should be turned off for about 30 minutes to allow fluid to cool before checking.
High fluid level Fluid levels above the safe range may result in transmission failure. An overfill condition of transmission fluid may cause shift and/or engagement concerns and/or possible damage. High fluid levels can be caused by an overheating condition.
Checking and adding manual transmission fluid (if equipped) 1. Clean the filler plug. 2. Remove the filler plug and inspect the fluid level. 3. Fluid level should be at the bottom of the opening. 4. Add enough fluid through the filler opening so that the fluid level is at the bottom of the opening.
6. Replace the air filter housing cover and secure the clamps. Be sure that the air cleaner cover tabs are engaged into the slots of the air cleaner housing.
• Start the engine every 15 days. Run at fast idle until it reaches normal operating temperature. • W ith your foot on the brake, shift through all the gears while the engine is running. Fuel system • Fill the fuel tank with high-quality fuel until the first automatic shutoff of the fuel pump nozzle.
Removing vehicle from storage When your vehicle is ready to come out of storage, do the following: • W ash your vehicle to remove any dirt or grease film build-up on window surfaces. • Check windshield wipers for any deterioration. • Check under the hood for any foreign material that may have collected during storage (mice/squirrel nests).
MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIES Item Capacity Ford Part Name or Equivalent Ford Part Number / Ford Specification Brake fluid (and clutch fluid–if equipped) Between MIN and MAX on r.
Item Capacity Ford Part Name or Equivalent Ford Part Number / Ford Specification Engine oil 4.5 quarts (4.3L) • Motorcraft 威 SAE 5W -20 Premium Synthetic Blend Motor Oil (US) • Motorcraft 威 SA.
Item Capacity Ford Part Name or Equivalent Ford Part Number / Ford Specification W indshield washer fluid Fill as required Motorcraft 威 Premium W indshield W asher Concentrate (US) Premium Quality W indshield W asher Fluid (Canada) ZC-32-A (US) CXC-37-(A, B, D, and F) (Canada) / WSB-M8B16-A2/- - Fuel tank 13.
ENGINE DATA Engine 2.0L I4 engine Cubic inches 121 Required fuel 87 octane Firing order 1–3–4–2 Ignition system C.O.P Compression ratio 10.0:1 Spark plug gap .
Engine drivebelt routing IDENTIFYING YOUR VEHICLE Safety Compliance Certification Label The National Highway T raffic Safety Administration Regulations require that a Safety Compliance Certification Label be affixed to a vehicle and prescribe where the Safety Compliance Certification Label may be located.
V ehicle identification number (VIN) The vehicle identification number is located on the driver side instrument panel. Please note that in the graphic, XXXX is representative of your vehicle identification number . The V ehicle Identification Number (VIN) contains the following information: 1.
T RANSMISSION CODE DESIGNATIONS Y ou can find a transmission code on the Safety Compliance Certification Label. The following table tells you which transmission each code represents.
FORD CUSTOM ACCESSORIES FOR YOUR VEHICLE A wide selection of Ford Custom Accessories are available for your vehicle through your local Ford or Ford of Canada dealer .
Lifestyle • Ash cup / smoker’ s package • Garmin navigation* • Rear bumper protector* • Roof racks and carriers* • Cargo net* • Cargo organization and management Peace of mind • Keyles.
• Mobile communications systems may harm the operation of your vehicle, particularly if they are not properly designed for automotive use. • T o avoid interference with other vehicle functions, su.
FORD ESP EXTENDED SERVICE PLANS (U.S. ONLY) More than 30 million Ford, Lincoln, and Mercury owners have discovered the powerful protection of Ford ESP . It is the only extended service plan backed by Ford Motor Company , and provides “peace of mind” protection beyond the New V ehicle Limited W arranty coverage.
Ford ESP Can Quickly Pay for Itself One service bill – the cost of parts and labor – can easily exceed the price of your Ford ESP Service Contract.
Ford Extended Service Plan 271 201 1 Focus (foc) Owners Guide, 1st Printing USA (fus).
FORD ESP EXTENDED SERVICE PLANS (CANADA ONLY) Y ou can get more protection for your vehicle by purchasing a Ford Extended Service Plan (ESP). Ford ESP is the only service contract backed by Ford Motor Company .
GENERAL MAINTENANCE INFORMATION Why maintain your vehicle? This guide describes the scheduled maintenance required for your vehicle. Carefully following this schedule helps protect against major repair expenses resulting from neglect or inadequate maintenance and may also help to increase the value of your vehicle when you sell or trade it.
Ford strongly recommends the use of genuine Ford replacement parts. Parts other than Ford, Motorcraft 威 or Ford-authorized remanufactured parts that are used for maintenance replacement or for the service of components affecting emission control must be equivalent to genuine Ford Motor Company parts in performance and durability .
Factory-trained technicians Ford and Lincoln Mercury service technicians participate in extensive factory-sponsored certification training to help them become experts on the operation of your vehicle. Ask your dealership about the training and certification their technicians have received.
Multi-point inspection In order to keep your vehicle running right, it is important to have the systems on your vehicle checked regularly . This can help identify potential issues and prevent major problems.
Be sure to ask your Ford or Lincoln Mercury dealership service advisor or technician about the multi-point vehicle inspection. It’ s a comprehensive way to perform a thorough inspection of your vehicle. It’ s your checklist that gives you immediate feedback on the overall condition of your vehicle.
Scheduled Maintenance Guide 278 201 1 Focus (foc) Owners Guide, 1st Printing USA (fus).
NORMAL SCHEDULED MAINTENANCE AND LOG The following section contains the “Normal Schedule”. This schedule is presented at specific mileage (kilometer) intervals with exceptions noted.
Miles (x 1,000)* 7.5 15 22.5 30 37.5 45 52.5 60 67.5 75 Kilometers (x 1,000)* 12 24 36 48 60 72 84 96 108 120 Months* 6 12 18 24 30 36 42 48 54 60 Change engine oil and filter • ••••••••• Rotate tires, inspect tire wear and measure tread depth.
Miles (x 1,000)* 82.5 90 97.5 105 112.5 120 127.5 135 142.5 150 Kilometers (x 1,000)* 132 144 156 168 180 192 204 216 228 240 Months* 66 72 78 84 90 96 102 108 114 120 Change engine oil and filter • ••••••••• Rotate tires, inspect tire wear and measure tread depth.
Every 15,000 miles (24,000 km) Replace cabin air filter (if equipped) Every 30,000 miles (48,000 km) Replace climate-controlled seat filter (if equipped) Replace engine air filter Replace fuel filter .
Maintenance schedule log D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : D EALER V ALIDATION : P&A C ODE.
D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M.
D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M.
SPECIAL OPERATING CONDITIONS If you operate your Ford/Lincoln/Mercury vehicle primarily in one of the more demanding Special Operating Conditions listed below , you will need to have some items maintained more frequently .
Extensive idling and/or low-speed driving for long distances as in heavy commercial use such as delivery , taxi, patrol car or livery Inspect frequently , service as required – Replace cabin air filter (if equipped). – Replace engine air filter . Every 5,000 miles (8,000 km) – Inspect brake system.
Crown Victoria police interceptor & taxi, and Executive Series T own Car equipped with engine idle hour meter Inspect frequently , service as required – Replace cabin air filter (if equipped). Every 5,000 miles (8,000 km) – Inspect brake system.
ENGINE IDLE HOUR METER (IF EQUIPPED): Y our vehicle may be equipped with an idle meter to indicate how much time the vehicle is idling in P (Park) or N (Neutral). The meter is incorporated with the vehicle odometer . Depressing the odometer -reset button once will display the trip odometer (miles [km] followed by a “T” for trip odometer).
Operating in dusty conditions such as unpaved or dusty roads Inspect frequently , service as required – Replace cabin air filter (if equipped). – Replace engine air filter . Every 5,000 miles (8,000 km) – Inspect wheels and related components for abnormal noise, wear , looseness or drag.
Special operating condition log D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : D EALER V ALIDATION : P&.
D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M.
EXCEPTIONS In addition, there are several exceptions to the Normal Schedule. They are listed below: Normal vehicle axle maintenance ❑ Rear axles and power take-off (PTO) units containing synthetic lubricant and light duty trucks equipped with Ford-design axles are lubricated for life.
COOLANT CHANGE RECORD Engine coolant ❑ 6 years or 105,000 miles (168,000 km) - change coolant (whichever comes first). ❑ After initial change - change coolant every 3 years or 45,000 miles (72,000 km).
Engine coolant change log D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : D EALER V ALIDATION : P&A C OD.
A AdvanceT rac .............................. 178 Air cleaner filter ...............255, 258 Air conditioning manual heating and air conditioning system ................. 42 Airbag supplemental restraint system ................110–111, 119, 121 and child safety seats .
Child safety seats - booster seats ........................................... 140 Cleaning your vehicle engine compartment ..............220 instrument panel .................... 222 interior ..................................... 223 plastic parts ..
filter , specifications ........232, 258 recommendations ................... 232 refill capacities ........................ 259 specifications .......................... 259 Event data recording .................... 7 Exhaust fumes ...................
K Keyless entry system autolock ..................................... 74 Keys ............................................. 84 positions of the ignition ......... 171 L Lamps bulb replacement specifications chart .................. 51 daytime running light .
R Radio ............................................ 25 Recommendations for attaching safety restraints for children ...................................... 127 Relays ........................................ 192 Remote entry system ................. 79 illuminated entry .
T ires ........................... 144–145, 199 alignment ................................ 152 care .......................................... 148 changing .......................... 199, 202 checking the pressure ............ 148 inflating ........
Een belangrijk punt na aankoop van elk apparaat Ford 2011 Focus (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Ford 2011 Focus heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Ford 2011 Focus vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Ford 2011 Focus leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Ford 2011 Focus krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Ford 2011 Focus bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Ford 2011 Focus kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Ford 2011 Focus . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
